GE(S)/M-56/2023-24

Amount

Excavating over areas, n exc 1.5 m deep and getting out in any type of soil complete all as specified and directed.

Excavating over areas, exc 1.5 m and n.exc 3.00 m deep and getting out in any type of soil complete all as specified and directed.

Returning, filling in (soil), including spreading, leveling, watering and well ramming in layers not exc. 25 cm complete all as specified and directed.

Removing excavated material (soil) n.exc. 50 m and depositing where directed at a level n. exc. 1.5 m above the starting point complete all as specified and directed.

Forming embankments including raising (or lowering) earth, spreading in layers n exc. 30 cm thick; watering, ramming/rolling and finishing to required size, shape, etc., n exc. 1.5 m high from base in any type of soil complete all as specified and directed.

M&L for PCC 1:4:8 type D2 (using 40 mm graded crushed stone aggregates) as in foundation, filling and mass concrete complete all as specified and directed.

M&L for RCC M-25 (design mix) walls, retaining walls, basement walls, ballast walls and the like; any thickness; above top of footings; including attached pilasters and buttresses complete all as specified and directed.

M&L for form work to sides of flat, rough finished surfaces of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work; vertical to batter complete all as specified and directed.

M&L for Formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillasters, buttresses, etc.; vertical or to batter complete all as specified and directed.

M&L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L for mild steel TMT bars 6mm to 8mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L for 15mm thick rendering on faces of brick work or concrete surfaces in cement mortar 1:4, with WPC finished even and smooth without using extra cement complete all as specified and directed. (WPC measured & paid separetely)

M&L for 15mm thick rendering on faces of brick work or concrete surfaces in cement mortar 1:4, finished even and smooth without using extra cement complete all as specified and directed.

Supply only liquid water proofing compound complete all as specified and directed.

S&F framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and directed.

M&L for brick work with fly ash bricks, old size bricks, straight or curved on plan exc 6 mtr mean radius built in CM (1:6) complete all as specified and directed.

Excavating in trenches in any type of soil, n. exc. 1.5 m wide and n. exc. 1.5 m in depth, for foundation, etc. or for shafts, wells, cess pits, manholes, pier holes, etc n. exc. 10 sqm on plan and n.exc 1.5 m in depth and getting out complete all as specified and directed.

M&L for cutting to existing GI distribution pipe line of size 40mm to 50mm dia in situ for adding/alteration. Branch connection and insertion of Tee, including necessary earth work complete all as specified & directed.

S&F of GI tubing light grade 40 mm bore cut to size and fixed along the pole for cable protection including clamp 02 Nos of size 25x4 mm, nut bolts , washers etc all as required at site including taking out old one complete all as specified and directed.

S&F for gun-metal globe or gate valves 20mm with iron wheel head, screwed both ends, for iron pipe and fixed complete all as specified and directed.

M&L for brick work with fly ash bricks, old size bricks, straight or curved on plan exc 6 mtr mean radius built in CM (1:4) complete all as specified and directed.

M&L for 10mm thick rendering on faces of brick work or concrete surfaces in cement mortar 1:4, finished even and smooth without using extra cement complete all as specified and directed.

M&L for 15mm thick rendering in two layers (5mm thick in CM 1:4 over 10mm thick in CM 1:6) on brick work and concrete surfaces of wall, finished the surface even and smooth without using extra cement, mixing and including WPC @ 200ml/bag of cement in top layer only complete all as specified and directed.

S&F 3.0mm thick figured (frosted) sheet glass, ordinary quality and glazing with oil putty in square not exc 0.50 Sqm in each pane, complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples, complete all as specified and directed.

M&L for PCC 1:2:4 type B1 (using 20 mm graded crushed stone aggregate) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, haunching, benching, kerbs , mud stops, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and directed.

M&L for RCC M-25 (design mix) using 20 mm graded stone aggregate in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies and in shelves and the like complete all as specified and directed.

M&L for RCC M-25 (design mix) using 20 mm graded stone aggregate in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc. basement slabs and mass concrete complete all as specified and directed.

M&L for form work to soffits of flat, rough finished surfaces of concrete of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick(Horizontal or sloping) complete all as specified and directed.

M&L for form work to sides and soffits of flat, rough finished surfaces of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed.

M&L for form work to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, opening in concrete walls, floor and roofs and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc. 10 cm but n. exc. 20 cm wide, rough finished surfaces of concrete complete all as specified and directed.

M&L for mild steel TMT bars 5 mm dia and over up to and including 10 mm dia in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed.

M&L for preparation of newly surfaces of steel of any description over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer on exposed surfaces complete all as specified and directed.

M&L for preparation of newly plastered or unplastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

M&L for preparation of newly plastered or unplastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M&L for hard core of broken stone or boulders of gauge n. exc. 63 mm, deposited, spread and leveled in layers n. exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for 100 mm thick PCC 1:5:10 type E-2 (using 40 mm graded crushed stone aggregate) in sub base of floors complete all as specified and directed.

M&L for 40 mm thick PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) in sub base of floors complete all as specified and directed.

Surface excavation n.exc(not exceeding) 30 cm deep and averaging 15cm deep and getting out in any type of soil complete all as specified and directed.

M&L for 75 mm thick PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) in sub base of floors complete all as specified and directed.

M&L for 25 mm thick PCC 1:4:8 type D-2 (using 40 mm graded crushed stone aggregate) in sub base of floors complete all as specified and directed.

M&L for coloured machine pressed precast rubber moulded concrete interlocking (Grey/red/yellow) paver block of any shape and size with 6-8mm white cement layer mixed with pigment and coated with epoxy coating having high glossy finish confirming to IS 15658-2006 of 60mm thickness, M-35 Grade, laid dry over and including 50 mm thick screened river washed sand cushion, complete all as specified and directed.

Surface dressing n. exc. 15 cm deep and getting out in any type of soil complete all as specified and directed.

M&L for brick work with fly ash bricks, old size half thick bricks, straight or curved on plan exc 6 mtr mean radius built in CM (1:4) complete all as specified and directed.

M&L for RCC M-25 (design mix) using 20 mm graded stone aggregate in beams, cantilevers, bressumers, lintels, shelves complete all as specified and directed.

M&L for 10mm thick rendering on faces of brick work or concrete surfaces of walls in cement mortar 1:6, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 5mm thick in CM 1:3 on concrete surfaces of ceiling / top and sides of chajjas/facia of roof projection including necessary formwork, finishing the surface even and smooth without using extra cement complete all as specified and directed.

M&L for 10mm thick rendering in CM 1:3 mixing with liquid water proofing compound @ 0.200 ltr per 50 kg bag of cement, on roof slab when concrete is green, finished even and smooth without using extra cement complete all as specified and directed. Note :- WPC shall be measured and paid separately under respective item of BOQ.

S&F factory made single extruded WPC (Wood Polymer Composit) solid door/windows/ceosetory windows & other frames/chowkhat of size 45 x 70mm comprising of vigin PVC polymer of K value 58-60 (suspension grade), calcium carbonate & natural fibres (wood powder/rice husk/ weat husk) and non additives (maximum toxicity index of 12 for 100gms) fabricated with mitre joints after applying PVC solvent cement and screwed with fully body threaded star headed SS screws having minimum frame density of 750kg/cum, screw withdrwal strenght of 2200N (face), 1100n (edge), minimum compressive strength 58 N/Sqmm , modulas of elasticity 900N/sqmm and resistence to spread of flame of Class A category with property of being termite /borer proof, water/moisture proof and fire retrdant and fixed position MS hold fast/lugs/SS dash fasteners of required dia and length (MS hold fasts/lugs or SS fasteners shall be paid separately) complete all as specified and directed Note :- i) WPC solid door / window frames minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable but no extra payment on this account shall be made.ii) Material manufactured by MES approved firms / ISI approved firms shall only be used in the work. IS certificate alongwith MTC to be produced before execution of work.

S&F box type steel windows comprised of tubular frame and shutters made out of 1.25 mm thick M S sheet tube factory made with double side shutters wire gauged shutter & glass glazed shutter (wire cloth and glass panes only shall be measured and paid seperately) with side hung shutters with steel handle and steel peg stay dovetailed or welded incl 2 Nos tower bolts 100 mm long for each leaf and 10 mm square bar grills at spacing as shown on drg welded to FI frame work, including other fittings, hinges, handles, tarred hold fasts, PCC blocks etc all as shown on drg No CEPZ/TD-354/09 sheet 1/3 to 3/3 complete all as specified and directed.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, suppling & fixing in the frame at site, complete all as per specifications & drawing.

S&F 100mm long butt hinges, medium weight, stainless steel, (ISI) marked complete all as specified and directed.

S&F 150mm long, aluminium anodised, barrel tower bolts of extruded section, ISI marked, complete all as specified and directed.

S&F 150 mm long extruded aluminium alloy handles, cast type, anodised complete all as specified and directed.

S&F for floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S&F Rotational moulded polyethlene water storage tank of capacity 1000 Litres, three layers (cylindrical vertical with closed top), hoisted and fixed in position, including 20mm dia PVC ball valve, high pressure of PTMT epoxy coated aluminium rod and high density plastic ball screwed for iron pipe fixed in position (min. wt. 20mm-210gm/25mm-455gm) complete all as specified in SSR Part-1 and directed.

M&L for 20mm bore water tubes 'medium grade' galvanised with all fitting and fixed complete to walls and ceilings or laid in floors, complete all as specified and directed.

M&L for 15mm bore water tubes 'medium grade' galvanised with all fitting and fixed complete to walls and ceilings or laid in floors, complete all as specified and directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc; and cutting chases for concealed water tubing ,etc., and making good, cutting not exc 20 cm girth in brick walls, complete all as specified.

S&F Vitreous china wash down water closet pan (pedestal pattern), white complete including fixing to trap including PVC seat and cover with hinging device for pedestal pan and connecting etc, complete all as specified and directed.

S&F PVC low level flushing cistern, valveless, syphonic action type, 10 litres capacity with inlet ball valve and handle with and including brackets and PVC bend pipe 60/90cm long etc, complete all as specified and directed.

S&F vitreous china wash hand basin flate back or angle back type, white of bowl size 550mm x 400mm including CP pillar tap but including CP brass waste coupling and rubber plug, porcelain stopper, a pair of CI brackets, waste pipe of 32mm dia, complete all as specified and directed.

S&F PVC connection 15mm size of length 450mm with PTMT nuts, complete all as specified and directed.

S&F health foucet (ABS body) mild steel CP hand shower 15mm dia, 1.25mtr long flexible pipe, wall hook, complete all as specified and directed.

S&F 15mm bore bib tap, with flange, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed.

S&F Stop valve/Angle valve (ISI Marked), fancy type cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15 mm bore ccomplete all as specified and as directed.

S&F for stop valve (ISI Marked) 15 mm bore fancy type, chromium plated with long shank and cup (concealed type), cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 15 mm bore complete all as specified and as directed.

S&F for Shower rose swivel type brass chromium plated 150x150 mm size including fixing to steel pipe or unions complete all as specified and as directed.

S&F stainless steel soap dish approximate size 160mmx160mmx90mm complete all as specified and directed.

S&F 140mm size PTMT (minimum weight 50gms) grating doom with or without waste hole fixing in floors, complete all as specified and directed.

S & F Brass CP towel rail 20mm dia 'D' type 60 cm long between flanges complete all as specified and directed.

S&F 75mm bore PVC (SWR) floor trap, plain with grating including jointing with solvent cement, complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipes, single socketed, in any length with rubber ring joints, laid or fixed in trenches / floors / walls, complete all as specified and directed.

S&F 75mm bore PVC (SWR) bend, plain including jointing with solvent cement, complete all as specified and directed.

M&L 75 mm dia bore PVC (SWR) cowls complete all as specified and directed.

M&L for glazed ceramic coloured tiles of size 300mm x 450mm x 7mm thick on vertical surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile over and including rendering 10mm thick in CM 1:4 and finished rough to receive tiles complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick, area of each tile exc 0.11 Sqm but not exc 0.18 Sqm as in floors etc, set and jointed (joint free) in neat cement slurry and pointed in coloured cement to match the shade of tile over and including 15mm thick screed bed or bedding layers in CM 1:4 for laying floor finishescomplete all as specified and directed.

M&L for 75mm thick cement concrete 1:3:6, type C-1 (using 20mm graded crushed stone aggregate) as in plinth protection and paving, laid in slope, finished even and fair including making joints at every 2.5 mtr and at corner filled with bitumen 85/25 and sand in ratio 1:2 by weight, complete all as specified and directed.

M&L for APP modified roof treatment over existing accessible/non accessible RCC roof slab/chajjah/canopy/parapet wall to be executed through approved applicator of the membrane manufacturer with following specification etc.,complete all as specified and directed:- (a)Applying 1st course of 20 mm thick screed bed with cement mortar 1:4 over old concrete surface mixed with liquid water proofing compound. (b)Applying 2nd course of bitumenous primer @ 0.4 kg/Square Metre conforming to IS-3384 over screed bed . (c)Applying 3rd course of a coat of bonding material with blown type bitumen of grade 85/25 heating to working temperature of 180 centigrade and applied @ 1.2 kg/Square Metre. (d)Applying 4th course of APP (Atactic Polypropylene) modified polymeric 3mm thick, weight not less than 3.6 kg/Square Metre with 160 Grams/Square Metre non woven polyster made at center core reinforced laid with 75 mm side overlap and 100 mm overlap. The membrane shall be laid with LPG torch and overlap sealed and finished neat. (e)Applying 5th course of a coat of bonding material with blown type bitumen of grade 85/25 heating to a working temperature of 180 centigrade and applied @ 1.2 kg/Square Metre . (f) Applying a coat of bitumenous based aluminium paint as finishing coat. Complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 (using 40 mm graded crushed stone aggregates) as in foundation, filling and mass concrete complete all as specified and directed.

M&L for concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested in cement concrete 1:4:8, type D-2 (using 40mm graded crushed stone aggregates), complete all as specified and directed.

M&L for Sail-glazed stoneware drain pipes grade 'A' laid in trenches and jointed in CM 1:1 and tested for size 150mm internal dia of pipe as specified, complete all as specified and directed.

M&L for Salt-glazed stoneware drain pipes grade 'A' laid in trenches and jointed in CM 1:1 and tested for size 100mm internal dia of pipe as specified, complete all as specified and directed.

M&L for rolled section conforming to Fe-290 (Gde E-165) as in purlins,rafter,rails amd fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) incl distance pieces, cleats etc complete all as specified and directed.

Cutting into existing manholes for connecting new drains, making good pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching as required and making good for 150mm bore pipe complete all as specified and directed.

M&L for form work to sides of square, rectangular or polygonal, rough finished surfaces of concrete of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed.

M&L for RCC M-25 (design mix) using 20 mm graded stone aggregate in columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for RCC M-25 (design mix) using 20 mm graded stone aggregate in chajjas complete all as specified and directed.

M&L for Machine cut pre-polished kota stone slab flooring 18-20 mm thick laid over & including 20 mm thick screed base in CM 1:4, jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, grinding and polishing machine to yield mirror finish, complete all as specified and directed.

Preparation of newly plastered surfaces of external wall and applying two coats of cement base paint including curing before and after, including a coat of alkali-resistant priming paint complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall by applying 2mm thick wall care putty to make the surface smooth and applying two coats of oil bound distemper complete all as specified and directed.

S&F 3.0mm thick plain sheet glass, ordinary quality and glazing with oil putty in square not exc 0.50 Sqm in each pane, complete all as specified and directed.

S&F pressed steel frame made out of MS sheet 1.25mm thick of size 125mm x 60mm for doors / windows with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. including filling of concrete 1:3:6 type C-0 (12.5mm graded stone aggregate) as in back of chowkhats and including two coats of synthentic enamel paint over a coat of red oxide primer, complete all as specified and directed.

S&F for factory made 35mm thick 2nd class hard wood Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

M&L for preparation of newly surfaces of wood over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer on exposed surfaces complete all as specified and directed.

S&F 200mm long, aluminium anodised, barrel tower bolts of extruded section, ISI marked, complete all as specified and directed.

S&F 300 mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

M&L for 75 mm thick PCC 1:3:6 type C-2 (using 40 mm graded crushed stone aggregate) in sub base of floors complete all as specified and directed.

Taking down chowkhats or frames exc 1.5 Sqm but not exc 4.0 Sqm each (without taking off shutters from the frame), complete all as specified and directed.

Taking down chowkhats or frames not exc 1.5 Sqm each with shutter (without taking off shutters from the frame), complete all as specified and directed.

S&F pressed steel frame of size 105mm x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate including filling of PCC 1:3:6 type C-0 (using 12.5mm graded stone aggregates) in frames/hold fast blocks, complete all as specified and directed.

S&F anodised aluminium frame for doors,windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F for anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc.complete all as specified and directed.

S&F Door closer hydraulically regulated, designation No. 3, universal type, aluminum body (extruded) suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed.complete all as specified and directed.

Taking down roof trusses, coupled rafters or trussed beams of span exc 4m but n.exc 8m complete all as sepecified and directed.

Dismantling timber scantlings 40 sq. cm and over in section, in any position complete all as sepecified and directed.

S&F tubular framed steel trusses (all as per pattern of existing dismantled trusses) made out of MS medium grade tube (ERW or induction butt welded ) upto 60mm bore conforming to I. S.1161-1979 grade St.-240 quality 'A', including welding of distance pieces, cleats, special shaped washer etc. and applying two coat of synthetic enamel paint over a coat of red oxide primer on exposed surfaces complete all as specified and directed.

S&F for mild steel screw bolts machine made with hexagoanl or square heads at one end and screwed the other on screwed both ends each screwed to be fitted with washers and one hexagonal or square nut langth of boltn exc 5cm ong and 11 to 15 mm dia complete all as specified and directed.

M & L for P. C.C type B-1, 1:2:4 ( using 20mm graded aggregate) as in coloumns for fixing trusses complete all as specified and directed.

Dismantling of plain or corrugated AC sheeting, any gauge, thickness, including ridge etc as in roof covering complete all as specified and directed.

S&F for Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550Mpa as in roof covering / cladding to wall, fixed with self tapping screws as specified complete all as specified and directed.

S&F for Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550Mpa as in roof covering / cladding to wall, fixed with self tapping screws as specified complete all as specified and directed.

M&L for false ceiling of 8 mm thick gypsum tiles (600x600mm) laminated with PVC film on the face side & metalised polyester film on the back side with all four edges sealed with PVC film (shade either plain white or crack) fixed using T grid/Cross-T/Wall angle/level clip & suspenders of standard galvanised sections in a grid size of 600x600mm, including taking down existing ceiling board & grid work etc of any type/pattern complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick, area of each tile exc 0.11 Sqm but not exc 0.18 Sqm as in floors etc, set and jointed (joint free) in neat cement slurry and pointed in coloured cement to match the shade of tile over and including 15mm thick screed bed or bedding layers in CM 1:4 for laying floor finishes including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premisescomplete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick, area of each tile exc 0.18 Sqm but not exc 0.38 Sqm as in floors etc, set and jointed (joint free) in neat cement slurry and pointed in coloured cement to match the shade of tile over and including 15mm thick screed bed or bedding layers in CM 1:4 for laying floor finishes including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premisescomplete all as specified and directed.

M&L for glazed ceramic coloured tiles of size 300mm x 450mm x 7mm thick on vertical surfaces, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile over and including rendering 10mm thick in CM 1:4 and finished rough to receive tiles including dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for 10mm thick vitrified ceramic 'light shade' colour tile (Square or Rectangular), polished, area of each tile exc 0.11 Sqm but not exc 0.18 Sqm as in floors etc, set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tile over and including 15mm thick screed bed or bedding layers in CM 1:4 and finished rough including dismantling existing floor finishes, complete all as specified and directed.

S&F 20mm bore stainless steel drapery rod with 1.0mm thick PVC wood grain coating including brackets and knobs, fixed on windows and doors for hanging curtains, complete all as specified and directed.

Demolition of paver block of any description or thickness in floors laid dry, complete all as specified and directed

M&L for coloured machine pressed precast rubber moulded concrete interlocking (Grey/red/yellow) paver block of any shape and size having high glossy finish confirming to IS 15658-2006 of 60mm thickness epoxy coated, M-35 Grade, laid dry over and including 50mm thick washed river sand as approved complete all as specified and directed.

Taking down cement plaster on brick walls or stone walls or concrete surface of any description etc including raking out joints, hacking for key, scrubbing down with water etc., complete all as specified and directed.

M&L for applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litr and UV resistance as per IS 15489:2004, alkali & fungel resistance, dirt resistance exterior paint of required shade (company depot tinted) with silicone additives @ 1.43 litre/10sqm over and including priming coat of exterior primer applied @ 0.9 litre/10sqm over new surfaces complete all as specified & directed.

Demolition of existing brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles, including removal of deberies out of MoD land complete all as specified and directed.

S&F for factory made 35mm thick 2nd class hardwood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkatsr complete all as specified and directed.

M&L for 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

S&F 250 mm long aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F for Framed brackets of angles or tees with web and flanges cut to shape, drilled and countersunk for screw, including bending and welding angles, as necessary, gusset plates, riveting, etc.. n exc 10 kg each brackets, conforming to Fe.290.Gde-E-165 incl dismantling of existing complete all as specified and directed.

Demolition of existing reinforced cement concrete of any description & in any position not otherwise specifically provided forcomplete all as specified and directed

M&L for point wiring for one light point / fan point / bell point controlled by one switch with 1.5 Sqmm PVC insulated unsheathed copper conductor single core multistranded FRLS (RYB) for phase, black for neutral and 1.5 Sqmm PVC insulated unsheathed copper conductor single core multistranded FRLS (green colour) cable as earth lead drawn in as earth continuity wire in green colour connected to common earth dolly and each terminal/joints fitted with thimble and including connected non metallic rigid PVC conduit not less than 20 mm dia including CI/MS terminal box of required size including 3mm thick plastic laminated top sheet cover fitted with brass screw and cup washer including cutting chases to walls and making good the disturbed surfaces to match with the existing specifications, complete all as specified and directed. Note : In ceiling portion surface conduit wiring shall be carried out.

All as per Srl item No. 130.00 here-in before but for one 5 pin 5 Amps socket outlet on same board with other switch, complete all as specified and directed.

All as per Srl item No. 130.00 here-in before but for metal plug top AC & Geyser point using 4.0 Sqmm FRLS PVC insulated unsheathed copper conductor cable including non metallic rigid PVC concealed conduit not less than 20mm dia medium duty including sunken steel boxes of required size including 3mm thick plastic laminated bakelite sheet cover including 4.00 Sqmm PVC insulated unsheathed copper conductor single core multistranded FRLS (green colour) cable earth wire connecting to earth dolly complete all as specified and directed.

All as per Srl item No. 130.00 here-in before but for one 5 pin 6 Amps socket outlet point on independent board using 1.5 Sqmm FRLS PVC insulated unsheathed copper conductor single core multistranded FRLS cable and 1.5 Sqmm PVC insulated unsheathed copper conductor single core multistranded FRLS (green colour) cable as earth lead drawn in and including connected non metallic rigid PVC conduit of wall thickness 1.8mm including CI/MS terminal box of required size including 3mm thick plastic laminated top sheet cover including cutting chases to walls and making good the disturbed surfaces to match with the existing specifications, complete all as specified and directed. Note:- The unit rate quoted unclude the cost of cutting chases in surface for conduits and fixing sunken boxes and making good the disturbed surfaces to match existing surfaces.

All as per Srl item No. 130.00 here-in before but for 2 in one 5 pin 15/16 Amps socket outlet point on independent board using 2.5 Sqmm FRLS PVC insulated unsheathed copper conductor single core multistranded FRLS cable and 2.5 Sqmm PVC insulated unsheathed copper conductor single core multistranded FRLS (green colour) cable as earth lead drawn in and including connected non metallic rigid PVC conduit of wall thickness 1.8mm including CI/MS terminal box of required size including 3mm thick plastic laminated top sheet cover including cutting chases to walls and making good the disturbed surfaces to match with the existing specifications, complete all as specified and directed. Note:- The unit rate quoted unclude the cost of cutting chases in surface for conduits and fixing sunken boxes and making good the disturbed surfaces to match existing surfaces.

S&F Socket outlet, 6 Pin, 6 Amps, flush type, 230 Volts AC with polycarbonate body, complete all as specified and directed.

S&F Socket outlet, 6 Pin, 5 and 15/16 Amps multipurpose,2 in 1 flush type, 230 Volts AC with polycarbonate body, complete all as specified and directed.

S&F ceiling rose, surface bakelite,2 to 3 terminals, 230 Volts AC with polycarbonate body, complete all as specified and directed.

S&F Switch piano flush button, single pole, one way, 6 Amps, 230 Volts AC with polycarbonate body, complete all as specified and directed.

S&F Switch piano flush button, single pole, one way, 15 Amps, 230 Volts AC with polycarbonate body, complete all as specified and directed.

S&F for 240 volts 10KA 'B' curve miniature circut breaker (MCB) of single poles, current carrying capacity 6 to 16 Amp in the MCB DB Complete with connection testing and commissioning, complete all as specified and directed.

S&F for 240 volts 10KA 'B' curve miniature circut breaker (MCB) of single poles, current carrying capacity 6 to 20 Amp in the MCB DB Complete with connection testing and commissioning, complete all as specified and directed.

S&F for 240 volts 10KA 'B' curve miniature circut breaker (MCB) of single poles, current carrying capacity 5 to 32 Amp in the MCB DB Complete with connection testing and commissioning, complete all as specified and directed.

S&F for 240 volts 10KA 'B' curve miniature circut breaker (MCB) of single poles, current carrying capacity 40 to 63 Amp in the MCB DB Complete with connection testing and commissioning, complete all as specified and directed.

S&F for 240 volts 10KA 'B' curve miniature circut breaker (MCB) of single poles, current carrying capacity upto 32 Amp in the MCB DB Complete with connection testing and commissioning, complete all as specified and directed.

S&F exhaust fan AC single phase 230/240 V of size 150 mm sweep 5 bldes offwhite colour model DX made of polycarbonate body with louvre complete all as specified and directed.

M&L for earthing complete with galvanised steel earth electrode 60cmx60cmx6mm buried directly in ground vertically to depth not less than 2.25m below normal ground level with top edge of the earth plate at a depth not less than 1.5m below ground level connected to and including GI earth lead wire 4 mm dia by means of nuts, bolts, check nuts and washer etc, made of GI and connected to test point and earth dolly all as shown in electrical plate No. 3 SSR Part-I 2009 and specified or indicated including excavation and earthwork in any type of soil PCC (1:3:6) Type C1 in chamber, precast RCC 50 mm thick in cement concrete (1:2:4) type B1, reinforced with welded steel wire fabric or XPM (Weight not less than 4.00 Kg/Square metre) with cast iron frame, funnel with wire mesh, 20mm bore medium grade GI watering pipe, lugs, 15mm bore medium grade GI protection pipe, test point etc. complete all as specified and directed. Note:- (i) Item includes the cost of 7.5 metre GI pipe for protection of earth lead. (ii) Item includes the cost of 7.5 metre GI earth lead.

S&F electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc complete all as specified and directed.

M&L for single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp complete all as spd and directed.

Supply and fixing Sheet metal enclousre for DBs double door single pole and neutral with 200 amps rated bus bar of 4- way, 240 volts complete all as spd and directed.

Supply and laying in trenches or fixed to wall/pole or passing through ducts or pipe, cable LT 1100 volts grade heavy duty, XLPE insulated PVC sheathed, armoured heavy duty electric cable , with aluminium conductor of size 10 Sqmm x 2 core complete all as specified and directed. Note:- Excavation and earth work, sand cushioning, brick cover and protection pipe etc. shall be measured and paid for separately.

M&L for dry clean fine river sand as in sand cushioning to underground cable 23cm thick (8cm before laying & 15cm after laying cable) including punning down of sand layer complete all as specified and directed. Note :- Punned thickness shall only be measured and paid.

M&L for brick protection with sub class 'B' old size brick well burnt laid flat for cable protection abutting each other laid dry with width equal to length of brick complete all as specified and directed.

M&L for supply connecting PVC insulated sheathed FRLS copper multistranded cable of size 1.5 sqmm 3 core for street light/flood light passing through pole/GI pipe/PVC conduit from junction box to street light and connected electrically by thimbles of suitable size junction box busbar incl taking old unsv wire any type and make complete all as specified and directed. Note:- Excavation and earth work, sand cushioning, brick cover and protection pipe etc. shall be measured and paid for separately.

M&L for PCC 1:3:6, type C-1 (using 20mm graded crushed stone aggregate) as in pedestal/coping including necessary weathering and form work etc complete all as specified and directed. Note : Volume of pole/strut shall be deducted for the purpose of payment.

Dismantling of PCC pole or steel pole, any type any size including demolition of concrete in foundation etc. and removing from site.

Taking down carefully street light fitting any type and rating from poles, walls or any other indicated situation / location for reuse of serviceable fittings in another location in cantt area complete after disconnecting electrically from site, complete all as specified and directed.

Supply and erecting in true vertical position prestressed concrete pole of 9.00 metres long,102 mm x 172 mm at top and 102 mm x 279 mm at bottom class 10 including zebra painting to pcc pole up to 1.5m height from base of poles with two coats of synthetic enamel paint Ist quality black & yellow colour alternate strip 30 cm wide and remaing portion with two coats of syntheticenamel paint over a coat of primer, including writing pole number and including demolition of PCC, complete all as specified and directed. Note:-Excavation and earth work and concrete in foundation and pedestal shall be measured and paid for separately.

Supply and fixing as in reapir/replacement of pole mounted street light factory fabricated junction box of size 260mmx160mmx250mm of approved make and of appropriate size made out of 2 mm thick CRCA powder coated sheet , including 63A ,Three Phase four wire having four no.AL Bus Bar including 6A SP MCB. The box should have auto Door Lock facility with magnetic Lock having Sizehaving Size box fixed on pole using necerssary fixing arrangement such as clamps,nut,bolts and washer including taking down existing junction box of any description/type etc complete all as specified and directed.

S&F of lamp holder with lamp holder batten type polycarbonate body with back plate for batten fitting, complete all as specified and directed.

S&F in replacement of lamp holder with lamp holder batten type polycarbonate body with back plate for batten fitting, complete all as specified and directed.

Taking down carefully aluminium / copper point wiring (light / fan / socket or power) complete and making good disturbed surfaces of walls, floors to match with existing specifications and keeping aside serviceable items for reuse within the same bldg and removing UNSV items from site, complete all as specified and directed.

M&L for replacement of Point wiring for one light point / fan point / bell point controlled by one switch with 1.5 Sqmm PVC insulated unsheathed copper conductor single core multistranded FRLS cable and 1.5 Sqmm PVC insulated unsheathed copper conductor single core multistranded FRLS (green colour) cable as earth lead drawn in and including non metallic rigid PVC conduit having wall thicknes 1.8mm including CI/MS terminal box of required size including 3mm thick plastic laminated top sheet cover including cutting chases to walls and making good the disturbed surfaces to match with the existing specifications, complete all as specified and directed. Note:- The unit rate quoted include the cost of cutting chases in surface for conduits and fixing sunken boxes and making good the disturbed surfaces to match existing surfaces.

All as per Srl item No. 161.00 here-in before but for one 5 pin 5 Amps socket outlet on same board with other switch, complete all as specified and directed.

M&L for replacement of point wiring with 1.5 PVC insulated unsheathed copper conductor single core multistranded FRLS (green colour) cable as earth lead drawn in and including connected non metallic rigid PVC conduit of wall thickness 1.8mm including CI/MS terminal box of required size including 3mm thick plastic laminated top sheet cover including cutting chases to walls and making good the disturbed surfaces to match with the existing specifications, complete all as specified and directed. Note:- The unit rate quoted unclude the cost of cutting chases in surface for conduits and fixing sunken boxes and making good the disturbed surfaces to match existing surfaces.

All as per srl item No. 161.00 here-in-before but for one 16 Amps socket outlets point on independent board using 2.5 Sqmm FRLS PVC insulated multistranded copper conductor cable including 2.5 Sqmm FRLS PVC insulated unsheathed multistranded copper conductor cable as earth wire complete all as specified and directed.

All as per srl item No. 161.00 here-in-before but for one 16 Amps socket outlets point on independent board using 4.00 Sqmm FRLS PVC insulated multistranded copper conductor cable including 4.00 Sqmm FRLS PVC insulated unsheathed multistranded copper conductor cable as earth wire complete all as specified and directed.

S&F in replacement Switch piano flush button, single pole, one way, 6 Amps, 230 Volts AC with polycarbonate body, complete all as specified and directed.

S&F in replacement ceiling rose surface bakelite 2 to 3 terminals 230 Volts AC with polycarbonate body, complete all as specified and directed.

S&F in replacement Socket outlet, 6 Pin, 6 Amps, flush type, 230 Volts AC with polycarbonate body, complete all as specified and directed.

S&F in replacement Socket outlet, 6 Pin, 5 and 15/16 Amps multipurpose,2 in 1 flush type, 230 Volts AC with polycarbonate body, complete all as specified and directed.

S&F in replacement Switch piano flush button, single pole, one way, 15 Amps, 230 Volts AC with polycarbonate body, complete all as specified and directed.

S&F "in replacement" VTPN distribution board, double door, TPN 415 Volts 4 way degree of protection IP-65 DBs TPN suitable for MCCB as (for incoming MCCB & outgoing MCBs 415 Volts), including MCCB 415 Volts 63 Amp 16 Ka as incommer and 16 Nos MCB SP 63 Amp cap as outgoing complete with appropriate size copper bus bar for each phase, with 2 Neutral link, fixed flush in wall including chases wall for fixing DB and making good disturbed wall surfaces to match with existing specifications complete all as specified and directed.

M&L "in replacement" for single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amp complete all as spd and directed.

S&F in replacement fan step regulator, step type suitable for 1200/1400mm sweep ceiling fan, hum free, 240 Volts and connecting electrically, complete all as specified and directed.

Supply and fixing Sheet metal enclousre for DBs double door single pole and neutral with 200 amps rated bus bar of 8- way, 240 volts complete all as spd and directed.

Supply and laying in trenches or fixed to wall/pole or passing through ducts or pipe, cable LT 1100 volts grade heavy duty, XLPE insulated PVC sheathed, armoured heavy duty electric cable , with aluminium conductor of size 16 Sqmm x 2 core complete all as specified and directed. Note:- Excavation and earth work, sand cushioning, brick cover and protection pipe etc. shall be measured and paid for separately.

S&F 20 Watt linear 4 feet long LED integrated batten made of epoxy powder coated white, high efficiency, long life LED package in integral module with lumen efficacy > 100 Lm/W and viewing angle of 120° to ensure better uniformity, complete with all accessories prewired and connecting electrically to ceiling rose using PVC insulated and overall sheathed flexible copper conductor cable of size 0.50 Sqmm 2 core all as required at site, complete all as specified and directed.

S&F in replacement 20 Watt linear 4 feet long LED integrated batten made of epoxy powder coated white, high efficiency, long life LED package in integral module with lumen efficacy > 100 Lm/W and viewing angle of 120° to ensure better uniformity, complete with all accessories prewired and connecting electrically to ceiling rose using PVC insulated and overall sheathed flexible copper conductor cable of size 0.50 Sqmm 2 core all as required at site, complete all as specified and directed.

S&F LED 10 watts light fitting mirror type with high output diffuser in unique square > 120 degree wide distribution, 10W 220 Volts AC decorative type with driver holder and LED lamp iincluding connection upto three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F in replacement LED 10 watts light fitting mirror type with high output diffuser in unique square > 120 degree wide distribution, 10W 220 Volts AC decorative type with driver holder and LED lamp iincluding connection upto three core flexible copper conductor cable of suitable size complete all as specified and directed.

S&F of surface mounted LED Bulk Head luminaires 9/10 watts with ABS body & polycarbonate diffuser available in CCT 6000K IP 54 complete all as specified and directed.

S&F in replacement of surface mounted LED Bulk Head luminaires 9/10 watts with ABS body & polycarbonate diffuser available in CCT 6000K IP 54 complete all as specified and directed.

S & F of decorative wall bracket light white in colour made up of poly carbonate suitable for and including 9 watts retrofit LED lamp complete all as specified and directed.

S&F in replacement of LED bulb 12 watt 230 volt complete all as specified and directed.

S&F in replacement of existing unsv recess/suspended slim LED panel light with powder coated rim 36 watts of size 2'x2' high efficency designer recessed mirror optic luminary with ceiling cut out size 36 watt including LED lamps complete including connecting electrically to ceiling rose using cord flexible 3 core PVC insulated over all sheathed with flexible copper conductor of size 0.75mm complete all as specified and directed.

S&F in replacement for bldg street light fitting with LED 30 Watt energy saving LED Building security Light luminaire. IP 66, AC 230 volts, LED building security light shall be made up of Pressure Die Cast aluminum housing with black epoxy polyester powder coating for long life and toughened glass visor fitted in frame, secondry optical lens for superior light distribution efficiency 100Lm/W making connections with street light/ building security light box or OH line using PVC insulated and sheathed three core multi stranded copper conductor cable of size 1.5 Sqmm including suitable size of brackets and light grade pipe for maintaining of fittings complete all as specified and directed.

S&F for bldg street light fitting with LED 25 Watt energy saving LED Building security Light luminaire. IP 66, AC 230 volts, LED building security light shall be made up of Pressure Die Cast aluminum housing with black epoxy polyester powder coating for long life and toughened glass visor fitted in frame, secondry optical lens for superior light distribution efficiency 100Lm/W making connections with street light/ building security light box or OH line using PVC insulated and sheathed three core multi stranded copper conductor cable of size 1.5 Sqmm including suitable size of brackets and light grade pipe for maintaining of fittings complete all as specified and directed.

Note for srl item No 177 to 187 1. Driver shall be potted anti-vibration types. 2. LM-79 and LM-80 test report with 1 Lakh burning hours LED life from NABL lab shall be provided. 3. CRI (Colour Rendering Index) of fixture shall be > 70. 4. CCT (Colour Co-related Temperature of fixture shall be 5700K + 300 K. 5. System Lumen Efficacy shall be > 100 Lm/W. 6. 10 KV separate Surge Protection shall be provided as a part of fitting. 7. 2 years guarantee shall be provided by contractor supported by OEM covering all parts of luminaire. 8. Lenses shall be Modular Type. 9. PCB used shall be MC PCB type. 10. The defect liability period of LED light shall be 05 years from the certified date of completion & the contractor shall replace/repair the defective fitting within 07 days after handing over to contractor for replacement/repair. 11. CA No. shall be written on each fitting before installation. 12. The name of manufacturer to be embossed on the fitting. 13. The fittings shall have arrangement so that maintenance required, if any can be carried out from Top cover.

Supply install and testing hi wall split Air conditioner 1.5 Ton cap, 5 star rating, all weather, having indoor & outdoor units complete with cordless remote control unit and with in built air ioniser and Plasma filter for better indoor air quality, complete all as specified and directed.

S&F Voltage stabilizer for automatic operation, single phase, naturally air cooled indoor type & designed for input variation between 165 V to 270 V with output voltage stablized at 230 V with accuracy of ± 2% having low & high voltage cut off protection and initial time delay feature, current rating cap 12 Amp min suitable for 1.5 Ton split AC complete all as specified and directed.

S&F Sheet metal enclosure (industrial type) single pole and neutral enclosure with a two pin and earth plug and socket complete with including MCB 16/20 Amp MCB double pole 240 volts complete all as specified and directed.

Supply and laying in trenches or fixed to wall/pole or passing through ducts or pipe, cable LT 1100 volts grade heavy duty, XLPE insulated PVC sheathed, armoured heavy duty electric cable , with aluminium conductor of size 16 Sqmm x 4 core complete all as specified and directed. Note:- Excavation and earth work, sand cushioning, brick cover and protection pipe etc. shall be measured and paid for separately.

Supply and fixing Sheet metal enclousre for MCB DBs when MCB to be used TPN 4 way double door 415 volt including 1xTPN 63 Amps 10 KA incomer and four SPN 32 Amps as outgoing complete all as spd and directed.

jagdish sons

M/S NARESH KUMAR SHARMA

Ms Tarsem Kumar Sharma

Bidder Name

jagdish sons

Ms Tarsem Kumar Sharma

AV ENTERPRISES

M/S NARESH KUMAR SHARMA