DAY TO DAY/PETTY REPAIR TO MISC B/R ITEMS IN VARIOUS BLDGS AT OTM AND MD ACCN AT NAD TROMBAY AND REPAIRS/CLEANING OF SEWAGE LINE, MANHOLE AND SEPTIC TANKS AT NAD UNDER GE (NW) MANKHURD

Amount

Petty repairs to wooden joinery works such as Resecuring or easing and adjusting of doors, windows kitchen cabinets in any size, refixing hinges etc by providing glue nails and screws to the satisfaction of user and rectifying other misc minor carpentary works assigned by the Engineer In charge. (Note : Some of the items of Builders Hardware will be supplied by MES as free for fixing and other minor repair items (screw, Nails etc) shall be inclusive with the rate quatated by the contractor)

Petty repairs to plumbing/internal water supply works such as repair to leaking bib taps, pillar taps, mixers stop cocks by tightening and providing spindle,washer repairs to float valves, low leveled cistern to the satisfaction of user as assigned by the Engineer In Charge. (Note : Some of the items of Plumbing Items will be supplied by MES as free for fixing and other minor repair.items (screw, Nails etc) shall be inclusive with the rate quatated by the contractor) Note item No 1 and 2 : (a) Rep of contractor will collect details of complint from departmant. The contractor will be alloted complaint on daily basis and sufficient resources will be deployed by him/her for completion of day to day comaplaint within 24 Hrs from the time of reporting. Any delay beyond above mentioned time limit suitable penalties as mentioned in relavant clause of Contract. (b) A detailed log of complaints with completion/ non-completion remarks from users/MES will be maintained by the contractor and same will be updated on daily basis in consulatation with Engr-in-Charge or JE detailed by him. (c) The contractor will make suitable arrangment for emergent complaints and will notify auth rep/Engr-in-Charge about extraordinary circumstances for probable non-completion or delay in rectification of complaints beyond state time limit set for disposal of complaint. In case of any dispute the decision of accepting officer will be final and binding in this regard. (d) The quoted rated deems to be inclusive of transportation and other expenses required for the resource deployment at the complaint site around scattered Naval Depot. (e) The contractor will maintain suitable inventories and range of spares required to meet the complaints as same will be reviewed peridically by Engr-in-charge to streamline complaints disposal system.

Taking down cement plaster on brick or concrete surfaces etc, including raking out joints, hacking for key, scrubbing own with water, etc complete all as specified and directed.

M & L for rendering 15 mm thick in CM 1:6 on brick walls or concrete surfaces finished the surfaces even & smooth incl 1mm thick sagol finish including preparation of old surfaces in patches for repairs at any places inside the bldg etc complete all as specified and directed.

M & L for rendering 20 mm thick in CM 1:4 on brick walls or concrete surfaceslaid in two layers, Ist layer 15mm thick and finishing layer 5mm thick mixed with integral water proofing compound @ 2% by weight of cement content of finishing layer finished fair and even without using extra cement,additonal thickness provided as floating/setting coat, including all necessary scaffolding/staging as required including preparation of old surfaces in patches for repairs at any places outside the bldg etc complete all as specified and directed.

M & L for rendering 05 mm thick in CM 1:3 on ceiling , soffit of staricase surfaces finished even and smooth with 1mm thick sagol finish, including preparation of old surfaces in patches for repairs at any places inside the bldg etc complete all as specified and directed.

M & L preparing new surfaces of walls applying two coat of oil bound distemper over one coat of primer etc complete all as specified and directed.

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10sqm over new surfaces etc complete all as specified and directed.

M& L for preparation of newly plastered surface and applying three coat of white wash on ceilings etc complete all as specified and directed.

Taking down aluminum door shutter carefully and refixing the same in position replacing rubber bead, worn-out door closer mortice lock and replacing existing broken aluminium section / glass / wire cloth / Bakelite sheet, if any and making door shutter serviceable, for work etc complete all as specified and directed. Note - Aluminum Section / Glass / wire cloth / Bakelite sheet, shall be measured and paid separately as supply only. Fixing element of these items shall be deemed to be included in quoted rate.

Taking down aluminum window shutter carefully and refixing the same in position replacing rubber bead, worn-out handles and replacing existing broken Aluminum section / glass/wire cloth/backlite sheet, if any, and making window shutter serviceable etc complete all as specified and directed. Note - Aluminum section / Glass / wire cloth / Bakelite sheet, handle etc shall be measured and paid separately as supply only. Fixing by element of these items shall be deemed to be included in quoted rate.

Taking down chowkhat or frame (without taking off shutter from the frame) not exceeding 1.5 Square Metre each , removing from the site including cutting holes required for taking out existing hold fast etc complete all as specified and directed.

Taking down chowkat or frame with shutter (without taking off shutter from the frames), exc 1.50 sqm but not exc 4.0 sqm each etc complete all as specified and directed.

Taking down shutters of any description, not exc 1 Sqm each etc complete all as specified and directed.

Taking down shutters of any description, exc 1 Sqm and n.exc 2 sqm each etc complete all as specified and directed.

M&L for IInd class Hard wood (Sal) plain, solid, straight chowkats and frames, wrought, framed, rebated on the solid, rounded or chamfered, put together with glue, pinned at joint etc complete all as specified and directed.

S & F,IInd class hardwood 35mm thick Plain, framed,panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats etc complete all as specified and directed.

S & F 2nd class hardwood, glazed and skelton shutter, 35mm thick, open rebated and prepared to receive glass, gauze etc, divided into square with plain, chamfered or rounded mitered and rebated sash bars, edges of framing plane, chamfered or rounded, fitted with cut and mitered bead for securing glass, gauze etc, size of member of shutters as specified in SSR Part -I, section 8, class 8.24(a) (Door shutter), supplied and fitted to chowkats etc complete all as specified and directed.

S & F , in repairs, IInd class Hard wood plain fillets squares, rectangular or triangular in section, wrought, secured with screws, sectional area exc 13 Sqcm and not exc 25 Sqcm etc complete all as specified and directed.

M&L for 18/19mm thick pre laminated particle board interior grade, prelaminated both sides woth decirative choice olaminations, fixed with screws to timber frame work or any other position etc complete all as specified and directed.

S&F for Solid PVC door frame of size 50mm x 47 mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying & fixing in opening as per spcification & drawing etc, complete all as specified and as directed.

S&F for plain sheet PVC door shutter , 28 to 30 mm thick (stiles), with 2,4 or 6 raised panel design with 2mm th. Moulded PVC sheet on the front face & 2mm plain coour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing with wood free EPS etc, complete all as specified and as directed.

M & L for Machine cut cudappah stoneslab 18-20mm thick over cementscreed base, laid and mixedwith pigment to match the shade of the slab window cills and jambs to full thickness of wall fixed in steps over cement screed bed 10mm thick in CM 1:4 and jointed with grey cement paste and slurry including rubbing and polishing etc complete all as specified and directed.

S&F standard aluminium section powder coated (minimum thickness of powder coating shall be 50 micron and colour shall be as approved by GE ) as in frame, shutters for doors, window / ventilators, fixed / openable / sliding or in any pattern, cut to size, jointed with cadmium plated steel screws, including rubber beading or gaskets for fixing glass, provision of hinges, screws, plugs, handle, lock, roller, Nylon ball bearing etc complete all as specified and directed. (Aluminium section shall be of make Jindal/Hindalco/ Indalco) Note:- Weight of Aluminium sections as per actual or as per IS or as per manufacturer, whichever is less, shall only be considered for payment. Cost of other items / accessories required for entire completion of the work shall be deemed to be included in the quoted rate. However glass panes, shall be measured and paid separately as supply only under respective item.

S&F aluminum anodised grill DG- 202 ( 10 mm x 5.2mm ) of Deco grill or equivalent fixed with 'F' section size not less than 20.60 x 15.20 x 1.5mm thick of approved make etc complete all as specified and directed. Note : (i) Make shall be of M/s Decogrille of M/s Associated Groups or equivalent as approved by the GE. (ii) Minimum thickness of anodizing shall be 15 microns.

S&F Bands, straps, supports or stays for rainwater, ventilating pipes,including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges large hasps and staples; chains; hand made sliding bolts; clamps;hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 etc complete all as specified and directed.

M&L for providing cement concrete type C1, 1:3:6, using 20mm graded stone aggregate as in bed block for hold fast, coping etc including necessary form work etc complete all as specified and directed.

M&L for preparing surfaces of wood and wood based materials steel and iron work, new or old of any description and girth, not otherwise described and treating ends of posts, back of chowkat etc with tar or coal tar black paint, area tarred exc 0.10 sqm but not exc 0.50 sqm each etc complete all as specified and directed.

Ditto all as per item No 42 herein above but treating small articles such as stopper, covers, hold fast ends, posts back etc, not exc 0.10 sqm each etc complete all as specified and directed.

S&F for 4.0mm thick sheet glass ordinary quality and glazing with oil putty in steel windows and in aluminium sliding shutters square not exc 0.5 Sqm in each pane etc complete all as specified and directed.

S & F in repairs floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring of length 140mm fixed in floor etc complete all as specified and directed.

S &F, in repairs, aluminium alloy wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with in aluminium sliding shutters, doors etc complete all as specified and directed.

Supply and fix aluminium alloy anodised sliding door bolt with hasp and staple(bolt type) and fixing clips of sheet, cast or extruded section and fixing bolt and sliding bolt of extruded section of size 250 mm fixed at any position etc complete all as specified and directed.

S&F in stainless steel butt hinges, 100mm, medium weight etc complete all as specified and directed.

S&F in extruded aluminium alloy handles, fabricated type of size 150mm in any position etc complete all as specified and directed.

S&F in aluminium, anodised, barrel tower bolts of extruded section of size 150mm etc complete all as specified and directed.

S&F in mortice lock vertical type 75mm 04 lever brass for aluminium door with complete fittings etc complete all as specified and directed.

S&F in Godrej night latch 4 lever for entrance door with fittings etc complete all as specified and directed.

S&F CI floor trap 75mm dia outlet, with CP grating including jointing to waste pipe, fixed in cement concrete type B1 (1:2:4) & taking down old trap etc complete all as specified and directed.

S&F CI floor trap 100mm dia outlet, with CP grating including jointing to waste pipe, fixed in cement concrete type B1 (1:2:4) & including taking down old trap etc complete all as specified and directed.

S&F in repair for CP stop cock 15mm bore fancy type chromium plated.with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed etc complete all as specified and directed.

S&F stainless steel kitchen plate rack etc complete all as specified and directed . Make:Prayag polymers Pvt Ltd or equivalent

S&F stainles steel sink with drainage board , 1 mm thick sheet of steel grade AISI 304 for kitchen or laboratory, with plug, waste pipe, washers including CI cantilever bracket, connecting union etc., overall size 915 x 460 mm with bowl size 410 mm x 330 mm x 160 mm including supply and fixing bib tap CP with long body screwed for iron pipe complete etc complete all as specified and directed. Make : Nirali, Bule star ISI marked.

S&F in repair low density polyethene pipes (LDPE) 40mm of pressure rating 6 Kg/cm2 fixed to walls or laid in floors etc complete all as specified and directed.

Taking up or down steel tubing and connection, removing clear off site after credit for the same is recovered by the dept., bore of pipe 15mm etc complete all as specified and directed.

Taking up or down steel tubing and connection, removing clear off site after credit for the same is recovered by the dept., bore of pipe 20mm etc complete all as specified and directed.

S&F 15mm bore U- PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc. with all fittings etc complete all as specified and directed.

All as per item No 47.00 above but 20 mm bore etc complete all as specified and directed.

S&F in repair for gun metal globe or gate valves with iron wheel head , screwed both ends for iron pipe & fixed of size 20mm bore etc complete all as specified and directed.

Dismantling floor, hearth or wall tiling and stone slabs including cement mortar bedding (but not backing), removing rubbish off the premises outside MD Land etc complete all as specified and directed.

M&L for coloured Non-skid ceramic tiles 7 to 8mm thick (square/ rectangular) of approved size, area of each tile exceeding 0.11 Sqm but not exceeding 0.16 Sqm in floors etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, over and including 15mm thick cement mortar screed bed in CM 1:6 etc, complete all as specified and directed.

M&L for coloured Non-skid ceramic tiles 7 to 8mm thick (square/ rectangular) of approved size, area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm in floors etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, over and including 15mm thick cement mortar screed bed in CM 1:6 etc etc complete all as specified and directed.

M&L for coloured 300x200x7mm thick glazed ceramic tiles on vertical surfaces such as skirting,dado and risers to steps etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, over and including 10mm thick cement mortar backing coat in CM 1:4 etc complete all as specified and directed.

Labour for cleaning /cleaning of blockage of manholes, gully traps, floor traps, vertical soils/ waste pipe of different dia and sewage lines in the area of the NAD (Colony) and NAD (Depot) under GE (NW) Mankhurd Note: a) The labour (02 nos) will report daily at 0845 hrs on all working days including Sundays and holidays at online complaint cell centre and attend complaints till 1645 hrs given by Engr -In- Charge . Complaints needs to be cleared within 24 hrs after receiving the complaints . The contractor will deploy requisite labour and supply all T&P ( mechanical Iron rods, knot ropes , bamboo etc) scaffolding ladders any other materials required to clear the blockages at the site without any extra cost .Labour for cleaning of sludge from sewage lines (any dia) to manhole is included in quoted rates. In case any labour does not report to Engineer In Charge for the whole day or found missing more than half an hour on any day, Panel recovery @ RS.860/- per head per day shall be made proportionally from contractor's dues. b) The above item includes conveyance cost of labour with their tools to travel from pocket to pocket to attend complaints including removal of sludge from the site outside MOD land to a distance not exc 5km (The department shall not be liable to provide any kind/form of transportation to the labour). (c) Registers of labour attendance and complaints shall be maintained by contractor at their own cost,which shall be kept in the custody of MES Department(complaint cell) duly signed by contractor's representative ,JE(civil) and Engineer in charge.

Opening cover of septic tank, of size 5 - 10 Sqm area dewatering and taking out night sludge etc from septic tank and removing sludge outside MD land and cleaning the septic tank as per BMC rules and placing the cover in original position etc complete all as specified and directed. Note: All T&P and transportation for carrying sludge including labour shall be provided by the contractor at their own cost.

Opening cover of septic tank, of size exc 10 - 15 Sqm area dewatering and taking out night sludge etc from septic tank and removing sludge outside MD land and cleaning the septic tank as per BMC rules and placing the cover in original position etc complete all as specified and directed. Note: All T&P and transportation for carrying sludge including labour shall be provided by the contractor at their own cost.

Opening cover of septic tank, of size exc 20 Sqm area dewatering and taking out night sludge etc from septic tank and removing sludge outside MD land and cleaning the septic tank as per BMC rules and placing the cover in original position etc complete all as specified and directed. Note: All T&P and transportation for carrying sludge including labour shall be provided by the contractor at their own cost.

M & L Septic tank for 10 users RCC precast hume pipe culvert, designed to carry sewage and sullage water , excavation in any type of soil, PCC 1:4:8 below foundation, vent shaft, connection etc complete all as specified and directed.

M & L for filled with brick bats of 1.2M dia X 1.5 M effective depth for soakage wells excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonary with top ring of M25 concrete including intercepting chamber and screen chamber made of brick masonary in CM, RCC cover slab in M25/SFRC cover interconnecting pipes of RCC/DWC etc complete all as specified and directed.

Demolition of brick work or stone/boulder, masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but exceeding ashlar facing and pre-cast concrete articles etc complete all as specified and directed.

Demolition of cement concrete ,un-reinforced in ground floors and paving not exceeding 15 centimetre thickness, below or above ground level etc complete all as specified and directed.

Demolition of cement concrete ,(reinforced) of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) etc complete all as specified and directed.

Demolition and breaking up drain pipes (slat glazed ware, AC or reinforced concrete) set in cement mortar , in 200 mm internal dia and taking out of trenches if required etc complete all as specified and directed.

All as per item No 63.00 above, but 150mm dia pipe etc complete all as specified and directed.

Demolition /Dismantling of 200mm dia cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches if required

All as per item No 65.00 herein above but 300 mm dia etc complete all as specified and directed.

M&L Salt Glazed Stone Ware drain pipe, grade ‘A’ 200 mm bore laid in trenches and jointed etc complete all as specified and directed. Note : Excavation and earth work shall be measured and paid separately.

All as per item No 67.00 above but 150mm dia etc complete all as specified and directed.

M&L reinforced concrete pipes, class NP - 2, 300 mm bore, laid in trenches and jointed complete with collars etc complete all as specified and directed.

M&L reinforced concrete pipes, class NP - 2, 250 mm bore, laid and jointed complete with collars etc complete all as specified and directed.

M&L for 200 mm thick Concrete bed to drain pipes in cement concrete 1:3:6 type C-2 using 20 mm graded stone aggregate including packing under and haunching against the sides of pipes after they are laid and tested for 200 mm bore pipe etc complete all as specified and directed.

M&L for 150 mm thick Concrete bed to drain pipes in cement concrete 1:3:6 type C-2 using 20 mm graded stone aggregate including packing under and haunching against the sides of pipes after they are laid and tested for 150 mm bore pipe etc complete all as specified and directed.

Excavation in trenches not exceeding 1.50 metre wide and not exceeding 1.50 metre depth for foundation, manhole etc not exc 10 Sqm on plan and not exc 1.5 metre in depth including getting out in soft/loose soil etc complete all as specified and directed.

All as per Item No 73.00 herein above but additional 1.5m depth etc complete all as specified and directed.

Returning, filling in including spreading, leveling watering and well ramming in layers not exceeding 25 centimetre in soft/loose soil etc complete all as specified and directed.

Removing excavated surplus soil/material not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point etc complete all as specified and directed.

M&L Plain Cement concrete 1:3:6 type C-1, using 20 mm graded stone aggregate as in foundation filling and mass concrete etc complete all as specified and directed.

M&L Plain cement concrete 1:3:6 type C-2 using 20 mm graded stone aggregate as in surface channel, drain etc complete all as specified and directed.

All as per Serial Item No 78.00 herein above but PCC 1:2:4 Type B-1 using 20mm graded stone aggregate as in benching, coping including necessary form work etc complete all as specified and directed.

M&L Brick work with sub class ‘B’ bricks, straight or curved on plan exceeding 6 metre means radius built in cement mortar 1:4 etc complete all as specified and directed.

M&L for walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in CM 1:6 etc complete all as specified and directed.

Extra over stone walling for Hammer dressing to face stones with maximum depression on fair face from straight edge held against the dressed surface not exceeding 20 mm for granite or trap stone of face beds & joints as specified of random rubble walling uncoursed or brought upto course etc complete all as specified and directed. Note :- Hidden portion of masonry shall not be hammer dressed

Hammer dressing to face stones with maximum depression on fair face from straight edge held against the dressed surface not exceeding 40 mm for granite or trap stone of face beds & joints as specified of random rubble walling uncoursed or brought upto course etc complete all as specified and directed. Note :- Hidden portion of masonry shall not be hammer dressed

M & L for rendering 15 mm thick on fair faces of brick work or concrete surface in cement mortar 1:4 mixed with WPC as per manufacturer's instruction and finished the surfaces even and smooth without using extra cement etc complete all as specified and directed. Note:- WPC will be measured and paid for separately.

M& L for raised pointing to random rubble masonry uncoursed or brought upto courses in CM 1:4 etc complete all as specified and directed.

M&L 15 mm thick cement plaster in CM 1:6 on stone masonry surfaces or surface other than fair faces of brick work or on one side of lathing etc complete all as specified and directed.

Supply only integral water proofing compound as per latest IS specification etc complete all as specified and directed.

M&L Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200m thick (Horizontal or sloping) rough finished flat concrete surfaces etc complete all as specified and directed.

M&L fo fair finished flat form work to edges of concrete flats, treads, breaks infloors, window cills, concrete railings, openings in concrete walls floor and roofs not exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or slopping and similar work etc complete all as specified and directed.

M&L for reinforced cement concrete type B-1 1:2:4 (20mm graded aggregate) slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like etc complete all as specified and directed.

M&L Pre-cast cement concrete cover slab for manhole and drain cover in plain cement concrete 1:2:4 type B-1, (using 20 mm graded stone aggregate) set in cement mortar 1:4 with plain faces etc complete all as specified and directed.

Mild steel deformed/TMT bars 10 mm dia, cut to length, bent to shape required including cranking bending spirally for hoping for columns, hooking ends and binding with mild steel wire, annealed not less than 0.9 mm dia or securing with clips etc complete all as specified and directed.

Cutting into existing manhole, 150 mm bore pipe, for connecting new drains making good to pipe and removing cutting out existing benching for and forming branch channel in cement concrete 1:2:4 type B-1 using 20 mm graded stone aggregates, smooth finish and re-forming benching etc complete all as specified and directed.

All as per Item No 93.00 above but for 225 mm bore pipe etc complete all as specified and directed.

Cleaning of SGSW pipe lines 100 mm to 150mm bore pipe and removing the blockage by means of rodding with and including bamboo splits/flexible iron wire or concrete malacces rods from manhole to manhole, through pipes from trap to manhole, rendering the system clear and flushing the delogged line with sufficient quantity of water and removing sludge/waste material etc. to a distance n. exc 50 M and burrying in pits and re-filling the same etc complete all as specified and directed. Note :- The cost for excavation and earth work for pits is deemed to be included in the unit rate.

All as per Item No 95.00 herein above but line of 200 mm bore pipe etc complete all as specified and directed.

All as per Item No 95.00 herein above but line of 300 mm bore pipe etc complete all as specified and directed.

Cleaning of blocked Soil Pipe Vertical stack 100/110 mm dia by opening inspection eye door of bend/ branch pieces, rodding till smooth flow and refixing of door after cleaning including necessary scaffolding etc complete all as specified and directed.

Cleaning manhole of size n.exc 1.50 Sqm by taking out sludge in semi liquid/solid stage (incl. all water etc) from inside of manhole of depth not exceeding 1.5 m and removing the sludge to a distance not exceeding 50m depositing in trenches including supply and sprinkling bleaching powder and covering sludge with earth to a thickness not less than 30 cm including all earth work, returning filling, removal of surplus soil & necessary temporary cleaning etc complete all as specified and directed.

All as per item 99.00 here-in-before but depth exceeding 1.5m but n.exc 3m deep etc complete all as specified and directed.

S & F for precast Heavy duty circular manhole cover of size 750 X 450 mm fixed in position with frame work and necessary cement work complete including taking down old one etc complete all as specified and directed.

All as per item No 101 above, but rectanglular in shape of size 600 x 450mm etc complete all as specified and directed. Note : A sum of Rs 20,915.00 towards sch of credit shall be deducted to arrive the contract sum.

GAJANAN SALES CORPORATION

H R ENGINEERS

mp construction co

Parmatma Enterprises

Atharva Enterprises

sahajanand const co.

Joy builders