Construction of Common Kitchen for solar steam cooking system at main campus Nauni, Solan (SH - Site Development, Building portion, Water supply and Sanitary Installation).

Amount

Excavation in foundation trenches etc. in all kinds of soil such as pick work, jumper work including chiseling / wedging etc. with all lifts stacking the excavated soil not more than 3 metres clear from the edge of excavation and then returning the stacked soil in 15 cm layers, when required into plinth sides of foundation etc. consolidating each deposited layer by ramming and watering and then disposing of all surplus excavated earth as directed with all leads and lifts of material as directed by the Engineer-in-Charge.

Excavation in all kinds of earth work such as pick work, jumper work, including chiseling/wedging etc. and disposal of all excavated earth upto all leads, lifts and disposed earth to be leveled and neatly dressed complete in all respect as per satisfaction of Engineer-in-charge.

Filling in plinth with sand under floors including watering ramming consolidating and dressing complete including all leads and lifts of material as directed by the Engineer-in-Charge.

Providing Form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden battens and ballies height of propping and centring below supporting floor to ceiling not exceeding 4 metres and removal of the same for insitu-reinforced concrete complete and plain concrete work including all leads and lifts of material as directed by the Engineer-in-Charge.

a) Foundation footings, bases of column etc. and mass concrete.

b) Beams, cantilever, girders and lintel : 1. Sides and soffits of beams, beam haunchings, cantilevers, girders bressurmers and lintels not exceeding 1 metre in depth

c) Flat surface such as soffits of suspended floors, roofs landing and the like Floor etc. upto 200mm in thickness.

d) Stair cases with sloping or stepped soffits including risers and stringers excluding landings.

Providing and laying cement concrete 1:6:12 (one cement: six sand and twelve graded stone crushed aggregate 40mm (forty milimetre nominal size) curing complete excluding cost of form work in foundation and plinth in all leads and lifts of material as directed by the Engineer-in-Charge.

Providing and laying cement concrete 1:8:16 (one cement : eight sand : sixteen graded stone crushed aggregate 20mm nominal size)and curing complete on slab and floor excluding the cost of form work screed laid under flooring complete in all respect as per satisfaction of Engineer-in-charge.

Providing and laying damp proof course to horizontal / vertical surfaces with cement mortar 1:2 (one cement : two sand) and curing complete in all respect as per satisfaction of Engineer-in-charge. a) 20mm thick

Applying a coat of hot bitumen (maxphalt 80/100) or equivalent using 1.70 kg. per square metre on damp course after cleaning the surface with piece of cloth lightly soaked in kerosene oil including all leads and lifts of material as directed by the Engineer-in-charge.

Providing and laying cement concrete work with concrete mixer and vibrator mix 1:1.5:3 (one cement one and half sand: three graded stone aggregate crushed aggregate 20mm (twenty millimetre nominal size) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in all leads and lifts as directed by the Engineer-in-charge.

a) Foundations, footings bases of column and the like and mass concrete.

b) Suspended floor roofs, landings and shelves and their supports balconies, beams girders, bressurmers and cantilevers upto all floor level.

c) Stair cases (except spiral stair cases) excluding landings but including preparing of the surface and finishing of nosing upto all floor level.

Providing and laying upto all floor level reinforced cement concrete 1:3:6 (one cement : 3 sand : 6 graded stone aggregate 20mm nominal size) to give a smooth and even surface centering and shuttering etc. but excluding cost of reinforcement complete in all respect as per satisfaction of Engineer-in-charge. a) Moulding as in cornices window sills etc. not exceeding 15cm in girth

Providing TMT steel reinforcement for R.C.C. work including bending binding and placing in position complete upto all floor level including all leads and lifts of material as directed by the Engineer-in-Charge.

2nd class brick work using common burnt clay building bricks in foundation and plinth in cement mortar 1:6 (one cement : six sand) including all leads and lifts of material as directed by the Engineer-in-Charge.

2nd class brick work using common burnt clay building bricks in superstructure in cement mortar 1:6 (one cement: six sand) including all leads and lifts of material as directed by the Engineer-in-Charge.

2nd class half brick masonry using common burnt clay building brick in superstructure in cement mortar 1:4 (one cement: four sand) including all leads and lifts of material as directed by the Engineer-in-Charge.

Providing and fixing anodized aluminium and dyed to required shade work for doors, windows, ventilators and partitions with extruded built up standard tubular and other sections of approved make conforming to IS-733 and IS-1285 anodized transparent or dyed to required shade according to IS-1868 (minimum anodic coating of grade AC-15). Fixed with rawl plug and screws or with fixing clips or with expansion hold fasteners including necessary filling up of gaps at junctions at top, bottom and sides with required PVC/neoprene felt etc. Aluminium sections shall be smooth, rust free, wherever required including cleat angles, aluminium snap beading for glazing/paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the direction of Engineer-in-Charge (Jindal / Hindalco make).

a) For doors, windows ventilators & glazed partition frames.

b) For shutters of doors, windows and ventilators including providing and fixing hinges pivots and making provision for fixing of fittings. Where ever required including the cost of PVC/neoprene gasket required (fittings and glazing / paneling shall be paid for separately.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partition etc. with PVC/ neoprene gasket etc. complete as per architectural drawing and the directions of Engineer-in-Charge (cost of aluminium snap beading shall be paid in basic item).

a). Glass panes of 4mm thickness (weight not less than 10.00 Kg/Sqm).

b). Glass panes of 5.5mm thickness (weight not less than 13.75 Kg/Sqm).

Providing and fixing anodized aluminium sliding door bolt anodized transparent or dyed to required colour and shade with bolts and nuts screws etc. complete including all leads and lifts as directed by the Engineer-in-Charge.

a) 300 x 16mm (three hundred into sixteen milimetre)

b) 250 x 16mm (two hundred fifty into sixteen milimetre).

Providing and fixing aluminium tower bolts (barrel type) anodized transparent or dyed to required shade and colour with screws etc. complete including all leads lifts of material as directed by the Engineer-in-Charge.

a). 200x10mm (two hundred into ten milimetre)

b). 150x16mm (one hundred fifty into ten milimetre)

c). 100x10mm (one hundred into ten milimetre)

Providing and fixing aluminium handles anodized transparent or dyed to required colour and shade with necessary screws etc. complete including all leads and lifts of material as directed by the Engineer-in- Charge.

a) 125mm (one hundred twenty five milimetre)

b) 100mm (one hundred milimetre)

Providing and fixing Aluminium anodized powder coated pattern to existing window /ventilator with 80mmx80mm panels holes with 8mm dia aluminium rod in window and ventilators including fixing with aluminum screws or bolts and nuts complete in aluminum channels base frames etc. complete in all respect as per satisfaction of Engineer-in-charge.

Kota stone slab flooring 20mm (average) thick base of cement mortar 1:4 (one cement : four sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete as directed by the Engineer-in-Charge. a)25mm (twenty milimetre) thick

Kota stone slab 25mm (twenty five milimetre) thick in risers of steps skirting, dado and pillars laid on 12mm (average) thick cement mortar 1:3 (one cement: three sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete as directed by the Engineer-in-Charge.

Providing & fixing 10mm thick antiskid water proof stain & impact resistant heavy duty vitrified tiles (Premium Kazaria / Nitco/ Johnson make) 600x600mm and 10mm thick manufactured of approved shade and colour in floorings, treads of steps and landing laid on a bed of 12mm thick cement mortar 1:3 (One cement : three sand) jointed with cement slurry mixed with pigment to match the shade of tiles as required complete in all respect as per satisfaction of Engineer-in-charge.

White / coloured glazed jointlesss tiles 8mm (eight milimetre) thick in skirting risers of steps and dado 12mm (twelve milimetre) thick cement plaster 1:3 (one cement : three sand) and jointed with white cement slurry including all leads and lifts of material as directed by the Engineer-in-Charge (Nitco/ Johnson / Kazaria make 1st quality).

Providing & fixing 0.60mm (point sixty milimetre) thick prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polister of 5 micron over 5 microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia with prepainted limpet and rubber washers complete with all accessories as required as per the direction /satisfaction of Engineer-in-charge(Tata/Jindal Make).

Providing & fixing 0.60mm (point sixty milimetre) thick and 60cm wide ridges or hips prepainted steel sheet in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polister of 5 micron over 5 microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm dia & prepainted GI limpet and bitumen washers complete with all accessories as required as per the direction / satisfaction of Engineer-in-charge(Tata/Jindal Make).

Steel work welded in built up sections trusses and framed work including cuttings, hoisting, fixing in position and applying a priming coat of red lead paint including all leads and lifts of material as directed by the Engineer-in-Charge. a)In beams, joists, channels angles, tees, flats with connecting plates or angles as cleats in main and cross beams, hip and jack rafters, purlins connected to common rafter and the like.

a)In beams, joists, channels angles, tees, flats with connecting plates or angles as cleats in main and cross beams, hip and jack rafters, purlins connected to common rafter and the like.

b) In grating framed guard bars, ladders, railing, brackets and similar work.

Providing and fixing in position collapsible steel shutter with vertical channels 20x10x2mm and braced with flat iron diagonals 20x5mm size with top and bottom rails of T. iron 40x40x6mm with 38mm dia steel pulley complete with bolts and nuts locking arrangement stoppers, handles including applying a priming coat of red lead paint complete in all respect as per satisfaction of Engineer-in-charge.

Painting two coat (excluding priming coat) on new steel and other matter surfaces with enamel paint brushing to give an even shade including cleaning the surface of all dirt, dust and other foreign matter including all leads and lifts of material as directed by the Engineer-in-Charge. a) Enamel paint other than white.

Wall painting (two coats) with acrylic emulsion paint of approved brand and manufacture for interior grade on undecorated concrete / stone / plastered wall surfaces to give an even shade including thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth including applying of putty a required for metling the surface complete in all respect as per satisfaction of Engineer-in-charge.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equarlied on undecorated wall surfaces (two coats) to give an even shade and final finish after thoroughly cleaning the surface to remove all dirt, dust & other foreign matter etc. including sand paper smooth complete in all respect as per satisfaction of Engineer-in-charge.

6mm (six milimetre) cement plaster to ceiling in cement mortar 1:3 (one cement: three sand) complete in all respect as per satisfaction of Engineer-in-charge.

15mm (fifteen milimetre) cement plaster in single coat in fair/rough side on brick concrete/stone walls for interior/exterior plastering with all height including arises internal rounded angles chamfers and/or rounded angles not exceeding 80mm (eighty milimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement: six sand) including all leads and lifts and material as directed by the Engineer-in-Charge.

Providing plinth protection 50mm (fifty milimetre) thick in cement concrete 1:3:6 (one cement: three sand: six graded stone aggregate) 20mm nominal size including finishing the top surface of concrete smooth including all leads and lifts of material as directed by the Engineer-in-Charge.

Providing under layer for plinth protection of 75mm (seventy five milimetre) thick unconsolidated bed of dry bricks/ stone aggregate 40mm (forty milimetre) nominal size) well rammed and consolidated and grouted with fine sand including preparation of ground including all leads and lifts of material as directed by the Engineer-in-Charge.

Brick edging (brick laid on edge) to plinth protection with bricks including grouting with cement mortar 1:4 (one cement: four sand) with brick size 22.9 x 11.2 x 7cm (twenty two point nine x eleven point two x seven centimetre) including all leads and lifts of material as directed by the Engineer-in-Charge.

Providing and fixing to wall ceiling and floor galvanized mild steel tube (medium grade) tube fittings and clamps including making good the wall, ceiling and floor complete in all respect as per satisfaction of Engineer-in-charge Jindal / Surya make.

a) 15mm nominal bore

b)25mm nominal bore

Providing and laying in trenches galvanized mild steel tube (Medium grade) tube fitting (earth work in trenches to be measured and paid for separately) complete in all respect as per satisfaction of Engineer-in-charge Jindal / Surya make.

a) 20mm nominal bore

b)25mm nominal bore

Making connection of galvanized steel distribution branch with galvanized mild steel main 20mm to 40mm nominal bore by providing and fixing tee including cutting and threading the pipe complete including all leads, lifts and carriage of material complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing vitreous China wash down, water closet squatting pan (Indian type WC pan) size 580mm complete in all respect as per satisfaction of Engineer-in-charge (earth work, bed concrete, foot rest and trap to be measured and paid for separately) Cera / Hindware make. a) Orrissa Pattern

Providing and fixing vitreous china wash basin with single hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fittings complete in all respect as per satisfaction of Engineer-in-charge Cera / Hindware make. a) Flat back 550x400mm

Providing and fixing C.P. brass waste for wash basin or sink complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing 600x450mm beveled edge mirror of superior glass mounted on 6mm thick A.C. sheet or plywood sheet and fixed to wooden plugs with C.P. Brass screw and washers complete in all respect as per satisfaction of Engineer-in-charge.

Providing and fixing C.P. brass Towel rail complete with C.P. Brass brackets fixed to wooden plugs with C.P. brass complete in all respect as per satisfaction of Engineer-in-charge Jaquar / Nova make. a) 600x20mm size

Providing and fixing C.P. brass bib tap with capstan head complete in all respect as per satisfaction of Engineer-in-charge (Seiko / Smile / Spartan make). a) 15mm dia

Providing and fixing C.P. Brass pillar tap with capstan head complete in all respect as per satisfaction of Engineer-in-charge (Seiko / Smile / Spartan make). a) 15mm dia

Providing and fixing C.P. brass angle valve without nuts and pipe complete in all respect as per satisfaction of Engineer-in-charge. (Seiko / Smile / Spartan make).a) 15mm dia

Providing and fixing PVC connection pipe with brass union complete in all respect as per satisfaction of Engineer-in-charge. a) 45cm length i) 15mm nominal bore.

Providing and fixing brass full way valve with wheel complete in all respect as per satisfaction of Engineer-in-charge.

a) 20mm nominal size

b) 25mm nominal size

Providing and fixing P.V.C. water storage tank of ISI : 12701, GI inlet and outlet connection, 15mm nominal bore ball valve and mosquito proof PVC cover with locking arrangement including hosting upto all height above ground level complete in all respect as satisfaction of Engineer- in-charge Sintex make three layer. a) 2000 ltr. net capacity tank

Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floors etc. complete in all respect as per satisfaction of Engineer-in-charge (Filolex / Vectus / D-Plast make). a) 110mmx75mm

Providing and fixing high pressure PVC spigot and socket, waste and ventilating pipes ISI marked including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Vectus/D-plast make).

a)75mm dia

b) 110mm dia

Providing and fixing PVC door bend with oval access door, insertion rubber washer 3mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Vectus/D-plast make).

a)75mm dia

b) 110mm dia

Providing and fixing PVC collars ISI marked including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Vectus/D-plast make).

a)75mm dia

b) 110mm dia

Providing and fixing PVC plain bend ISI marked complete including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Vectus/D-plast make).

a)75mm dia

b) 110mm dia

Providing and fixing PVC clamps ISI marked of approved design with steel screws and rawl plugs etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Vectus/D-plast make). a) 110mm dia

Providing and fixing PVC size P or S trap for water closet (squatting pan) ISI marked including jointing the trap with the pan and PVC pipe with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Filolex / Vectus / D-Plast make). a) 110mm dia

Providing and fixing PTMT coloured/white high density polyethylene/poly propylene 10 litres capacity (full flush) European standard control low level flushing cistern with fittings with a pair of brackets with fittings such as lead valve, siphon, 15mm nominal size PVC ball valve with polythene float, with push button, couplings for connections with inlet, outlet and over flow pipe, 40mm dia PVC flush bend including cutting holes in walls and making good the same and connecting the flush bend with cistern and closet (overflow pipe to be measured and paid for separately) complete in all respect as per satisfaction of Engineer-in-charge (Cera / Hindware make).

Providing and fixing 100mm dia chromium plated grating of superior quality for floor, gully or nahani trap complete in all respect as per satisfaction of Engineer-in-charge.

Constructing manhole with R.C.C. top slab in 1:2;4 mix (1cement: 2 sand: 4 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 (1cement :4 sand : 8 graded stone 40mm nominal size), inside plastering 15mm thick with cement mortar 1:3 one cement: 3 sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix 1 cement:2sand: 4graded stone aggregate 20mm nominal size finished smooth complete including curing and testing complete in all respect as per satisfaction of Engineer-in-charge. a) Inside size 800x800mm and 500mm deep including 600X450mm SFRC Man hole cover with frame. i) With 200mm thick walls of brick masonry using common burnt clay building bricks in cement mortar 1:3 (1 cement : 3 sand).

Cutting holes through existing brick work including making good the same in C:M 1:6 (1cement:6 sand) per cms depth of cutting complete in all respect as per satisfaction of Engineer-in-charge. i) holes upto and including 400 Sqcm in area.

Providing and fixing aluminium hooks and eyes etc. complete in all respect as per satisfaction of Engineer-in-charge. a) 150mm (One hundred fifty milimetre)

Providing and fixing PVC on railing 50mm wide and 6mm thick as per architectural drawing to the satisfaction of the Engineer-in-Charge.

Providing & fixing wire gauge using galvanized MS wire gauge designation 85 G with wire of dia 0.56mm in aluminium doors, windows, ventilators, shutters and partitions etc. with PVC / Neoprene gasket etc. complete as per the Architectural drawing and the direction of Engineer-in-charge (cost of aluminium snap beading shall be paid in basic item).

Providing & fixing 5mm thick bike light sheet in aluminium doors, windows, ventilators, shutters and partitions etc. with PVC / Neoprene gasket etc. complete as per the Architectural drawing and the direction of Engineer-in-charge (cost of aluminium snap beading shall be paid in basic item).

Providing and fixing P.V.C. waste pipe 32mm dia for wash basin and sink complete in all respect as satisfaction of Engineer- in-charge.

Providing and fixing PVC gully trap with grating brick masonry chamber in cement mortar 1:5 and water tight SFRC cover with frame of 300mmx300mm size. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Vectus/D-plast make). a) 110mm dia P type

Providing and fixing PVC Cowl ISI marked including fixing with approved adhesive etc. complete in all respect as per satisfaction of Engineer-in-charge (Finolex/Vectus/D-plast make). a) 110mm dia

Ravinder Kumar