Loading
Loading…
Loading…
Tender Value
₹6.0 L
EMD Value
₹12,100
Closing Date
8 Oct 2026, 10:30 am
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
45 days
Expenditure
Revenue
HQ
6 conditions · 2 needing a document upload
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
As per Part I Offer Letter, Part II General Instructions to tenderer and Tender Conditions & Annexures-Attached
Mechanical repair works on the Quench Mother Tank and also on released RHF recuperator in Axle Forge Shop (AFS).
RWF-M-OT-AFM-2026-27-64~RWF
RWF-M-OT-AFM-2026-27-64
Open
Works - General
12 Months
Bengaluru Urban, Karnataka
₹0
₹12,100
16 Sept 2026
16 Sept 2026
24 Sept 2026
6 items across 2 schedules
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | 4,22,440 | ||
| Lumpsum 422440.00 | 1.00 | — | — | ||
| 1. Pipeline Extension 1.1 Gas-cut the fasteners of the flanged joints and dismantle the 150 NB pipeline connections, including the gate valves, strainers/filters, and the filling pump installed in the filling line (from the mother tank to the quench tank) and the draining line (from the quench tank to the mother tank). Carefully disconnect all flanged joints without causing damage to the reusable pipelines, valves, fittings, or equipment, and remove the components for shifting or reinstallation as required.-1 Set1.2 Shift the 150 NB pipeline sections, including flanges, bends, gate valves, filters, and all associated fittings, from the storage area to the designated work location.-1 Set1.3 Extend and connect the inlet and outlet pipelines to the mother tank at the new location using 150 NB pipelines (Approx. Qty: 160 m). Position the pipelines for both the filling line (from the mother tank to the quench tank) and the draining line (from the quench tank to the mother tank), incorporating the required flanges, elbows/bends, and fittings to maintain proper alignment and flow direction. Carry out temporary tack welding to hold the pipeline in position while ensuring the required gradient is maintained to facilitate smooth flow and prevent air locking or back pressure. After verifying the alignment, straightness, and fit-up of the entire pipeline, complete the joints by carrying out multiple-pass fillet welding. Provide suitable pipe supports and anchors at regular intervals to prevent sagging, vibration, and displacement during operation. Install and connect the gate valves, strainers/filters, and pumps, ensuring correct orientation of all valves for ease of operation and maintenance. Use suitable gaskets at all flanged joints to ensure leak-proof sealing. Upon completion of the installation, conduct a thorough inspection and leak test of the pipeline system. Rectify any leakage or defects by re-welding, replacing defective gaskets, or renewing damaged pipeline sections as required.-1 Set2. Servicing of Quench Mother Tank2.1 Shift the 12 mm plates to the work site and cut them to the required sizes for fabrication of the support legs. Fabricate/rebuild the six support legs using the 12 mm plates. Position the newly fabricated support legs at the designated location. Gas-cut and remove the damaged/corroded support legs of the mother tank (Qty: 6 Nos.). After positioning the mother tank on the new support legs, carry out multiple-pass fillet welding to securely join the tank to the support legs.-1 Set2.2 After positioning and grouting the support structure for the mother tank, cut open the top side of the tank to provide one additional flange opening for fitment. Thoroughly clean the inside of the tank to remove scales, debris, and any other foreign materials. Clean and prepare both the internal and external surfaces of the tank for painting.- 1 Set2.3 After thorough cleaning and scale removal inspect the tank walls for corrosion and any material damages. If any repair the damaged portion by using 6mm MS plate and weld thoroughly.-1 Set2.4 Paint the inner and outer surfaces of the Mother Tank with two coats of approved primer followed by two coats of approved paint, complete in all respects, including finishing.-1 Set2.5 Remove all the debris/released items from the vicinity of the machine, clean the entire area, dispose the debris/released items to the nominated of place- 1 Set3. Supervision charges-1 No | — | — | — | 4,22,440 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
PartIOfferletter.pdf
ATTACHMENT
PartIIInstructionstoTenderers.pdf
ATTACHMENT
PartIIISpecialconditions.pdf
ATTACHMENT
PartIVPricesandpayments.pdf
ATTACHMENT
PartVBreakupofratesandschedule.pdf Part V Schedule of work
ATTACHMENT
PartVIAnnexures.pdf
ATTACHMENT
PartVIINITfore-tender.pdf
ATTACHMENT
Part VIII GCC
ATTACHMENT
PartVBreakupofratesandschedule.pdf
ATTACHMENT
GCC_April-2022_merged_compressed.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .