Routine Maintenance Works of Various Infrastructure at PDPMC, Paradip

Carriage of lime, moorum, building rubbish and debris including refractory / insulation debris etc. by mechanical transport for following leads or part thereof including loading, unloading and stacking all complete as per the direction of the Engineer-in-Charge (The rates will be applicable to net quantities after deduction of 20 percent for voids):

Upto a lead of 1 km.

Lead beyond 1 km but upto 2 km.

Lead beyond 2 km but upto 3 km.

Lead beyond 3 km but upto 4 km.

Lead beyond 4 km but upto 5 km.

Carriage of earth by mechanical transport for following leads or part thereof including loading, unloading and stacking all complete as per the direction of the Engineer in- Charge (The rates will be applicable to net quantities after deduction of 20 percent for voids):

Upto a lead of 1 km.

Lead beyond 1 km but upto 2 km.

Carriage of oily sludge, bio sludge, fecal sludge, ETP sludge etc. or manure by mechanical transport for following leads or part thereof including loading, unloading and stacking all complete as per the direction of the Engineer-in-Charge (The rates will be applicable to net quantities after deduction of 8 percent for voids):

Upto a lead of 1 km.

Lead beyond 1 km but upto 2 km.

Lead beyond 2 km but upto 3 km.

Lead beyond 3 km but upto 4 km.

Supply of tractor with trailer on hire charges for 08 hours per day including rendering the services of 4 labourers driver, fuel and other consumables, tools, tackles etc. for transportation of rubbish/ waste materials complete as per directions of Engineer-in-Charge.(8 hours working period of one tractor is considered as one tractor day). Unit "EACH" (EA) stands for tractor days.

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in- charge, beyond 50 m initial lead, for all loads including all lifts involved.

Excavation work by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains not exceeding 1.5m in width or 10 sqm on plan including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within a lead of 50m:

Ordinary rock.

Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including disposal of excavated earth up to 50 m and lift up to 1.5 m, disposed soil to be levelled and neatly dressed : All kinds of soil.

Pipes, cables etc. not exceeding 80 mm dia.

Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m: All kinds of soil.

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.

Felling trees of the girth (measured at a height of 1 m above ground level) including cutting of trunks and branches, removing the roots and stacking of serviceable material and disposal of unserviceable material:

Beyond 30 cm girth up to and including 60 cm girth.

Beyond 60 cm girth up to and including 120 cm girth.

Supplying chemical emulsion in sealed containers including delivery as specified : Chlorpyriphos/ Lindane emulsifiable concentrate of 20%.

Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc : With Chlorpyriphos/ Lindane E.C. 20% with 1% concentration. (Chlorpyriphos 20% E.C./Lindane 20% E.C. to be supplied free of cost @ 1.125 Litre per 10 metre).

Cement mortar 1:4 (1 cement : 4 fine sand).

Cement mortar 1:6 (1 cement : 6 fine sand).

Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering - All work up to plinth level :

1:3:6 (1 Cement : 3 coarse sand (Zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources).

1:2:4 (1 cement : 2 coarse sand (Zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources).

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centring, shuttering and finishing:

1:3:6 (1 cement : 3 coarse sand (Zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from natural sources).

1:2:4 (1 Cement : 2 coarse sand (Zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources).

Applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :

1:2:4 (1 cement : 2 coarse sand (Zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources).

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. up to floor five level excluding cost of centering, shuttering, finishing and reinforcement :

1:1.5:3 (1 Cement: 1.5 coarse sand including manufactured sand derived from Recycled concrete aggregate (RCA) upto 20% : 3 graded stone aggregate 20 mm nominal size including Recycled concrete aggregate (RCA) upto 20%).

Thermo-Mechanically Treated bars.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in:

Cement mortar 1:6 (1 cement : 6 coarse sand).

Brick work with commonburnt clay F.P.S. (nonmodular) bricks of classdesignation 7.5 insuperstructureaboveplinth level up to floor V level in all shapes and sizes in :

Cement mortar 1:4 (1 cement : 4 coarse sand).

Cement mortar 1:6 (1 cement : 6 coarse sand).

Half brickmasonrywith common burnt clay F.P.S. (non modular) bricksof classdesignation7.5 insuperstructure above plinth level up to floor V level:

Cement mortar 1:3 (1 cement :3 coarse sand).

Brick edging laid lengthwise with half brick depth including excavation, refilling and disposal of surplus earth lead up to 50 metres - With common burnt clay F.P.S. (non modular) bricks of class designation 7.5.

Dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud mortar including filling joints with Jamuna sand (with common burnt clay F.P.S. (non modular) bricks) complete.

Providing and fixing 18mm thick gang saw cut mirror polished premoulded and prepolished) machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble - Area of slab up to 0.50 sqm.

Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble - Area of slab over 0.50 sqm.

Granite of any colour and shade - Area of slab up to 0.50 sqm.

Granite of any colour and shade - Area of slab over 0.50 sqm.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS : 15622 (thickness to be specified by the manufacturer) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing in position wall panelling at all heights with integral densified calcium silicate panels/ tiles of size 595 X 595 mm, having NRC (noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (Part-4), fire performance as per BS:476 (part 6 & 7), humidity resistance of 100%, thermal conductivity < 0.043 W/m K as per ASTM 518:1991, comprising of a frame made from especially fabricated galvanised mild steel sheet 0.50 mm thick pressed section (galvanizing @120 grams per sqm including both sides) i.e. vertical studs of size 48 x 34 x 36 mm are placed at 600 mm center to center in a floor and ceiling channel section of size 50 x 32 m fixed to the floor and soffit at 600mm centers using 12 mm dia, 50 mm long wedge type expanded zinc alloy dash fastner with 10 mm bolt. This same channel is then to be fixed in horiziontal direction at 600 mm center to center so as to form a grid of 600 mm X 600 mm. Glasswood of non combustible panels/ tiles are to be screw fixed with self tapping pan head even nickel coated mild steel screws of size 13 X 3.2 mm on to this grid leaving an even groove of 1 mm between the panels. The joints between the panels are to be duly jointed and finished using recommended jointing clalcium silicate based compound and fiber joint tape roll 50 mm wide (90 metre) roll and two coats of primer suitable for panelling as per manufacturer's specification as per direction of engineer in-charge all complete: With 15 mm thick fully perforated square/ butt edge light weight calcium silicate panels/ tiles

Structural steel work in single section fixed with or without connecting plate including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required:

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying a priming coat of approved steel primer:

M.S. tube.

G.I. pipes.

Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows all complete with:

With 5.5 mm thick glass panes.

Welding by gas or electric plant including transportation of plant at site etc. complete.

Brick on edge flooring with bricks of class designation 7.5 on a bed of 12 mm cement mortar including filling the joints with same mortar with common burnt clay F.P.S. (non modular) bricks:

1:6 (1cement : 6 coarse sand).

62 mm thick cement concrete flooring with concrete hardener topping, under layer 50 mm thick cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) and top layer 12mm thick cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate, 6mm nominal size) by volume, hardening compound mixed @ 2 litre per 50kg of cement or as per manufactures specifications. This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer) of approved make in colours, shades exept burgundy, bottle green, black of any size as approved by Engineer-in-charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @3.3 kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer) with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make in all colours & shade in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement & matching pigments etc. complete:

Size of Tile 600x600 mm.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion: Single socketed pipes:

75 mm diameter.

110 mm diameter.

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion.

Coupler - 75 mm.

Coupler - 110 mm.

Bend 87.5° - 75 mm bend.

Bend 87.5° - 110 mm bend.

Shoe (Plain) - 75 mm Shoe.

Shoe (Plain) - 110 mm Shoe.

Single tee with door - 110x110x110 mm.

Single tee without door - 110x110x110 mm.

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete:

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the rate of 1200 mm centre to centre to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095 (Part I) : 2011 (Board with BIS certification marks).

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm + 0.05 %, total coated thickness with zinc coating 120 gsm as per IS: 277 in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length up to 12 metre or as desired by Engineer-in- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55mm) with EPDM seal, complete up to any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and applying two coats of High Albedo paint having minimum Solar Reflective Index (SRI) 108 (with solar reflectance & thermal emittance tested as per ASTM) C 1549 and ASTM C 1371 respectively), VOC less than 10 cc/gm. The coating thickness and the methodology of application shall strctly as per manufacturer’s specifications and as approved by engineer In charge. Surface preparation includes cleaning with metal wire brush to remove all dust, fungus etc., washing with water all complete. The contractor shall give guarantee for the perfomance of SRI and also the durabitity of coating, all complete as per direction of Engineer-in-charge.

POLYCARBONATE SHEET: Providing and fixing 5 mm thick transparent Polycarbonate sheets of approved quality, colour and shade as decided by Engineer-in-charge. The sheet shall be fixed using self drilling screw with bitumen washer complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses, windows frame and including cutting to size and shape wherever required with all materials, tools and tackles, labour, consumables etc complete.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm + 0.05 % total coated thickness, Zinc coating 120gsm as per IS: 277 in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete :

Ridges plain (500 - 600mm).

Gutter (600 mm over all girth).

Dismantling C.I. or asbestos rain water pipe with fittings and clamps including stacking the material within 50 metres lead :

100 mm dia pipe.

150 mm dia pipe.

15 mm cement plaster on the rough side of single or half brick wall of mix :

1:4 (1 cement: 4 fine sand).

1:6 (1 cement: 6 fine sand).

6 mm cement plaster of mix : - 1:3 (1 cement: 3 fine sand).

Neat cement punning.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete:

On steel work.

Lettering with black Japan paint of approved brand and manufacture. Note: Rate EACH (EA) stands for "Per letter per cm height".

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour:

One coat.

Finishing walls with Acrylic Smooth exterior paint of required shade :

Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface).

Finishing walls with Acrylic Smooth exterior paint of required shade - New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm).

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

French spirit polishing - One or more coats on old work.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade - One or more coats on old work.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade - Two or more coats on new work.

Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour:

One coat.

Two coats.

Repairs to plaster of thickness 12mm to 20mm in patches of area 2.5 sq. meters and under including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50metres lead :

With cement mortar 1:4 (1 cement : 4 fine sand).

With cement mortar 1:4 (1cement: 4 coarse sand).

Cleaning of terrace/ loft water storage tank (inside surface area) upto 2000 litre capacity at all heights with coconut brushes, duster etc., removal of silt, rubbish from the tank and cleaning the tank with fresh water disinfecting with bleaching powder @0.5gm per litre capacity of tank including marking the date of cleaning on the side of tank body with the help of stencil and paint and disposing of malba all complete as per direction of engineer-in-charge. (The old date already written on tank should be removed with paint remover or black paint and if date is not written with the stenchil or old date is not removed deduction will be made @Rs0.10 per litre) (if during cleaning any GI fittings or ball cock is damaged that is to be repaired by contractor at his own cost and nothing extra will be paid on this account).

Cleaning and desilting of gully trap chamber, including removal of rubbish mixed with earth etc. and disposal of same, all as per the direction of Engineer-in-charge.

Cleaning of chocked sewer line by diesel running vehicle mounting hydraulic operated high pressure suction cum jetting sewer cleaning machine fitted with pump having 4000 litres suction capacity and 6000 litres water jetting tank capacity including skilled operator, supervising engineer etc. for cleaning and partial desilting of manholes and dechocking of sewer lines. Dechocking and flushing of sewer line from one manhole to another by high pressure jetting system of 2200 PSI of sewer line from 150mm dia upto 300mm dia for all depth.

Disconnecting damaged overhead / terrace PVC water storage tank of any size from water supply line and removing from the terrace including shifting at ground level as per direction of Engineer-in-charge.

Dismantling W.C. pan of all sizes including disposal of dismantled materials i/c malba all complete as per direction of Engineer-in-charge.

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge:

Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix).

Demolishing R.C.C. work manually/ by mechanical means

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge:

In cement mortar.

Dismantling steel work in single sections including dismembering and stacking within 50 metres lead in:

R.S. Joists.

Channels, angles, tees and flats.

Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead.

Dismantling steel work manually/ by mechanical means in built up sections without dismembering and stacking within 50 metres lead as per direction of Engineer-in-charge.

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead:

For thickness of tiles 10 mm to 25 mm.

For thickness of tiles above 25 mm and up to 40 mm.

Dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of:

G.S. Sheet.

Dismantling barbed wire or flexible wire rope in fencing including making rolls and stacking within 50 metres lead.

Dismantling wooden boardings in lining of walls and partitions, excluding supporting members but including stacking within 50 metres lead :

Thickness above 25 mm up to 40 mm.

Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead.

Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead.

Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead.

Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable surplus material and stacking of serviceable material with in 50 meters lead as directed by Engineer-in- charge.

Providing and applying 2.5mm thick road marking strips (retro-reflective) of specified shade/ colour using hot thermoplastic material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour ,T&P, cleaning the road surface of all dirt, seals, oil, grease and foreign material etc. complete as per direction of Engineer-in-charge and accordance with applicable specifications.

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc. of required strength, thickness & size/shape,made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand,compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as per direction of Engineerin-Charge:

60mm thick Cement Concrete paver block of M-35 grade with approved colour, design & pattern.

Providing and fixing G.I. chain link fabric fencing of required width in mesh size 50x50mm including strengthening with 2mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge:

Made of G.I. wire of dia. 4mm, PVC coated to achieve outer dia. not less than 5mm in required colour and shade.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required :

W.C. Pan with ISI marked white solid plastic seat and lid.

Providing and fixing wash basin with C.I. brackets, 15 mmC.P. brasspillar taps,32mmC.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the wallswherever required :

White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps.

Stainless Steel AISI-304(18/8) Round basin 405x355 mm with single 15 mm C.P. brass pillar tap.

Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete:

10 litre capacity - White.

Providing and fixing solid plastic seat with lid for pedestal type W.C. pan complete :

White solid plastic seat with lid.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete:

Flexible pipe - 32 mm dia.

Flexible pipe - 40 mm dia.

Providing and fixing 600 x 450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing toilet paper holder :

C.P. brass.

Providing and fixing PTMT 15 mm Urinal spreader size 95x69x100 mm with 1/2 BSP thread and shapes. Weighing not less than 60 gms.

Providing and fixing PTMT urinal cock of approved quality and colour - 15 mm nominal bore, 80mm long. 42 mm high and 30mm wide with BSP female threads weighing not less than 48 gms.

Providing & fixing white vitreous china water less urinal of size 600 x 330 x 315 mm having antibacterial /germs free ceramic surface, fixed with cartridge having debris catcher and hygiene seal.

Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/6 litre (adjustable to 4 litre/8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete.

Providing and fixing 8mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer-in-charge.

Providing and fixing water closet squatting pan (Indian type W.C. pan )with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required :

White Vitreous china Orissa pattern W.C. pan of size 580x440mm with integral type foot rests.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430 x 260 x 350 mm or 340 x 410 x 265 mm sizes respectively.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge: Internal work - Exposed on wall:

15 mm nominal outer dia pipes.

20 mm nominal outer dia pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge: Concealed work including cutting chases and making good the walls etc:

15 mm nominal dia pipes.

20 mm nominal dia pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching ,refilling & testing of joints complete as per direction of Engineer in Charge: External work:

15 mm nominal dia pipes.

20 mm nominal dia pipes.

Providing and fixing brass bib cock of approved quality :

15 mm nominal bore.

20 mm nominal bore.

Providing and fixing brass stop cock of approved quality :

15 mm nominal bore.

20 mm nominal bore.

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

32 mm nominal bore.

50 mm nominal bore.

80 mm nominal bore.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 - 15 mm nominal bore.

Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. - 15 mm nominal bore.

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931 - 15 mm nominal bore.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore.

Providing and fixing C.P. brass extension nipple (size 15mm x 50mm) of approved make and quality as per direction of engineer-in-charge.

Providing and fixing PTMT bib cock of approved quality and colour:

15mm nominal bore, 86 mm long. Weighing not less than 88 gms.

15 mm nominal bore, 122mm long. Weighing not less than 99 gms.

15 mm nominal bore, 165mm long. Weighing not less than 110 gms.

Providing and fixing PTMT stop cock of approved quality and colour:

15 mm nominal bore, 86mm long. Weighing not less than 88 gms.

20mm nominal bore, 89mm long. Weighing not less than 88 gms.

Concealed stop cock, 15mm nominal bore, 108mm long. Weighing not less than 108 gms.

Providing and fixing PTMT pillar cock of approved quality and colour:

15mm nominal bore, 107mm long. Weighing not less than 110 gms.

15mm nominal bore, 125mm long foam flow. Weighing not less than 120 gms.

Providing and fixing PTMT, push cock of approved quality and colour:

15 mm nominal bore, 98mm long. Weighing not less than 75 gms.

15 mm nominal bore, 80mm long. Weighing not less than 46 gms.

Providing and fixing PTMT grating of approved quality and colour:

Circular type. - 100 mm nominal dia.

Circular type. - 125 mm nominal dia with 25 mm waste hole.

Rectangular type with openable circular lid. - 150 mm nominal size square 100 mm diameter of the inner hinged round grating.

Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball:

15 mm nominal bore, 105 mm long. Weighing not less than 138 gms.

20 mm nominal bore, 120 mm long. Weighing not less than 198 gms.

25 mm nominal bore, 152mm long. Weighing not less than 440 gms.

40mm nominal bore, 206mm long. Weighing not less than 690 gms.

50mm nominal bore, 242mm long. Weighing not less than 1240 gms.

Providing and fixing PTMT angle stop cock 15 mm nominal bore. Weighing not less than 85 gms.

Providing and fixing PTMT swivelling shower, 15mm nominal bore. Weighing not less than 40gms.

Providing and fixing PTMT soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements. Weighing not less than 106 gms.

Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour:

15 mm nominal bore with 30cm length.

15 mm nominal bore with 45cm length.

Providing and fixing PTMT extension nipple for water tank pipe, fittings of approved quality and colour:

15 mm nominal bore. Weighing not less than 32 gms.

20mm nominal bore. Weighing not less than 40gms.

25mm nominal bore. Weighing not less than 62 gms.

Providing & fixing chrome plated brass battery based infrared sensor operated pillar cock, having foam flow technology - 15 mm nominal bore.

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight up to 125 kg., for doors, including cost of cutting floors , embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge:

With stainless steel cover plate minimum 1.25 mm thickness.

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete :

Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :

Providing and fixing aluminium pull bolt lock anodised ISI marked (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws bolts, nut and washers etc. complete.

Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete.

Twin rubber stopper.

Providing and fixing bright finished brass 100 mm mortice latch and lock ISI marked with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles with necessary screws etc. complete (Best make of approved quality).

Chipping of unsound/ weak concrete material from slabs, beams, columns etc. with manual Chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of Engineer- in-charge:

75 mm average thickness.

50 mm average thickness.

25 mm average thickness.

Providing and injecting approved grout in proportion recommended by the manufacturer into cracks/ honey-comb area of concrete/ masonry by suitable gun/ pump at required pressure including cutting of nipples after curing etc. complete as per directions of engineer-in-charge (The payment shall be made on the basis of actual weight of approved grout injection):

Epoxy injection grout in concrete/ RCC work of approved make.

PLYWOOD/BLOCKBOARD: Providing and fixing of commercial plywood /blockboard of approved make in shelves/for furniture etc. with screws and fittings wherever required (Fittings to be paid separately).

18 MM Thick BWR plywood (BWR Grade as per IS-303)

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S including cost of adhesive of approved quality:

1.0 mm thick.

PVC SHEET/TILES: Providing and fixing homogeneous Polyvinyl chloride (PVC) sheet / tile of approved quality, colour and shade in flooring and skirting in approved pattern on a smooth and damp-proof base without any air pocket using rubber based adhesives of approved quality and manufacturer like Dunlop S-758, Fevicol SR-998 or equivalent including rolling with light wooden roller weighing about 5kg all complete with all labour, materials, consumables, tools and tackles and as directed by Engineer- in-Charge.

1.5 mm thick sheet

1.5 mm thick Tile

SUN CONTROL FILM: Providing and installing Sun control polyester insulating film of reflective/ non-reflective type as specified below, of approved shade (sun control films of M/s Garware or approved equivalent) on glasses of windows / door / partitions including thorough cleaning of glass surfaces, scaffolding etc. with all labour and materials complete as per manufacturer's specifications and directions of the Engineer-in-Charge.

Reflective type

Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete - up to 5mm depth and 5 mm width.

Cleaning the tiles, lavatory, flooring, urinals etc. by removing stains etc. by using Vim powder / cleaning powder / ISI grade black phenyle / while phenyle / Acid /Naptha balls / Coir brushes / wire brushes / Finit in required proportion to make the area clean and free from all dust, dirt and stains etc. including cost of all labour and materials complete. (Only floor area shall be measured).

Cleaning and desilting of drains, side slopes in or under water or above water level and along drain both sides upto 1.0 metre width including removal of grass, bushes, vegetation, debris, sludge and any other unwanted material and disposal of the same at places as directed by Engineer- in-Charge within owner's premises including all labour, materials, tools, tackles, transportation for all lead and lifts as directed.

Cross section of drain upto 2.0 sqm.

Cross section of drain above 2.0 sqm. and upto 4.0 sqm.

Cross section of drain above 4.0 sqm. and upto 10.0 sqm.

Cross section of drain above 10.0 sqm and upto 15.0 sqm.

Labour charges for cleaning and dechoking of the nahani trap, gully trap and inspection chambers alongwith the CI and SW pipe connection of house drainage including flushing, removal of sludge muck outside all labour, tools etc. complete. The contractor has to clean the line from Nahani trap upto inspection chamber or vice-versa complete.

Cleaning dechoking and flushing inspection chambers and connected drain lines with drain cleaning rods, bamboos, compressed air, steaming etc. removal of oily muck outside the chamber completed upto 100M lead. The item includes transportation of all machinery and plants, all labour, tools etc. complete, taking all necessary safety precautions as specified. Water at one point shall be supplied free of cost, hire charges for compressed air shall be paid separately if required.

Cleaning, dechoking and flushing 100mm/ 50mm SW and sewer line by removing muck, cleaning etc. with bamboo strips or sewer cleaning rods etc. as directed (section between two chambers) all complete including cleaning of two manholes as per direction of the Engineer-in Charge..

600mm long towel rail with total length of 645mm, width 78mm and effective height of 88mm, weighing not less than 190gms.

Providing and fixing of Turbo ventilator Stainless Steel (S.S) TurboRoof Air Ventilators comprising of a Stainless Steel (S.S.) Turbine Fan of Throat Dia Size 24inch (600 MM) to be mounted over a Polycarbonate/FRP Base Frames. (Base frames, screws, sealants etc to be supplied by contractor)

Supply and application of Moisture cure Polyurethane Foam (pidlite or equivalent of 750ml pack) with required tools, tackles, consumables, thinner etc. as per instruction of EIC.

Artistic painting like tribal art, slogan, wall poster etc. as approvedby Engineer In Charge by applying two or more coat of acrylic paintovera coat of primer on plastered surface of boundary wall or otherlocation. The picture shall be depicted or painted in multicoloursynthetic enamel paint over base of acrylic paint, including allmaterial, labour all complete. (including surface preparation)

Providing services for structural repairing works involving gas cutting,grinding, welding etc. of MS structure of all types at all heightsincluding supply of all equipments /machineries/consumables like gascutting set,welding machines, grinding machines, gases, weldingelectrodes and any other materials with all labours like gas cutters,grinders, welders, unskilled labours etc required to carry out the jobsetc. with scaffolding complete as directed by Engineer InCharge.(Payment will be made on actual hour of work done i.e excludingtime required for connection of welding machine, mobilization etc)

Providing and fixing floor-spring of approved make for frameless glassdoor. The job includes taking out of glass door shutter, replacing thedamaged floor spring with the new one, re-fixing the glass door shutter,alignment & balancing of the glass door thereafter etc. all completeincluding the cost of consumable and as per the direction and to thefull satisfaction of the Engineer-In-Charge.

Repairing of false flooring by removing and refixing/adjusting the sides and supports wherever required by providing aluminium angle fixing with screws with all labourcomplete as per directions of the Engineer-in-charge.

Thorough cleaning of all the doors and windows and rectifying all the doors to openable condition by smoothening the edges of door shutters and door frames tightening the screws handles etc. and repairing, realigning and servicing in position of steel windows and ventilatiors etc including oiling, greasing and making it in working order with alllabours but excluding cost of fitting, fixtures but including cost of screws and nails etc.

Maintenance of floor spring machine of aluminium door, cleaning of glasses and aluminium sections with necessary soaps, water etc.including removing, re-fixing and aligment of the leafs, locking deviceetc. complete with all labour and materials as per direction ofEngineer-in-Charge including over hauling of floor spring machine,changing of oil seal & spares.

Supplying and operating of Hydra/crane tyre mounted for lifting and shifting of valves, equipments, pipes, pipe fittings, plates, pumpetc inside station premises as directed by Site Engineer/EIC whichincludes mobilization charges, manpower, fuel charges, tools ,tackles,etc .Note:- Measurement will be done on operating hour basis for Hydra/crane operation only: Hydra of capacity more than 5 MT but up to 15 MT

Providing & fixing vertical blinds 100mm width comprising of polymer coated fibre (make -Vista or approved equivalent) as per AS standards. The fabric shall be finished on the sides with edge tape duly welded for waviness control. Fabrication shades shall be fabricated according to specification and accurate to tolerance established by SWF engineering standards.

Providing services related to civil maintenance (Plumbing/Carpentery services) by deploying suitable manpower including tools, tackles, consumables etc required for site -(As on requirement basis by EIC)

Providing services related to civil maintenance by deploying suitable semi skilled manpower including tools, tackles, consumables etc required for site -(As on requirement basis by EIC)

Design, Fabrication, Printing, Supply and installation of MS Boards: MS board consists of - MS board mounted on MS angle frame, MS angle legs welded with foot rest pedestal. Installation at place as per direction with RCC grouting.

Providing & laying M-Seal or equivalent with all labour & materials complete as direction of Engineer-in-Charge.

Supply and Operation of Gully sucker (of Capacity 5000 Ltr) on Hire tosuck waste water including mud and sludge from sewage treatment plant of township and transportation it to a suitable disposal point inside paradip refinery with all fuel and other consumables and operatingstaff for all lifts & lead upto 10 km including loading, unloading fromone place to another place inside and outside battery area all complete as per the direction of the Engineer-in-Charge.Note: Unit of measurement is EACH, which stands for 'Per Trip'.

Repairing the rolling shutters, removing from the position with gear box and drums etc. repairing the jammed and damaged sideclamps, guide channels straightening the drums, springs, washing and cleaning with diesel/kerosence, oiling and greasing the moving parts, erection and grouting the shutter back into proper position,grouting with cement mortar as per original all complete.

Upto 12 Sqm

Upto 20 Sqm

Overhauling of the rolling shutter by removing the drums,straightening the side channels, tightening of spring, washing,cleaning and oiling greasing of the moving and other parts, side channel etc. for smooth operation and putting back drum in position, all labour tools plants etc. complete.

Upto 12 Sqm

Upto 20 Sqm

Supplying and fixing approved, Julla swing hinges with ball bearings of standard quality and size including breaking concrete and removing surface as per original all labour and materials complete.

Replacing the damaged parts of the rolling shutters with new approved parts including removing and refixing the shutters ifnecessary and sending the damaged materials to departmental stores, with all labour and material complete.

Shaft rod

Strips

Springs

Iron pully

MS Gear Worm with padal

MS Gear wheel

Ball bearing

Locker

Brackets

Supplying & fixing Pigeon Protection net of mesh 15 mm x 15 mm & Gauge SW14 in sheds including specials required for bolting with tie members of truss,painted with two coats of synthetic enamel paint of over a coat of red oxide zinc chrome primer complete in allrespects inclusive of cost of all labour, materials, tools, tackles etc. as per drawings, specifications and direction of the Engineer-in-Charge.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 4.0 mm thickness.

With float glass panes of 5.50 mm thickness.

With float glass panes of 8 mm thickness.

Providing and supplying Spandrel Glass Panels comprising of 6 mm thick heat strengthened monolithic float glass of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade so as to match the colour and shade of the IGUs in the vision panels etc. ,all complete for the required performances as specified, as per the Architectural drawings, as per the approved shop drawings, as specified, and as directed by the Engineer- in- Charge. For payment, only the actual area of glass on face # 1 of the glass panels (but excluding the area of grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm.(Payment for fixing of Spandrel Glass Panels in the curtain glazing is included in cost of relevent Item*).

Supplying and filling in plinth with Jamuna sand under floors, including watering, ramming, consolidating and dressing complete.

Self priming HB coating primer to achive a minimum DFT of 100- 125 microns (1 or more coat of 100-125 μ)

HB Epoxy MIO to achive a minimum DFT of 100-150 microns (one or more coat of 100-150 μ).

Two pack Acrylic Poly-urethane (PU) to achive a minimum DFT of 40-50 microns (one or more coat of 40-50 μ).

HIRING OF Diesel operated ARTICULATED BOOM LIFT : Job involves the following: 1. Supply of 01 no. of Diesel operated articulating boom lift. 2. Deputation of 01 operator & 01 helper for boom lift. 3. Diesel, Oils and every other consumable required for its functioning is in contractor's scope. 4. Maintenance of supplied equipment is in contractor's scope. 5. The boom lift should have working height of 25-30 mtr, approximately 1m x 2m platform and covered by hand rails and toe gaurd for prevention of accident. Lifting capacity should be 200-250 kg with 360 deg movement. 6. The operation of the equipment shall be on 8 hours basis including Sunday & holiday (i.e. 8 hour each per day). However on sundays and holidays, Overtime Payment shall be given separately for operator and helper. The Hire days shall be calculated from the date of mobilization of equipment at site till the date of instruction from EIC/site engineer for demobilization of equipment.

Providing and operating Hydraulic Excavator of 1 cum bucket with driver and fuel(JCB) on hourly basis with driver for various miscellaneous civil worksviz. uprooting of big bushes, shifting & removal of debris removal of earth heaps, cleaning of road blocks, excavation of earth heaps,cleaning of road blocks, excavation of earth any other work in Paradip Refinery including cost of diesel and other consumables etc.Complete as per the direction of Engineer-in-charge.

Providing and operating Water tanker 5000 litre with driver for various miscellaneous works including cost of diesel and other consumables etc.

Reparing of flush. by replacing / refixing of required part as approved by Engineer in Charge with necessary tools

Replacement of ballcock

Replacement of syphon unit

Replacement of syphon washer

Replacement of side handle

Replacement of push bottom handle with accessories.

Replacement of bracket

Replacement of 2 in 1 health forcet of size 350 mm X 450 mm, ivory orwhite in colour of make watertec, Prayag or approved equivalent withnecessary accessories, tools and tackles all complete with all labour, transpotation etc. complete

Providing and fixing best/superrior quality CP Health faucet with 1 mmetallic long tube ,hooks and angle cock including all tools,fittingsand fixing charges in each room of brand jaquar,marc,kingston,etc andany other approved brand all complete as per direction of theEngineering-in-Charge.

Reparing of existing urinal/wash basin sensors by replacing /refixing of required part as approved by Engineer in Chargewith necessary tools and tackles all complete with all labour ,transpotation etc. complete.

Battery

solenoid valve

Sensor-Eye

Loop Plate

Connector

Black Plate

Closing plate

Outlet Valve

Ball Cock

Syphone

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption's less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete:

Size of Tile 600x600 mm.

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption's less than 0.08% and conforming to IS : 15622 of approved brand and manufacture, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) jointing with grey cemet slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only. Laying of tiles will be done with the notch trowel, plier, wedge, clip of required thickenss, levelling system and rubber mallet for placing the tiles gently and easily:

Double charge vitrified tile polished finish of size- Size of Tile 600x600 mm.

Double charge vitrified tile polished finish of size - Size of Tile 600x1200 mm.

Glazed vitrified tile Matt/Antiskid finish of size - Size of Tile 600x600 mm.

Glazed vitrified tile Matt/Antiskid finish of size - Size of Tile 600x1200 mm.

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content

With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre.

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double action hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid separately)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-incharge. (Glazing, paneling and dash fasteners to be paid for separately) :

For fixed portion - Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15).

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) - Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15).

Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge.

Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side.

Pre-laminated particle board with decorative lamination on both sides.

Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick & 2100 mm long with SS screws etc .complete as per direction of Engineer-in-Charge:

Anodized (AC 15 ) aluminium tubular handle bar

Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.

Providing and fixing tiled false ceiling of approved materials of size 595x595 mm in true horizontal level suspended on inter locking metalgrid of hot dipped galvanized steel sections ( galvanized @ 120gsm/sqm, both side inclusive) consisting of main T" runner withsuitably spaced joints to get required length and of size 24x38mm" joints to get required length and of size 24x38mm made from 0.30mm thick (minimum) sheet, spaced at 1200mm center to center and cross "T" of size 24x25mm made of 0.30mm thick (minimum) sheet, 1200mm long spaced between main "T" at 600mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600mm and size 24x25mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600mm panel to form grids of 600x600mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, wherever, required, cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 x mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete at all heights as per specifications drawings and as directed by Engineer-in-charge:

GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and 0.5mm thick with 8mm drop; made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending.

12.5 mm thick fully Perforated Gypsum Board tile made from plasterboard having glass fibre conforming to IS: 2095 part I , of size 595x595 mm, having perforation of 9.7x9.7 mm at 19.4 mm c/c with center borders of 48 mm and the side borders of 30 mm, backed with non woven tissue on the back side, having an NRC ( Noise Reduction Coefficient) of 0.79, with 50 mm resin bonded glass wool backing.

Providing and Fixing 15 mm thick densified tegular edged eco friendlylight weight calcium silicate false ceiling tiles of approved texturespintone/cosmos / Hexa or equivalent of size 595 x 595 mm in truehorizontal level suspended on inter locking metal grid of hot dippedgalvanised steel sections (galvanising @ 120 grams per sqm includingboth side) consisting of main 'T' runner suitably spaced at joints to getrequired length and of size 24x38mm made from 0.33 mm thick made from 0.33 mm thick (minimum) sheet, spaced 1200mm centre to centre, and cross "T" of size 24x28mm made out of 0.33mm (Minimum) sheet, 1200mm long spaced between main'T' at 600mm centre to centre to form a grid of 1200x600mm and secondary cross 'T' of length 600mm and size 24 x28mm made of 0.33mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600mm panel to from grid of size 600x600mm, resting on periphery walls /partitions on a Perimeter wall angle pre- coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450mm centre to centre with 25mm long dry wall screws @ 230mm interval and laying 15mm thick densified edges calicum silicate ceiling tiles of approved texture (Spintone / Cosmos/hexa) in the grid including, cutting/ making opening for services like

Chequered terrazo tiles 22 mm thick with graded marble chips of size up to 6 mm in floors, jointed with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand) :

Dark shade pigment using ordinary cement.

Providing and fixing factory made UPVC door frame made of UPVC extruded sections having an overall dimension as below (tolerance ±1mm), with wall thickness 2.0 mm (± 0.2mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturers specification and direction of Engineer-in-charge:

Extruded section profile size 48x40 mm.

Extruded section profile size 42x50 mm.

Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mm x 19mm for styles and 15x15mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture . M.S. frame covered with 5mm thick heat moulded PVC 'C' channel of size 30mm thickness, 70mm width out of which 50mm shall be flat and 20mm shall be tapered in 45degree angle on both side forming styles; and 5mm thick, 95mm wide PVC sheet out of which 75mm shall be flat and 20mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115mm wide PVC sheet out of which 75mm shall be flat and 20mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10mm (5mm x 2 ) thick, 20mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail. paneling of 5mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7mm (5mm+2mm) thick x 15mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5mm thick PVC strip of 20mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge. Manufacturer’s specification & drawing:

30 mm thick plain PVC door shutters.

30 mm thick pre laminated PVC door shutters.

Providing and fixing ISI marked oxidised M.S. pressed butt hinges with necessary screws etc. complete:

Providing and fixing ISI marked oxidised M.S. sliding door bolts with nuts and screws etc. complete :

Providing and fixing ISI marked oxidised M.S. door latches conforming to IS:5930 with screws etc. complete :

Providing and fixing ISI marked oxidised M.S. handles conforming to IS:4992 with necessary screws etc. complete:

Providing and fixing IS : 12817 marked stainless steel butt hinges with stainless steel screws etc. complete :

Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete:

Providing and fixing aluminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade with necessary screws etc. complete :

Providing and fixing aluminium handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :

Providing and fixing partition up to ceiling height consisting of G.I. frame and required board including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 gms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling

66 mm overall thickness partition using 8mm thick double skin multipurpose cement bonded wood particle board manufactured as per IS:14276 with suitable cement bonded board screws.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in (Cement shall be free issue material):

Cement mortar 1:4 (1 cement : 4 coarse sand).

Cement mortar 1:3 (1 cement : 3 coarse sand).

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level (Cement shall be free issue material):

Cement mortar 1:3 (1 cement :3 coarse sand).

Cement mortar 1:4 (1 cement :4 coarse sand).

12 mm cement plaster finished with a floating coat of neat cement of mix :

1:3 (1 cement: 3 fine sand).

1:4 (1 cement: 4 fine sand).

Centering and shuttering including strutting, propping etc. and removal of form for :

Foundations, footings, bases of columns, etc. for mass concrete.

Walls (any thickness) including attached pilasters, buttresses, plinth and string courses etc.

Columns, Pillars, Piers, Abutments, Posts and Struts.

Key/ duplicate key (of steel/ brass)for wooden/alumunium Door etc

Lock of Wooden Table/Credenja/Cabinet/ storage cabinet etc (Multipurpose locks)

Lock of Steel Almirah/ Fire hose boxes.

Lock of Steel - Table/steel Filing cabinet

Concealed Lock of Wooden door (Make- Godrej or approved equivalent)

Night latch of Godrej make or approved equivalent

Pad lock (7 Levers, with three keys) of Godrej or approved equivalent make

Conceal type door closer of Ozone/Godrej or approved equivalent

Double action Floor spring type door closer- Big size with SS cover plate

Double action Floor spring type door closer- Small size with SS cover plate

Hydraulic type door closer of Godrej make or approved equivalent

Drawer channel set alongwith movement wheel/ bearing.

Sliding door of Rack including runner & channel

Heavy type oxidised Brass/stainless steel Hinge with necessary screws for wooden door.

Hinge (full height) of Cupboard/ storage cabinet door.

Aldrop (Brass Chitkni 8")

Aldrop (Alumn. Chitkni 6")

Heavy duty double pad lacquered SS Door stopper of approved sample

Wooden knob for drawers/ cabinets etc of approved design/ make/ sample

Fancy Acrylic knob for drawer of approved make/sample

Teak wood knob (4.5" dia) for the glass doors of approved design complete works as required

Heavy duty Coat/Calendar hooks (of approved sample) as required

White Magnetic writing Board, complete as approved by EIC.

Pin-up Board of soft board, duly fixed with velvet of approved make/ colour with 6mm commercial ply backing including wood moulded beading and finished in approved melamine polish with all hardwares etc complete as required.

12 mm thick clear float toughened glass (ISI mark) of approved make complete with Etching/ Grinding etc. as required in Door panels/ partitions.

ISI Mark smoke glass of thickness 6 mm of approved make in the existing Aluminum door, windows, partitions etc with beading, clips, rubber gasket etc complete as required.

ISI Mark Table Top (5.5 mm thick) clear sheet glass of approved make including cutting, polishing, grinding, rubbing the edges etc complete as required.

Window handle/ locking arrangements for Alumn. Frame window

Window hinge (Alumn. frame)

Rubber gasket/ snap beading for glass in Alumn. Door/window, Fire Box etc.

Providing and fixing 1.5 mm thick laminate on partition/ panelling/ cup boards including the cost of adhesives / pressing etc. (The ISI Mark laminates of Century/ merino/ green or approved equivalent make in approved shade, colour and finish is required to be used )

Providing and fixing 4 mm mm thick decorative teak ply veneers of Century/ duro/ green or approved equivalent over the partitions/ panelling, making grooves including necessary adhesive, materials,hardware etc

Providing and fixing in position FRAMELESS GLASS PARTITION with 12 mm thick clear toughned glass of Saint Gobain / Pilkington / Modiguard make fixed to floor and soffit of ceiling / false ceiling rigidly and at the centres wherever required in line and level with SS patch fittings of Dorma or approved equivalent make with all enabling works complete as per drawing and direction of the engineer in charge.

Providing & fixing Livin wall paper (Danmi, Benz specification) gravure printed-pre-trimmed-washable -strippable of approved shade and design including preparation of wall surface, fixing with sutibale glue as per the manufacturer specification and as per direction of EIC. Basic rate of wall paper-Rs.849.05 per sqm"

Providing & fixing on glass panes, self-adhesive image graphics film with computerised graphic design 3MFrosted film as per design.

Providing and erecting a "W" metal beam crash barrier comprising of 3 mm thick corrugated sheet metal beam rail, 70 cm above road/ground level, fixed on ISMC series channel vertical post, 150 x 75 x 5 mm spaced 2 m centre to centre, 1.8 m high, 1.1 m below ground/road level, all steel parts and fitments to be galvanised by hot dip process, all fittings to conform to IS:1367 and IS:1364, metal beam rail to be fixed on the vertical post with a spacer of channel section 150 x 75 x 5 mm, 330 mm long complete as per clause 810 of MoRT&H specification including all material, labour machinery etc.

GI Metal Tile Lay-in Perforated Tegular edge global white color tiles of Size 595x595 mm and 0.5 mm thick

Providing and fixing PVC Laminated Gypsum Tiles (Square edge) of Size 595x595 mm and 12.5 mm thick

P/F stainless steel AISI 316 grade pull handle 25mm dia 600mm long O shape i/c making holes in glass ( Ozone / Dorset or equivalent make).

Fixing Toughened glass 12 mm thickness as door excluding handle, locks and door closer only

Supplying, fitting and fixing porcelain partition wall of approved make of size 618 mm X 310 mm complete in all respect.

Supplying, fitting & fixing Surface mounted Crash Bar/ panic Bar of touch pad style, made of heavy duty cast iron/ steel body & latches with SS, BHMA certified & conforming to ANSI A 156.3 for grade-1 (3 hours fire rated) and suitable for surface mounting to wooden/hollow metal/ Al framed door with opening upto 900mm, with maximum operating force 6 kg for unlocking easily & outwardly during emergency, complete in all respect as per direction & satisfaction of Engineer-in-Charge.

a) for door opening 900

b) for door opening 1200

Supplying, fitting & fixing Surface mounted overhead Door Closer for 2 hour fire rated doors, of size EN-4 for leaf width upto 950/ 1100mm weighing maximum 60/ 80 kgs, CE certified, marked & conforming to EN 1154-2003 of approved quality of reputed brand, complete as per direction & satisfaction of Engineer-in-Charge. for leaf width upto 1100mm

Supplying, fitting & fixing Stainless Steel 'D' or 'H' type of size 300 mm x 19 mm tubular Handle with Grade 304, CE certified, marked & conforming to EN -1154, of approved quality of reputed brand as per direction of Eingineer-in- Charge fitted and fixed complete including all incidental charges.

PROVIDING AND ANCHORING IN POSITION MECHANICAL GENERAL PURPOSE ANCHOR BOLTS (HST/HSA) OF GRADE 5.8 AND SPECIFIED DIA AND STANDARD LENGTHS INCLUDING NECESSARY DRILLING UP TO REQUIRED DEPTH, ANCHORING AND GROUTING WITH NECESSARY EQUIPMENTS ETC., COMPLETE AS PER SPECIFICATIONS OF AGENCY APPROVED BY CONSULTANTS(HILTI OR EQUIVALENT) - 10 mm dia/140 mm long or 12 mm dia/ 150 mm long

Providing and fixing 4 mm thick ACP (aluminium composite panel)

Providing & fixing YELLOW & BLACK READY MADE SPEED BREAKER made by ABS plastic of sizes 250X350X50 MM. The job includes cleaning the surface with wire brush, flling of cement concrete in side the breaker, fixing with adhesive and nailing the speed breaker with 6 to 8 mm dia steel screw complete or as per direction of Engineer in charge.

Supply & Installation of Convex Mirror, Mirror Size min 32 inch lens-Polycarbonate with Hood

"Providing and Fixing Solid SS LEVER HANDLE ON ROSE AND CYLINDER ESCUTCHEON , SS MATT(Hafele 903.92.646 or Approved equivalent) as per direction of Engineer in charge"

Providing and Fixing Surface Mounted Door Closer, (with guide rail) Hold Open Slide Arm withTrack(Dorma:TS 92 or Approved equivalent) as per direction of Engineer in charge

Providing and fixing bottle trap of make kohler (product code K-75823IN-CP) with 350mm extension tube, wall flange complete in all respects as per direction of Engineer in charge

Providing and fixing brass angle valve of make kohler model July (Product code 80154IN-4AV-CP) or approved equivalent with ESCUTCHEON complete in all respects as per direction of Engineer in charge

Providing and fixing liquid soap dispenser of approved make. Includingscrews, washers and rawl plug etc.(Make : Jaquar, Model : AKP-35735P, or ApprovedEquivalent)"

Angular Stop Cock with Wall Flange of ESSCO make,Item code APR-101053 or equivalent

Pillar Cock with Extension Body of ESSCO make,Item code APR-101021M or equivalent

Flush Cock with Wall Flange, Size: 25 mm of ESSCO make,Item code APR-101081 or equivalent

White vitreous china clay half stall urinal flat back 580x380x350 mm or angle back 450x375x350 mm with waste fittings as per IS:2556 as directed by Engieer-in-Charge.

Jet Spray with 1 Meter PVC Tube (Stainless Steel) of ESSCO make, Item code ALE-547 or equivalent

Towel Rail 600mm Long, Stainless Steel of ESSCO make, Item code AEC-1111N or equivalent

Brass 100mm mortice latch and lock with 6 levers without pair of handles

Brass mortice latch and lock 100x65mm with 6 levers and a pair of brass lever handles

Supplying Accessories for Automatic Sensor Based Products of Bharat Photon or approved equivalent make complete as per Instruction and Direction of Engineer-in-charge.

Battery Box

Classic Battery Box (Old-Lead)

Flow Control (Screw)

Braided SS Pipe (230mm)

Swivel Coupling (Small)

Sensor Plate

Transformer (AC)

Solenoid Valve (1/2") (6V DC-Brass)

Solenoid Valve (1/2") (12V DC-Teflon)

Solenoid Valve (1/2") (6V DC-Teflon)

Control Unit Sensor Tap (6V DC)

Sensor Eye Lead

Providing and Fixing Rollar Blinds AMI Make or approved make & shade of 38mm round Aluminium channel with Blackout fabric & telting with chain (Ball) system with all necessary fixtures and fitting etc. complete. (Sample to be final by Engineer In-charge prior execution of work)

Labour charges for fabricating & erecting structural steel work such as trusses, purlins, sagrods, bracings, gates or other miscellaneous fabrications in built-up section including cutting, hoisting,fixing in position, revetting, bolting and welding of joints from joists, angles, channels, flats, round bars, plates with all necessary labour & consumables like welding rods, gas and scaffoldings complete as per the directions of engineer-in-charge (Only structural steel is to be supplied by IOCL free of cost).

Dash fastener / Chemical fastener

Calcium Silicate tegular edged celling tiles 595x595 mm and 15 mm thick on edges

GI Metal Tile Lay-in Plain Tegular edge global white color tiles of Size 595x595 mm and 0.5 mm thick

GI Metal Tile Lay-in Perforated Tegular edge global white color tiles of Size 595x595 mm and 0.5 mm thick

PTMT - Waste Coupling 31/32 mm

PTMT - Waste Coupling 38/40 mm

GI/Aluminium Sheet (0.8 mm thick)

Stone tile work for wall lining up to 10 m height with special adhesive over 12mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) including pointing in white cement with an admixture of pigment to match the stone shade. 8mm thick (mirror polished and machine cut edge).

Granite stone of any colour and shade.

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge: Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Supplying & Applying various epoxy and other protective intermediate / finish paints of approved brand and manufacturer at all heights over prepared/primed surface for steel structures, pipelines, tanks, equipments, concrete floors etc. as per manufacturers specification & directions of Engineer-in-charge and; all complete including all materials, labours, tools-tackles and consumables etc but excluding Scaffolding for which payment shall be made in separate item. Note- No. of coats mentioned in the SOR items are only indicative and contractor has to achieve rquired DFT by applying more coats (if required) within the relevant SOR item rates.

Polyamido-Amine Epoxy to achive a minimum DFT of 50-60 microns ( Two or more coats of 25 -30 μ each).

High solids amine cured epoxy to achive a minimum DFT of 500 microns ( Two or more coats of 250 μ each ).

All works up to plinth level: Concrete of M30 grade with minimum cement content of 350 kg /cum

All works above plinth level up to floor V level: Concrete of M30 grade with minimum cement content of 350 kg /cum

Supply, fixing and connection of Philips/approved equivalent make LED Slim Panel Round /Square suitable for Recessed / Surface mounting made of diecast alluminium body with powder coating, acrylic diffuser with Driver as per IS: 15885 (Part 2/ Sec 13) : 2012 , operating voltaGE-Venture ranGE-Venture of 150 to 265 Volts AC, P.F > 0.9, SurGE-Venture protection: 2KV,THD<10%, with high power LED's having efficacy of > 100 lumins/watt,CCT: 3000K - 5700K, minimum CRI>70, .etc., complete including supply & fixing of lead in wire, nuts, bolts, screws etc. All complete with labour and materials as per directions of Engineer-in-Charge: 36/40W (600MMX600MM) SQUARE TYPE

Supplying and fixing 10 amps., 240volts, SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 10 amps. G-series, SP,MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet, and complete with connections, testing and commissioning etc. as required. Note: ISI marked sockets shall be used.

Wiring for light point/ fanpoint/ exhaust fan point/ call point with 1.5 sqmm FRLS PVC insulated, copper conductor cable in surface, PVC conduit as required. Job includes cost of wire, conduit with accessories, ceiling rose, MS box with phenolic laminated sheet and switches etc. as required. Note: Only ISI marked conduits, cables, switches and socket outlets shall be used. : Medium point (conduit length more than 3m but upto and including 6m)

Wiring for twin control light point with 1.5 sqmm PVC insulated, copper conductor cable in surface PVC medium duty conduit with 2 way 5/6 amps. piano type switch etc. as required. Job includes cost of wire, conduit with accessories, ceiling rose, MS box with phenolic laminated sheet and switches etc. as required. Note: Only ISI marked conduits, cables, switches and socket outlets shall be used.

SUPPLY & FIXING OF MISC FIXTURES INCLUDING PERPEX SHEET Supplying and fixing below given (nominal size) metal boxes on surface or in recess with suitable size phenolic laminated sheet cover in the front including providing and fixing 3 pin 5/6 amps socket outlet and 5/6 amps tumbler/piano type switch, connections, painting etc. as required. (For light plugs).

Metal box light plug of 180 mm x 100 mm x 60 mm with 3 pin 5/6amps. Switch socket

Metal box light plug of 180 mm x 100 mm x 60 mm with 3 pin 15/16 amps. switch socket

REWINDING OF MOTORS: Rewinding of 1-phase/3-phase electrical motors of various voltage grades/makes/types and of following capacities as per the original specifications & types/gauge of rewinding/winding wire, insulation of various points inside slots/overhang and overall final layers of insulation/tapes as per the original motor specifications, after baking to required temperature and applying insulating varnish (Dr-Beck & Co. make & type), providing glass/other types of sleaves on connection wires from inside motor winding to connection plate. The winding, varnishing, tapes and other materials required for completion of this complete job is in the scope of contractor excluding transportation to & from Owner’s works to Contractor's rewinding shop. which shall be paid seperately on trip basis.The winding wire will be Devi Dayal make and insulation tapes shall be ISI marked & of reputed manufacturers as per decision of Engineer-in- Charge. This also includes repair/replacement of connection plate completely including insulating sheet, nuts, bolts, washers and other hardwares as per original specifications. This further includes replacement of bearings (DE & NDE) of SKF make & greasing (IOC/HP make Servogem 2 or equivalent). This further includes satisfactory trial of motors at Owner’s premises at No load as well as at Full load. The Contractor will guarantee the rewound motors for satisfactory performance for a period of minimum six months at owner’s premises & if any such rewound motor fails within six months, it is to be rewound again by Contractor free of cost. All complete with labour and materials as per directions of Engineer-in-Charge.Note: Burnt winding wire shall be kept by Contractor.

Motors upto & including 1.5 KW

Motors above 1.5 KW but upto including 3.7KW

Motors above 3.7 KW but upto including 7.5KW

Motors above 7.5 KW but upto including 11 KW

Gas charging of air conditioner upto 1.5ton capacity with job involved transportation of machine to vendors' works. Checking of all components for leak by charging co2 gas & finally evacuating the compressor completely & charges of refrigerant gas - R22/R32/R134A or any other

Lifting, Shifting, Positioning, Installation Testing and commissioning of indoor unit for Hi Wall Split AC 1.0TR-2.0TR including all required accessories etc complete.,

INSULATING MATS - Supply & installation and of thickness as mentioned below, approved quality insulating Elastomer mats as per specifications:Insulating Elastomer mats conforming to IS 15652:2006 of thickness 3 mm (Class A)

Replacement of outdoor fan motor of 1.5/2 ton split AC

Replacement of indoor fan motor of 1.5/2 ton split AC

Supply and Installation of AC outlet drain pipe

ADDITIONAL COPPER TUBE FOR SPLIT AC: Supply & fixing of additional length of copper tube for split A/C commissioning including all accessories.

REPLACEMENT OF CONDENSER/ COOLING COILS OF WINDOW/ SPLIT AC Supply, fixing, gas charging, testing and commissioning of following condenser or cooling coils suitable for different make & different capacity window air conditioner. Job includes dismantling of old damaged condenser/cooling coil, supply & fixing new condenser/cooling coil, gas charging, testing & commissioning. Job complete in allrespect with men & material including refrigerant gas R-22 and as per direction and instruction of site engineer/Engineer-in-Charge. NOTE : Old damaged condenser/cooling coil shall be retained by the department.

Condensor Coil Complete

Cooling Coil Complete

Removing burnt/ unserviceable compressor from the unit, replacing each with a new compressor of same make in lieu of old unserviceable one (compressor make to be approved by EIC)

ITC OF EXHAUST FAN: Installation, testing, replacement with damaged one and commissioning of exhaust fans of following sweeps including making the hole to suit the size of the above fan, making good the damage, connections, testing, commissioning etc. as required.

Exhaust fan upto 450 mm sweep

Exhaust fan more then 450 mm but upto 510 mm sweep

Supply, installation, testing and commissioning of single phase, Fresh Air Fans / Heavy duty Exhaust Fans of Bajaj/ Crompton Greaves/ Khaitan/ Usha make only including supply and fixing with all necessary supports All complete with labour and materials as per drawings, specifications and directions of Engineer-in-Charge. Note: Necessary civil works required for fixing the exhaust fans shall be in the scope of Contractor.

Fresh Air Fan with Louver Shutter 300MM sweep

Fresh Air Fan with Louver Shutter 400MM sweep

Supply, installation, testing and commissioning of Wall Mounted Fans of Bajaj/ Crompton Greaves/ Khaitan/ Usha make only including supply and fixing of the electronic regulators with all necessary supports. Also replacement of damaged on with new one. All complete with labour and materials as per drawings, specifications and directions of Engineer-in-Charge.. NOTE: Necessary civil works required for fixing the exhaust fans shall be in the scope of Contractor

OSC. Wall & cabin fans of 300MM Sweep

Supply, installation, testing and commissioning of ceiling fans of Bajaj/ Crompton Greaves/Khaitan/Usha make only including supply and fixing of the electronic regulators with all necessary supports. All complete with labour and materials as per drawings, specifications and directions of Engineer-in-Charge.

1200 MM Sweep (White)

Rewinding of ceiling/pedestal/exhaust/air circulator fans of all types/sizes/make including 1-phase and 3-phase type exhaust fans max. upto 2.2 KW capacity and supply of super enameled winding wire (Devi Dayal make, ISI marked insulation materials required). Replacement of damaged one with new one. This also includes replacement of single/double bearing SKF make/bushes (as per original make) and overhauling of fan and all jobs related to complete this work in totality. This also includes removal of fans from site, installation and commissioning after testing of rewound fans and replacement of condenser, if required. This also includes transportation from site after dismantling to Contractor’s workshop and back to site. Note: Contractor has to give guarantee for rewinding of above items for a period of six months and if winding is burnt again within six months of working of fans, it has to be rewound again free of cost of Contractor. The burnt winding shall be kept by Contractor.

Ceiling/pedestal fans

Exhaust/air circulators fans

Removing from the unit the burnt unserviceable compressor and replacing with new compressor as under in lieu of cut opened compressor and fitted back in the unit

sealed compressor for any type of 2.0 T AC

sealed compressor for any type of 1.5 T AC

Replacement of capillary tubes

Rewinding of fan motor with super enameled copper with proper gauge of wire as under

For 2.0 Ton A/C

For 1.5 Ton A/C

Replacement of brushes for fan motor

Replacement of motor shaft

Replacement of mounting rubber bushes

Replacement of over load protector of approved make as per EIC.

Replacement of box type relay of approved make as per EIC

Replacement of starting capacitor of make Usha/ Tesla/ Keltron /KFIL 36MFD

Replacement of running capacitor of make Usha/ Tesla/ Keltron / KFIL 36MFD

Replacement of fan motor capacitor 6 MFD

Rotary type

Piano / Push button type

Replacement of Thermo switch (Danfoss/Ranutrol)

Replacement of complete wiring

Replacement of blower fan from evaporator

Replacement of blade for conductor

Replacement of 3 core copper cable 3 meter length

Replacement of thermostat knob

Complete painting of the AC unit with 2 coats of spray paint or enamel paint after cleaning servicing including cleaning with caustic soda wash evaporating and conderser coil

Gas charging the system after flushing, vacuumising and dehydration as per standards including testing and detecting any leakage and arresting the same

For 2.0 Ton AC

For 1.5 Ton AC

Repair required to water cooler of Voltas/bluestar make of 150 liters & 80 liters storing capacity including collection from site and reinstallation after complete testing of equipment at site as directed by EIC/Site Enginner after carrying out either of following repairs.

Removing burnt/ unserviceable compressor from the unit, replacing each with a new compressor of same make in lieu of old unserviceable one (compressor make to be approved by EIC)

Replacing the strainer

Rewinding of the condenser fan motor with super enameled copper wire.

Replacement of the capillary tubes

Replacement of bushes for condenser fan motor with super enameled copper wire.

Replacement of rubber bushes for blower motor.

Replacement of open type relay

Replacement of starting capacitor 60 MFD/ 80 MFD (Usha/ Tesla/ Keltron make)

Supply of thermostat suitable for water cooler, window type rac whenever require as per direction of site engineer / engineer-in-charge.

Replacement of complete wiring kit

Replacement of brass float valve 15mm

Replacement of condenser coil

Replacement of complete rubber gasket

Replacement of fan blades

Replacement of complete insulation around tank

Replacement of water dispensers.

Replacement of swing motor

REMOTE CONTROL SWITCH FOR SPLIT AC :Supply & fixing of remote control switch pendant type for temperature controlling of the Voltas/Amtrex/ Fedders Lloyds/ Carrier Aircon or any other make, split air conditioners of 2.0/3.0 (2x1.5 TR) TR capacity. Job includes dismantling of the defective switches and wire and installation of new switch. Job complete in all respect including man and material and as per the directions of Engineer-in-Charge.

SIC of DB with RCBO 16 Amp, 2 pole,

SIC of DB with RCBO 20 Amp, 2 pole

SIC of DB with RCBO 32 Amp, 2 pole

OVERHAULING OF WINDOW AC, SPLIT AC, WATER COOLER ETC.

SERVICING/LEVELING/OVER HAULING/GREASING INCL. LABOUR CHARGES FOR ALL TYPES OF CHAIRS.

Dry/Wet cleaning of Revolving and Visitor Chairs

Replacement of seat assembling

Change of tepestry-seat/back

Change of base plate

Change of connecting plate

Hardware packets big for executive chair/revolving(godrej

PROVIDING & FIXING PU (POLYTHENE FOAM), HANDLES FOR CHAIRS INCL FIXTERS, FASTENING, LABOUR CHARGES ETC. (RATE PER PAIR) FOR ALL TYPES OF CHAIRS

PROVIDING & FIXING CASTOR WHEEL WITH INCL. LABOUR CHARGES FOR ALL TYPES OF CHAIRS, TABLES

PROVIDING & FIXING GAS LIFT (HYDRAULIC CYLINDER COMPLETE ASSEMBLY WITHFIXURES & FASTENING INCL. LABOUR CHARGES ETC. FOR ALL TYPES OF CHAIRS)

Replacement of chair base of Revolving Chair. Supply and fitting of Godrej orequivalent as per the chair base with wheel caster (best quality) of Revolving Chair. Job complete in all respects.

Replacement of chair bracket below seat. Supply and fitting of chairbracket in Revolving Chair. Job complete in all respects.

Replacement of visitor chair cushion seat or back.Supply and fitting of cushioned seat or back of revolving chair. Job complete in all respectsincluding supply of accessories and Hardwares.

Welding charges per chair

Providing & fixing of locks for almirah

Duplicate key for almirah

Duplicate keys for lockers & file cabinet

Duplicate key for tables and book case

Supply of table top glass-12 mm thick

SERVICING/LEVELING/OVER HAULING/GREASING INCL. LABOUR CHARGES FOR HINGEDDOOR UNIT (ALMIRAH)

Dry cleaning of sofasets (per seat for all single/double/triple seater sofas)-upholstery(silk/leather/velvet/synthetic etc.) using Tasky-R2/Partek-P2 solution/spotters & then using Tasky-R4/Partek-P4(for shineup the sofa,wherever required)as per the quality of sofa upholstery including the consumables, top quality chemicals, compounds, machines, tools & tackles, labour, material etc.duly removing all dust/dirt/stains by brushing ,vaccuming,shampooing with upholstery scrubbing brush etc. as per site requirement and complete in all respects and to the satisfaction of Engineer-In-Charge.The works will be carried out during odd- hours/Night-Hours/Holidays/Closed-Days etc. and shall include shifting of items/furnitures etc. at work-site and all jobs as per directions of Engineer-In-charge.

Please Enable Macros to View BoQ information