Repair Renovation and Addition Alteation of Judges Quarters at Poonch.

Amount

Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 meters lead : Of area of 3 sqm.and below

Demolishing brick work manually/by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 meters lead as per direction of Engineer-in-charge: In cement mortar

Dismantling wooden boardings in lining of walls and partitions, excluding supporting members but including stacking within 50 meters lead : Thickness above 25 mm upto 40 mm.

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 meters lead. For thickness of tiles above 25 mm and upto 40 mm

Dismantling old plaster or skirting, raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 meters lead. h to the dumping ground within 50 meters lead.

Demolishing cement concrete manually/by mechanical means including disposal of material within 50 meters lead as per direction of Engineer-in- charge: 1:3:6 or richer mix (i/c equivalent design mix)

Earth work in excavation by manual means in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed 25 meter beyond 1 m from cutting edge: All kinds of soil

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering . All work up to plinth level with : 1:5:10 ( 1 cement :5 coarse sand :10 graded stone aggregate 40 mm nominal size )

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering .All work up to plinth level with : 1:3:6 with ( 1 cement : 3 coarse sand :6 graded stone aggregate 20 mm nominal size).With 20% stone

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering .All work up to plinth level with : 1:3:6 with ( 1 cement : 3 coarse sand :6 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering .All work up to plinth level with : 1:2:4 with ( 1 cement : 2 coarse sand :4 graded stone aggregate 20 mm nominal size)

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in Super structure: Cement mortar 1:6 ( 1 cement : 6 coarse sand)

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or with dash fasteners shall be paid for separately):Sal wood

Providing and fixing 35mm thick panelled or panelled and glazed shutters for doors,windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note: -Butt hinges and necessary screws shall be paid separately). First Class Kail - Wood .

Providing and fixing 30mm thick wire gauze shutters using galvanized M.S. wire gauze of average width for aperture 1.4 mm in both directions with wire of dia. 0.63 mm for doors, windows and clerestory windows with ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws as per direction of Engineer-in-charge : First class kail wood

Providing and fixing 35mm thick glazed shutters for doors, windows and clerestory windows using 4mm thick float glass panes including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. First class kail wood

Providing and fixing 12 mm thick flat pressed 3 layer medium density particle board or graded particle board (Grade I) IS: 3087 marked, in ceiling with necessary nails etc. complete (frame work to be paid separately) :

Providing and fixing wooden moulded beading to door and window frames with iron screws,plugs and priming coat on unexposed surface etc. complete 50x12mm

Reinforced cement concrete work in beams, suspended floors, roofs having slope upto 15°, landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases upto five level including curing but excluding the cost of centring, shuttering, finishing and reinforcement with 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Mild steel and medium tensile steel bars

Centring and shuttering including strutting propping etc. and removal of form for :-

Foundations, footings, bases of columns etc. for mass concrete.

Walls (any thickness) including attached pilasters,buttreses,plinth and string courses etc.

Suspended floors, roofs, landings, balconies and access platforms.

Edges of slabs and breaks in floors and walls Under 20 cm wide

6 mm cement plaster to ceiling of mix 1 : 3 (1 cement : 3 fine sand)

12mm Cement plaster of mix: 1 : 6 ( 1 cement : 6 coarse sand)

Repairs to plaster of thickness 12mm to 20 mm in patches of area 2.5 sq. meters and under, including cutting the patch in proper shape raking out joints and preparing and plastering the surface of the walls complete including disposal of rubbish to the dumping ground within 50 meters lead: With cement mortar 1:4 (1 cement: 4 fine sand)

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622) of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement :4 coarse sand), including grouting the joints with white cement and matching pigment etc. complete size of tile 600x600mm

Providing and laying Ceramic glazed floor tiles 300x300 mm (thickness to be specified by the manufacturers) of 1st quality conforming to IS: 15622 of approved make, laid on 20 mm thick bed of cement mortar 1: 4 ( 1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigment etc., complete. In colour such as White, Ivory, Grey, Fume Red Brown

Providing and fixing of 12mm thick marine/water proof ply for ceiling including cutting hosting and fixing position and painting with primer and enamel paint.

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete.

Painting on G.S sheets with synthetic enamel paint of approved band and manufacture of required colour to give an even shade on New work (two or more coats) including a coat of approved steel primer but excluding a coat of mordant solution.

Finishing walls with premium Acrylic smooth exterior paint with silicon additives of required shade: Old work (Two or more coats applied @ 1.43 liters/ 10 sqm) over existing cement paint surface.

Applying priming coat With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood).

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade Two or more coats on new work

Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber / neoprene gasket felt etc. Aluminum sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge (glazing, panelling and dash fasteners to be paid for separately.) Polyester powder coated aluminum (minimum thickness of polyester powder coated 50 microns)

For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately.) Powder coated aluminum (minimum thickness of powder coated 50 microns)

Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board (conforming to IS: 12823 Grade-I type-II) in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in- charge. Pre-laminated particle board with decorative lamination on both sides.

Providing and fixing glazing in aluminum door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer- in-charge. (Cost of aluminum snap beading shall be paid in basic item.) With floating glass panes of 4.0 mm thickness (weight not less than 10.00 kg / sqm)

Providing and fixing aluminum tubular handle bar 32mm outer dia, 3.0mm thick & 2100mm long with SS screw etc. complete as per direction of Engineer-in-charge. Polyester powder coated minimum thickness 50 micron aluminum tubular handle bar

Providing and Fixing Two Seater Sofa

Providing and Fixing Chair

Providing and fixing cupboard shutters 25mm thick, with pre-laminated flat pressed three layer particle board or graded wood particle board IS: 12823 marked exterior grade (Grade I Type II) having one side decorative lamination and other side a balancing lamination including second class teak wood lipping of 25mm widex12mm thick with necessary screws and bright finished stainless steel piano hinges complete as per directions of Engineer- in-charge

Renewing glass panes and re-fixing existing wooden fillets: Float glass panes of thickness 5.0 mm (weight not less than 12.5 kg/sqm)

Providing and Fixing of PVC Laminates for PVC panelling of approved quality and make including cutting,hoisting & fixing in poistion etc including all necessary fixing accessories etc all complete job for walls & ceiling

For Walls

For Ceiling

Labour engaged for removal of vegetation cuting of grass & removal of mulba and its disposal etc complete job.

Removaing glas panes with wooden fillets/putty & nails fittings

Providing and fixing aluminum tower bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete :

Providing and fixing aluminum handles ISI marked anodized (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete.

Providing and fixing aluminum sliding door bolts ISI marked anodized (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with nuts and screws etc. complete :

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous chuna flushing cistern and CP flush bend with fittings and C.I.brackets 40mm flush bend, over flow arrangement with special of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets cutting and making good the walls wherever required: WC pan with ISI marked with solid plastic seat and lid .

Providing and fixing wash basin with C.I brackets, 15mm C.P.brass pillar taps, 32mm C.P. brass waste of standard pattern, including painting of fittings and brackets,cutting and making good the walls wherever required: White vitreous china wash basin size 550x400mm with a pair of 15mm C.P. brass pillar taps.

Providing and fixing PVC low level flushing cistirn manually cotoral device (Handle lever) with all fitting and fixitures complete 10 liter capacity coloured .

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x410x265mm size respectively with automatic flushing cistern with standard flush pipe and C.P brass spreaders with brass union and G.I clamps complete,including painting of fitting and brackets ,cutting and making good the walls and floors wherever required: One urinal basin with 5 litre white PVC automatic flushing cistern

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6mm thick hard board backing. Rectangular shape 453 x 357mm (outer dimensions).

Providing and fixing PTMT towel ring trapezoidal shape 215 mm long , 200 mm wide with a minimum distance of 37 mm from wall face with concealed fittings arrangements of approved quality and colour , weighing not less than 88 gms

Providing and fixing of PVC Water Tank of approved Quality

Providing and fixing G.I pipes complete with G.I fittings and clamps,including cutting and making good the walls etc. INTERNAL WORK-Exposed on wall 15 mm dia nominal bore ,Medium

Providing and fixing waste pipe fro sink or wash basin including PVC waste pipe fitting complete 40mm dia

Dismantling roofing including ridges,hips valleys and gutters etc. and stacking the material within 50 meters lead of:G.S.Sheet

Providing corrugated G.S. Sheet roffing including vertical / curved surfaces fixed with polymer coated J or L hooks , bolts and nuts 8mm dia limpet and bittumen and G. I . limpet washers or with G.I. limpet washer filled with white lead and including a coat of approved steel primer and two coats of approved paint on over lapping of sheets complete (up to any pitch in horizontal/vertical orcurved surface ) excluding the cost of purlin , rafter and trusses and including cutting to size and shape whereever required. 0.63 mm thick with zinc coated not less than 275 gm/sqm.

providing ridges or hips of width 60cm overall width plain G.S. sheets fixed with polymer coated J or L hooks ,bolts and nuts 8mm dia G.I limpet and bitumen washers complete . 0.63mm thick zinc coating not less then 275 gm /sqm

SHRI MOHD SAQIB MALIK

SHAZAD SHABNAM

TARANJEET SINGH RISSAM