Construction of Coimbatore Chapter building located at Door Nos 129-135, Nehru Street, Ramnagar, Coimbatore, Tamilnadu

BILL OF QUANTITIES (BOQ) -SUMMERY SHEET

Construction of Coimbatore Chapter building located at Door Nos 129-135, Nehru Street,

Ramnagar, Coimbatore, Tamilnadu

DSR 2023 AMOUNT

DSR- DSR 2025 NDSR

Including correction

S.No.2023/2025/N DESCRIPTION AMOUNT AMOUNT (in

factor @0.973 and

DSR (in Rs) Rs)

COST INDEX @22%

6.00 GRAND TOTAL 32,495,571

6.00 GRAND TOTAL 32,495,571

Digitally signed by DEEPAK

ESTIMATE FOR CIVIL WORKS

DSR ITEM correction NDSR DSR 2023

SL. NO UNIT QUANTITY NDSR AMOUNT

NO factor RATE AMOUNT

SH-2 EXCAVATION WORKS

Earth work in excavation by mechanical means (Hydraulic excavator) /

manual means foundation trenches or drains (not exceeding 1.5 m in

width or 10 sqm on plan), including dressing of sides and ramming of

1 2.8.1 bottoms, for all lift, including getting out the excavated soil and disposal of cum 630 309 194670

surplus excavated soil as directed, within a lead of 50 m.

Extra for every additional lift of 1.5 m or part thereof in excavation / banking

2 2.26.1 excavated or stacked materials. All kinds of soil cum 360 150.5 54180

Filling available excavated earth (excluding rock) in trenches, plinth, sides

of foundations etc. in layers not exceeding 20cm in depth, consolidating

each deposited layer by ramming and watering, lead up to 50 and for all lift.

3 2.25 All kinds of soil cum 350 232.7 81445

Earthwork is disposal upto 5km By Mechanlcal Transport lncludlng

4 1.1.2 loadlng,unloadlng and stacking sqm 100.00 387.8 38780

Open timbering over areas including strutting, shoring etc. complete.

(Measurements to be taken of the face area timbered): Depth exceeding 3

m but not exceeding 4.5 m

Supplying and filling in plinth with sand under floors, including watering,

6 2.27 ramming consolidating and dressing complete cum 1.00 2521 2521

Supplying chemical emulsion in sealed containers including delivery as

7 2.34 specified

Chlorpyriphos/ Lindane emulsifiable concentrate of 20%

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL

9 2.35 anti-termite treatment (excluding the cost of chemical emulsion) :

Treatment of soil under existing floors using chemical emulsion @ one litre

per hole, 300 mm apart including drilling 12 mm diameter holes and

10 2.35.3 plugging with cement mortar 1 :2 (1cement : 2 Coarse sand) to match the

existing floor:

With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

SH-4 CONCRETE WORK

Providing and laying in position cement concrete of specified grade

excluding the cost of centering and shuttering-

Allworkuptoplinthlevel:1:4:8(1Cement:4 coarsesand(zone-III)derived from

12 4.1.8 natural sources :8 graded stoneaggregate 40 mm nominal size derived cum 83.00 8086 671138

from natural sources)

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement :

3 coarse sand (zone-III) derived from natural sources : 6 graded stone

aggregate 20 mm nominal size derived from natural sources) over 75mm

thick bed of dry brick ballast 40 mm nominal size, well rammed and

13 4.17 consolidated and grouted with fine sand, including necessary excavation, sqm 320.00 889.5 284640

levelling & dressing & finishing the top smooth.

Providing & applying a coat of residual petroleum bitumen of grade of VG-

10 of approved quality using 1.7 kg per square metre on damp proof

14 4.13 course after cleaning the surface with brushes and finally with a piece of sqm 50.00 173.5 8675

cloth lightly soaked in kerosene oil.

Providing and laying cement concrete in retaining walls, return walls, walls

(any thickness) including attached pilasters, columns, piers, abutments,

pillars, posts, struts, buttresses, string or lacing courses, parapets, coping,

bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to

15 4.2.3 floor five level, excluding the cost of centering, shuttering and finishing: cum 14.00 11746 164444

1 :2:4 (1 Cement : 2 coarse sand (zone-Ill) derived from natural sources : 4

graded stone aggregate 20 mm nominal size derived from natural sources)

Providing and laying damp-proof course 40mm thick with cement

concrete1:2:4 (1cement:2 coarse sand (zone-III):4graded stone aggregate

SH- 5 REINFORCED CEMENT CONCRETE

Digitally signed by DEEPAK

Providing and laying in position ready mixed M-30 grade concrete for reinforced

cement concrete work, using cement content as per approved design mix,

manufactured in fully automatic batching plant and transported to site of work in

transit mixer for all leads, having continuous agitated mixer, manufactured as per

mix design of specified grade for reinforced cement concretProviding and laying

in position ready mixed or site batched design mix cement concrete for reinforced

cement concrete work; using coarse aggregate and fine aggregate derived from

natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement,

admixtures in recommended proportions as per IS: 9103 to accelerate / retard

setting of concrete, to improve durability and workability without impairing

strength; including pumping of concrete to site of laying, curing, carriage for all

leads; but excluding the cost of centering, shuttering, finishing and reinforcement

as per direction of the engineer-in-charge; for the following grades of concrete.

Note: Extra cement up to 10% of the minimum specified cement content in design

mix shall be payable sperately. In case of the cement content in design mix is

more than 1:10 times of the specified minimum cement content , the contractor

shall have discussion to either re-design the mix or bear the cost of extra cement.

Digitally signed by DEEPAK

All works upto plinth level concrete M30 grade with minimum cement

Providing and laying in position ready mixed M-30 grade concrete for reinforced

cement concrete work, using cement content as per approved design mix,

manufactured in fully automatic batching plant and transported to site of work in

transit mixer for all leads, having continuous agitated mixer, manufactured as per

mix design of specified grade for reinforced cement concretProviding and laying

in position ready mixed or site batched design mix cement concrete for reinforced

cement concrete work; using coarse aggregate and fine aggregate derived from

natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement,

admixtures in recommended proportions as per IS: 9103 to accelerate / retard

setting of concrete, to improve durability and workability without impairing

strength; including pumping of concrete to site of laying, curing, carriage for all

18 5.33 leads; but excluding the cost of centering, shuttering, finishing and reinforcement

as per direction of the engineer-in-charge; for the following grades of concrete.

Note: Extra cement up to 10% of the minimum specified cement content in design

mix shall be payable sperately. In case of the cement content in design mix is

more than 1:10 times of the specified minimum cement content , the contractor

shall have discussion to either re-design the mix or bear the cost of extra cement.

All works above plinth level upto floor V level concrete M30 grade with

5.33.2.2 minimum cement content of 350kg/cum 260 11884 3089840

Providing and laying design mix cement concrete of M-30 grade, in roads/ taxi

tracks/ runways, using cement content as per design mix, using coarse sand and

graded stone aggregate of 40 mm nominal size in appropriate proportions as per

approved & specified design criteria,

providing dowel bars with sleeve/ tie bars wherever required, laying at site,

spreading and compacting mechanically by using needle and surface vibrators,

levelling to required slope/camber, finishing with required texture, including steel

form work with sturdy M.S. channel sections, curing, making provision for

contraction/ expansion, construction & longitudinal joints (10 mm wide x 50 mm

19 16.43 deep) by groove cutting machine, providing and filling joints with approved joint

filler and sealants, complete all as per direction of Engineer-in-charge (Item of

joint fillers, sealants, dowel bars with sleeve/ tie bars to be paid separately). Note:-

Cement content considered in M-30 is @ 340 kg/cum. Excess/ less cement used as

per design mix is payable/ recoverable separately.

Cement concrete prepared with batch mixing machine

Centering and shuttering including strutting, propping etc. and removal of form for

a 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete sqm 140.00 65170

Walls (any thickness) including attached pilasters, butteresses, plinth and string

c 5.9.3 Suspended floors, roofs, landings, balconies and access platform sqm 895.00 985395

d 5.9.4 Shelves (Cast in situ) sqm 2.00 2202

e 5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers sqm 1005.00 878571

f 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts sqm 380.00 433580

g 5.9.7 Stairs, (excluding landings) except spiral-staircases sqm 25.00 22700

h 5.9.16.1 Edges of slabs and breaks in floors and walls - Under 20 cm wide metre 260.00 64376

i 5.9.19 Weather shed, Chajjas, corbels etc., including edges sqm 33.00 37257

Steel reinforcement for R.C.C. work including straightening, cutting, bending,

placing in position and binding all complete up to plinth level and above plinth

21 5.22A.6 level. Thermo-Mechanically Treated bars of grade Fe-500D or more. Kg 55000.00 127.1 6990500

Digitally signed by DEEPAK

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C.

22 5.30 projections. metre 480.00 44673.6

SH-6 BRICK WORK

Brick work with common burnt clay F.P.S. (non modular) bricks of class

23 6.1.2 designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 cum 2.00 16932

coarse sand) 8466

Brick work with common burnt clay F.P.S. (non modular) bricks of class

designation 7.5 in superstructure above plinth level up to floor V level in all shapes

24 6.4.2 and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand) cum 150.00 1621350

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class

designation 7.5 in superstructure above plinth level up to floor V level. Cement

25 6.13.2 mortar 1:4 (1 cement :4 coarse sand) sqm 63.00 84042

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every

26 6.15 third course of half brick masonry. sqm 63.00 7837.2

SH-8 CLADDING WORK

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622

(thickness to be specified by the manufacturer), of approved make, in all colours,

shades except burgundy, bottle green, black of any size as approved by Engineer-

in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement

27 8.31 mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ sqm 250.00 1505 376250

3.3kg per sqm, including pointing in white cement mixed with pigment of

matching shade complete.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and

prepolished, machine cut for kitchen platforms, vanity counters, window sills,

facias and similar locations of required size, approved shade, colour and texture

laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints

treated with white cement, mixed with matching pigment, epoxy touch ups,

28 8.2 including rubbing, curing, moulding and polishing of edges to give high gloss

finish etc. complete at all levels.

Area of slab over 0.50 sqm

SH-9 UPVC AND FRP WORK

Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of

lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required)

extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2

profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any

shape, colour and design duly reinforced with galvanized mild steel section made of

required shape & size as per CPWD Specification, uPVC extruded glazing beads,

interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM

gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head,

comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as

per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws

etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion

welded/mechanically jointed duly sealed at all corners, including drilling of holes for

fixing hardware and drainage of water etc. After fixing frame the gap between frame and

adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of

approved size and quality, all complete as per approved drawing conforming to CPWD

specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross

29 9.147.A sections of uPVC profiles to be as per design approved by Engineer-in-Charge Wire

mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high

performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231

shall be paid separately.

Note:- Structural design proof checked from a Government Engineering Institute, to be

provided by the manufacturer for : (i) Sites with basic wind speed > 45 m/sec as per IS

(ii) Sites with structure height more than 20m for all wind speeds

Three track panels sliding door wit hAluminium channel for roller track,wool

pile,zincalloy(zamak) powder coated handle on two panels along with multi-point

locking system,adjustable nylon rollers with SS 304 body. Using R3 series with

9.147.B4.1 frame(98mm&above)x(40mm&above)& sach(30mm&above)x(74 mm & above). sqm 112.00 9837 1101744

(Height upto 2.5 metre).

Providing wood work in frames of doors, windows, clerestory windows and other

frames, wrought framed and fixed in position with hold fast lugs or with dash

30 9.1.1 fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for cum 0.64 169690 108601.60

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain

in gloss / matt/ suede finish with high density protective surface layer and reverse

31 9.127.2 side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of sqm 32.00 1065.15 34084.8

adhesive of approved quality 1.0 mm thick

Providing 40x5 mm flat iron hold fast 400 mm long including fixing to frame with

10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete

32 9.53 block 300x100x150mm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone No 206.00 271.66 55961.96

aggregate 20mm nominal size).

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating

33 9.97 not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour 0

or shade, with necessary screws etc. complete :

Digitally signed by DEEPAK

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not

less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or

shade, with necessary grade AC 10 as per IS : 1868) transparent or dyed to

34 9.100.1 required colour or shade, with necessary screws etc. complete : No 22.00 78.64 1730.08

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised

(anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to

35 9.101.2 required colour and shade, with necessary screws etc. complete. Twin rubber No 22.00 85.88 1889.36

Providing and fixing aluminium extruded section body tubular type universal

hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the

36 9.84 body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), No 22.00 1167.06 25675.32

with double speed adjustment with necessary accessories and screws etc. complete

Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-

section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter

of 30 mm thickness. The laminate shall be moulded with fire resistant grade

unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm

34 9.121 thick and shall be filled with suitable wooden block in all the three legs. The frame metre 73.00 677.75 49475.75

shall be covered with fiber glass from all sides. M.S. stay shall be provided at the

bottom to steady the frame.

Providing and fixing to existing door frames.30 mm thick Glass Fibre Reinforced

Plastic (FRP) panelled door shutter of required colour and approved brand and

manufacture, made with fire - retardant grade unsaturated polyester resin, moulded

to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden

38 9.122.1 frame and suitable blocks of seasoned wood inside at required places for fixing of sqm 21.00 4416.75 92751.75

fittings, cast monolithically with 5 mm thick FRP laminate for panels conforming

to IS: 14856, including fixing to frames.

SH-10 STEEL WORK

Steel work welded in built up sections/ framed work, including cutting, hoisting,

fixing in position and applying a priming coat of approved steel primer using

37 10.25.2 structural steel etc. required. In gratings, frames, guard bar, ladder, railings, Kg 300.00 204.89 61467

brackets, gates and similar works

Providing and fixing in position collapsible steel shutters with vertical channels

20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and

bottom rail of T-iron 40x40x6mm, with 40 mm dia steel pulleys, complete with

38 10.3 bolts, nuts, locking arrangement, stoppers,handles, including applying a priming sqm 4.58 13579.5 62194.11

coat of approved steel primer

Providing and fixing M.S. grills of required pattern in frames of windows etc. with

M.S. flats,square or round bars etc. including priming coat with approved steel

39 9.48.2 primer all complete. Fixed to openings /wooden frames with rawl plugs screws etc Kg 500.00 282.94 141470

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle

iron and 3mm M.S. gusset plates at the junctions and corners, all necessary fittings

complete, including applying a priming coat of approved steel primer. Using M.S.

40 10.5.1 angels 40x40x6 mm for diagonal braces sqm 2.00 6890.11 13780.22

SH-11 FLOORING WORK

Providing and laying flamed finish Granite stone flooring in required design and

patterns,in linear as well as curvilinear portions of the building all complete as per

the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick

base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement

slurry and pointing with white cement slurry admixed with pigment of matching

41 11.55.1 shade including rubbing, curing and polishing etc. all complete as specified and as sqm 2.00 3782.8 7565.6

directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black,

Cherry Red, Elite Brown, Cat Eye or equivalent

Providing and laying Vitrified tiles in floor in different sizes (thickness to be

specified by the manufacturer) with water absorption less than 0.08% and

conforming to IS:15622, of approved brand & manufacturer, in all colours and

shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing

with grey cement slurry @3.3 kg/sqm including grouting the joints with white

cement and matching pigments etc. The tiles must be cut with the zero chipping

diamond cutter only . Laying of tiles will be done with the notch trowel, plier,

wedge, clips of required thickness, leveling system and rubber mallet for placing

the tiles gently and easily.

11.41A.1.3 Double charge vitrified tile polished finish of size 600 x 1200 mm sqm 350.00 1872.17 655259.5

Providing and laying Vitrified tiles in floor in different sizes (thickness to be

specified by the manufacturer) with water absorption less than 0.08% and

conforming to IS:15622, of approved brand & manufacturer, in all colours and

shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing

with grey cement slurry @3.3 kg/sqm including grouting the joints with white

cement and matching pigments etc. The tiles must be cut with the zero chipping

43 11.41A.3.1 diamond cutter only . Laying of tiles will be done with the notch trowel, plier, sqm 55.00 1738.86 95637.3

wedge, clips of required thickness, leveling system and rubber mallet for placing

the tiles gently and easily.Glazed Vitrified tiles Matt/Antiskid finish of size

Digitally signed by DEEPAK

Providing and laying 60mm thick faciory made cement concrete interlocking paver

block of M -30 grade made by block making machine with strong vibratory

compaction, of approved size,design & shape, laid in required colour and pattern

over and including 50mm thick compacted bed of coarse sand, filling the joints

44 16.68 with line sand etc. all complete as per the direction of Engineer-in-charge. sqm 380.00 1152.64 438003.2

SH-13 FINISHING WORK

12 mm cement plaster of mix : 1:6 (1 cement: 6 coarse sand)

46 13.4.1 12 mm cement plaster of mix : 1:4 (1 cement: 4 coarse sand) sqm 776.00 424.2 329179.2

20 mm cement plaster 1:2 (1 cement : 2 stone dust).

Distempering with 1st quality acrylic distemper (ready mixed) having VOC

content less than 50 gram/litre, of approved manufacturer and of required shade

13.41 and colour all complete to achieve even shade and colour :

New work (two or more coats) over and including water thinnable priming coat

48 13.41.1 with cement primer having VOC content less than 50 gram/litre sqm 1242.00 220.38 273711.96

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone

additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10

49 13.47.1 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm 776.00 203.11 157613.36

Providing and applying white cement based putty of average thickness 1 mm, of

approved brand and manufacturer, over the plastered wall surface to prepare the

50 13.80 surface even and smooth complete sqm 1242.00 185.24 230068.08

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two

or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @

51 13.48.3 0.80 ltr/10 sqm of approved brand and manufacture sqm 35 202.63 7092.05

SH-12 FALSE CEILING WORK

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm

in true horizontal level, suspended on inter locking metal grid of hot dipped

galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive)

consisting of main “T” runner with suitably spaced joints to get required length

and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200

mm center to center and cross “T” of size 24x25 mm made of 0.30 mm thick

(minimum) sheet, 1200 mm long spaced between main “T” at 600 mm center to

center to form a grid of 1200x600 mm and secondary cross “T” of length 600 mm

and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at

middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of

size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid

including, required cutting/making, opening for services like diffusers, grills, light

fittings, fixtures, smoke detectors etc. Main “T” runners to be suspended from

ceiling using GI slotted cleats of size 27 x 37x 25 x1.6 mm fixed to ceiling with

12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with

52 12.52.1 galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center sqm 150.00 2258.92 338838

to center along main T, bottom exposed width of 24 mm of all T-sections shall be

pre-painted with polyester paint, all complete for all heights as per specifications,

drawings and as directed by Engineer-in-charge.GI Metal Ceiling Lay in plain

Tegular edge Global white colour tiles of size 595x595 mm,and 0.5 mm thick with

8 mm drop; made of G I sheet having galvanizing of 100 gms/sqm (both sides

inclusive) and electro statically polyester powder coated of thickness 60 microns

(minimum), including factory painted after bending.

NDSR WATER PROOFING WORK

Providing and applying water proofing treatment by the in house application wing

of the manufactuer or skilled project applicator to the water retaining structures -

Internal surface (potable water tanks) in 2 coats of two-component, solvent-free,

thixotropic, non-sag polyurethane coating, Priming the surface with PU primer at

200 grams/Sqm, followed by the application of waterproof coating should be

applied in two coats by roller only @ 1.5 kg/sq.m. (0.75 kg/sq.m. in 1st coat and

remaining in 2nd coat). Gap between the two coats application shall not exceed 12

hours. The coating shall have solids content of 100%, Elongation of 100% &

Tensile Strength >12Mpa as per ASTM D412, Hardness >40 as per ASTM D

2240, Hydrostatic Pressure resistance of 5bar as per EN12390, Adhesion to

concrete >1.5Mpa as per ASTM D7234 and Water Absorption <0.5 % as per

ASTM D570, Certified by CFTRI as per 21 CFR 175 – 300 of US – FDA for

potable water contact all as per manufacturers' specification, etc, complete.

53 The system includes base preparation of cleaning, brushing and removal of flacky sqm 70.00 1450 101,500.00

materials, grouting the porous area with cementitious grout, sealing the minor

cracks, fix the Corner Joint tape at the corners when the first coat is still in wet

condition ad apply one additional coat at corner.

Note: This is a stand alone system and screed/plaster protection is not

required.High strength PU Waterproofing For Potable Water Tanks - Inside

(OHT/Raw Water Tank Etc.) Above 50KL

Digitally signed by DEEPAK

Providing and applying two component high performance polymer modifed

cementitious waterproofing coating, having minimum elongation of 200%, Tensile

strength 1.5 N/mm2 (As per ASTM D412), Adhesion Strength 1.2 Mpa (As per

ASTM D 7234), Crack bridging up to 2mm (As per ASTM C836) and food grade

certification by CFTRI, including reinforcing the coating with 45gsm glass fibre

mesh at all corners. The coating shall be applied with a total consumption of

2.2Kg/Sqm in two coats to achieve 1.2mm thickness. The coating shall be

continued to the entire horizontal area and should be terminated at 300mm above

FFL over the vertical surface as per manufacturers specification and methodology.

The system includes base preparation of cleaning, brushing and removal of flacky

54 materials, grouting the porous area with cementitious grout, sealing the minor sqm 130.00 585 76,050.00

cracks, proper coving of 50mm x 50mm between slab and wall junctions and pre-

wetting the surface to attain SSD condition before application of the waterproofing

coating, followed by the application of waterproof coating.TOILETS/ BALCONY/

UTILITY WATERPROOFING - Sunken slab

Providing and Applying two component elastomeric Polyurethane based cold

applied seamless waterproofing coating, to the RCC surface like Roof & Podium

area applied @ 2.1kgs/sqm in single coat using 3mm notched trowel to achieve

1.5mm DFT, including a prime coat of two component solvent free, medium

viscous, epoxy primer @0.2litre/sqm. The Waterproofing material shall have

Solids >98%, Tensile strength >6MPa, Elongation at break >600% as per ASTM D

412, crack bridging ability (no cracks up to 3.2mm) confirms to ASTM C 1305,

Puncture resistance >300N as per ASTM E154, Shore A Hardness >70 as per ASTM

D 2240, Adhesion to peel after water immersion as per ASTM C 794 at 5.2N.

Resistance to root penetration. Waterproofing coating shall be applied on the

entire horizontal surface extending upto 300mm above FFL over the vertical

55 surface. The finished cost to include surface preparation, making coving of 50 sqm 430.00 1450 623,500.00

mm X 50mm at all right angles of wall Junction with Polymer Repair Mortar and

lay 40gsm Geo-textile over the angle fillet when the first coat in still wet,

treatment of cracks completely as per specification.Newly Constructed

Roof/Podium with 2K Polyurethane Waterproof coating

Clean the surface, removing the laitance with wire brushing and water pressure jet

wash. Fill the cracks using a fibre reinforced crack filler, Crack-X range as per

TDS. Apply one coat of Efflorescence resistant penetrating primer, dilute with

water in the ratio 2:1 spreading at the rate of 0.125litre/sqm in the SSD condition

and allow it to cure for 4-6 hours (primer required only for fresh plaster surface).

Apply one coats of UV Resistant acrylic Waterproof Coating without any dilution

Maintain the spreading rate of 4.20 - 4.70 Sq.mt / litre / coat application to achieve

about 100-120 microns DFT. Apply second coat of UV Resistant acrylate Top

Coat with interval of 6 - 8 hours without any dilution spreading at rate of 6.0 - 6.5

Sq.mt / per litre / coat to achieve DFT of 60 – 70 microns. The material having

56 following technical properties: Attains hairline crack bridging up to 2 mm, sqm 776.00 345 267,720.00

Elongation of >100 % as per ASTMD 412; Tensile strength 2.50 Mpa per ASTM

D 412, Passes Water Resistance as per SS500 standard, Complies to anti

carbonation test as per EN 1062 part 6. External wall waterproof coating

Providing angle Fillet for Sunshade:

Apply one coat of SBR Latex bond coat by mixing URP with cement at a 1:1

ratio. Providing Minimum 75mm x 75mm thick angle fillet with CM of 1:3

57 admixed with SBR Latex at a dosage of 12-15% of Cement.Waterproofing sqm 53.00 125 6,625.00

Treatment for Sunshade on top of Plaster

SH-19 DRAINAGE WORK

Supplying and fixing C.I. cover without frame for manholes : 500 mm diameter

C.I. cover (medium duty) the weight of the cover to be not less than 58 kg

Providing M.S. foot rests including fixing in manholes with 20x20x10 cm cement

concrete blocks 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm

59 19.15.1 nominal size) as per standard design : With 20x20 mm square bar No 10.00 646.59 6465.9

SH-23 BORE WELL

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable

method prescribed in IS: 2800 (part I), including collecting samples from different

strata, preparing and submitting strata chart/ bore log, including hire & running

charges of all equipments, tools, plants & machineries required for the job, all

complete as per direction of Engineer-in-charge, upto 90 metre depth below

All type of soil - 350mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well,

unplasticized PVC medium well casing (RMS) pipe of required dia, conforming to

IS: 12818, including required hire and labour charges, fittings & accessories etc.

61 23.4 all complete, for all depths, as per direction of Engineer -in-charge.

150mm nominal size dia

Digitally signed by DEEPAK

`Gravel packing in tubewell construction in accordance with IS: 4097, including

62 23.8 providing gravel fine/ medium/ coarse, in required grading & sizes as per actual cum 10.00 2403.2 24032

requirement, all complete as per direction of Engineer-in-charge.

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to

establish maximum rate of usable water yield without sand content (beyond

permissible limit), with required capacity air compressor, running the compressor

for required time till well is fully developed, measuring yield of well by "V" notch

method or any other approved method, measuring static level & draw down etc. by

step draw down method, collecting water samples & getting tested in approved

laboratory, i/c disinfection of tubewell, all complete, including hire & labour

charges of air compressor, tools & accessories etc., all as per requirement and

direction of Engineer-in-charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to

the top of bore well housing/casing pipe, removable as per requirement, all

64 23.13 complete for bore of:

Providing and fixing M.S. clamp of requried dia to the top of casing/housing pipe

of tubewell as per IS:2800 (Part I), including necessary bolts & nuts requred size

65 23.14 complete.

Providing and fixing Bail plug/Bottom plug of required dia to the bottom of pipe

assembly of tubwell as per IS:2800 including necessary bolts & nuts of required

66 23.15 size complete.

BORE WELL INSTALLATIONS (NON-SCHEDULED ITEMS)

Supplying & Installation of suitable Hp submersible pump with cable 1x3x2.5

squmm(upto 75mtr) with flexible conduit 25mm dia, electrical out door pannel

with required electrical fitting such as MCB of 0-25Amp , Volt & Ampere meter ,

single phase preventer starter etc of approved make, 40mm HDPE Pipe (25 mtr) each 1.00 44339.4 44,339.40

and all accessories complete as per requirement of site.

a) Contractor shall include the rate of electrical control panels complete with all

accessories &controls, all Electrical/Mechanical items as required to operate the

67 NDSR system automatic/manual.

b) Contractor to select suitable HP of pumps .

c) Level Controller with sufficient nos. of low / high level alarms, contacts with

electrodes and control wiring for the automatic operation of water supply pumps,

Submersible Sump Pumps, to achieve the functional requirement shall be

provided. Control wiring between these pumps and water tanks shall be

provided.Domestic water pumps must start at low water level in overhead

domestic water tank & stop at high level in that water tank. Dry running protection

shall be provided for all the pumps.Sequencing shall be provided for each set of

pumps. complete as per direction of EIC.

Digitally signed by DEEPAK

BOQ Plumbing Work

Rate (INR) Amount (INR)

DSR Item RATE inc

S.No. DESCRIPTION OF ITEM UNIT QUANTITY NDSR

No./NDSR correction NDSR DSR-2023

SH-17 INTERNAL PLUMBING WORKS

Providing and fixing rimless wall mounted water closet P trap with soft close seat cover Each

1 NDSR and concealed flushing cistern with dual flush fittings (6/3L flush) including nuts, bolts 9 25735.00 231615.00

etc complete in all respect as per directions of Engineer-in-Charge.

Providing and fixing Stainless steel with powder coating Half frame including rag bolts

2 NDSR and accessories for fixing concealed flushing cistern and water closet in position including 9 3717.00 33453.00

cutting walls and making good the same as directed by the engineer in charge.

Supplying and fixing white glazed European water closet, wash basin 510x400 mm,

600x100 hinged hand rail-1 nos, 600mm long grab bars-4 nos and all associated

3 NDSR accessories like flushing cistern, raised seat and cover, CP brass elbow operated pillar tap , 2 65782.00 131564.00

waste coupling etc. to make the toilet functional for special need persons including cutting

and making good the walls and floor, etc. complete.

Supplying and fixing 560x400x205mm or nearest size Oval shape wash hand basin of

white glazed earthenware (Indian make best quality) counter sunk already built with

4 NDSR necessary chipping and chamfering and finishing including supplying and fixing C P brass 5 19714.00 98570.00

waste, deck mounted sensor pillar tap. including cutting and making good the walls,

providing brackets for supports etc. complete.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm

C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting

5 NDSR and making good the walls wherever require: 5 15889.00 79445.00

White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P.

brass pillar tap

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste

fittings complete.

17.28.2 Flexible Pipe

Providing and fixing bevelled edge 6mm mirror of superior glass (of approved quality) Each

7 17.31 complete with 6mm thick hard board ground fixed to wooden cleats with C.P. brass 8 1908.73 15269.87

screws and washers complete.

Providing and fixing Stainless Steel AISI 304(18/8) kitchen sink as per IS : 13983 with

8 17.10 C.I. brackets and stainless steel plug 40mm including painting of fittings and brackets,

cutting and making good the walls wherrerever required.

17.10.2.2 Kitchen sink without drain board Size 610x460 mm bowl depth 200 mm Each 3 4598.43 13795.30

Providing and fixing white vitreous china battery based infrared sensor operated urinal of

approx.size 610x390x370 mm having pre & post flushing with water ( 250 ml & 500 ml

consumption), having water inlet from back side, including fixing to wall with suitable

brackets all as per manufacturers specification and direction of Engineer - in-charge.

Providing and fixing stone slab table rubbed, edges rounded and polished of size 75x50cm

deep and 1.8cm thick fixed in Urinal partitions by cutting a chase of appropriate width

10 8.10 with chase cutter and embedding the stone in the chase with epoxy grout or with cement

concrete 1:2:4 (1cement: 2coarse sand: 4graded stone aggregate 6mm nominal size) as per

direction of Engineer-in-charge and finished smooth.

8.10.2 Granite Stone of approved shade Each 8 4809.79 38478.31

CP Brass fittings

11 18.21 Providing and fixing unplasticised PVC connection pipe with brass unions.

18.21.2 45 cm length

18.21.2.1 15 mm nominal bore Each 10 116.04 1160.35

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with Each

12 NDSR S.S. triangular plate to Eureopean & Wall moutain type W.C. of quality and make as 11 1963.00 21593.00

approved by Engineer - in - charge.(Health Faucet).

Digitally signed by DEEPAK

13 18.49 Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :

18.49.1 a) 15 mm nominal bore Each 11 601.60 6617.62

Providing and fixing C.P. brass angle valve for basin mixer and gyser points of approved

quality conforming to IS:8931 .

18.53.1 a) 15 mm nominal bore Each 21 681.73 14316.30

Supply and fixing CP brass sink cock (Wall mounted) with long swivel spout and wall Each

flange in position.

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved

make conforming to IS:8931:

18.52.1 15mm nominal bore Each 6 795.86 4775.19

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as Each

per the direction of Engineer-in-charge. .

Providing and fixing SS liquid soap container 109 mm wide, 125 mm high and 112 mm Each

18 NDSR distance from wall of standard shape with bracket of the same materials with snap fittings 8 2118.00 16944.00

of approved quality and colour, weighing not less than 105 gms..

Providing and fixing SS towel rail complete with brackets fixed to wooden cleats with CP

brass screws with concealed fittings arrangement of approved quality and colour.

600 mm long towel rail with total length of 600 mm, 78 mm wide and effective height of Each

88 mm, weighing not less than 170 gms..

20 NDSR Providing and fixing SS towel ring Each 3 1201.00 3603.00

21 NDSR Providing and Fixing double coat hook. Each 11 937.00 10307.00

UPVC WASTE & VENT PIPES AND FITTINGS

Supply and fixing SWR Type B sanitary concealed pipes and specials , jointing with

solvent cement and fixing them on slabs, floors etc. in position for connecting various

fixtures (including fixing of pipes in sleeves/ drilled holes before water proofing) and

specials with brick or CC supports wherever necessary including cutting and chasing

brick walls as required, making good the same with brick in CM 1:6 and plastering with

CM 1:4, 12mm thick one coat, sealing joints between pipe and concrete, complete

Supply , jointing and fixing SWR type B Sanitary exposed pipes, specials and pipe

supports with good quality solvent cement and teflon tape and fixing the same to line,

23 NDSR plumb and level on the sides of ducts, walls, suspended to slabs as the case may be by

using slotted rails , U clamps, 8mm threaded rods and other required materials including

drilling holes, making good the walls, cleaning etc. and finishing complete

24 NDSR Supplying and fixing PVC multi Floor Trap 100mmx75mm size without Jali in position 15 242.00 3630.00

Providing and fixing SS grating of approved quality. Rectangular type with openable Each

25 NDSR circular lid : 150 mm nominal size square 100 mm diameter of the inner hinged round 15 203.00 3045.00

Providing and fixing stainless steel floor clean-out/maintenance access cover of approved

make, grade SS 304, with stainless steel frame and removable cover, suitable for

26 NDSR connection to the UPVC SWR drainage system, of size and configuration as required, 8 426.00 3408.00

including necessary adaptor/socket, gasket/seal, screws/fasteners, fixing and sealing,

making good the floor finish.

Providing and fixing multi-floor trap of approved make, suitable for connection to the

urinal waste outlets complete with water seal and a stainless steel maintenance/clean-out

access cover with frame, fixed over the multi-floor trap and accessible from finished floor

level for cleaning and maintenance. The cover shall be of SS 304 grade, with suitable

frame, removable cover and fixing arrangement, including necessary connectors, adaptors,

gaskets, seals and other accessories, properly jointed and fixed in position, including

cutting, drilling, chasing, making good, sealing and testing, complete as directed by the

Engineer-in-Charge.

28 NDSR Providing and fixing PVC vent cowl

INTERNAL RAIN WATER DRAINAGE WORK

Providing and fixing on wall face unplasticised-Rigid PVC rain water pipes conforming to

29 12.41 IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm

gap for thermal expansion.

Providing and fixing on wall face unplasticised PVC moulded fittings/accessories for

unplasticised Rigid PVC rain water pipes conforming to IS:13592 Type A including

jointing with seal ring conforming to IS:5382 leaving 10mm gap for thermal expansion.

12.42.1 Coupler

31 12.42.5.2 Bend 87.5 degree

Digitally signed by DEEPAK

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter EACH

and weighing not less than 440 grams.

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete

1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over

33 12.22 PVC sheet 1m x 1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 6 354.04 2124.24

coarse sand) and a coat of neat cement,punning,rounding the edges and making and

finishing the outlet complete.

INTERNAL WATER SUPPLY WORKS

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal

stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c

34 fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings

with one step CPVC solvent cement and the cost of cutting chases and making good the

same including testiang of joints complete as per direction of Engineer in Charge.

Concealed work including cutting chases and making good the walls etc.

18.8.2 20mm dia nominal outer dia pipes Mtr 75 638.16 47862.26

18.8.3 25mm dia nominal outer dia pipes Mtr 80 744.58 59566.67

18.8.4 32mm dia nominal outer dia pipes Mtr 25 877.59 21939.84

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal

stability for hot & cold water supply, including all CPVC plain & brass threaded fittings,

including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes &

fittings with one step CPVC solvent cement and testing of joints complete as per direction

of Engineer in Charge.

Internal work - Exposed on wall

18.7.3 25mm dia nominal bore Mtr 40 476.66 19066.56

18.7.4 32mm dia nominal bore Mtr 35 615.79 21552.56

18.7.5 40mm dia nominal bore Mtr 45 834.44 37549.97

18.7.6 50mm dia nominal bore Mtr 15 1108.89 16633.38

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal

stability for hot & cold water supply including all CPVC plain & brass threaded fittings

This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching,

refilling & testing of joints complete as per direction of Engineer in Charge.External work

18.9.3 25mm dia nominal bore Mtr 35 421.88 14765.80

37 18.17 Providing and fixing gun metal gate valve with wheel of approved quality.

18.17.1 25mm dia nominal bore each 2 738.83 1477.65

18.17.2 32mm dia nominal bore each 3 818.60 2455.79

18.17.3 40mm dia nominal bore each 2 980.63 1961.26

18.17.4 50mm dia nominal bore each 2 1218.70 2437.39

38 NDSR Providing and fixing CI Y type strainer of approved quality (Flanged end) :

a) 40mm dia nominal bore each 2 5597.00 11194.00

b) 50mm dia nominal bore each 2 8294.00 16588.00

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS :

39 18.48 12701 marked, with cover and suitable locking arrangement and making necessary holes

for inlet, outlet and overflow pipes but without fittings and the base support for tank.

a) 10000L Tank for fire Ltr 10000 13.06 130600.00

b) 2500L tank for domestic & flushing Ltr 2500 13.06 32650.00

SH-18 EXTERNAL PLUMBING WORKS

Supply and Laying SWR Type B pipes, lowering into trenches, placing in position,

aligning to line and levels and jointing with solvent cement including earth work

excavation in all classes of soil, refilling the trenches and transporting excess soil as

recommended by the site engineer, complete. (For sewer lines).

c) 75 mm. dia. metre 10 875.00

Constructing brick masonry manhole in cement mortar 1:4 (1 cement :4 coarse sand) RCC

top slab with 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal

size), foundation concrete 1:4:8 mix (1 cement :4 coarse sand :8 graded stone aggregate

41 19.7 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement :3

coarse sand) finished with floating coat fo neat cement and making channels in cement

concrete 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nminal size)

finished with a floating coat of neat cement complete as per standard design.

Inside size 90x80cms and 45cms deep including CI cover with frame (light duty)

19.7.1 455x610mm internal diamensions total weight of cover and frame to be not less than 38

kg (weight of cover 23 kg and weight of frame 15kg).

With common burnt clay FPS (non modular) bricks of class designation 75

42 19.8.1.1 Extra for depth for manholes:

Size 90x80cm with With common burnt clay FPS (non modular) bricks of class metre

designation 7.5

Inside size 90x120cms and 90cms deep including CI cover with frame (MEDIUM duty)

43 19.7.2 455x610mm internal diamensions total weight of cover and frame to be not less than 116

kg (weight of cover 58 kg and weight of frame 58kg).

With common burnt clay FPS (non modular) bricks of class designation 75

44 19.8.2.1 Extra for depth for manholes:

Size 90x120cm with With common burnt clay FPS (non modular) bricks of class metre

designation 7.5

Providing and fixing Square- mouth SW gully trap class SP-1 Complete with CI Grating

brick masonry chamber with water tight CI Cover with frame of 300 X 300mm size

(inside) the weight of cover to be not less than 4.50kg and frame to be not less than 2.70kg

as per standard design.

Digitally signed by DEEPAK

100 x 100 mm size P type with common burnt clay F.P.S(non modular) brick of class each

designation 7.5

150 x 100 mm size P type with common burnt clay F.P.S(non modular) brick of class each

designation 7.5

SH-19 SITC PUMP

Supply, Erection, Testing and Commissioning of Open well submersible pump (Transfer

pump) set capable of lifting 70 lpm of water against a total head of 25m - 2 nos (1 working

and other standby) with accessories such as 40mm non return valve - 2nos, 40mm full

46 NDSR way wheel valve - 2nos, pump panel having MCB, digital diaplay of voltage and current, set 1.00 57750.00 57750.00

Indicating lamps, manual switches, digital function capable of dry run prevention and

automatic interchange system all enclosed within a single panel

(Approximately 1HP, Filling time 25min) complete in all respect.

Supply, erection, testing and commissioning of Pressure Booster pump capable of

delivering 100Lpm discharge at a head of 2.5Bar (1 working only), the system shall be

47 NDSR capable of automatic start and stop operation and complete with Hydro tank of 60L Nos 1.00 63454.00 63454.00

capacity, dry run preventor, pressure sensors, pressure gauge, pump panel, necessary

cabling and bypass arrangements, with skid etc. complete in all respect.

Total Carried over to summary 849967.91 1143603.00

Digitally signed by DEEPAK

ELECTRICAL WORKS

Rate (INR) Amount (INR)

Sl No Item Description Unit Qty

No/NDSR DSR-2025 NDSR DSR 2025 NDSR

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5

sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in

surface/ recessed medium class PVC conduit, with modular switch,

1 1.1 modular plate, suitable GI box and earthing the point with 1.5 sq.mm

FRLS/HFFR PVC insulated copper conductor single core cable etc. as

Wiring for twin control light point with 1.5 sq.mm FRLS/HFFR PVC

insulated copper conductor single core cable in surface / recessed medium

class PVC conduit, 2way modular switch, modular plate, suitable GI box

2 1.11 and earthing the point with 1.5 sq.mm FRLS/HFFR PVC insulated copper

conductor single core cable etc. as required.

Wiring for circuit/ sub main wiring along with earth wire with the following

sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in

3 1.14 surface/ recessed medium class PVC conduit as required.

c 1.14.3 2 X 4 sq. mm + 1 X 4 sq. mm earth wire m 100 373 37300

Supplying and fixing of following sizes of medium class PVC conduit along

with accessories in surface/recess including cutting the wall and making

4 1.21 good the same in case of recessed conduit as required..

Supplying and fixing metal box of following sizes nominal size) on surface

or in recess with suitable size of phenolic laminated sheet cover in front

5 1.22 including painting etc. as required.

Supplying and fixing following modular switch/ socket on the existing

modular plate & switch box including connections but excluding modular

6 1.24 plate etc. as required.

b 1.24.5 6 pin 15/16 A socket outlet Each 20 721 14420

Supplying and fixing modular blanking plate on the

existing modular plate & switch box excluding modular plate as required.

Supplying and fixing following size/ modules, GI box along with modular

base & cover plate for modular switches in recess etc. as required.

a 1.27.1 1 or 2 Module (75mmX75mm) Each 40 354 14160

Supplying and fixing following Modular base & cover plate on existing

modular metal boxes etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in

front on surface or in recess, including providing and fixing 3 pin 5/6 A

10 1.31 modular socket outlet and 5/6 A modular switch, connections etc. as

required. Each 90 545 49050

Supplying and fixing suitable size GI box with modular plate and cover in

front on surface or in recess, including providing and fixing 6 pin 5/6 &

11 1.32 15/16 A modular socket outlet and 15/16 A modular switch, connections

etc. as required. Each 40 659 26360

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/

wooden block including connections etc. as required. Each 25 104 2600

Supplying and fixing stiff pendent with 300 mm long, 20 mm dia X 1.6 mm

thick steel conduit, aluminium cast back plate and brass holder complete,

13 1.36 including wiring the down rod with 1.5 sq. mm FRLS/HFFR PVC insulated,

copper conductor, single core cable and painting etc. as required.

Digitally signed by DEEPAK

Supplying and fixing call bell/ buzzer suitable for single phase, 230 V,

complete as required. Each 1 112 112

Supplying and fixing extra conduit down rod of 20 cm length G.I. pipe 15

mm dia, heavy gauge including painting etc. as required. (Note : More than

15 1.48 5 cm length shall be rounded to the nearest 10 cm and 5 cm or less shall

be ignored) Each 80 59 4720

Installation, Testing and Commissioning of exhaust fan in the existing

16 1.50 opening, including making good the damage, connection, testing,

commissioning etc. as required.

a 1.50.1 Upto 450 mm sweep Each 1 556 556

Wiring for group controlled (looped) light point/fan point/exhaust fan point/

call bell point (without independent switch etc.) with 1.5 sq. mm

FRLS/HFFR PVC insulated copper conductor single core cable in surface/

17 1.55 recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS/HFFR

PVC insulated copper conductor single core cable etc. as required.

Supplying and fixing PVC batten/ angle holder including connections etc.

as required. Each 15 132 1980

Providing and fixing following rating and breaking capacity and pole MCCB

with thermomagnetic release and terminal spreaders in existing cubicle

19 2.2 panel board including drilling holes in cubicle panel, making connections,

Ics=100% Icu and Operational Voltage 690V etc. as required.

Supplying and fixing following way, single pole and neutral, sheet steel,

MCB distribution board, 240 V, on surface/ recess, complete with tinned

20 2.3 copper bus bar, neutral bus bar, earth bar, din bar, interconnections,

powder painted including earthing etc. as required. (But without

MCB/RCCB/Isolator)

a 2.3.2 8 way , Double door Each 2 2773 5546

Supplying and fixing following way, horizontal type three pole and neutral,

sheet steel, MCB distribution board, 415 V, on surface/ recess, complete

21 2.4 with tinned copper bus bar, neutral bus bar, earth bar, din bar,

interconnections, powder painted including earthing etc. as required. (But

without MCB/RCCB/Isolator).

a 2.4.2 6 way , Double door Each 4 5299 21196

Supplying and fixing of following ways surface/ recess mounting, vertical

type, 415 V, TPN MCB distribution board of sheet steel, dust protected,

duly powder painted, inclusive of 200 A tinned copper bus bar, common

22 2.5 neutral link, earth bar, din bar for mounting MCBs (but without MCBs and

incomer ) as required. (Note : Vertical type MCB TPDB is normally used

where 3 phase outlets are required.)

a 2.5.1 4 way , Double door Each 2 7951 15902

b 2.5.2 8 way , Double door Each 1 10724 10724

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve,

miniature circuit breaker suitable for inductive load of following poles in the

23 2.10 existing MCB DB complete with connections, testing and commissioning

etc. as required.

3 2.10.1 Single pole Each 40 285 11400

b 2.10.3 Double pole Each 2 696 1392

c 2.10.4 Triple pole Each 15 1070 16050

d 2.10.5 Triple pole and Neutral Each 8 1301 10408

Supplying and fixing single pole blanking plate in the existing MCB DB

complete etc. as required. Each 30 14 420

Supplying and fixing following rating, double pole, (single phase and

neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity

25 2.14 current 30 mA in the existing MCB DB complete with connections, testing

and commissioning etc. as required.

Supplying and fixing following rating, four pole, (three phase and neutral),

415 volts, residual current circuit breaker (RCCB), having a sensitivity

26 2.15 current 30 mA in the existing MCB DB complete with connections, testing

and commissioning etc. as required.

Supplying and fixing DP sheet steel enclosure on surface/ recess along

27 2.16 with 25/32 A 240 V "C" curve DP MCB complete with connections, testing

and commissioning etc. as required. Each 3 1258 3774

Supplying and fixing TP sheet steel enclosure on surface/ recess along

28 2.17 with 16/25/32 A 415 V "C" curve TP MCB complete with connections,

testing and commissioning etc. as required. Each 3 1707 5121

Supplying and installing following size of perforated Hot Dipped Galvanised

Iron cable tray (Galvanisation thickness not less than 50 microns) with

perforation not more than 17.5%, in convenient sections, joined with

29 4.6 onnectors, suspended from the ceiling with two numbers GI Suspenders i/c

base of suitable size GI angle, GI bolts & nuts, fastner etc as required.

a 4.6.4 300 mm width X 50 mm depth X 1.6 mm thickness m 150 1062 159300

Digitally signed by DEEPAK

Supplying and installing following size of perforated Hot Dipped Galvanised

Iron cable tray "bends" (galvanisation not less than 50 microns) with

perforation not more than 17.5%, in convenient sections, joined with

30 4.7 connectors, suspended from the ceiling with two numbers GI Suspenders

i/c base of suitable size GI angle, GI bolts & nuts, fastner etc as required.

a 4.7.4 300 mm width X 50 mm depth X 1.6 mm thickness Each 20 1977 39540

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including

accessories, and providing masonry enclosure with cover plate having

31 5.4 locking arrangement and watering pipe of 2.7 Meter long etc. with charcoal/

coke and salt as required. Set 4 8351 33404

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground

as strip earth electrode, including connection/ terminating with G.I. nut,

32 5.9 bolt, spring, washer etc. as required. (Jointing shall be done by overlapping

and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from

33 5.11 earth electrode including connection with G.I. nut, bolt, spring, washer

excavation and re-filling etc. as required. m 100 755 75500

Providing and laying earth connection from earth electrode with 6 SWG dia

G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection

34 5.12 with G.I. thimble excavation and re-filling as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for

connections etc. as required. m 200 287 57400

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop

earthing as required. m 150 84 12600

Supplying, installation, Testing & Commissioning of LED Recessed/surface

LED Down lighter SMD Type (Round/ square/ Rectangular) SMD type of

following body material with PMMA and prismatic diffuser and construction

as per IS : 10322 with driver as per the requirement with Driver efficiency

>85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating

temp range -5 0C to 40 0C centigrade, internal surge protection of 2.5 KV

with Short & Open circuit protection ,THD < 10%, P. F.≥0.95, IP20, CRI

37 8.2 >80, UGR (Unified Glare Rating) <19, Flicker free (flicker should be below

5 %), life time (LED, Driver & electrical circuitry), life time of minimum

50000 Burning Hours with 70% of initial Lumen maintained till life ends,

CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin),

SDCM(Standard Deviation Color Matching) <3,

Maximum power consumption should not more than the specified rating

and Fixture shall be of relevant BIS standard. Manufactures Word Mark/

Name Engraved/ Embossing/ Screen printing on housing Complete in all

respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC

insulated copper conductor single core cable and earthing etc. as required

with Minimum 5 year OEM warranty. System lumen efficacy ≥120 <135

lm/Watt output . LM79 & LM80 Test report and all testing required for LED

fixtures as per BIS shall be submitted.. Shape size

and CCT shall be as approved by Engineer-in- Charge as per requirement.

(Thermal management: heat sink of aluminium housing such that LED

junction temperature shall not rise above 90°C). Powder coated die cast

/Extruded aluminium Body including trim .

Supplying, Installation, Testing & Commissioning of Panel light 2x2 ft., of

following body material and construction as per IS : 10322 with driver as

per the requirement with Driver efficiency >85%, Operating voltage AC

140-270 Volt, frequency 50/60 hz, Operating temp range -5 0C to 40 0C,

internal surge protection of 2.5 KV with Short & Open circuit

protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80, UGR (Unified Glare

38 8.7 Rating) <19, Flicker free, (flicker should be below 5 %), life time (LED,

Driver & electrical circuitry), of minimum 50000 Burning Hours with , 70%

of initial Lumen maintained till life ends, CCT 3000°K / 4000°K / 5700°K

/6500°K (As per ANSI Bin), SDCM (Standard Deviation Color Matching)

Maximum power consumption should not more than the specified rating

and Fixture shall be of relevant BIS standard. Manufactures Word Mark/

Name Engraved/ Embossing/ Screen printing on housing. complete in all

respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC

insulated copper conductor single core cable and earthing etc. as required

with Minimum 5 year OEM warranty. System lumen efficacy ≥120 <135

lm/Watt output .LM79 & LM80 Test report and all testing required for LED

fixtures as per BIS shall be submitted. Shape size and CCT shall be as

approved by Engineer-in-Charge as per requirement. (Thermal

management: heat sink of aluminium housing such that LED junction

temperature shall not rise above 90°C). Powder coated die cast / Extruded

aluminium Body (Thickness > 1.20 mm)

Supplying, installation, Testing & Commissioning of LED surface mounted

Batten light of following body material and construction as per IS : 10322

with driver (Replaceable) as per the requirement with Driver efficiency

>85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating

temp range -5 0C to 40 0C, internal surge protection of 2.5 KV with Short &

39 8.10 Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80, Flicker

free (flicker should be below 5 %), life time (LED,Driver & electrical

circuitry), of minimum 50000 Burning Hours with 70% of initial Lumen

maintained till life ends, CCT 3000°K / 4000°K / 5700°K /6500°K

Digitally signed by DEEPAK

(As per ANSI Bin), SDCM(Standard Deviation Colour Matching) <3,

Maximum power consumption should not more than the specified rating

and Fixture shall be of relevant BIS standard. Manufactures Word Mark/

Name Engraved/ Embossing/ Screen printing on housing. complete in all

respect i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC

insulated copper conductor single core cable and earthing etc. as required

with Minimum 5 year OEM warranty. System lumen efficacy ≥120 <135

lm/Watt output . LM79 & LM80 Test report and all testing required for LED

fixtures as per BIS shall be submitted. Shape size and CCT shall be as

approved by Engineer-in-Charge as per requirement. (Thermal

management: heat sink of aluminium housing such that LED junction

temperature shall not rise above 90°C). Powder coated die cast /Extruded

aluminium Body (Thickness > 1.20 mm)

Supplying, Installation, Testing & Commissioning of LED Flood Light,

powder coated pressure die cast aluminium body with built in or separate

driver as per the requirement with Driver efficiency >85%, Input voltage:

Input voltage: 140-270 Volt AC, frequency 50/60 hz, Operating temp range

-5 0C to 50 0C, internal surge protection of 5 KV L,N,E as per IEC 61000-

40 8.16 4-5, Driver efficiency >85%,THD < 0% as per IEC 61000-3-2, P. F.≥0.95,

IP-66,IK-10, CRI >70, under voltage and over voltage protection, EMI-EMC

as per CISPR-15, lenses for beam angle 30 deg-120deg as per the

application and the project requirement, suitable tilt able fitting,

life time (LED, Driver & electrical circuitry) of minimum 50000 Burning

Hours with 70% of initial Lumen maintained till life ends as per LM80

extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K / 5700°K

/6500°K (As per ANSI Bin), SDCM(Standard Deviation Colour Matching)

<5, Maximum power consumption should not more than the specified rating

and Fixture shall be of relevant BIS standard complete in all respect i/c

external connections with 1.5 sq.mm FRLS/HFFR, PVC insulated copper

conductor single core cable and earthing etc. as required with Minimum 5

year OEM warranty. System lumen efficacy ≥120 and <135 lm/Watt

output . LM79 & LM80 Test report and all testing required for LED fixtures

as per BIS shall be submitted.. Shape size and CCT shall be as approved

by Engineer-in-Charge as per requirement. (Thermal management: heat

sink of aluminium housing such that LED junction temperature shall not

rise above 90°C).

Supply, Installation, Testing and Commissioning of ceiling fan with Remote,

Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos.

metal(Aluminium alloy) blades, 30 cm long down rod, 2 nos. canopies,

shackle kit, safety rope, copper winding, steel/Al body. Power Factor not

less than 0.9, Service Value (CM/M/W) minimum as below, 350 RPM

(tolerance as per IS : 374-2019), THD (Total Harmonic Distortion) less than

10%, remote (preferably mobile app based) for speed control and all

41 9.1 remaining accessories including safety pin, nut bolts, washers, temperature

rise=75 0C (max.), insulation resistance more than 2 mega ohm, suitable

for 230 V, 50 Hz, single phase AC supply Ceiling Fan compliant to IS

374:2019 fan i/c external connections with 1.5 sq.mm FRLS/HFFR, PVC

insulated copper conductor single core cable and earthing etc. as required.

1200mm, service value ≥ 6.0 CM/Min/Watt, air delivery 210 CM/Min

Laying of one number PVC insulated and PVC sheathed / XLPE power

42 10.5 cable of 1.1 KV grade of following size in the existing RCC/ HUME/ METAL

pipe as required.

b 10.5.2 Above 35 sq. mm and upto 95 sq. mm m 30 72 2160

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE

43 10.7 power cable of 1.1 KV grade of following size on wall surface as required.

a 10.7.1 Upto 35 sq. mm (clamped with 1mm thick saddle) m 20 64 1280

Above 35 sq. mm and upto 95 sq. mm (clamped with

b 10.7.2 25x3mm MS flat clamp) m 10 151 1510

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE

44 10.8 power cable of 1.1 KV grade of following size on cable tray as required.

a 10.8.1 Upto 35 sq. mm (clamped with 1mm thick saddle) m 200 53 10600

Above 35 sq. mm and upto 95 sq. mm (clamped with

25x3mm MS flat clamp) m 10 109 1090

Supplying and fixing cable route marker with 10 cm X 10 cm X 5 mm thick

G.I. plate with inscription there on, bolted / welded to 35 mm X 35 mm X 6

45 10.10 mm angle iron, 60 cm long and fixing the same in ground as required.

Supplying and making end termination with brass compression gland and

aluminium lugs for following size of PVC insulated and PVC sheathed /

46 11.1 XLPE aluminium conductor cable of 1.1 KV grade as required.

Supplying and laying of following size DWC HDPE pipe ISI marked along

with all accessories like socket, bend, couplers etc. conforming to IS

14930, Part II complete with fitting and cutting, jointing etc.direct in ground

47 15.16 (75 cm below ground level) including excavation and refilling the trench but

excluding sand cushioning and protective covering etc., complete as

Digitally signed by DEEPAK

a 15.16.2 90 mm dia (OD-90 mm & ID-76 mm nominal) m 100 336 33600

Outdoor 4MP_ Supplying Installation Testing and Commissioning of 4MP IP IR Outdoor

Bullet Camera having following specifications and features etc :- 1) Signal System:

PAL/NTSC, Signal to Noise Ratio: > 50 dB,Camera should display Camera title, Date &

Time in live & recorded video 2)Image Sensor: 1/2.8" or better progressive Scan CMOS

get color image even at night condition(Minimum Illumination: 0.006 Lux@ F1.4, AGC ON,

0 lux with IR or better) True Day & Night High Performance Mechanical IR cut filter with

auto switch, Integrated IR Source (Auto, Manual)- Inbuilt IR LED's with effective distance

upto 50 meter or better and 30 meter for colour view in night, Imaging: 1/3s to 1/30000s

electronic shutter support, Auto Gain Control , White Balance- Auto, Back Light

Compensation, Multi zone Privacy Masking, HLC, Digital Watermarking. 3) Compression

(Minimum): Video:- H.265 or better, Audio:- G.711U/A, G.711Mu, G.726, AAC, G.723 4)

Wide Dynamic Range:- WDR (120dB or more) 5) Digital Noise Reduction:- DNR (3D)

On/Off 6) Video Streaming & Frame Rates :- Triple streaming , configurable Main stream:

4MP (2560×1440)25/30fps Sub streams minimum: 720P@25/30 fps 7) Image Setting:

Rotate Mode, saturation, brightness, contrast, sharpness adjustable through client

software or web browser, Edge Analytics: Tripwire, Intrusion, Motion Detection 285 DELHI

SCHEDULE OF RATES (E&M)-2025 8) Cyber Security: AES 256-bit Encryption,

Configuration encryption, trusted execution, Digest, security logs, account lockout, video

40.4.1 encryption, IP/MAC filtering, HTTPS, trusted upgrade 9) Onboard Storage: Camera should 10 10063 100630

support built-in Micro SD/ SDHC/ SDXC Card slot upto 512 GB. It should be supplied with

minimum 128GB memory Card. 10) Recording Management: Format SD, overwrite,

storage management, video to NAS device, 11) Alarm Trigger : Motion/tampering

detection; network disconnection detection; IP conflict detection; memory card state

detection; memory space detection 12)Network Protocol: SFTP, IPv6, IPv4, DNS,RTCP,

NTP, RTP, HTTP, HTTPS, SNMP TCP/IP, PPPoE, NFS, UDP, ICMP, SSL, DHCP,

SMTP, RTSPS, unicast, 13) System Capability: ONVIF, Camera shall support open

source VMS 14) Ethernet: 1 RJ 45 10/100 Ethernet port 15) Audio : It should support 1 x

Built-In Mic and 1/1 Alarm In/ Out for External Mic. and Speakers as per site requirement.

16) Power Input: The camera should support simultaneous dual power input—12 VDC (via

power adapter) and PoE (802.3af)—to ensure continuous operation in the event of a

failure in one power source. 17) Power Requirement: 12VDC/24 VDC/PoE (802.3af)/ePoE

18) Housing/ Enclosure:- IP67 weather proof, IK10, Metallic body 19) Operating

Condition:- Ambient Temperature:- (- )05°C to 50°C, humidity 95% (max) (non-

condensing) 20) IR life: 40000 hours or higher 21) Video Bit rate: 32 KBPS - 8 MBPS or

better 22) Standards: BIS with ER, STQC Certified, CE, FCC and RoHS 40.4.1 4MP @

25/30fps@1440P (2560 x 1440) Outdoor Bullet Camera with 2.8/ 3.6/6/8/12 mm fixed lens

(as per site requirement) Nos

16 Channel Network Video Recorder (NVR) having display split :- Main screen:

Supplying, Installation, Testing and Commissioning following capacity Serveillance grade

40.12.1 Hard Disk with upto 256MB/s Transfer Rate, 256 MB Cache, 7200 RPM Disk Speed, 3.5 1 13943 13943

inch form factor, SATA Interface, BSMI, ICES-003/NNB-003, CE, FCC, KC, Maghreb, RCM,

UKCA, VCCI, CB-Scheme, TUV, UL Certifications. 40.12.1 4TB (Terabytes) Each 13943.00 NOs

Supplying, Installation, Testing and Commissioning of following size LED display (LED

monitor) industrial grade with 3840x2160 resolution or better, USB playback, bluetooth

42.4 and miracast connectivity, 4X HDMI 2.0, DP 1.2, HDR 10/10+, brightness: 500-nits or

better, Video wall mode should be available, contrast ratio: 1200:1, OPS slot, viewing

angle (H/V): 170°/ 170°, response time less than 12ms, Display control shall be on

monitor screen and programmable with remote (remote shall be supplied with system),

Key Board, Optical Mouse, etc. as required.

42.4.2 42 inch or larger NOs 1 51459 51459

Supplying, installation, Testing & Commissioning of following capacity

Three phase input and Three phase Output at full load (Unity Power

Factor) at operating temperature 0 to 40 0C, Relative humidity 0 to 95%,

Online double conversion true sine wave Uninterrupted hot swapable

(allow for the replacement or addition of battery modules without shutting

down the entire system) modular Power Supply (UPS) system with N+1

modules (N denotes total number of modules required for rated capacity).

The UPS shall include a Rectifier, inverter, battery bank suitable for 30

minutes back up (Battery VAH capacity shall not be less than 1600 VAH

48 26.2 per KVA of UPS rating per Hour backup time) on full load (Battery shall be

VRLA, SMF in ABS Container) and Static Bypass switch along with manual

bypass, suitable isolation transformer for additional protection against

neutral faults etc. UPS shall have inbuilt phase sequence correction. The

UPS systems offered are to be of the latest technology with Digital Control

Microprocessor based for reliable operation using Insulated Gate Bipolar

Transistor (IGBT)'s both for the rectifier & inverter (3 Level) with PWM

(Pulse Width Modulation).

The quality of design, manufacturing and inspection process should

confirm to the relevant Inter-national standards such as IEC/EN/VDE. The

operating efficiency of the UPS systems shall be >96% while operating on

battery mode and delivering quality power to the 100% non-linear loads.

Current total harmonic effect(ITHD) on the input grid shall be < 5% at 50

%load. (The required LC ( inductor (L) and a capacitor (C)) filters shall be

included in UPS cost), extreme power factor kit to be included to limit the

input power factor (PF) to 0.99 and output power factor shall be unity (i.e.

kw rating of the UPS shall be kva rating x 1 ), however UPS shall be

suitable to take load at 0.7 laging to 0.7 leading power factor loads. UPS

shall be suitable for incoming supply AC : 3Phase 400V +/-20%, 50 Hz +/-5

Hz, AC Output voltage: 3Phase 415 Volt, 50 Hz +/- 0.2Hz, Overload

capacity of 120% for 10 mins, Sine wave output.

Non condensing, noise level less than 60db at 1 meter distance,

protections: Input Under voltage over voltage, abnormal out voltage,

battery over charging, output over current, short circuit protection, battery

deep discharge protection, 10KV surge. UPS must comply with low voltage

electromagnetic compatibility (EMC) achieved as

per EN 6204, EN6204 Part I and Part 2, it shall be a Voltage and

Frequency Independent (VFI)-type UPS. Communication

RS232/RS485/SNMP port open protocol for BMS integration, all hardware

& software for iOT Communication as per approved by Engineering in

charge. Required battery racks and interconnecting copper conductor

cables of suitable size and connectors and all required accessories are

inclusive of the cost). This system must provide a means for logging and

alarming of all monitored points plus email notification. Forced air-cooling

with integral inbuilt fans with redundancy (if one fan fail UPS should be

able to handle at least 80% of the load, Noise Level 65 DB at 1 meter

distance. The system shall be in compliance IEC 62040- 1,2 & 3, IS: 16242

and CPWD Specification. Display Panel (minimum) (In-build 5 inch or more

LC Display / LED) to display : a) Input: Voltage, current, Frequency. b)

Bypass: Voltage, Frequency. c) Output: Voltage, frequency, Current. d)

Digitally signed by DEEPAK

e) Load: KVA, KW, Percentage. f) Temperature: STS, Inverter, PFC. g)

Event Logging & Statistical Data (On LCD/LED): UPS should capture and

display up to 3000 events like: Over temperature / DC Bus Fail / Fan Fail /

Fuse Fail / Overload / Short-circuit / Device Fail / Inverter Fail / Rectifier

Fail / Bypass Fail, etc. h) Statistical Data: No. of power failures / Transfers

to Bypass / Total Running time, etc. i) Mains Mode of Operation /Battery

Mode of Operation / Bypass feeding the load / UPS Fault /Battery charging

and discharging, overload, battery voltage and battery capacity. j) Audible

Alarms : Mains Failure, Battery Low Alarm, UPS Overload, Fault,

Shutdown, Input Over, Under Voltage, Output Over, Under Voltage, Battery

Over, Under Voltage, Over Load and short circuit, Over Temperature. The

UPS should have QR code which should contain drawing, test report OEM

manual, Geo- Tag of manufacturing location etc

a 15.16.2 10KVA (Each Power module shall be < 10 KVA) Each 1 208893 208893

Supplying, Installation, Testing & Commissioning of ‘Silent Type Diesel

Generating set as per CPCB IV + or better norms along with having Prime

Power Rating of KVA as below, 415 volts at 1500 RPM, 0.8 lagging power

factor at 415 V suitable for 50 Hz, 3 phase system & for 0.85 Load Factor,

including testing at factory and site with fuel, load for test and other

49 29.1 necessary arrangements Complete as per CPWD specifications, should

have QR code which should contain drawing, test report OEM

manual,Geo- Tag of manufacturing location, rating plate as per relevant IS

Code etc. and consisting of the followings:

(A) Diesel Engine:

Tourbocharged Diesel engine 4 stroke water cooled, multi cylinder,

dynamically balanced fly wheel, electric start of suitable BHP at 1500 RPM

suitable for above output of alternator at 40 0C, 50% RH & at 1000 Meter

MSL , capable of taking 10% over loading for one hour after 12 hours of

continuous operation. The engine will be with Electronic governor, Dry type

Air filter with service indicator, first filling of engine fuel (after

commissioning) lubricating Oil, Coolant and other consumables complete

with all the required accessories, the Electronic governor shall be as per

ISO 8528.The engine shall comply to the latest CPCB norms (CPCB IV +

or better) and Conforming to BS 5514, BS 649, IS 10000, IS 10002, IS

13018 and as per CPWD specifications.

(B) Engine mounted Instrument Panel fitted with and having digital dis

Plate for following:

(i) Start-stop switch with key

(ii) Water temperature indication

(iii) Lubrication oil pressure indication

(iv) Lubrication oil temperature indication

(v) Battery charging indication and Voltage indication

(vi) RPM indication

(vii) Over speed indication

(viii) Low lubricantion Oil trip indication

(ix) Engine Running Hours indication

(C) Alternator:

Synchronous alternator rated of appropriate KVA, 415 volts at 1500 RPM,

3 phase 50 Hz, AC supply with 0.8 lagging power factor at 40 0C, 50% RH

& at 1000 Meter MSL. The alternator shall be having Screen Protected Drip

Proof (SPDP) enclosure IP23, brushless, continuous duty, dynamically

balanced rotor, capable of taking 10% over loading for one hour after 12

hours of continuous operation, self cooled,self-excited and self-regulated

through AVR conforming to IS13364(Part 2)/IS: 4722/BS 2613 suitable for

tropical conditions and with class- H insulation.

(D) Base Frame & Foundation:

Both the engine and alternator shall be mounted on suitable base frame

made of MS channel with necessary reinforcement which shall be installed

on suitable cement concrete foundation and vibration isolation

arrangement as per recommendations of manufacturer.

Daily service fuel tank of suitable liters capacity as per PWD

Specifications, fabricated out of 3 mm thick M.S. sheet complete with all

standard accessories and fuel piping between fuel tank and diesel engine

with MS class ‘C’ pipes of suitable dia. Complete with valves, level

indications & accessories as required as per specifications.

(F) Exhaust System:

Dry exhaust manifold with hospital type exhaust silencer and catalytic

(G) Starting System:

12V/24V DC starting system comprising of starter motors: voltage regulator

and arrangement for initial excitation complete with suitable numbers of

batteries (180 AH capacity lead acid SMF type) as required as per

specifications. The battery shall be housed inside the acoustic enclosure of

(H) Acoustic and weather proof enclosure with arrangement for fresh air

intake for cooling of the engine & alternator, extraction, discharging hot air

in to the atmosphere and the temperature rise inside the enclosure, noise

level outside enclosure. The acoustic enclosure should be suitable for

cable connection/connection through bus-trunking. Such arrangements on

acoustic enclosure should be water proof & dust-proof conforming to IP-65

protection. The enclosure shall be as per CPCB IV + or better norms etc.

and as per CPWD specifications.

Digitally signed by DEEPAK

Free standing floor mounted IP 42 automatic mains failure control panel

including auto by-pass, suitable for KVA as below for silent type DG set

complete with relays, timers, set of CTs for metering & protection and

energy analyser to indicate currents, phase and line voltages, frequency,

power factor, KWH, Kilo Volt Ampere Reative Hour (KVARH), KVA (Phase

& Total), KW & provision for overload, short circuit, restricted earth fault,

under frequency, power (aluminium) and control (copper ) cabling of

suitable size upto 15 meter between AMF panel, LT Panel and DG Set

including connection interconnection etc. as required, all complete and

inter locking and communication/ Ethernet /RS485/SNMP port open

protocol for BMS integration including suitable software, the panel shall be

of DG Set OEM make etc. as per approved by Engineering in charge and

including the following:

1. Suitable numbers and appropriate capacity 4 pole motorised electrically

operated draw out with cradle type 3 position ACB/ MCCB with electronic

release for O/C & E/F and shunt trip or MCCB with electronic release for

O/C & E/F and shunt trip with 4 Pole Power Contactor.

2. Auto/Manual/Test/Off selector switch 3. Protection for under and over

voltage phase reversal (2 nos Over voltage relay, 2 Nos. reverse power

relay and 2 Nos. under voltage relay).

4. 3 Sets of current transformers 15 P 10 accuracy for protection and 15

VA class-I for metering

5. Energy analyser unit to indicate current, Voltage( LN & L_L), kW, kVA

(Phase & Total), Frequency, KWH, PF.

6. LED Indicating lamps for load on mains and load on set

7. Fuse/ MCB for instruments

8. Battery charger, complete with transformer/ rectifier, D.C. voltmeter and

ammeter, selector switch for trickle, off and boost and current adjustment.

9. Main supply failure monitor

10. Supply failure timer

11. Restoration timer

12. Control unit with three impulse automatic engine start/stop and failure

to start lockout.

13. Impulse counter with locking and reset facility.

14. ON/OFF/Control circuit switch with indicator

15. Audio/Video annunciation for

(i) High water temperature

(ii) Low lubricating oil pressure

(iii) Engine over speed

(iv) Engine fails to start

(v) Full load/maximum load warning

16. Protection for over/under Frequency, Loss of AC sensing, Over

Current, Unbalancing load with suitable number of relays and accessories

17. Maintenance notification based on Engine Run Hour & due date.

18. Load Management through PLC to achieve auto opening and closing of

incomer breakers, bus coupler switching of essential panel , interlocking

providing signal to AMF Panel for load status and AMF shall give command

to DG Set to auto start / auto stop depending upon load status and

requirement etc. and necessary hardware and software required to perform

the operation shall be provided by the contractor including all control

32.20 HI - WALL SPLIT SYSTEMS

Supplying , Installation, Testing and Commissioning of Air Cooled Hi Wall

split type Air conditioners complete with Indoor unit(IDU), Out door unit

(ODU), surface / concealed copper Refrigerant piping with insulation

(closed cell elastomeric nitrile rubber tubular pipe section) upto 3 Mtr IDU

to ODU), copper power cable upto 3.5 Mtr (IDU to ODU) i/c drain pipe R-

32/R-410/ R-407 Green Refrigerant, wireless remote control, suitable for

working between 180-260V with low & high voltage cutoff and 50 hz ,1

phase AC supply capable of performing cooling, dehumidification, air

circulation of following capacity with Scroll / rotary compressor. The system

shall be able to deliver 100% of the rated capacity upto 42 0C. Min 5 year

Original Equipment Manufacturer (OEM) warranty both compressor and

Printed Circuit Board (PCB). Must comply : Electrical cable IS 694 or IS

9968 temperature sensing control IS /International Electrotechnical

Commission (IEC) 60730, hermetic compressor IS 10617, heat exchanger

IS 11329, capacitor IS 2993 and motor IS 12615. Complete as per CPWD

specification and IS : 1391 Part II 2023. The system shall be able to

operate up to 50 0C (out door ambient temperature). Inverter Type -

32.2.3 1.5 TR with 5 Star BEE Rating Each 5 43539 217695

Digitally signed by DEEPAK

Supplying, Installation, Testing & Commissioning of following capacity passenger Machine room

less (MRL) lift with regenerative drive as per CPWD General Specification for Electrical Works

(Part-III Lift & Escalator) 2003, BIS Codes, NBC 2016 as amended upto date having provision for

barrier free access as per Harmonised Guidelines & Standards for Universal Accessibility in India -

2021 of MoHUA, serving different floors in the lift shaft as per detailed specifications enclosed and

as under including all other equipment and accessories complete as required:- (i) Speed-1 MPS (ii)

Floors-3 (G+2) (iii) Travel -10Meters (approx.) (iv) Stops & opening- 3 stops and 3 openings (v)

Controller: A.C. variable voltage & variable frequency (vi) Automatic rescue device (ARD) complete

with dry maintenance free batteries as required. vii) Operation: Microprocessor based single

automatic push button/simplex selective collective/duplex collective selective with/without

attendant (viii) Power-415 Volts+10%, 3 phase, 50 Hz, 4 wires system (ix) Car Enclosure: Stainless

steel scratch proof (Moon Rock/Honeycomb/ Hairline Finish) on all sides and stainless steel

decorative ceiling with fans (indirect throw) and LED fitting. (x) The car flooring should be smooth

and antiskid as approved by engineer-in-charge. (xi) Type of doors (a) Car: Power operated, centre

opening horizontal sliding stainless steel scratch proof (Moon Rock/Honeycomb/ Hairline Finish).

NDSR (b) Landing doors: stainless steel scratch proof . (xii) A hand rail not less that 600mm long at

900mm above floor level to be fixed adjacent to control panel in the lift car. (xiii)Voice

announcement system in the car to announce the position of the elevator in the hoist way as the

car passes or stops at floor served by the elevator. (xiv) Closed loop Control System, protection

against power fluctuation, self diagnostic control, Landing doors 2 hours Fire rated, Overload

detection and protection, Overspeed Governer, Dot Matrix LED D & P Indicators In Car & Landings,

BMS Compatibility, tamper proof infrared curtain covering almost the entire height of the lift car

door, Alarm horn, Anti Nuisance Operation, CCTV camera system with 4 MP IP camera, suitable

NVR and HDD for 30 days storage

backup , Firemen switch, 2/3 way intercom, Emergency Stop Switch with battery backup for fan

and light fitting for 1 hour, pit ladder. (xv) The lift doors shall have a vision panel to enable

persons with hearing impairment to signal for help or assistance in the event of an emergency.

(xvi) An appropriate technological support be provided (Through emergency messaging |services

or alarms etc.) to respond to the emergency requirements of person with hearing impairment or

deafness. (xvii) In case of failure of ARD or other electronic devices, a provision of manual rescue

Supplying and fixing of following ways surface/ recess mounting, vertical

type, 415 V, TPN MCCB distribution board of sheet steel, dust protected,

duly powder painted, IP43 as per IS 8623 III, impact resistance IK09,

50 NDSR inclusive of required tinned copper bus bar, common neutral link, earth bar,

din bar for mounting MCBs (but without MCBs and incomer ) as required.

(Note : Vertical type MCCB TPDB is normally used where 3 phase outlets

a 8 way , Double door Each 1 23396 23396

Supply of PVC insulated and PVC sheathed armoured underground

51 NDSR aluminium power cable of 1.1KV grade with ISI mark.

Supply, installation, testing and commisioning of AC Single phase Exhaust

52 NDSR fan 300mm sweep light duty, metal / plastic blade, MS / Fibre grill with all

required accessories. Each 3 1886 5658

Supply, installation, testing and commisioningof AC Single phase Wall

53 NDSR mounted fan 400mm sweep, metal / plastic aerodynamic blade with all

required accessories. Each 3 3237 9711

Supply, installation, testing and commisioningof the following rating, 415

V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of

54 NDSR following poles in the existing MCB DB complete with connections, testing

and commissioning etc. as required.

a 40A / 63A TP MCB Each 2 1500 3000

b 40A / 63A TPN MCB Each 2 1942 3884

Total Amount in Rs 2,807,962.00 1,517,899.00

Total Amount in Rs 2,807,962.00 1,517,899.00

Digitally signed by DEEPAK

Rate (INR) Amount (INR)

S.No. DESCRIPTION OF ITEM UNIT QUANTITY

DSR-2025 NDSR DSR-2025 NDSR

SH-28 Fire Alarm Work

Supplying, installation, testing & commissioning of main

control and indicating panel made out of 16 SWG MS sheet

to accommodate the following items duly powder coated in

approved colour with louvers for ventilation, locking

arrangement, audio and visual indication for fire alarm system, monitoring system

including connections, interconnections etc complete as required.

4 Zone panel for fire alarm system button for operation on 230V AC/24 V DC supply

conforming to IEC-268 for simplex mode of operation/communication Annoucement

1 28.1.10 control desk suitable for selection of different zones selectively and ON ALL CALL NOS 1 75,339.00 75,339.00

switch with visual indication etc. complete as required -1 set. Battery charger trickle cum

boost to take complete load of fire alarm system complete with all accessories including

providing & fixing of 2 nos.12 volt, 7 AH each sealed maintenance free batteries -1 set.

Supplying, installation, testing & commissioning of 1.5/3/6W metal box ceiling/wall

speakers complete as required.

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in

3 28.5.3 the existing surface / recessed steel conduit of following pairs, cores and size including

connections and interconnections etc. as required.

28.5.3.1 speaker cable Single pair, 2-core, 1.5 sqmm Mtr 50 61.00 3,050.00

Supplying, installation, testing & commissioning of manual call boxes of MS

4 28.1.3 construction in surface/recess with stainless steel chain & hammer assembly complete NOS 4 513.00 2,052.00

with glass and push button etc. as required.

Supplying, installation, testing & commissioning fire alarm sounder with facility to make

announcement, mounted in M.S. box (16 SWG) with hinged cover plate & suitable for

operation with amplifier i/c line matching transformer etc. complete as

Supplying & laying of 2x1.5 sqmm fire survival armoured cable, 600/1000V rated with

annealed copper conductor having glass mica fire barrier tape covered by an extruded

layer of Cross Linkable Ethylene Propylene Rubber (EPR) insulation and LSZH inner

bedding, steel wire armouring & LSZH outer sheath complete as required.

Supplying and fixing of following sizes of steel conduit along with accessories in

7 1.20.2 surface/recess including painting in case of surface conduit, or cutting the wall and Metre 250 289.00 72,250.00

making good the same in case of recessed conduit as required.-25 mm dia

SH-27 Fire Fighting Work

(a) Supplying, installation, testing and commissioning of electric driven terrace pump

conforming to IS 12469: 2019 suitable for automatic operation and consisting of

following, complete in all respects, as required: (Terrace Pump)

(b) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze

impeller with stainless steel shaft, mechanical seal as required.

(c)Suitable HP squirell cage induction motor TEFC type suitable for operation on 415

volts, 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal

foot mounted type with Class

8 27.4.2 'F' insulation, conforming to IS-12615: 2018.

(d) M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as

(e) Suitable cement concrete foundation duly plastered and with anti vibration pads.

Supply, installation, testing, and commissioning of a Fully Automatic Star-Delta Starter

suitable for a 12.5 HP (9.3 kW) 3-phase, 415V, 50Hz motor. The unit shall be enclosed in

9 NDSR a dust and vermin-proof powder-coated CRCA sheet steel enclosure complete in all EACH 1 18000 18,000.00

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming

to IS 1239/Class -II of IS: 3589 including Welding, fittings like elbows, tees, flanges,

tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable

10 27.7.7 clamp/support frame and painting with two or more coats of synthetic enamel paint of

required shade complete as required :

Supplying and fixing single headed internal hydrant valve with instantaneous

Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked

11 27.9 conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as

27.9.1 Single headed Gunmetal EACH 4 8208 32,832.00

Digitally signed by DEEPAK

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal

12 27.18 diameter size nozzle conforming to IS 903 suitable for instantaneous connection to

interconnect hose pipe coupling as required:

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and

13 27.16 female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office

red, conforming to IS 884 complete with the following as required.

(a) 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as

14 27.17 (b) 20 mm nominal internal dia gun metal globe valve & nozzle.

(c) Drum and brackets for fixing the equipmets on wall.

(d)Connections from riser with 25 mm dia stop gunmetal valve & M.S. Pipe and socket.

Supply and fixing of Fire hose box fabricated out of G.I. Sheet and frame, door shall be

750mm–1000mm width x 600mm height x 250mm depth. & fixed with 4 mm thick Glass,

suitable Rubber beeding and Locking arrangment. Quoted rate shall be included all

15 NDSR fasterners etc, and complete shutter shall be powder coated of approved colour both inside EACH 2 4950.00 - 9,900.00

Supply and fixing of Fire Shaft door fabricated out of G.I. Sheet and frame, door shall be

900mm x 1500mm min with double leaf. & fixed with 4 mm thick Glass, suitable Rubber

16 NDSR beeding and Locking arrangment. Quoted rate shall be included all fasterners etc, and EACH 2 12200.00 - 24,400.00

complete shutter shall be powder coated of approved colour both inside and out side.

17 NDSR Providing/Fixing Fire man axe. Each 4 1,400.00 - 5,600.00

CO2 type Fire exitinguisher ISI marked confirming to IS:15683 lates. Capacity 4.5 kg

complete with delivery hose horn, squeeze grip release valve, locking arrangement,

operating temperature -30°c to +55°c, supplied with body bearing IS 7285 mark and

approved valve as per IS 3224. Co2 Gas as per IS:15222. externally painted with PO Red

18 NDSR Shade No. 538 of IS 5, operation manual and floor stand or wall mount Bracket including - -

accessories as required as per site condition.

Powder Fire exitinguisher (stored Pressure Type) (Powder pressurized with dry nitrogen

gas at 15 bar) capacity 4kg duly ISI marked conforming to IS:15683:2006/latest, with IS

14609 ISI marked ABC powder complete with squeeze grip release valve, discharge pipe,

locking arrangment, pressure gauge, operation maual, Body Hydrotested at 35 bar,

19 NDSR operating temperature--30°c to +55°c, external epoxy powder coating with PO Red shade - -

No. 538 of IS 5, and floor stand or wall mount Bracket including accessories as required

as per site condition.

Supplying & fixing air vessel made out of 250 mm dia,8 mm thick MS sheet, 1200 mm in

height with air release valve on top and flanged connection to riser, drain arrangement

20 27.20 with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and Each 1 19,402.00 19,402.00

painting with synthetic enamel paint of approved shade as required.

Supplying and fixing of fire brigade connection of cast iron body with gun metal male

21 27.19 instantaneous inlet coupling complete with cap and chain as reqd. for suitable dia MS pipe -

connection conforming to IS 904 as required.

27.19.1 2 way-100 mm dia M.S. Pipe EACH 1 7262 7,262.00

Providing, installation, testing and commissioning of non-return valve of following sizes

confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, 5312 complete with

22 27.14 rubber gasket, GI bolts, nuts, washers etc.as required washers etc.as required : -

Providing, installation, testing and commissioning of butter fly valve of following sizes

confirming to IS: 13095 complete with rubber gasket, GI bolts, nuts, complete with rubber

23 27.23 gasket, GI bolts, nuts, washers etc.as required washers etc.as required :

Grand Total Carried over to summary 766975.00 101900.00

Grand Total Carried over to summary 766975.00 101900.00

Digitally signed by DEEPAK