Provisioning of Temporary Yoga shed in the Subhas Chandra park and renovation works in Gym at HAL Township Kanpur

HINDUSTAN AERONAUTICS LIMITED ACCESSORIES COMPLEX TRANSPORT AIRCRAFT DIVISION, KANPUR CIVIL WORKS DEPARTMENT

NAME OF THE WORK: Provisioning of Temporary yoga shed in the Subhas Chandra park and renovation works in Gym at HAL Township Kanpur. CONTRACT NO. MW/CIV/990/1/25-26

PRICE BID (Schedule A Bill of Quantity )

Name of the Tenderer:

Sl. No Specification Qty. Unit Rate in Figs [Excluding GST & Welfare cess] Rate in words Amount

1 The work in general shall be carried out as per CPWD DAR 2023. For item of works not covered in the CPWD DAR shall be governed as per BIS specification or as per Sound Engineering practice or as specified and directed by the EIC.

2 Contractors shall inspect the site and fully acquaint himself / themselves with the scope and nature of work, access, location and working condition. No claim will be considered later on the ground of ignorance or otherwise of the conditions under which the work will be have to be executed.

3 This BOQ specifications have to be read in conjunction with detailed technical specification and tender drawings if any.

4 The tenderer has to quote percentage above / below against the total amount considering the specified standard rates. If the contractor does not quote any percentage above / below on the total amount, the tender shall be treated as invalid and will not be considered.

5 The quoted percentage for the works mentioned below, shall be taken into consideration for evaluation of the tender. The lowest offer (L-1) will be determined considering the total amount including GST & Welfare cess based on the quoted percentage. HAL shall process the bills of contractor for executed work exclusive of GST & Welfare cess. In addition, payment towards GST & Welfare cess as applicable shall be made to the contractor along with the bills as per Bill Amount. The GST & Welfare cess paid by HAL shall be deposited to the concerned Govt. authority by the contractor regularly. Any other tax (as applicable) as imposed by the Govt. on the contract shall be borne by the contractor.

6 Contractors will be solely responsible for any accidents to workmen engaged by them during execution of work.

7 All materials required for the work will be contractors own supply. They shall conform to relevant IS standards and shall be of approved brand /manufacture as specified. If the specified brand/manufacture not available, then only alternative equivalent brand may be produced for approval. However, prior approval of HAL shall be taken before procurement of any material.

8 Any plant and machinery required are contractors own supply. No plant and machinery will be issued by HAL.

9 All the items shall be carried out as per the Specifications and as directed and approved by EIC.

10 The cement used in the work shall be of approved makes such as Jay Pee, Birla, ACC, Prism, Mycem or equivalent as approved by EIC.

11 Rate shall be inclusive of work at any height / level, lead & lift and staging, scaffolding etc.

12 Name & Address of the firm must be filled in the yellow shaded portion on the top of the page

1 Earth work in excavation by mechanical means (Hydraulic excavator)/ Manual means in foundation trenches and drains (not exceeding 1.5m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50m. All kind of soil all complete as directed & approved by EIC. 20.00 Cum 218.74 Rupees Two Hundred Eighteen and Seventy Four Paise 4374.80

2 Demolishing In cement mortar brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead etc. all complete as directed & approved by EIC. 5.00 Cum 1731.26 Rupees One Thousand Seven Hundred Thirty One and Twenty Six Paise 8656.30

3 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level PCC 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) all complete as directed & approved by EIC. 20.00 Cum 5724.37 Rupees Five Thousand Seven Hundred Twenty Four and Thirty Seven Paise 114487.40

4 Providing and laying of Reinforced cement concrete work (1:1.5:3) (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement etc. all complete as directed & approved by EIC. 10.00 Cum 9120.13 Rupees Nine Thousand One Hundred Twenty and Thirteen Paise 91201.30

5 Providing and applying Brick work with common burnt clay F.P.S. (non modular) bricks of class first designation 7.5 in foundation and plinth in Cement mortar 1:6 (1 cement : 6 coarse sand) etc. all complete as directed & approved by EIC. 25.00 Cum 5993.49 Rupees Five Thousand Nine Hundred Ninety Three and Forty Nine Paise 149837.25

6 Providing, rendering, screeding, dubbing out cement plaster in cement mortar 1:6 ( 1Cement : 6 Coarse sand) 12 mm average thickness, work upto at any height/depth on brick or concrete surfaces of any description fair / rough side, finishing fair trowelled to a smooth and even finish without using extra cement, including scaffolding, curing etc. complete as directed & approved by EIC. 150.00 Sqm 288.78 Rupees Two Hundred Eighty Eight and Seventy Eight Paise 43317.00

7 Providing and laying vitrified floor/ double charge tiles in sizes 600x600 mm (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., all complete as directed & approved by EIC. 75.00 Sqm 1305.42 Rupees One Thousand Three Hundred Five and Forty Two Paise 97906.50

8 Providing and laying Ceramic glazed floor tiles of size 300x300mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours shade, except white, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3kg/ sqm including pointing the joints with white cement and matching pigments etc., all complete as directed & approved by EIC. 25.00 Sqm 1105.29 Rupees One Thousand One Hundred Five and Twenty Nine Paise 27632.25

9 Supplying, fixing and fabricating MS structural MS Angle/ MS pipe/ MS flat etc.steel work riveted, bolted or welded in built up section trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer etc. all complete as directed & approved by EIC. 3500.00 Kg 112.35 Rupees One Hundred Twelve and Thirty Five Paise 393225.00

10 Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. etc. all complete as directed & approved by EIC. 95.00 Sqm 620.71 Rupees Six Hundred Twenty and Seventy One Paise 58967.45

11 Providing and fixing Ist quality ceramic glazed wall tiles size (300x450)mm conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.: 60.00 Sqm 1065.50 Rupees One Thousand Sixty Five and Fifty Paise 63930.00

12 Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid etc. all complete as directed & approved by EIC. 3.00 Each 6728.24 Rupees Six Thousand Seven Hundred Twenty Eight and Twenty Four Paise 20184.72

13 Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : (15 mm nominal bore) etc. all complete as directed & approved by EIC. 5.00 Each 425.88 Rupees Four Hundred Twenty Five and Eighty Eight Paise 2129.40

14 Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. Internal work - Exposed on wall 15 mm dia nominal bore etc. all complete as directed & approved by EIC. 80.00 Rm 307.90 Rupees Three Hundred Seven and Ninety Paise 24632.00

15 Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. Internal work - Exposed on wall 20 mm dia nominal bore etc. all complete as directed & approved by EIC. 50.00 Rm 367.48 Rupees Three Hundred Sixty Seven and Forty Eight Paise 18374.00

16 Providing and fixing G.I. pipes complete with G.I. fittings and clamps, including cutting and making good the walls etc. Internal work - Exposed on wall 25 mm dia nominal bore etc. all complete as directed & approved by EIC. 40.00 Rm 463.61 Rupees Four Hundred Sixty Three and Sixty One Paise 18544.40

17 Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. 15 mm nominal bore etc. all complete as directed & approved by EIC. 15.00 Each 563.40 Rupees Five Hundred Sixty Three and Forty Paise 8451.00

18 Providing and placing on terrace (at all floor levels) polyethylene water storage tankof three layer, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. etc. all complete as directed & approved by EIC. 500.00 litre 9.24 Rupees Nine and Twenty Four Paise 4620.00

19 Providing & applying two coat of first quality synthetic enamel paint of approved make such as Asian Paints, Berger,I, Nerolac, Snowcem, Apex on wood/ steel/ concrete surface of any description any girth to give an even shade including preparing the old suface by rubbing with coarse grained sand paper, filing the crevices and holes with kniffing filler paste, of approved quality for wood work as per IS :3585 at all levels as specified and directed by the EIC. 200.00 Sqm 86.39 Rupees Eighty Six and Thirty Nine Paise 17278.00

20 Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps etc. all complete as directed & approved by EIC. 3.00 Each 2225.92 Rupees Two Thousand Two Hundred Twenty Five and Ninety Two Paise 6677.76

21 Providing and applying Birla white/JK white/ Latafinish/ Myklaticate wall care putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth etc. complete as per direction of the Engineer-in-Charge. 350.00 Sqm 131.13 Rupees One Hundred Thirty One and Thirteen Paise 45895.50

22 Providing & applying two coats of First quality Premium Acrylic Distemper (Distemper oil emulsion)/ Oil Bound distemper of approved colour and make like Asian / Berger/ Nerolac conforming to IS-428 to ceiling, internal wall, beams and columns including preparation of old surfaces by scrapping and rubbing the plastered surface with sand paper and finishing smooth with proper putty work including cleaning the dirt & other impurities etc the rates are including renoving of old colour & making wall surface good (if required ) . complete as directed and approved by EIC. Note:- Required approved oil bound distemper @ 1Kg for 07 Sqm for two coats. 200.00 Sqm 52.69 Rupees Fifty Two and Sixty Nine Paise 10538.00

23 Providing and Applying Finishing walls with Acrylic Smooth Exterior Paint of required shade : New Work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 liter/10 sqm). All complete as directed & approved by EIC. 200.00 Sqm 134.96 Rupees One Hundred Thirty Four and Ninety Six Paise 26992.00

24 Providing and fixing factory made uPVC door frame (Extruded section profile size 48x40mm) made of uPVC extruded sections having an overall dimension as below (tolerance ±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of Engineerin-charge. 20.00 Rm 227.06 Rupees Two Hundred Twenty Seven and Six Paise 4541.20

25 Providing and fixing to existing door frame 24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-in-charge. (For W.C. and bathroom door shutter). 6.50 Sqm 2495.17 Rupees Two Thousand Four Hundred Ninety Five and Seventeen Paise 16218.61

26 Providing and fixing on wall face unplasticised rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. for 110mm diameter etc. all complete as directed & approved by EIC. 40.00 Rm 317.14 Rupees Three Hundred Seventeen and Fourteen Paise 12685.60

27 Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. for 110mm bend etc. all complete as directed & approved by EIC. 12.00 Each 126.34 Rupees One Hundred Twenty Six and Thirty Four Paise 1516.08

28 Steel reinforcement ( Thermo mechenically treated bars of grade Fe 500 D or more ) for R.C.C. work ready to use cut and bend rebars of approve make from factory / work shop to constrction site including placing in position and bending all complete above plith level / upto plith level etc. all complete as directed & approved by EIC. 300.00 Kg 83.74 Rupees Eighty Three and Seventy Four Paise 25122.00

29 Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. (80 mm thick C.C. paver block of M-35 grade with approved color design and pattern.) etc. all complete as directed & approved by EIC. 60.00 Sqm 917.23 Rupees Nine Hundred Seventeen and Twenty Three Paise 55033.80

30 Dismantling tile work in floors and wall laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles above 10 mm to 25 mm etc. all complete as directed & approved by EIC. 75.00 Sqm 61.68 Rupees Sixty One and Sixty Eight Paise 4626.00

31 Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead of area 3 sq. metres and below etc. all complete as directed & approved by EIC. 10.00 Each 308.57 Rupees Three Hundred Eight and Fifty Seven Paise 3085.70

32 Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. etc. all complete as directed & approved by EIC. 50.00 Sqm 45.92 Rupees Forty Five and Ninety Two Paise 2296.00

33 Supply and Laying of 4.5mm thick PVC Vinyl Flooring make of Responsive/ Armstrong/ Mannington including chemical used for laying, wastage, joints cods, required over laping T & P etc. complete as directed & approved by EIC. 1. Prepration of surface (Sub-floor) including Filling of small pits and level properly. 2. Installing of flooring work will be execute specialized team. 3.Making surface lining of court, with material etc 4. Measurment will be taken in the flat sqft area. Note- Sample got approved by EIC, before laying. 1300.00 Sqft 150.00 Rupees One Hundred Fifty Only 195000.00

34 Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately. Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for : (i) Sites with basic wind speed > 45 m/sec as per IS 875 – Part 3 (ii) Sites with structure height more than 20m for all wind speeds Casement door double panel with French (False) Mullion with zinc alloy (zamak) 3D hinges, multi-point locking system with cylinder, zinc alloy (zamak) powder coated handles on both sides. Using R3 series with frame (55 mm & above) x (50mm & above) & sash (55 mm & above) x (85mm & above) & French (False) mullion (55 mm & above) x (60mm & above). (Height upto 2.5 metre). 16.00 Sqm 10003.15 Rupees Ten Thousand Three and Fifteen Paise 160050.40

35 Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by EIC. Two track two panels sliding window with aluminium channel for roller track, nylon rollers with SS 304 body. Using R4 series with frame (64 mm & above) x (45 mm & above) & sash (44mm & above) x (55 mm & above) with zinc alloy (zamak) powder coated handle on every panel along with multi-point locking system (Height above 1.8m) 20.00 Sqm 8091.26 Rupees Eight Thousand Ninety One and Twenty Six Paise 161825.20

36 Supply and fixing 5-6 mm thick WPC Fluted wall panelling (Best Quality) of make century/ Green ply/ Alutuff etc. & WPVC wall louvers (Best quality) of make Hitech/ Rayan panel for internal walls the thickness of panel is 8-10 mm and width of panel is 300mm, WPC wall panelling height as per requirement fixing on the wall width of panel 100 to 300 mm as per requirement it is heighly resistent to moisture water and insects, it is low maintenance product. The rates are including all labour, T & P required fitting wastage etc. Note- (1) Sample to be approved by EIC, before start of work. (2) Design and fixing area of WPC fluted pannels & WPC louvers also dericted by EIC. 320.00 Sqm 1500.00 Rupees One Thousand Five Hundred Only 480000.00

37 Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board of make saint gobin /USG kanauf etc. to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with priming coat of primer and two coat of apex paint : (12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks) etc. complete as directed & approved by EIC 125.00 Sqm 1978.70 Rupees One Thousand Nine Hundred Seventy Eight and Seventy Paise 247337.50

38 Providing and laying gang saw cut 18 mm thick, mirror polished pre moulded and pre polished machine cut granite stone of required size and shape of approved shade, colour and texture in footpath, flooring cut granite stone of required size and shape of approved hade, colour and texture in footpath, flooring in road side plazas and similar locations, laid over 20mm thick base of cement mortar 1:4 (1cement : 4 coarse sand) including grouting the joints with white cement mixed with matching pigment, epoxy touch ups etc. Granite stone slab of colour black, cherry/ Ruby red area of slab over 0.50 sqm. complete as per direction of Engineer-in-Charge. 17.00 Sqm 4316.22 Rupees Four Thousand Three Hundred Sixteen and Twenty Two Paise 73375.74

Sub-Total (Excluding GST & Welfare cess) Rupees Twenty Seven Lac Five Hundred Sixty Five and Eighty Five Paise 2700565.86

The Tenderer has to Quote Percentage Above / Below as Specified and Percentage Shall be Quoted in Figures. Approximate Amount Put to Tender State Above or Below Quoted Percentage in Figures [Excluding GST & Welfare cess] Quoted Amount

Tenderer's Quote (Excluding GST & Welfare cess) 2700565.86 BELOW % 2700565.86

Add 18% GST Rupees Four Lac Eighty Six Thousand One Hundred One and Eighty Five Paise 486101.85

Add 1% Welfare Cess Rupees Twenty Seven Thousand Five and Sixty Five Paise 27005.66

Grand Total (Including GST& Welfare cess) Rupees Thirty Two Lac Thirteen Thousand Six Hundred Seventy Three and Thirty Six Paise 3213673.37

Note: The tenderer has to quote percentage above / below against the total amount considering the specified standard rates. If the contractor does not quote any percentage above / below on the total amount, the tender shall be treated as invalid and will not be considered.

WARNING: PLEASE ENTER PERCENTAGE QUOTE

HINDUSTAN AERONAUTICS LIMITED

ACCESSORIES COMPLEX

TRANSPORT AIRCRAFT DIVISION

CIVIL WORKS DEPARTMENT

ISSUED TO MR/MESSRS. SCHEDULE ‘A’ BILL OF QUANTITIES Sub: “Construction of Oil & Lubricant/ Chemical/ Consumable store at HAL Factory Kanpur.” Cont. No. : MW/CIV/370/1/14-15 Note : Sqm. denotes Square Meters Cum denotes Cubic Meters MT denotes Metric Tonnes Rm denotes Running Meters Ltr denotes Litres Kgs denotes Kilograms.

1. The work in general shall be carried out as per MES SSR 2010 . For item of works not covered in the SSR shall be governed as per BIS specification or as per Sound Engineering practice or as specified and directed by the Engineer-in-Charge.

2. The quoted rates shall be for the net finished work / item inclusive of cost of all necessary materials, machinery, tools and plant in all the operations described in the BOQ at all heights etc. All the required tests shall be carried out by the contractor at their cost in the presence of Engineer-in-Charge or his authorized representative and shall submitt the test results to the Engineer-in-Charge. If the test are carried out at an outside laboratory, the cost of such tests, materials, transportation, etc., shall be borne by the Contractor.

3. Contractors shall inspect the site and fully acquaint himself / themselves with the scope and nature of work, access, location and working condition. No claim will be considered later on the ground of ignorance or otherwise of the conditions under which the work will be have to be executed.

4. Contractors will be solely responsible for any accidents to workmen engaged by them during execution of work.

5 The rates quoted shall be inclusive of all taxes such as Sales Tax/VAT, Turnover Tax, Entry Tax, Service Tax (Contractor's portion as per the existing or amended rules from time to time), Sales Tax on Works Contract and all duties and levies like royalty, cess etc. HAL shall not reimbuse any taxes to the contractor under any circumstances. 5.1 RECOVERY OF SALES TAX/VAT AT SOURCE Sales Tax on works Contract will be recovered as per the rates indicated in UP Sales Tax act. The applicable sales Tax of the Gross value shall be deducted as per the provision of Law and the same will be remitted to the Tax Authorities on monthly basis. A certificate to this effect will be issued to the Contractors.

6. All materials required for the work will be contractors own supply. They shall conform to relevant IS standards and shall be of approved brand /manufacture as specified. If the specified brand/manufacture not available, then only alternative equivalent brand may be produced for approval. However, prior approval of HAL shall be taken before procurement of any material.

7. Bull dozers, power shovel, graders, loaders, Power road rollers, vibratory rollers, sheep foot rollers, and any other plant and machinery required are contractors own supply. No plant and machinery will be issued by HAL.

8.The Contractor may use Ready Mixed Concrete (R.M.C) without claiming for any extra cost subjected to satisfying the following conditions. The agency, which supplies R.M.C to be got approved by HAL.

9. For antitermite treatment and water proofing work contractor's has to furnish performance guarantee bond for five years on non judical stamp paper of Rs 100.00. Defect laibility of such items will be released after completion of guarantee period.

10. All the items shall be carried out as per the Specifications and as directred and approved by EIC.

HINDUSTAN AERONAUTICS LIMITED

TRANSPORT AIRCRAFT DIVISION-KANPUR

Sub: “Construction of Oil & Lubricant/ Chemical/ Consumable store at HAL Factory Kanpur.”

Cont. No. : MW/CIV/370/1/14-15

S.N. Description of Item Freak Item Qty. Unit Rate per unit in Figures Rate per unit in Words Amount (In Rs.)

1 Earth work in excavation in ordinary soil in trenches, not exc.1.50m depth and of any width, for foundation & other similar allied works etc. including cost of dressing / trimming sides and leveling / grading and ramming of bottoms of excavation, dewatering etc if required, getting out and return filling with excavated earth in layers of not exceeding 25cm thick including watering consolidating etc. & disposing the surplus excavated earth in the low lying area of factory within a lead of 500 mtrs etc. complete as directed &approved by EIC. (-) 275.00 Cum 100.00 Rupees One Hundred Only 27500.00

2 Providing and laying Plain cement concrete in 1:4:8 (1Cement : 4 Coarse sand: 8 stone aggregate of 40 mm nominal size) in foundation, floor or any description of work including cost of all operations such as manual / mechanical mixing, placing, compacting, scaffolding, side shuttering, curing etc . Complete as directed by EIC. 25.00 Cum 4000.00 Rupees Four Thousand Only 100000.00

3 Providing and laying brick work in walls, pillars, fascia, drain etc. in cement mortar 1:6 (1 cement : 6 coarse sand) in well burnt clay bricks, First class bricks, straight or curved in plan of any radius, in foundation and super- structure, work up to any height or depth including cost of scaffolding , raking out joints up to 1 cm depth as the work proceeds, curing etc. complete in all repect as per specification and direction of EIC. (+) 100.00 Cum 5000.00 Rupees Five Thousand Only 500000.00

4 -- do-- but half brick thick wall in CM 1:4. All complete as directed and approved by EIC. (+) 50.00 Sqm 700.00 Rupees Seven Hundred Only 35000.00

5 Providing, rendering, screeding and dubbing out plaster in cement mortar 1:3 (1cement: 3 Coarse Sand) of 5 mm thick on concrete surfaces at any height / depth of ceilings, column, beams, staircase, fins, fascia , drop etc. including trowelled to smooth and even finish without using extra cement, including cost of surface preparation, required scaffolding, curing etc. complete as directed & approved by EIC. 105.00 Sqm 150.00 Rupees One Hundred Fifty Only 15750.00

6 Extra over rendering or plastering for work in isolated widths or in widths not forming part of general plastering such as in bands, sunk panels, cornices, skirting, drip moulds and similar work not exceeding 15cm in width or grith; including cutting to edges, all mitres and stopped ends etc. all complete as directed and approved by EIC. 120.00 RM 40.00 Rupees Forty Only 4800.00

7 Supplying and fixing in position steel reinforcement (TMT bars) conforming to IS-1786-1985 of any dia of approved make such as TATA/SAIL/ISPAT/VIZAG for slabs, beams, columns, footing or any other similar description of work, including cut to length, bent to shape as required, cranking bending , spirally or hooping, hooking ends and binding with mild steel wire soft drawn of not less than 0.9 mm dia, securing with chairs, placing in position and maintaining firmly so that placing and ramming of concrete will not displace it, removing rust and scales if any, wastage, etc. complete as directed & approved by EIC (Test report of manufacturer is to be submitted along with the supply). 12500.00 Kg 62.00 Rupees Sixty Two Only 775000.00

8 Providing and laying R.C.C 1:1 1/2:3 (1Cement : 11/2 Coarse sand: 3 stone aggregate of 20 mm nominal size) for foundation, beam, columns, lintels etc. or any description of work including manual / mechanical mixing, placing, compacting, lead & lifts, curing etc . Complete as directed by EIC. 70.00 Cum 6000.00 Rupees Six Thousand Only 420000.00

9 Providing and laying Ready Mixed cement Concrete ( Design Mix M-25 grade ) in slab, floor, pavments or simlar items, RMC (Ready Mixed Cement Concrete M- 25 grade, using 20mm graded granite aggregate and consolidated with mechanically vibrated needle and surface /screed vibrators and curing. Design mix to be got approved from EIC. If any additional quantity of cement over and above the minimum quantity of 300 Kgs per Cum is required as per the design mix/trial mix to achieve the specified strength, cost of the same shall be borne by the contractor. Note: Design Mix to be got approved by EIC before the work. 70.00 Cum 7000.00 Rupees Seven Thousand Only 490000.00

10 Providing and laying Plain cement concrete 1:2:4 (1 cement :2coarse sand : 4 stone coarse 12.5mm aggregate downgraded) 25mm thick in drain foundations, floors or in any description of including manual / mechanical mixing, placing, compacting, curing scaffolding, form work finishing the surface even and smooth using extra cement all complete as directed & approved by EIC. (+) 65.00 Sqm 300.00 Rupees Three Hundred Only 19500.00

11 Supplying & fixing two track powder coated glazed Aluminium bombay sliding window all complete with outer frame of 63 x 38 x 2 mm Aluminium section and two track channel (Bottom / top &sides) of size 62 x 32 x 1.2mm, sliding shutters made of special Bombay sliding window section 38 x 19 x 1.2mm, All complete with 5mm thick float glass of MODI/ SAINT GOBAIN, edges wrapped in rubber beading, two nos roller of flyrail , including providing and fixing powder coated aluminium grill , powder coated Aluminium Handle & locking arrangement etc. all , complete with labour material, wastage etc. all complete as directed & approved by EIC. (-) 25.00 Sqm 4000.00 Rupees Four Thousand Only 100000.00

12 Providing and fixing powder coated Aluminium grill having weight not less than 2.0 Kg/m2 of approved make such as (HINDALCO/JINDAL/INDAL) of approved design to the existing outer frame of Bombay sliding window including required fittings such as 'Y' channel all around the frame for properly securing the aluminium grill including circular cutting wherever directed for provision of Air cooler, all complete with cutting wastage etc. compete in all respect as per specification and direction of EIC . (+) 5.00 Sqm 3000.00 Rupees Three Thousand Only 15000.00

13 Providing, manufacturing and erecting partly glazed and partly panelled powder coated Aluminium parititions using standard sections of JINDAL, HINDALCO or equivalent as per approved design and drawing with bottom panel of 12mm thick prelaminated exterior grade particle board of reputed manufacturers such as Archid, Kitlam, Century confirming to 12823 and top panels with 5mm thick float glass as detailed below including necessary cleats, Screws, fastners etc., a) Top, middle, vertical and bottom members -100x 44 x2mm of weight 1.519Kg / RM forming grid not exceeding 1.00 Sqmt panel as approved. b) Glass - 5.00mm thick plain float glass of MODI / SAINTGOBAIN or equivalent c) Bottom Panels 12mm thick prelaminated exterior grade in top panal particle board. d) Rubber gaskets - Good quality of approved make e) Glazing clips - Weight of 0.097Kg/RM. (+) 10.00 Sqm 3500.00 Rupees Three Thousand Five Hundred Only 35000.00

14 Providing, manufacturing & fixing partly glazed partly panelled powder coated Aluminum hinged single doors with door frame shutter of approx. size 1.00 x 2.00 m of extruded section of JINDAL/HINDALCO with door frame section 100 x 44 x 2mm, vertical members, top and middle rails of door shutter of 83 x 44 x 2mm, bottom rail of door shuter of 114 x 44 x 2mm section, fixing the door to the wall with rawplugs and screws incluiding providing and fixing MS tie rod of 8mm for the door shutter, all as directed and approved be EIC. The quoted rate shall be inclusive of supplying and fixing following fixtures for each shutter. a) Aluminium body hydraulic door closer universal type of Everite / Hardwin or equivalent. 1 No. b) Powder coated Aluminium towerbolt of 200 mm long of extruded section (ISI marked only) 2 Nos. c) -----------do -----------Aldrop 250mm long 1 No. d)Internal locks of approved make 1 No. e) Powder coated Aluminium alloy handles fabricated type American 150mm ISI marked only 2 Nos. f) Aluminium powder coated butt hinges 100 mm long ISI marked 4 Nos. g) 5mm thick float glass of MODI/ SAINT GOBAIN for the upper portion of the door with good quality rubber beadings, powder coated Aluminum glazing chips. h) 12mm thick both sided pre-laminated exterior grade particle board confirming to IS 12823 of NOVAPAN/GREENLAM/FORMICA/SANDIK/SWARAJ or equivalent (ISI marks) for the lower portion of door shutter (approx. 1.00 mtr height) using powder coated Aluminium glazing clips, beading etc.as directed & approved by EIC. 25.00 Sqm 5000.00 Rupees Five Thousand Only 125000.00

15 Supplying & fixing acid proof non skid ceramic tiles of size 400x400mm x 9 mm thick (Approx size) in floor etc of Kajaria, Johnson & Johnson, Orient Bell, Somany, Nitco make etc of first quality (tiles sample as approved by EIC) for floors including providing and laying 15 mm nominal thick cement mortar screed bedding layer of CM 1:4 ( 1 cement : 4 coarse sand ) and fixing tile with cement slurry, over the existing floor, and preparation of surface by wire brush cleaning and wetting the surface with water and spreading cement slurry, including cost of raking the joints and pointing with tinted white cement, curing, cleaning including cutting of tiles, wastage and disposal of debris at directed place etc. complete as directed by EIC. [Note:- Tile sample to be got approved by EIC before laying]. (-) 250.00 Sqm 1300.00 Rupees One Thousand Three Hundred Only 325000.00

16 Supplying and fixing glazed ceramic wall tiles of first quality of reputed manufacturers such as Kajaria, Johnson & Johnson/ Orient Bell/ Somany/ Nitco tiles in dado and skirting of size (450x350x 7)mm thick or bigger size with 10 mm thick cement mortar screed bedding layer 1:4 ( 1 cement : 4 coarse sand ) cost of raking the joints and pointing with white cement mixed with matching tint finishing wall ( matching with floor tiles colour) / make all complete as directed & approved by EIC. (+) 50.00 Sqm 1300.00 Rupees One Thousand Three Hundred Only 65000.00

17 Providing & laying ultra tiles VENTURA-T of size 300 x 300 mm of approved design and shade in Treads and laid over 15mm thick cement mortar 1:4 bedding layer jointing with cement slurry matching the shade & pointing with white cement & pigment complete with labours, material wastage etc. as directed & approved by EIC. 10.00 Sqm 1300.00 Rupees One Thousand Three Hundred Only 13000.00

18 --do-- but VENTURA-R of size 152 x 300 mm for staircase risers over 15mm thick cement mortar in CM 1:4 complete all as directed & approved by EIC. (+) 5.00 Sqm 1300.00 Rupees One Thousand Three Hundred Only 6500.00

19 Providing & applying two coats oil bound distemper of approved colour with one coat of alkali resistant primer all of approved make such as Asian / Berger/ ICI or equivalent conforming to IS 428-1969 to walls, ceiling or of any description at any height, including providing and applying Birla white/Latafinish/JK white wall putty as per requirement of site for making surface even and smooth complete with cost of all materials, labour, wastage, safety measures, scaffolding, staging etc. as directed & approved by EIC. (+) 580.00 Sqm 150.00 Rupees One Hundred Fifty Only 87000.00

20 Providing & Applying two coat of premium acrylic silicon based weather resistant exterior paint including one coat of exterior primer such as weather coat long life / weather shield / Apex of reputed manufacturer including providing and applying Birla white/Latafinish/JK white/Myklatirat wall putty @ 0.40 Kg / Sqm for making surface even and smooth. All complete with labour, material ,required scaffolding, brushes and other tools & plants required for proper completion of work cleaning the splashes from door, windows and from other surfaces etc.complete as directed & approved by EIC. (+) 500.00 Sqm 150.00 Rupees One Hundred Fifty Only 75000.00

21 Supplying and fixing 110mm PVC, SWR single socketed pipe in any length with rubber ring joint laid in trenches or in floors for soil waste of approved make such as Supreme Kisan, Finolex, Prince or equivalent Conforming to IS: 4985-2000;(Class - 4) of complete with all required necessary fittings for fixing etc. complete as directed & approved by EIC . (-) 50.00 RM 200.00 Rupees Two Hundred Only 10000.00

22 Supplying and fixing PVC (SWR) bends of 110mm with access door socketed of Supreme, kisan, Finloex, Prince (ISI make) etc complete as directed & approved by EIC. (-) 10.00 Each 100.00 Rupees One Hundred Only 1000.00

23 Sand filling under floors or in foundations including watering and consolidation, complete as directed & approved by EIC. (-) 15.00 Cum 100.00 Rupees One Hundred Only 1500.00

24 Supplying & filling with aggregates of gauge 40 to 80mm broken stone or boulders in pits/ wells in layers including lead, lift, T & P etc. complete as directed & approved by EIC. (+) 10.00 Cum 2500.00 Rupees Two Thousand Five Hundred Only 25000.00

25 Drilling of 200mm dia boring hole 2m deep from ground level in soil including all tools & machinery and disposal of spoil upto a lead of 50m within the premises of factory etc. complete as directed & approved by EIC. (+) 1.00 Each 2000.00 Rupees Two Thousand Only 2000.00

26 Drilling of boring hole 200mm dia after 2 meter depth including all tools & machinery tools and disposal of spoil upto a lead of 50m within the premises of factory etc. complete as directed & approved by EIC Rate also included for making strata chart to be made for making slots in ribbed pipe. (+) 38.00 RM 1000.00 Rupees One Thousand Only 38000.00

27 Supplying & fixing 160mm dia PVC pipe of pressure rating 6 kg/ cm2 of approved make such as Supreme / Finolex / Prince (ISI make) with socket and fittings for complete job etc. complete as directed & approved by EIC. (-) 35.00 RM 250.00 Rupees Two Hundred Fifty Only 8750.00

28 Supplying & fixing 160mm dia PVC ribbed screen sloted pipe of pressure rating 6kg/ cm2 of approved make such as Supreme / Finolex /Prince (ISI make) with socket and fittings for complete job etc. complete as directed & approved by EIC. (Slot will be made in accordance with strata chart). (-) 6.00 RM 250.00 Rupees Two Hundred Fifty Only 1500.00

29 Providing & applying flush pointing in CM 1:3 in brick wall including raking out joints complete as directed & approved by EIC. (+) 50.00 Sqm 1000.00 Rupees One Thousand Only 50000.00

30 Supplying & Fixing cast iron work grade FG 150, unmachined, in gratings and similar articles exc. 5.00kg/each and as directed by EIC. (+) 2500.00 Kg 140.00 Rupees One Hundred Forty Only 350000.00

31 Providing, rendering , screeding and dubbing out in cement mortar 1:6 (1cement: 6 graded coarse sand)10mm thick, on rough or fair faces of brick/ concrete surfaces at any height / depth on wall, ceiling, fascia, etc. including trowelled to smooth and even finish without using extra cement, including cost of surface preparation , scaffolding, curing etc. complete as directed by EIC. (+) 1000.00 Sqm 180.00 Rupees One Hundred Eighty Only 180000.00

32 Supplying & fixing non-skid ceramic tiles of approx. size 400x400mm x 7-9 mm thick in floor, of reputed manufacturers such as Kajaria, Johnson & Johnson, Orient Bell, Somany, Nitco make of first quality , including providing and laying 15 mm nominal thickness cement mortar screed bedding layer of CM 1:6 ( 1 cement : 6 coarse sand ) and fixing tile with cement slurry and preparation of surface by wire brush cleaning and wetting the surface with water and spreading cement slurry. including cost of raking the joints and pointing with tinted white cement, curing, cleaning the tiles, including cutting of tiles, wastage and disposal of debris at directed place etc. complete as directed & approved by EIC. [Note:- Tile sample to be got approved by EIC before laying]. 12.00 Sqm 1300.00 Rupees One Thousand Three Hundred Only 15600.00

33 Supplying and fixing glazed ceramic wall tiles of first quality of reputed manufacturers such as Kajaria, Johnson & Johnson/ Orient Bell/ Somany/ Nitco tiles in dado and skirting, of size (450x350x 7)mm thick with cement slurry over sub- base of 10 mm thick cement mortar 1:4 ( 1 cement : 4 coarse sand ) cost of raking the joints and pointing with white cement mixed with matching tint finishing wall ( matching with floor tiles colour) / make all complete as directed & approved by EIC. 50.00 Sqm 1300.00 Rupees One Thousand Three Hundred Only 65000.00

34 Supplying and fixing in position set of coloured Glazed Vitreous China make oval shaped counter top wash Basin of Parryware or equivalent (design & colour as approved by EIC) of size 550 x 450 mm approx. including cost of 32 mm dia CP brass waste coupling, CP swan neck pillar cock, CP angle valve, CP bottle trap all CP fittings of Parryware / Plumber or equivalent make , complete in all respect as directed & approved by EIC. (+) 2.00 Each 8000.00 Rupees Eight Thousand Only 16000.00

35 Supplying and fixing urinal partition black granite on both side finish 18 - 20mm thick machine cut of size 90 cm X 50 cm (approx.) or required size to bedded and jointed grouted on wall in CM 1:2 and finishing edges with white cement and admixture pigment to match the shade of granite stone including cutting forming, round edge beading moulded in granite with polish complete in all respect including all labour, materials, T& P as per direction of EIC. 1.50 Sqm 2500.00 Rupees Two Thousand Five Hundred Only 3750.00

36 Supplying and fixing Red granite wash basin platform 20mm thick, one side polished, machine cut of required size to accommodate two oval shape wash basins, including making oval shape opening for two W.B. as per size of wash basin providing and laying bedding mortar in CM 1:4 , 15 mm and finishing & polishing the edges of granite and pointed with pigmented white cement to match the shade of granite stone including cutting forming, round edge beading moulded in granite with polish complete in all respect including all labour, materials, T& P as per direction of EIC. (-) 1.00 Sqm 2500.00 Rupees Two Thousand Five Hundred Only 2500.00

37 Providing and Fixing coloured Vitreous Chinaware coloured new magnum Urinal of Parryware or equivalent of size 635mmX395mmX420mm complete with providing and fixing plugs, bedding urinals in wall in cement mortar 1:2 ( 1 cement : 2 coarse sand), securing urinals to plugs with 60 mm long S.S screws, pointing around urinals back in cement. Complete with the following system:- (a) Providing & fixing 50mm PVC Pipe supreme make or equivalent about 750mm long concealed vertically in wall & reparing the wall with CM (1:3). (b) Providing & fixing CP Brass waste couplings and jointing with waste pipe & put in concealed pipe. (c) Providing & fixing 15mm CP Brass half turn fancy flush cock, to water line including all fittings fixture with CP Cover plate. (d) Providing & fixing CP spreader of make Parryware or equivalent 15mm dia with CP Pipe connector to urinal, all complete with required fitting & fixture T- elbow, Grating of C.P. Union, jointer connector etc. for proper functioning of urinal complete in all respect as directed & approved by EIC. (+) 3.00 Each 8000.00 Rupees Eight Thousand Only 24000.00

38 Supplying & Fixing in position coloured European Water Closet of vitreous china with 'P' or 'S' trap left or right bent of Parryware make or equivalent as per direction of EIC, with plastic seat cover and lid fixed with CP brass hinges and rubber buffers. Fixing of 10 litre capacity Plastic flushing cistern of Parryware Deluxe model make complete with all accessories such as inlet, ball valve, float, 15 mm dia PVC pipe connection,40 mm dia PVC flush pipe bent to shape with necessary connections, fittings and clamps PVC connection with union 15 mm dia overflow pipe with specials, providing and fixing 15 mm dia GI connections, GI over flow pipe with specials including cutting chases and finishing in walls after embedding of pipes , floors etc , where required with Cement mortar 1:3 ( 1cement: 3coarse sand )all complete including cost of painting of brackets( with red oxide primer and two coat of synthetic enamel paint). 1.00 Each 7000.00 Rupees Seven Thousand Only 7000.00

39 Supplying & Fixing factory made PVC solid panel door shutter 30 mm thick of approved manufacturer such as Rajshri Plastiwood/ Syntex/Polypan or equivalent brand factory made solid panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mmx19 mm for stiles & 15 mm x 15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame shall be covered with 5 mm thick heat moulded Rajshri /Syntex/Polypan PVC 'C' channel of size 30x50 mm forming stiles, and 5 mm thick, 75 mm wide PVC sheets for top rail, lock rail & bottom rail on either side, and 10mm (5mmx2) thick, 20mmwide cross PVC sheet as gap insert for top rail & bottom rail. Panelling of 5 mm thick PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with 30 mm wide x5mm thick PVC sheet beading on either side, and join together with solvent cement adhesive.. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' channel using PVC solvent cement adhesive etc. complete as per direction of E -I-C, manufacturer's specification & drawing. Including all fittings such as aluminum tower bolt 150mm long 2 Nos.: Sliding door bolt 200mm long 1No & aluminum handle 100mm long 2no in each shutter as directed & approved by EIC. 4.20 Sqm 2800.00 Rupees Two Thousand Eight Hundred Only 11760.00

40 Supplying & Fixing factory made polyvinyl chloride (PVC) Door Frame of approved manufacturer such as Rajshri Plastiwood / Syntex/ Polypan of size 50x47mm with a wall thickness of 5mm, made out of extruded 5mm rigid PVC foam sheet, mitre cut at two corners and joined with 2 nos. of 150 mm long brackets of 15x15mm M.S. Square tube. The two vertical door profiles are to be reinforced with 19x19 mm M.S. Square tube of 19 gauge,EPDM rubber gasket weather seal to be provided through out the frame. The door frame shall be fixed to the wall using 65/100 mm long M.S. Screws through the frame by using PVC fasteners. A minimum of 4 nos. of screws to be provided for each vertical member & minimum 2nos. For horizontal member etc. complete as per manufacturers specification and direction of EIC. 15.00 Rm 500.00 Rupees Five Hundred Only 7500.00

41 Supplying & Fixing in position tilling /adjustable type LOUVERS of size 600 x 600mm, Louver strip fixed over aluminium frame made of powder coated aluminium section of 63 x 38 x 2mm and fixing of 3.00mm thick and 100 mm wide pinheaded glass strip etc. Complete as directed and approved by EIC. (-) 2.00 Each 200.00 Rupees Two Hundred Only 400.00

42 Supplying & Fixing Aluminium powder coated barrel tower bolt 200 mm long size of extruded section of approved qualtiy (ISI mark) with all accessories which is required and complete in all respect as directed & approved by EIC. (+) 6.00 Each 200.00 Rupees Two Hundred Only 1200.00

43 Supplying & Fixing Aluminum powder coated 150 mm long Handles (dull finish cast type of good quality having ISI mark) to each door shutter all complete as directed & approved by EIC. (+) 6.00 Each 125.00 Rupees One Hundred Twenty Five Only 750.00

44 Providing and fixing medium weight, cold rolled steel Butt hinges of 100 mm size fixed with screws for doors, windows etc. all complete with labour, material and fixing to wooden / MS frame, making cut outs in wooden frame for fixing hinges etc. complete as directed by EIC. 12.00 Each 50.00 Rupees Fifty Only 600.00

45(a) Supplying and Fixing of CP brass two way bib cock for 15 mm dia pipe of Plumber / GEM / L&K or equivalent approved make, including jointing with water supply lines, complete as directed by EIC . (+) 2.00 Each 1700.00 Rupees One Thousand Seven Hundred Only 3400.00

(b) Supplying and Fixing of CP brass long body fancy type bib cock for 15 mm dia pipe of Plumber / GEM / L&K or equivalent and approved make, including jointing with water supply lines, complete as directed by EIC . (+) 2.00 Each 1000.00 Rupees One Thousand Only 2000.00

46 Supplying and fixing of CP brass angle cock / valves of Plumber / GEM / L&K make for 15 mm dia pipe including jointing with water supply line and all complete operation for fixing including required accessories etc. complete as directed by EIC. (+) 3.00 Each 700.00 Rupees Seven Hundred Only 2100.00

47 Supplying and fixing 580 x 440 mm light coloured glaze porceline Indian water closet (Orissa Pattern) confirming to IS:2556 of make parryware or equivalent with'P' or 'S' trap with or without vent set, including supplying and fixing 10 Ltrs. Capacity valve less syphonic action type low level PVC cistern confirming to IS : 774, with brackets, 40mm dia PVC waste pipe with coupling, 15mm dia high density PVC inlet pipe connection, 15mm dia CP angle cock of parry ware all above of approved make, colour etc complete as approved, specified and directed by the EIC. (-) 1.00 Each 3000.00 Rupees Three Thousand Only 3000.00

48 Supplying and fixing of good quality bevelled edge looking mirror of 5mm thickness of approved manufacturer such as Modi Atul , saint -gobain etc of any size with AC Sheet backing and 1" wooden beading all round edges, all complete as per direction of EIC. (+) 0.90 Sqm 1000.00 Rupees One Thousand Only 900.00

49 (a) Supply & fixing of G.I. water tubing 15 mm dia (Galvanized Iron) TATA/ JINDAL/ ZENITH make of medium grade in required lengths with screwed socket joints, together with all tube, fittings (Such as bends, elbows, tees, short pieces, connectors back-nuts, diminishing pieces, caps, plugs and unions etc.) and fixing complete with clips, wall hooks, wooden plugs at suitable intervals including cost of cutting through walls, floors / roofs etc and their making good, laying in trenches etc. Also for cutting, screwing and waste, and for making forged bends on piping as required, connectors shall be inserted, where required or as directed by EIC. 28.00 RM 180.00 Rupees One Hundred Eighty Only 5040.00

(b ) ---do as above but 25 mm dia. (-) 6.00 RM 225.00 Rupees Two Hundred Twenty Five Only 1350.00

50 Supplying and fixing C.P Liquid soap Dispenser of any approved make/ branded hand push types including all fixing accessories and operations etc. complete as directed & approved by EIC. (-) 1.00 Each 300.00 Rupees Three Hundred Only 300.00

51 Supplying and fixing PVC floor trap 75 mm dia. of approved make such as supreme / Finolex/ Kisan/ Prince (ISI mark)with grating including jointing to waste PVC pipes with cement concrete 1:2:4 etc. complete as directed & approved by EIC. (-) 4.00 Each 200.00 Rupees Two Hundred Only 800.00

52 Supplying and fixing 110mm/ 75mm PVC, SWR single socketed pipe in any length with rubber ring joint fixed to walls, laid in trenches, under floor for soil waste of approved make such as Supreme Kisan, Finolex, Prince or equivalent Conforming to IS: 4985-2000;(Class - 4) complete with all required necessary fittings for fixing etc. complete as directed & approved by EIC for following dia. pipes

(a) 110 mm dia. (-) 3.00 RM 250.00 Rupees Two Hundred Fifty Only 750.00

(b) 75 mm dia. 10.00 RM 200.00 Rupees Two Hundred Only 2000.00

53 Supplying and fixing PVC (SWR) Junction single 'T' equal or unequal with access door for following dia. of Supreme, Kisan, Finolex, Prince (ISI make) etc. complete as directed & approved by EIC.

(a) 110 mm dia. (-) 2.00 Each 200.00 Rupees Two Hundred Only 400.00

(b) 75 mm dia. 4.00 Each 150.00 Rupees One Hundred Fifty Only 600.00

54 Supplying and fixing PVC (SWR) bends of any radius with access door for following dia. of pipes of Supreme, kisan, Finloex, Prince (ISI make) etc complete as directed & approved by EIC.

(a) 110 mm dia. 2.00 Each 200.00 Rupees Two Hundred Only 400.00

(b) 75 mm dia. 4.00 Each 150.00 Rupees One Hundred Fifty Only 600.00

55 Supplying and Fixing PVC(SWR) reducer 110 x 75 mm of Supreme, kisan, Finolex, Prince make etc. complete all as directed & approved by EIC. (+) 1.00 Each 150.00 Rupees One Hundred Fifty Only 150.00

56 Supplying and Fixing PVC(SWR) vent cowls 75 mm dia of Supreme, kisan, Finloex, Prince (ISI make) etc. complete all as directed & approved by EIC. (+) 1.00 Each 125.00 Rupees One Hundred Twenty Five Only 125.00

57 Supplying and fixing PVC water tanks of make Sintex/ Polycon/ Tirupati / Supreme rotational moulded polythelene water storage tanks 1000 Ltr. cylindrical vertical with closed top hoisted and fixed to position, three layer body, including providing and fixing PVC ball cock, tank connection and all required G.I. fittings etc. complete as directed and approved by EIC. (+) 1.00 Each 9000.00 Rupees Nine Thousand Only 9000.00

58 Providing and fixing to chowkhat 30 mm thick, single leaf, factory made flush door shutter conforming to IS- 2202( Part-I)-1983, of G-door, Minar, Swastik, Shatabadi make and ISI marked, solid core construction, with block board core and commercial types veneers face on one sides and other face is covered with decorative face veneer with lipping/frame to match etc. complete , flush door shall be free from twist or wrap in plane etc. including provision of suitable blocks for interlocks, latches or other fittings etc. complete as directed & approved by EIC. (+) 2.50 Sqm 2800.00 Rupees Two Thousand Eight Hundred Only 7000.00

59 Providing and fixing CP Brass health faucet with telephonic arrangement and hook etc. of Plumber / GEM / L&K/ or any other equivalent make complete with required fittings & accessories as per direction of EIC. (+) 1.00 Each 1100.00 Rupees One Thousand One Hundred Only 1100.00

60 Supplying & fixing C.P Bottle trap of Plumber / GEM / L&K or any other equivalent brand etc. complete and approved by EIC. 3.00 Each 1100.00 Rupees One Thousand One Hundred Only 3300.00

61 Supplying erection & fixing of sliding door of aluminium powder coated of vertical, top middle & bottom rails of section 100 x 44 x 2mm and stiles of Sec. 83 x 44 x 2mm including supplying & fixing of top panel with 5mm with figured glass, pinhead type & bottom panel with 12mm botttom pre-laminated board including cost of handle, lock, glazing clip, rubber beading, G.rails and sliding roller for sliding door Complete as directed & approved by EIC. 2.50 Sqm 4000.00 Rupees Four Thousand Only 10000.00

62 Supplying, fabricating and fixing Stair (framed) including stringers, treads, landing, railings, balusters, hand rails etc. including cleats, brakets, etc. including one coat of red oxide primer providing metal putty and sand papering for making the surface smooth and two coat of first quality synthetic enamel paints, complete all as directed & approved by EIC. 4500.00 Kg 100.00 Rupees One Hundred Only 450000.00

63 Providing, centring & shuttering for the sides and soffits of suspended slabs, lintels, beams, floor slabs, landing and similar work of any description, in required shape and size, with true line & plumb etc. with plywood, MS plates shuttering including oiling of the top surfaces of shuttering , all supports with MS or wooden braces, struts, balli, etc, including working scaffoldings, ladders, gangways as required, including removal of formwork & centring after the stripping period as described in MES-SSR- part-I & IS 456 2000 , etc complete as directed and approved by EIC. 550.00 Sqm 250.00 Rupees Two Hundred Fifty Only 137500.00

Amount in Rs. 4699675.00

Amount in words:- Fourty Six Lakh Ninty Nine Thousand Six Hundred Seventy Five Only.

Name Of Work :“Provisioning of Temporary Yoga shed in the Subhas Chandra park and renovation works in Gym at HAL Township Kanpur."

CA. No. MW/CIV/990/1/25-26

TECHNICAL BID Appendix ‘A’

PRE-QUALIFICATION DETAILS OF APPLICANTS

Note:1. Vendors may upload a separate sheet in prescribed format along with Annexures name and No., if space provided below is not sufficient.

2.Vendors are requested to write in the yellow shaded portion only.

Section 1: Applicant’s Particulars

Name of the Individual / Firm / Company:

Constitutional or Legal Status of the firm

Registration Number From ROC(If any): Registering Authority Date of Registration

Registered Address:

Contact Person Name & Designation:

Address for correspondence(If different from Regd.Address):

Tel. No. Fax No.

Mobile No. Email Address:

PAN/GIR No. (Copy to be attached) GSTIN (Copy to be attached)

(This declaration should be completed by a proprietor, partner, director or other senior manager who has the authority to do so.)

‘I accept the HAL terms & conditions for this contract and declare that the particulars shown herein are true & correct in every detail.’

Details of persons holding the power of Attorney [If different from above]

(Upload, attested copy of Notarized Power of Attorney)

Name Tel No.: Mob:

Position Fax No.:

Section 2: Applicant’s Profile

2.1 Detail of registration of the firm if available with different following organizations (Attach necessary certificates from the registering authorities):

Company Registration Number Dated Validity Value of Contract for which Registered Class/Type of Registration

HAL or its Division

Others(if any) (Specify).

2.2 Upload Company’s Memorandum of Association and Articles of Association / to be enclosed. Board resolution paper may be enclosed along with the memorandum of association (in case of Pvt.Ltd./Ltd.Co.) / Partnership Deed (in case of Partnership firm). (Write Enclosed / Not Enclosed) .

2.3 Information on litigation history, in which the Bidder is involved (Write Yes/No in Col.5).

Other party(ies) (Dispute involved with) Name of Employer Cause of dispute Amount involved. Remarks showing present status. (Write Yes/No )

Details Attached (if Yes) [Write attached / Not attached].

2.4 In the last 5 years, has your firm, or any firm with which any of your company’s owners, officers, partners were associated, been debarred, disqualified, removed, blacklisted or otherwise prevented from bidding or completing any contract (Write Yes / No).

If yes, state the project and the basis for the action.

Section 3 – Prequalification criteria

3.1 Solvency for a minimum value of Rs. 12.86 Lakh issued within a period of 12 months from the final date of submission of tender. i.e on or after 10.04.2025. In solvency certificate, solvent / solvency word must be mentioned failing which tender are liable to be rejected.

Name of Bank & Branch Bank’s Reference and Date Value Rs. In Lakhs

3.2 Annual turnover in the past 3 years ending 31-03-2025.

Note:- The annual turnover should be supported with audited financial statements and profit & loss statement of the concerned year with UDIN no. The average annual turnover for the last three years (starting from 2022-23 onwards) as above should not be less than 30 (Thirty) % (Rs. 9.64 Lakh) of the estimated cost as indicated in the tender document. It is mandatory to furnish all the three year annual turnovers failing which tender are liable to be rejected.

Financial Year (Assessment year shall not be considered) Annual Turnover (Rs. In Lakh) Average Annual Turnover for last three Years ( Rs. In Lakh) 16.07

3.3 Experience details

Experience of having successfully completed similar works during last seven (07) years starting (From 31.05.2019 to 01.04.2026) should either of the following. (Work completed as a whole only shall be considered as experience; Ongoing work / partially Completed works / Work-orders shall not be considered as experience certificate). Scanned copy of experience certificate must be uploaded. (a) ONE similar completed work costing not less than 80% (Rs. 25.71 Lakh) of the amount put to tender.

S. No. Name of the Work Date Of Completion Completed Cost Completion Certificate [Mandatory] Write Enclosed/Not Enclosed Name, address & Phone no. of the client

(b) TWO similar completed works costing not less than 50% (Rs.16.07 Lakh) of the amount put to tender

S. No. Name of the Work Date Of Completion Completed Cost Completion Certificate [Mandatory] Write Enclosed/Not Enclosed Name, address & Phone no. of the client

(c) THREE similar completed works costing not less than 40% (Rs. 12.86 Lakh) of the amount put to tender.

S. No. Name of the Work Date Of Completion Completed Cost Completion Certificate [Mandatory] Write Enclosed/ Not Enclosed Name, address & Phone no. of the client

Note:- Completion certificate issued by the client should contain Completed value of the work, date of completion, duly supported by Work-order copy & agreement copy. TDS certificate for full completion value is to be enclosed in case the client is a private firm. Tender offer shall be liable for REJECTION if the tenderer has not furnished the Completion certificate.

Similar Works - Experience in carrying out All types of Civil works at shall be considered as similar works.

Section 4 - Declaration

4.1 I/We declare and confirm that -

a. All information and attachments submitted in this application are true and correct.

b. I/We are aware that any false information provided herein will result in the rejection of my application and suspension of any registrations granted.

c. I/We shall not make refund claims of expenditure incurred in processing this application.

4.2 I/We enclose herewith a pay order / banker’s draft number: drawn on Bank:

Branch & address Name

Date: Designation: