Proposed Development space creation for transformer external protection wall internal external logo name board and directories to complete works for JNPT Administration building

Amount

Excavation For Foundation in earth, soil of all types, sand , gravel and soft & Hard murum, including removing the excavated material up to a distance of 50m beyong the building area and stacking and spreading as directed, dewatering, preparing the bed for foundation and necessary backfilling with available earth / murum, ramming , watering including shoring and strutting etc. complete By Mechanical Means

Excavation for Foundation in Hard Rock by chiselling, wedging line drilling, etc. including trimming and levelling the bed, removing the excavated material and stacking it in measurable heaps within a distance of 50m from the building area or site including dewatering and backfilling with available earth soil / murum watering, ramming etc. complete By Mechanical Means

Providing preconstructional antitermite treatment as per IS 6313 (Part - II ) by treating the backfill in immediate contact with foundation at the rate of 5 litres of emulsion concentrate of 1.0 percent of chlorophyrifos per square meter of surface area.

Providing dry /trap / granite quartzite / gneiss rubble stone soling 15cm to 20cm thick including hand packing , filling voids with Crushed sand / grit ramming watering, compaction etc. complete

Providing and laying cast in situ / Ready mix cement concrete of M-15 Grade trap / granite / quartzite / gneiss metal for foundation and bedding including bailing out water, steel centering, formwork, laying / pumping, compacting roughening them if special finish is to be provided, finishing if required and curing complete with fully automatic micro processor based PLC with SCADA enabled reversible Drum type mixer / Concrete batch mix plant (Pan Mixer) etc. complete with fine aggregate (Crushed sand VSI Grade)

Providing and laying cast in situ / Ready Mix Cement Concrete of M-25 Grade trap / granite / quartzite / gneiss metal for R.C.C. work in foundation like raft, strip foundations, grillage and footings of RCC Columns, Foundation of Paradi or Wall and steel stanchions etc as per detailed design and drawing including bailing out water, steel centering, formwork, cover blocks laying / pumping, compaction and curing rougheneing the surface if special finish is to be provided (Excluding Reinforcement and structural steel) etc. complete with fully automatic micro processor based PLC with SCADA enabled reversible Drum type mixer / Concrete batch mix plant (Pan Mixer) etc. complete with fine aggregate (Crushed sand VSI Grade)

Providing and laying cast in situ / Ready Mix Cement Concrete of M-25 Grade trap / granite / quartzite / gneiss metal for R.C.C. Paradi / Retaining Wall of required thickness including steel centering, formwork, cover blocks, laying / pumping , compacting and roughening them if special finish is to be provided and curing complete (Excluding Reinforcement and structural steel) etc. complete with fully automatic micro processor based PLC with SCADA enabled reversible Drum type mixer / Concrete batch mix plant (Pan Mixer) etc. complete with fine aggregate (Crushed sand VSI Grade)

Providing and fixing 25 mm diameter steel anchor dowel in hard rock including drilling hole of 32 mm diameter upto 0.75 mtrs depth, placing the dowel in position and effectively grouting the hole with CM 1:1 proportion etc. complete.

Providing and fixing in position TMT - FE 500 bar reinforcement of various diameters for RCC Foundations, Walls, Pile caps, footings, beams, slabs, raft etc. as per detailed design and drawigs and schedules including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required .

Providing and fixing in position HCRM / CRS (Corrosion Resistant Steel ) bar reinforcement of various diameters for RCC Pile Caps, footings, foundations, slabs, beams, columns, canopies, staircase, newels, chajjas, lintels, paradies / walls, copings, fins, arches etc. as per detailed design and drawings and schedules including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete.

Supplying, drilling/ Cleaning Hole and injecting Hilti make ETA Approved HY-200-R Chemical. Applycation to be designed seperately for Rebars as Simply Supported , Moment or Splice Connection as per EC-2/TR-023 or relevant tested and accepted rebar guidelines.The chemical should have ETA approval for seismic rebar as a minimum qualifying criterion. Drilling hole with double flute type drill bits or hollow drill bits to the required depth by rotary hammer drill, cleaning with brush and jet of clean air, filling resin and hardner using serrated nozzle to elimanate mixing error with standard HDE A22 battery dispenser along with piston plug. The installation and the setting instructions should be strictely followed as per the manufacturers recommendations. The adequate diameter and embedment for rebars to be decided as per PROFIS Rebar Software and the report to be submittted to the Projct Manager / Design Engineer for approval. scanning before drilling to be done to avoid hitting existing rebars HY20 - 8 mm to 12mm Dia 240mm depth.

Supplying, drilling/ Cleaning Hole and injecting Hilti make ETA Approved HY-200-R Chemical. Applycation to be designed seperately for Rebars as Simply Supported , Moment or Splice Connection as per EC-2/TR-023 or relevant tested and accepted rebar guidelines.The chemical should have ETA approval for seismic rebar as a minimum qualifying criterion. Drilling hole with double flute type drill bits or hollow drill bits to the required depth by rotary hammer drill, cleaning with brush and jet of clean air, filling resin and hardner using serrated nozzle to elimanate mixing error with standard HDE A22 battery dispenser along with piston plug. The installation and the setting instructions should be strictely followed as per the manufacturers recommendations. The adequate diameter and embedment for rebars to be decided as per PROFIS Rebar Software and the report to be submittted to the Projct Manager / Design Engineer for approval. scanning before drilling to be done to avoid hitting existing rebars HY20 - uo to 16 to 25mm Dia 500mm depth.

Providing and applying waterproofing treatment using acrylic polymer modified cement based water proofing coating with fibre glass mesh mixing at the rate of powder to liquid (2:1) by weight covering 9 to 10 Square Meter / Kilogram with two coat using approved chemicals for masonry and concrete surfaces by brush covering 7 years guarantee on Stamp Paper etc. complete.

Waterproofing Treatment to existing Terrace by using Polymeric cementatious membarne of approved make and approved by Engineer-In-Charge by replacing the existing waterproofing treatment. Break open the existing IPS and brick bat coba of the terrace slab to expose the bare slab. (If there are cracks on the bare slab open the crack in V Groove and fill it with P.M.M. and if there are a lots of honeycombs and identified bad patches of concrete the same should be grouted by grouting procedures). Clean the entire surface throughly and over this prepared surface, apply three coats of polymeric water proofing coating having a breathable non toxic acrylic polymer liquid of approved make and approved by Engineer-In-Charge, over this waterproofing treatment, provide andd lay brick bat coba of average 112 mm thickness.

Providing cement based water proofing treatment to terraces (Indian Water proofing or alike ) with brick bats laid in required slope to drain the water for any span after cleaning the base surface. Applying a coat of cement slurry admixed with approved water proofing compound and laying the brick bats on bottom layer in C.M. 1:5 admixed with approved water profing compound filling up to half depth of brick bats, curing this layer for 3 days, applying cement slurry over this layer joints of brick bats with C.M. 1:3 admixed with approved water proofing compound and finally top fininshing with average 20mm thick layer of same mortar added with jute fibre at 1 Kg / bag including finishing the surface smooth with cement slurry admixed with approved water proofing compound. Making finished surface with false square of 300mm x 300mm making the junctions at the parapet rounded and tapered top for required height, with drip mould at the junction of plaster and parapet and curing.

Providing second class Burnt Brick Masonry with conventional /I.S. type bricks in cement mortar 1:6 in foundations and plinth of inner walls / in plinth external walls including bailing out water manually, striking joints on unexposed faces, racking out joints on exposed faces and watering etc. complete.

Providing Autoclaved Aerated Concrete Block Masonry of Ecolite or equivalent make confirming to IS 2185 (Part -3) -1984 in extra fine jointing mortar of fixoblock of Ultra Tech or equivalent in superstructure including striking joints, racking out joints and scaffolding etc. complete (The Test shall be carried out confirming to IS : 6441(Part-1) - 1972 )

Providing internal cement plaster 20mm thick in a single coats in cment mortar 1:4 without neeru finish to concrete or brick surface, in all position inlcuding scaffolding and curing etc. complete.

Providing and applying plastic emulsion paint of approved quality, colour and shade to old surface in three coats including scaffolding, preparing the surface.(excluding the primer coat ) etc. complete.

Providing and Applying 30mm thick self curing Ceremic Polymer Microconcrete of approved make having compressive strength abive M3, non shrink, impermeable, filling mortar to load carrying RCC Member in two layers on cleaned concrete surface, including honey comb area (using manual / mechanical means). Mixing mortar of Nicosil C80 and fresh 53 grade cement with required water cement ratio for desired consistency and applying and finishing by manual trawelling, curing after initial setting time etc. as per manufacturers specification etc. complete as per specification and as directed by the Engineer-in-Charge.

Providing and Applying Kelox R 101 (Resin ) + Kelox H 404 (Hardner ) water misible epoxy of approved make for bonding old concrete to new mortar after mixing slowely in predefined ratio and applying by brush on the surface, when it is tacky then apply the mortar complete as per specification and as directed by the Engineer-in-Charge.

Providing and fixing in fixing in position (as per 1868 / 1982) Aluminium sliding window of three tracks with rectangular pipe 95 x 38.10 x 0.90 mm at weight 0.637 Kilogram/Running metre. With window frame bottom track section 92mmx31.85mmx1.3mm at weight .933 Kilogram/Running meter. The Shutter should be of bearing bottom 40 x 18 x 1.25 mm at weight 0.417 Kilogram/Running metre. Inter locking section 40 x 18 x 1.10 mm at weight 0.469 Kilogram/Running metre. and handle and top section 40 x 18 x 1.25 mm at weight 0.417 Kilogram/Running meter As per detailed drawings and as directed by Engineerincharge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mm thick plain glass and aluminium mosquito net shutter with stainless steel jali with all required screws and nuts etc, complete. With powder coating without box

Providing and Fixing Aluminium Louvered Windows : Providing and fixing in position aluminium louvered windows/ ventilators (IS std.) of various sizes with powder coating as per detailed drawings and specifications including aluminium frames 80 x 38 mm box type 5 mm thick sheet glass louvers, clips / rubber plain P.V.C.. gaskets of approved quality etc. complete.. (Sample to be got approved from Ex. Engineer before use) Rate includes removing existing shutters stacking the same at JNPT Store yard as directed by engineer incharge

Providing and fixing mild steel grill work for windows, ventilators etc. 20 Kg / Sq.M as per drawing including fixtures, necessary welding and painting with one coat of anticorrosive paint and two coats of oil painting complete.

Providing and fixing rolling shutter fabricated from steel laths of minimum thickness 0.9mm with lock plate of 3.15mm thickness reinforced with 35x35x5mm angle sections fitted with sliding bolts and handles for both sides, deep M.S. Channels section of depth and thickness not less than 65mm and 3.15mm respectively with hold fast arrangements, M.S. Bracket Plate 300 x 300 x 3.15mm minimum size and shape with square bar, suspension shaft of minimum 32mm diameter, hood cover of M.S. sheet not less than 0.9mm thickness and of any size at top and safety devices including mechanical gear operation arrangement consisting of worm gear wheels and worms of high grade cast iron or mild steel and one coat of red lead primer etc. complete (IS 62481979 ) (With Mechanical gear)

Providing and Applying polyurethane sealant for the Expansion Joint of size 50x25 mm Cleaning the groove , preparing the groove ration using Baker Rod Masking the joint form both the side Applying the primer After desired interval filling the grove Gun Grade Polyurethane sealant, work Will be Done as per Direction by Engineer In-Charge.

Road Marking with Hot Applied thermoplastic Compound with Reflectorising Glass Beads on Bituminious Surface - Providing and laying of hot applied thermoplastic compound 2.5mm thick including reflectorising glass beads @ 250 gms per square metre area, thickness of 2.5mm is exclusive of syrface applied glass beads as per IRC:35. The finished surface to be level, uniform and free from streaks and holes complete.

P&F ACP Cladding : Designing, providing, fabricating and installing Aluminium Composite panels cladding system on exterior façade (inclusive of exterior 3-6mm panels of 600 x 1200 or approved size) with back structure framing arrangement, as per approved design (based on concept architectural elevation drawings), hot dip galvanized / non ferrous metal anchor fasteners, jointing and sealing with approved compatible silicon sealant (Dow Corning or equivalent approved). Work to include preparing and finishing of junctions with concrete, masonry, aluminum including us of flashing if any as approved by the Engineer in charge etc. all complete. Rate includes removing existing cladding material stacking the same at JNPT Store yard as directed by engineer in charge. Make Alstrong or equivalent

P&F PVC Pipe 110mm Dia : roviding and fixing 110 mm dia stabiliser pipe/ P.V.C. soil vent/waste pipe and with necessary fixtures and fitting such as bends, tees, single junctions, slotted vent, clamps etc. com-plete

Providing and laying cement concrete pipe of IS458:2003 NP-3 class of 600mm diameter in proper line, level and slope etc. complete.

Providing and fixing mild steel grill railing weighing 20Kg/ Sqm with PVC Handrail cover including fabricating, fixtures, drilling holes in concrete / other surface, erecting the grill work, necessary welding, fixing by nuts and bolts, fixing PVC handrail cover, with one coat anticorosive paint and two coats oil painting with approved colour and shade, remaking the damaged surface, cleaning etc. complete as directed by the Engineer-in-charge.

P&F Flooring 600 x 600 : Providing and fixing MATT FINISH ANTISKID tiles of minimum size 600 x 600 mm of about 10mm thick having water absorption less than 0.055 of approved make, shade and pattern for floor & dado in required position fixed on plaster of cement mortar 1:4 neat cement paste. including filing joints with neat white cement slurry curing cleaning etc. complete

P&F Vitrified Tiles DADO 600 x 300 : Providing and fixing decorative Italian marble effect tiles of minimum size 600 x 300 mm of about 10 mm thick having water absorption less than 0.055 of approved make, shade and pattern for dado in required position fixed on plaster of cement mortar 1:4 neat cement paste. including filing joints with neat white cement slurry curing cleaning etc. complete

Providing and fixing SCUBE Restroom cubicles SPLENDOR of following standard which include 750 mm door size (width), made of heat, bacteria water, chemical impact, anti bacterial resistant. 18 mm solid/wood grain Laminate. Finish of the compact laminate should be suede. Which include doors, pilaster and intermediate panel finished with approved textures/shades as per the details drawings & as per IS 2026 (Indian Standard) and as per the fire retardant BS-476/97 Standard. This also details providing and fixing in positions necessary hardware made out of SIZE OF DOOR IS 750MM X 2100MM,SS 304 GRAVITY HINGES,DOOR KNOB CUM HANDLE ALLUMINIUM SS FINISH/ANODIZED FINISH AND SS 304 LOCK CUM HANDLE, D POST CHANNEL FOR FIXING DOORS.( ALLUMINIUM SS FINISH), SS 316/304 SCREW

Providing & Fixing of URINAL PARTITION 900*450 { 18mm HPL WITH SS 304, 6 BRACKETS} Use Accessories-Merino Make SS 304 grade Right angle Brackets 304 G ,PVC Wall Plugs as per approve Design and drawing.- Basic Rate - 6500/-

Providing and fixing Orissa type white glazed earthenware water closet pan of size260mmx440mmx580mm with approved make Slim wall hung cistern with installation kit including S or P trap with cast iron soil and vent pipe up to outside face of the wall 1:2:4 brick bat lime concrete bedding without flushing tank and its accessories etc.complete.

Signages

Entrance Gate Branding 3D Signage -Prototyping supply installation & commissioning letters made of 18 gauge thick S.S.316material laser cut out with 25mm x 18 gauge thick side patti brazing for box type 3D Letters with backside S.S.Scrue brazing for fitting arrangment .all letter polish & white colour PU coated as per your requirment.All inculisive of Transpot Labour mechanical cutting Drillding , Making holes etc complete

Prototyping supply installation & commissioning logo & letters made of 18 gauge thick S.S.316 material laser cut out with 25mm x 18 gauge thick side patti brazing for box type 3D Letters with backside S.S.Scrue brazing for fitting arrangment .& Logo fitted on 30"Ø S.S. Base plate with PU coating Colour as per artwork.All inculisive of Transpot Labour mechanical cutting Drillding , Making holes etc completed

Main Logo Dia - 30 "

Size 12'' X 12 "

Size 36'' X 36 "

Floor Directory Board rectangular in shape,Shall be made of half round extruded black anodised aluminium frame ( wall thick 1.7mm).The Vertical & horizontal arms of the frame shall be connected byS.S.Scrue .Individual Logo,Floor,Name Plates shall be extruded Black anodised aluminium plates having lengthwise semicircular grooves.These plates shall be held together by passing dumbbel sleeves through these grooves.Approved text/Graphics shall be computer cut and pasted on these plates and shall be protected by 2mm thick clear acrylic plates.The complete plate assembly shall be inserted in the slot provided in the frame.The floor Directory Board shall have flush wall mounting arrangments at the back side of the boards.

Brass -Prototyping supply installation & commissioning single side nameplate Signages shall be made of 25mm thick pi shape extruded 6063 -T6 aluminium profile of 2mm wall thickness.two 3 mm internal ribs shall be provided for corner locking the profile shall Gold/ Sliver/ Black anodised 15micron dept.The display shall be 3mm thick aluminium sheet with PU Coated in black colour with aproved text in 4mm Brass cutout laser cut letter with gold plating & lacqur coating fittted on aluminium plate.The signage shall be provided wih trarded S.S.Stud welded at the backside of the wall mounting Rate Inclusive of Base plate & Hindi English Letters as Design & Directed by Architect

Advnace Modular Cabin Name plate Shall be made of hollow 19 ±1.0mm thick black anodised extruded aluminium frame & wall thickness of 1.7mm.The frame joining side cap shall be of moulded nylon -6 material . name plates (3" ,4" wide) shall be held together by a 9mm dumbell sleeve inserted in the circular grooves of the name plate.This assembly of name plates shall be inserted in the groove of the frame.The approved text will be computer cut on Gold coloured vinyl and pasted on the name plates as per the approved artwork.2mm thick clear acrylic plates shall be inserted in the grooves of name plates to protect the matter from dust & Vandalism.

The Successor's Board should be flush wall mounted type, made of Bronze colour anodised hollow Aluminium Extruded Profiles having 35±1.0 mm thickness & 1.7 mm wall thickness with R30.The overall height of the inverted "U" shaped Aluminium one piece frame without joint should be 953±1.0 mm to 1790±1.0 mm, width of 610±1.0 mm to 1220±1.0 mm max., The outer radius of the top semi circle will be R305±1.0 mm to R610±1.0 mm. The corner brackets for joining the bottom horizontal arm to the frame should be made of unbreakable Nylon 66. These brackets should have two 3mm thick internal ribs to impart additional strength. Two sturdy 1.2mm thick powder coated brackets with key hole suitable for Ø 5mm are provided at the rear for flush wall mounting.The logo of the organisation should be latex eco friendly printed on vinyl stickers and the text matter computerized cut out vinyl of Ivory colour and pasted on the semi circular Bronze colour anodised Aluminium sheet 2 mm thick and to be protected by a 2mm thick clear acrylic sheet.Individual name plates should be 1.3 mm thick and 9.35 mm collar, having length wise profile suitable for interchanging size 38.1mm interlocking with “I” sleeve extrusion of 9mm. The width of name plate should be maintained to accommodate vinyl name stickers having letter height suitable to be clearly legible from a distance of 10 mtrs.All the names / characters on the name plate to be protected by a 2mm thick clear acrylic strip.All anodised components should have coating thickness not less than 15µm.The complete assembly should be such that any intermediate name plate can be easily replaced / interchanged without completely dismantling the board.

Elipitical Glowsign Signage - ,Techincal & userfriendly design as per individual locations ,manufacture and supply of double sided floor mounted self standing LED illuminated Elliptical Glow Sign Boards consisting display of Aminities directions. The structural members shall be made of M.S. squaire tube welded structure with coverd top bottam & two side 2side 3mm ACP Sheet . The display sheet shall be of unbreakable 040 translucent Polycarbonate sheet of 2 mm thickness. Approved text & graphics in approved colors shall be printed / router cut on 70 µm thick monomeric calendered vinyl & shall be firmly pasted on the display

Providing fixing of LED signage to indicate the Exit route with running symbol/staircase steps including mounting accessories on side wall or handing from the ceiling.Scope included to providing power supply points with 15 concealed wiring. Model: PEL LEDE/M (SM)

Providing & Fixing 10 mm line Sign one side aluminium profile frame with front side 3mm Silver colur ACP sheet with pasted with double side tape text matter in autoglow & direction printed on autoglow film & pasted on ACP Sheet with mat lamination. .provided key bracket with scerw for fitting frame.

Fire Exit - Made of Aluminium profile frame with insert both side 3mm aluminium composite panel sheet & pasted autoglow vinyl film with text matter & direction printed on clear film & pasted bothside with Mat lamination provided Roof wire & S.S.Bush for Installation.

Providing 3d Model of JNPT port at the scale of 1:50 ofApprox size 4000mmx4000mm as Directed By Architect _ Basic Rate 800000/-

Supply, Installation and Laying of 3.5 core 300 sq.mm Alu cable

Supply Installation & Laying of 1 Core 95 Sqmm Alu Cable

Supply, Installation and Laying of 3.5 core 185 sq.mm Alu cable

Supply, Installation ,End Termination of 3.5 core 300 sq.mm Alu cable

Supply, Installation ,End Termination of 3.5 core 185 sq.mm Alu cable

Supply, Installation of 200x50 cable tray with cover for -HVAC Panel

Supply, Installation of 300x50 cable tray with cover for -HVAC Panel

SITC of fiber splicing for camera work

Providing & erecting 4 m high (clear height) galvanized OCTAGONAL pole with foundation boltshaving bottom of 130 mm A/F, top 70 mm A/F onprovided foundation as per specification

Knchan Associates