GE/U(N)-28/2024-25 REPAIR/REPLACEMENT OF CERTAIN B/R AND E/M ITEMS AT SUB AREA AND ADJOINING AREA UNDER AGE BR-I OF GE (N) UDHAMPUR

Amount

Demolition of un-reinforced cement concrete in roofs, floors ( other than ground floors), beams, staircase, landing, chhajjas and similar suspended work of and pavings not exceeding 15 cm thickness(below or above ground level) complete all as specified and as directed.

M&L for 25 mm thick plain cement concrete1:2:4 type B1(using 20 mm graded stone aggregate) as in sub base of flooring and roof treatment all as specified and as directed.

Providing and laying water proofing treatment to sunken portion of WCs, bathrooms, roof etc by applying two coat of slurry of cement @ 0.488kg/Sqm mixed with acrylic based polymer modified cementations composite compound @ 0.253kg/sqm this layer allowed to air cure for 4 hrs then applying slurry of cement @ 0.242 kg/sqm mixed with acrylic based polymer modified cementations composite compound @0.126kg/sqm and allowed to air cure for 4 hrs and joints seal with sealing compound as approved by GE. Note: (i) Before laying of lime concrete joints of trap/WC/Soil pipes shall be properly sealed with sealing compound of Roofex /Forre/FOSROC and provn of P or S trap & Nahani /Floor traps with long arm and also provn of spout of 40 mm dia complete all as specified and as directed.

Rendering 15mm thick on fair faces of brick work or concrete surfaces in Cement mortar as in CM 1:3 finishing even & smooth w/o using extra cement, complete all as specified and as directed complete all as specified and as directed.

Lean concrete using 40mm graded stone aggregate as in 1:5:10 as in filling sunken portion treatment, complete all as specified and as directed.

M&L in repair 20 mm thick cement plaster on fair face of concrete surface including repair of doubing roof/chhajja/facia surfaces in CM 1:3 finished even land smooth without using extra cement over complete all as specified and directed. (Water proofing compound shall be measured and paid separately )

Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and recast concrete articles all as specified.

M&L Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM(1:6) with old size bricks complete all as specified and as directed.

M&L Brickwork s except bricks, straight or curved on plan exc 6m mean radius built in CM(1:6) with old size bricks complete all as specified and as directed.

M&L half Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM(1:6) with old size bricks complete all as specified and as directed.

Taking up/down steel tubing and connections including cleaning for re-fixing or removal to store 15mm bore pipes complete all as specified and as directed.

Taking up/down steel tubing and connections including cleaning for re-fixing or removal to store 25 mm bore pipes complete all as specified and as directed.

Taking up/down steel tubing and connections including cleaning for re-fixing or removal to store 40 mm bore pipes complete all as specified and as directed.

S&F 15 mm bore steel water Tubing 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

,-ditto- as above item 14 but except pipe complete all as specified and as directed.

S&F 25 mm bore steel water Tubing 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

,-ditto- as above item 16 but except pipe complete all as specified and as directed.

S&F 40 mm bore steel water Tubing 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

-ditto- as above item 18 but except pipe complete all as specified and as directed.

Disconnection of existing tanks, setting side for repairing, cleaning etc and hoisting after cleaning and removing all scale and dirt etc from tanks and from mouth of circulating pipe etc of capacity upto and including 500 ltrs and endorsed the ward ' CLEANED ON WITH DATE' with white paint including replacement of broken/unserviceable fitting such as Elbow, Tea, socket, nipple of any size etc, complete all as specified and directed by the Engr-in-Charge.

Description all as per Srl item No.01 here in before but of capacity exc 500 ltrs and upto & including 1000 ltrs and endorsed the word' ' CLEANED ON WITH DATE' with white paint including replacement of broken/unserviceable fitting such as Elbow, Tea, socket, nipple of any size etc, complete all as specified and directed by the Engr-in-Charge.

Description all as per Srl item No.01 here in before but of capacity exc 1000 ltrs and upto & including 2000 ltrs and endorsed the word' ' CLEANED ON WITH DATE' with white paint including replacement of broken/unserviceable fitting such as Elbow, Tea , socket, nipple of any size etc, complete all as specified and directed by the Engr-in-Charge.

Dismantling water tanks of exceeding 250 & not exceeding 500 ltrs and removing to store, complete all as specified and as directed.

Dismantling water tanks of exceeding 500 & not exceeding 1000 ltrs and removing to store, complete all as specified and as directed.

Dismantling water tanks of exceeding 1000 & not exceeding 2000 ltrs and removing to store, complete all as specified and as directed.

M&L for Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of 500 ltrs capacity (Triple layer) white in colour including water tank cover (internally/interlocking arrangement for water tank cover), hoisted and fixed in position including tank nipple inlet & outlet and connecting up pipes complete all as specified and directed.(fixed in repair) complete all as specified and as directed.

M&L for 1000 ltrs capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) three layer white in colour (inside outside) hoisted and fixed in position incl inlet, outlet and overflow connection nipple of suitable size complete all as specified and as directed.

M&L for Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) of 2000 ltrs capacity (Triple layer) white in colour including water tank cover (internally/interlocking arrangement for water tank cover), hoisted and fixed in position including tank nipple inlet & outlet and connecting up pipes complete all as specified and directed.

S&F 25 mm Gun metal, global or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed in repair complete all as specified and as directed.

S&F 20 mm Gun metal, global or gate valves, with iron wheel head, screwed both ends for iron pipe complete all as specified and as directed.

S&F ball brass valve 25 mm dia high pressure with polythene float and fly nut complete all as specified and directed.

S&F in repairs Ball brass valve 20mm dia high pressure with polythene float and fly nut complete all as specified and directed.

S&F 15 mm Stop valves, brass, fancy type with flange, chromium plated with long shank and cup (concealed type), screwed down high pressure, with capstan head handle, screwed both ends for iron pipe or for unions and fixed.

S&F Stop valve 15mm bore with long shank & cup (concealed type) of PTMT any colour screwed for iron pipe & fixed. (min. weight 15mm-110gms) complete all as specified and as directed.

S&F in repair Stop valve 15mm bore with long shank & cup (concealed type) of PTMT any colour screwed for iron pipe & fixed. (min. weight 15mm-110gms) complete all as specified and as directed.

S&F Angle valve, brass, chromium plated, fancy type, with capstan head handle screwed down high pressure, including CP brass wall flanges; screwed for 15mm bore pipe connection fixed in repairs complete all as specified and directed.

S&F in repair Angle stop valve 15mm bore of PTMT any colour screwed for iron pipe & fixed. (min. weight 15mm-90gms) complete all as specified and as directed.

S&F in repairs Soap dish, Vitreous SS, approximate size 160x160x90mm complete all as specified and as directed.

S&F in repair Salt-glazed stoneware gully traps, square or round mouthed, type 'P' 150x150 mm incl CI cover complete all as specified.

S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and as directed.

S&F in repair 100 mm Cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and as directed.

M&L PVC (SWR) floor trap plain with grating incl. jointing with solvent cement (75 mm bore) complete all as specified and as directed.

S&F PVC nahani trap with grating to 75mm bore including jointing to waste pipe fixed in cement complete all as specified and as directed.

S&F in repair of 10 ltrs PVC valve less, symphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and as directed.

S&F Vitreous china wash down water closet (pedestal pattern) white complete, including connection to drain pipe and to flushing pipe anti symphonage pipe etc, fixed in repair, complete all as specified and as directed.

S&F Plastic water closet seat cover, closet pattern with flat bottom and cover and incl mild steel chromium plated or aluminum hinges device complete all as specified and as directed.

S&F in repair vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests complete incl trap set in and provision of lime concrete filling in sunken portion complete all as specified and directed.

S&F in repair water closet Vitreous China, semi-pedestal pattern (Anglo-Indian Type) white complete, including connection to drain pipe and to flushing pipe anti symphonage pipe etc, fixed in repair, complete all as specified and as directed.

S&F in repairs Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe & waste pipe) complete all as specified and as directed.

S&F Push tap 15mm bore any colour of PTMT screwed for iron pipe suitable for urinals. (min. weight 15mm-50gms) complete all as specified and as directed.

S&F Vitreous China wash basin, white, flat back, size 580x450mm excluding taps, waste chain & plug & porcelain stopper but including brackets complete all as specified and as directed.

S&F flush pipe with rubber washer PVC 32 mm dia for low level cistern pipes, complete all as specified and as directed

S&F for waste pipe of dia 40mm for WHB/Sink, complete all as specified and as directed.

S&F in repairs 32mm bore dia of CP brass waste coupling suitable for WHB, complete all as specified and as directed.

S&F sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers & wastes; including bedding in CM on to dwarf wall or including fixing cantilever brackets & connecting union to pipe, overall size 495mm x 420mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and as directed.

S&F sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers & wastes; including bedding in CM on to dwarf wall or including fixing cantilever brackets & connecting union to pipe, overall size 915mm x 460mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and as directed.

S&F in repairs Health faucet, brass, chromium plated, with 1250 mm long, 15 mm dia chrome finish flexible pipe with wall hook, fixed in repair complete all as specified and directed.

S&F in repair Jet spray, brass, chromium plated, heavy duty, including flexible pipe suitable for 15mm bore water connection; for EWC fixed complete all as specified and as directed.

S&F in repair Bip tap 15mm bore standard of PTMT any colour screwed for iron pipe & fixed (min. weight 15mm - 90gms) complete all as specified and as directed.

S&F in repair Bip tap fancy type 15mm bore standard of PTMT any colour screwed for iron pipe & fixed (min. weight 15mm-105 gms) complete all as specified and as directed.

S&F in repair Bip tap with long body 15mm bore standard of PTMT any colour screwed for iron pipe & fixed (min. weight 15mm-120 gms) complete all as specified and as directed.

S&F in repair Pillar taps15mm bore of PTMT any colour screwed for iron pipe & fixed. (min. weight 15mm-110gms) complete all as specified and as directed.

S&F Pillar taps fancy type15mm bore of PTMT any colour screwed for iron pipe & fixed. (min. weight 15mm-120gms) complete all as specified and as directed.

S&F Towel rail 450mm long of PTMT fixed with & including CP brass screws & wooden/plastic cleats (min. weight 170gms) complete all as specified and as directed.

S&F Bib taps, brass, chromium plated, fancy type, long nose, with capstan head handle screwed down high pressure, including CP brass wall flanges; screwed for 15mm bore pipe connection fixed in repairs complete all as specified and directed.

M&L for cutting chases in Stone concrete block or slab, walls , pinning in , making good to facing where required and pointing in cement mortar 1:3 to ends of edges of landing steps, cells, sun shed, shelves, lintels, etc ; and cutting cheese for water tubing or concealed conduit wiring , etc, and making good cutting not exc 10 cm girth complete all as specified and as directed.

Demolition of reinforced cement concrete in ground floors for leveling of and pavings not exceeding 15 cm thickness including floor finish complete all as specified and directed by Engr-in-Charge

Reinforced cement concrete, 1:2:4, type A-1 (using 20 mm graded stone aggregate) as in beams/bends supported on walls, beams and columns in floor, roofs, landings, balconies, canopies, shelves and like complete all as specified and directed.

M&L for Formwork to sides and soffits of floor or roof beam, beam hunching girders, bressum-mers, lintels cantilevers, shelves including supports, overhangs etc also splays between floors and beams, etc complete all as specified and directed.

TMT mild steel bars, 10mm dia and over, as in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with MS wire (annealed not less than 0.9mm dia) all as specified and directed.

TMT steel bars, 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with MS wire (annealed not less than 0.9mm dia) complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from metal/ Aluminium frames including punching or drilling out old glazing pins/ spring clips complete all as specified and directed.

S&F in repairs 3 mm thick Sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane complete all as specified and directed.

S&F in 3mm Figured glass, pin head type and glazing with oil putty in squares n exc 0.5 sq. m in each pane complete all as specified and as directed.

S&F in repair Galvanised mild steel wire cloth, 0.56 nominal dia of wire & average width of aperture 1.18mm with tinned tacks, or galvanised wire staples complete all as specified and as directed.

Taking down Chowkats or frames exc 1.5 Sqm but not exceeding 4 Sqm each (Without taking off shutters from the frames) complete all as specified and directed

-ditto- but n.exc 1.5 Sqm each complete all as specified and as directed.

Taking down shutters of any descp n.exc 1 sqm each complete all as specified and as directed.

Taking down shutters of any descp exc 1 sqm but n.exc 2 sqm complete all as specified and as directed.

,-ditto- but exceeding 2 Sqm each complete all as specified and as directed.

Re-fixing in same opening shutters of any descp exc 1 sqm but n.exc 2 sqm complete all as specified and as directed.

Re-fixing in same opening shutters of any descp exc 2 sqm complete all as specified and as directed.

S&F 125x60mm Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, hold fast etc., and back recess to be filled with pcc (1:3:6) type C-o concrete complete all as specified and as directed.

S&F 105x60mm Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, hold fast etc., and back recess to be filled with PCC (1:3:6) type C-o concrete complete all as specified and as directed.

Cutting holes in brick walls built in cement mortar and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required exc hail but n.exc one brick complete all as specified and as directed.

S&F 30mm thick Flush shutter, solid core construction, with block board core and plywood face panels, commercial type on both sides (Sample of Doors Bldg No. NP-23 HQ 71 Sub Area) complete all as specified and as directed.

S&F 35mm Glazed and skeleton shutters, 2nd class H.W open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitered beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and as directed.

S&F Factory Made Solid PVC Molded Door Shutter wall nut colour, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing but 2mm thick Moulded Prelim PVC Sheet on the front ace & 2mm Plain colour PVC Sheet on back face complete all as specified and as directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm wall nut colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening as per specification & drawing complete all as specified and as directed.

Factory made pressed steel frame steel window/ vent with glazed & gauged shutter (combined with side hung shutters incl box type hinges, steel handle, necessary locking arrangement, peg stay complete with one shop coat of zinc chrome primer including PCC (1:3:6) type -0 filling in back side recess profile portion, complete all as specified and directed by Engineer In Charge. Note : Rate quoted are included for wire gauged shutters and glazed window shutters complete & shall be measured as overall out to out one side only.

S&F floor door stopper of 140 mm long of aluminium alloy body and tongue, anodised with hard drawn steel spring, complete all as specified and as directed.

S&F 300 mm Mild steel sliding door bolts, plate type, stove enameled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and as directed.

S&F in repairs MS helical door spring 300mm size including roller and roller plate fixed to wooden or steel frames with welding/fitted with screws etc, complete all as specified and as directed.

S&F Aluminium powder coated (match with door shutters) Hydraulic door closer suitable for aluminium glass door shutters of 851 to1000 mm in width and of weight between 61 to 80 kgs and fixed complete all as specified and as directed. Make- Godreg/Jindal

S&F 150 mm Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and as directed.

S&F 150 mm Extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed.

S&F 100 mm Butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified and as directed.

Taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and as directed.

M&L for rendering 15 mm thick on fair faces of brick work in cement mortar 1:4 finished even and smooth without using extra cement and with using Water proofing compound .(Water proofing compound shall be measured and paid separately) complete all as specified and as directed.

M&L for rendering 10 mm thick in cement mortar 1:6 on fair face on brick/concrete surfaces and finished even and smooth without using extra cement complete all as specified and as directed.

M&L for two coat of cement base paint over a coat of alkali resistant primer paint including preparation of newly plastered of wall complete all as specified and as directed.

M&L two coats of oil bound distemper over a coat of primer over two coats of approved wall care putty over and including preparation of new plastered surfaces of wall complete all as specified and as directed.

M&L for preparation of new wooden surfaces of any description, not otherwise described over 10 cms width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and as directed.

S&F in repairs Brass CP shower rose 125mm size shower arm 15mm size, 195mm long with bend of 45 degree with flange complete all as specified and as directed.

S&F PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and as directed.

S&F PVC connections 15mm size with PTMT nuts of length 600 mm

S&F Gratings, fixed in repairs complete all as specified and as directed.

Demolition of stone slabs and tiles laid bedded and pointed in any mortar of any description or thickness in floors, aprons etc complete all as specified and directed.

Machine cut kotta stone slab flooring 20-25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the incl rubbing and polishing complete over and including screed bed 20 mm thick in CM 1:4 complete all as specified and directed.

--Ditto-- but on vertical surfaces as risers incl M&L 5 mm thick screed in CM 1:4 complete all as specified and directed.

M&L marble strip cut to width n.exc 100mm wide fixed as border in floor, stair case walk ways etc., incl rubbing and polishing complete over and including screed bed 20 mm thick in CM 1:4 complete all as specified and directed

M & L for Red/Black granite (of any type)stone slab 16mm thick machine cut as in pillars/ staircase/ window cells/counter top slab bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing with rounding to edges of stone slabs one edge complete Including 10mm thick backing coat CM 1:4 complete all as specified and directed.

M&L for 16-18 mm thick Green marble stone slab window cells incl bull nosing rounding edges directed colour, 18 mm thick machine cut,as in cells/skirting/ dado bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing, over 10mm thick rendering in CM 1 :4 complete all as specified and as directed.

Supply only integral water proofing compound complete all as specified and as directed.

S&F in repair Corner glass shelf with assembly complete all as specified and as directed.

Demolition/Dismantling boarding, ceiling boards, fiber pub insulation etc or insulation boards/ slabs/ blankets, any thickness, including cover and grid, complete all as specified and directed by the Engr-in-Charge.

S&F 18/19 mm thick Prelaminated MDF board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with crews to timber frame work as in Cupboard, kitchen cabinet or similar work etc including provn of 6mm thick teak wood lipping alround the board/ shutter complete all as specified and as directed.

S&F 30mm Continuous (piano) hinges, mild steel, bright finish or electro galvanised complete all as specified and as directed.

S&F Aluminium handles, cast type, anodised 100mm long complete all as specified and as directed.

S&F 100 size Hasp and staple, Aluminium Anodised, including bolt to hinge plate and fixed with screws complete all as specified and as directed.

S&F magnet catchers 50mm steel plate MS body and striking plate incl letting in & fixed complete all as specified and as directed.

S&F in repairs stainless steel multipurpose basket in wooden drawers/partitions for storing rations of various types made of 3 to 4mm dia stainless steel rods, fixed in side partitions etc fixed, complete all as specified for modular kitchen complete all as specified and as directed.

S&F in repair stainless steel zero crank hinges (auto) fancy type (with Euro concealed hinges) fixed to shutters in cupboards of standard size and shape for modular kitchen, complete all as directed by Engr-in-Charge.

S&F in repairs telescopic drawer side channel of std size and incl of roller for moving drawer, mild steel bright finish, or electro galvanised, for modular kitchen, complete all as specified and as directed.

Dismantling of Asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings complete all as specified and directed by the Engr-in-Charge.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed by the Engr-in-Charge.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50 mm of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall/ valley gutter/ Barge board, fixed with self tapping screws complete all as specified and directed by the Engr-in-Charge.

8mm Honeycombed Double wall Polycarbonate roof sheeting as per sample fixed in curve or circular area with MS flats iron as per site requirement fixed with coach screw and washer/J hooks or L hooks in roof, wall , complete all as specified and directed by Engr-in-Charge

S&F aluminium wind Tie with screwed ends, nuts, washers & mild steel plates for walls, chimneys, roofs, arches, etc. king rods & straining bolts complete all as specified and directed by Engr-in-charge.

Dismantling timber scantlings in fillets, rails, posts, rafters, purlin, etc.in any size, in any position complete all as specified and directed by the Engr-in-Charge.

Dismantling framed trusses in any length complete all as specified and directed by the Engr-in-Charge.

S&F Roof trusses (framed) , trussed , purlin, cross gantries and fastening and heavy brackets framing (Beam, tee, angle, channel ,flat section and MS Plates ) including distance pieces cleats etc. Fe-410-w (Gde- E-250) quality 'A' complete all as specified and directed by the Engr-in-Charge.

S&F Mild steel screw bolts (machine made) with hexagonal / square heads at one end & screwed the other/ screwed both ends, each screwed end to be fitted with washers & one hexagonal or square nut in any sizes complete all as specified and directed by Engr-in-Charge.

M&L for preparation of new steel and iron surface of any description, not otherwise described, over 10 cm width or girth applying two coat of synthetic enamel paint over one coat of primer any shade as approved complete all as specified and directed by the Engr-in-Charge.

M&L for preparation of old steel and iron surface of any description, not otherwise described, over 10 cm width or girth applying two coat of Aluminium paint and over coat of aluminium red oxide priming with any shade as approved all as directed and specified.

M&L for rendering 5 mm thick in cement mortar 1:3 on ceiling without using extra cement complete all as specified and directed by Engr-in-Charge.

M&L applying of new plastered surfaces of ceiling and applying two coat of white washing , complete all as specified and directed by Engr-in-Charge.

S&F false ceiling with cement designer tile white painted (high pressure steam cured) of 4 mm thickness (as per IS:14862) of size 595x595mm and any one of the design (oceanic, lake & hill, cascade or electra) in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 gms, both side inclusive) consisting of main 'T' runner with suitably spaced joints to get required length, and 15x32 mm made of 0.30 mm sheet, and cross 'T' at 600mm c/c to form a grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc . Main 'T' runners to be suspended from ceiling using GI soffit cleats fixed to existing rafter, purlin, etc with galvanised Butterfly level clips, spaced at 1200 mm c/c along main T, bottom exposed width of 15 mm of all T- sections shall be central black pre-painted with polyester paint, and having a load bearing capacity of 12 kg/sqm, and re-fixed all existing electric wiring and fixtures all complete at all heights as per direction of Engr-in -Charge.

S&F in repairs of false ceiling boards of Everest Fiber Cement Designer tile white painted (High Pressure Steam Cured) of 4mm thickness (as per IS-14862) of size 1220mmx1220mm/1195mm x595mm/1220mmx610mm or any other suitable size as per existing grid frame work and any one of the design (oceanic , lake & hill, cascade or electra) in true horizontal level, suspended on existing inter locking metal grid including required cutting/making opening for services like fixed over existing grid including necessary scaffolding etc and re-fixed all existing electric wiring and fixture all complete at all heights as per direction of Engr-in-charge. Make-Everest/Visakha

,-ditto- but except ceiling board removing and re-fixing existing board

Supplying and fixing in repairs grid frame suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 gms, both side inclusive) consisting of main 'T' runner with suitably spaced joints to get required length, and 15x32 mm made of 0.30 mm sheet, and cross 'T' at 600mm c/c to form a grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc . Main 'T' runners to be suspended from ceiling using GI soffit cleats fixed to existing rafter, purlin, etc with galvanised Butterfly level clips, spaced at 605 mm X 605 mm c/c along main T, bottom exposed width of 15 mm of all T- sections shall be central black pre-painted with polyester paint, and having a load bearing capacity of 12 kg/sqm, and re-fixed all existing electric wiring and fixtures all complete at all heights as per direction of Engr-in -Charge.

M&L for preparation old wooden surfaces of any description, not otherwise described over 10 cms width or girth and applying two coats of synthetic enamel paint over one coat of pink primer, complete all as specified and as directed.

Demolition of un-reinforced cement concrete in ground floors for leveling of and pavings not exceeding 15 cm thickness including floor finish complete all as specified and directed by Engr-in-Charge.

Material and labour for 50 mm thick plain cement concrete type C-1 1:3:6(Using 20mm graded crushed stone aggregates) as in plinth protection finished fair and even without using extra cement complete all as specified and directed. Note : The plinth protection shall be laid in panels and length of the each panel shall not be more than 2.00 metre all as directed. 6mm joints filled with 85/25 grade bitumen and sand (1:3 ratio) shall be provided. No deduction for joints shall be made while making payment against the above item complete all as specified and directed by Engr-in-Charge.

Providing and fixing power coated aluminium (minimum thickness of power coating 50 micron) for shutters of doors, windows and ventilators including providing and fixing hinges/pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (fitting shall be paid for separately) with extruded built up standard tubular section /appropriate Z section and other section of approved make conforming to IS:733 and IS:1285 fixing with dash fastener of required dia and size, including necessary filling up the gaps at junctions i.e. top, bottom and sides with required EPDM rubber/neoprene gasket and sliding roll etc. Aluminiums section shall be smooth ,rust free, straight mitred and jointed mechanical wherever required including cleat angle, aluminium snack bedding for glazing/paneling ,CP brass / stainless steel screws rail as complete as per architectural drawing and the direction of Engr-in-Charge. .

Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with aluminium anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/stainless steel screws @ 200 mm centre to centre , including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engr-in-Charge. .

S&F Glazing with 5mm thick frosted/tinted sheet glass n.exc 0.50 sqm in each panel fixed to aluminium section of doors, windows and fixed frame with suitable EPDM rubber packing and powder coated aluminium beading to frame complete all as specified.

S&F Stainless steel mosquito proof wire cloth of stainless 0.36mm dia and 1.4mm aperture fixed with aluminium flat/channel and screws all as specified as directed by Engr-In-Charge.

M&L for plain cement concrete 1:3:6 type C-1 (using 12.5mm graded stone aggregate) as in roof padding/ leveling coarse between wall and roof sheet or chamfered finished even and smooth with using extra cement complete all as specified and directed by Engr-in-Charge.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends swan necks, etc, including cleaning or re-fixing or removal to store (measured overall as fixed along the centre line over fitting and accessories).

S&F PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and as directed.

S&F PVC (SWR) pipes 110mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and as directed.

All as per Srl item No.60 above but as in re-fixing only with stack clamp to wall complete all as specified and as directed.

S&F 110 mm bore PVC (SWR) bends with access door any radius, all as specified and directed by the Engr-in-charge.

S&F PVC (SWR) bends 75 mm bore any radius with overall & access door complete all as specified and as directed.

S&F 110 mm bore PVC (SWR) bends with access door any radius, all as specified and directed by the Engr-in-charge.

S&F PVC (SWR) junction single, (Single T/Y in with Access door) 75mm equal or unequal complete all as specified and as directed.

S&F PVC (SWR) junction single, (Single T/Y jn with Access door) 110 mm equal or unequal complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

M&L for 75mm thick cement concrete 1:4:8 type D-2 using 40mm graded crushed stone aggregates as in sub base to receive floor rough finishes complete all as specified.

M&L glazed ceramic coloured tiles in vertical surface 450X 350X 7mm thick and above nearest sizes set and jointed in neat cement slurry and pointed in white or colour cement to match including 10 mm screed bed in 1:3 cement mortar complete all as specified and as directed.

M&L non-skid coloured Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm screed bed 1:4 cement mortar complete all as specified and as directed.

S&F Coloured Glazed ceramic tiles in vertical surfaces 600x300mmx7mm thick and above nearest sizes set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm screed bed in 1:3 cement mortar complete all as specified and as directed.

S&F Non Skid coloured ceramic tiles 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm screed bed 1:4 cement mortar complete all as specified and as directed.

Dismantling of wall and ceiling boards (Fibre, Pulp, Insulation, Etc.) or insulation boards/slabs/blankets any thickness including cover fillets complete all as specified and directed by Engr-in-Charge.

S&F 5mm thick (HL Series) insulated PVC Wall Lining honeycombed consisting of PVC Insulated Panels (As per approved by GE) with approved design & pattern duly fitted into the wall including PVC angle Jointers, U jointers, beading etc as required at the edges including removing and re-fixing electric boards & plates and covered with PVC strips or beading after fixing wall paneling including dismantling of old PVC wall paneling , complete all as specified and directed by Engr-in-Charge.

Checking of plumbing work ,mason work and joinery (wooden/steel) iron/aluminium mongery, pelmet box, door springs etc requiring carpentry/ plumbing/ mason work and carrying out minor repairs such as tightening of screws/nails, minor adjustment of joinery, door/ windows, water taps, stop cocks, water tank, water supply pipe line etc. by means of planer/chiseling etc. including petty repairs material like screws/nails, plug, cement, sand, aggregate etc. to make it functional, complete all as specified and directed. Note : 1. Any items required to be replaced shall be paid under respective items and in that case this items shall not be measured and paid. 2. The contractor or his authorised rep shall collect the complaint of all carpenter work from complaint cell /JE/Engr-in-charge daily and all complaint will be rectified by the contractor with in same day than the returned the complaint slip after completion of complaint and get receipt from concerned JE/ Engr-in-charge .If he fails to complete the work with in same day then recovery will be made @ 250.00 per day per complaint .

S&F 12 mm thickness Toughned glass as in hinged doors, partition automatic doors, partitions etc. and similar work including cutting to shape, drilling holes required complete all as specified and directed by Engr-in-Charge.

S&F curtain rod stainless steel knobs onion shape or any other shape complete all as specified and directed by Engr-in-Charge.

S&F curtain rod stainless steel brackets complete all as specified and directed by Engr-in-Charge.

Taking down carefully the existing Copper/Aluminium point wiring of any size and type by disconnecting from the either terminals complete with switches, sockets, ceiling rose, regulators, bell etc by unscrewing and removing materials to store for keeping in safe custody for re-use or for taking credit and making good to disturb surface of walls, floors etc., complete all as specified and directed by Engr-in-charge. Note : (i) Old dismantled wiring and accessories (other than reuse) will be contractors property and credit will be charged against schedule of credit.

Taking down carefully by unscrewing from boards / outlet boxes fittings and fixture such as, LED bulk head fitting, LED tube light fitting etc. for re use at site or carrying to the store (serviceable fitting shall be reuse) all as specified and as directed by Engr-in-charge..

Taking down Old Serviceable/unserviceable MCB DB any type/ size etc after disconnecting (serviceable DBs /MCBs shall be reuse), complete all as specified and directed by Engr-in-charge..

M&L for Point wiring for One light point controlled by one way switch 5 Amp with 1.5 Sqm single core multi standed copper conductor FRLS insulated and unsheathed heavy duty cable in colour code including continuous earth wire with cable of size 1.5 sqm copper conductor flexible FRLS insulated drawn into and including concealed PVC rigid conduit of not less than 20mm dia and1.5mm wall thickness ISI marked terminated into annealed steel terminal boxes including 3.00 mm thick hylam brand IS-2036 marked, laminated sheet cover for mounting switches, sockets, fan regulators etc complete all as specified and directed by the Engr-in-charge.

M&L for point wiring with 1.5 Sq. mm PVC Insulated unsheathed FRLS multi stranded copper conductor, medium grade ISI marked drawn into and including PVC concealed conduit with all accessories from terminal box to junction of ceiling and wall and rest of circuit conductor wire drawn in to and including surface PVC rigid non metallic conduit for one ceiling fan point controlled by one switch with and also including 1.5 sqm continuous earth wire connected to common earth dolly complete all as specified and directed by Engr-in-charge.

All as per item No. 175 above but for bell / buzzer on independent board controlled by one push button bell switch.

All as per item Srl No. 175 herein before but for 3 pin socket outlet 5 Amp on same board, complete all as specified and directed by Engr -in-charge.

All as per item No. 175 above but for one 5 Amps socket outlet on independent board.

All as per item No. 175 above but wire size 2x2.5 Sqm to controlled the 3 pin 5 / 15 Amps socket outlet on independent board and providing earth continuity wire using PVC insulated, FRLS 1100 volts grade un sheathed single core stranded copper conductor cable of size 2.5 Sqm.

All as per item No.175 above but control by 2 Nos. of two way switch.

M&L Point wiring with multi stranded copper conductor cable, PVC insulated and unsheathed (FRLS) size 1.5 sqm drawn in and incl PVC casing and capping /PVC conduit with fixing accessories, to be fixed on wooden gut ties or plastic rawal plug, for one light /fan/controlled by one switch with thickness not less than 1.25mm annealed steel boxes concealed on wall with and including 3mm thick laminated backlight sheet complete all as directed by Engr-in-Charge. .

All as per item No 182 above but for two way point wiring

All as per item No 182 above but for one 3/5 pin socket 5 Amp on same board with cable1.5 sqm size.

All as per item No 182 above but for one 3/5 pin socket 5 Amp on independent board with cable1.5 sqm size.

All as per item No 182 above but for 3/5 pins socket outlet 15 Amps independent with 2.5 sqm incl continuous earthing with multi standred copper conductor PVC insulated unsheathed size 2.5 Sqm complete all as specified and directed.

All as per item No. 182 above but for bell / buzzer on independent board controlled by one push button bell switch.

S&F Switch Piano flush type single pole 5 Amps One way, all as specified and directed by Engr- in - Charge. Make : Anchor Penta Cherry of Ordering Code : 14121/ Havells REO Cat No: AHESXXW061

S&F Switch Piano flush type single pole two way 5/15 Amps, all as specified and directed by Engineer- in - Charge.Make : Anchor Penta Cherry of Ordering Code : 14122/Havells REO Cat No: AHESXXW062

S&F Socket outlet Two in one, 3/5 Pin piano type 5 Amp flush type complete all as specified and directed by Engr-in-charge. Make : Anchor Penta Ordering Code : 14119/Havells REO Cat No: AHEKSWW063

S&F Switch Piano type single pole 16/20 Amps One way, complete all as specified and directed by Engr-in-charge. Make : Anchor Penta Ordering Code : 39991/ Havells REO Cat No: AHESXXW201

S&F Socket outlet Two in one, 3/5 Pin piano type 10 Amp and 20 Amp flush type complete all as specified and directed by Engr-in-charge.. Make : Anchor Penta Ordering Code : 39994/ Havells REO Cat No: AHESYXW161

S&F Ceiling rose, 3 terminal, PVC / polycarbonate, isolated body complete all as specified and directed by Engr-in-charge. Make: Anchor Ordering Code : 39072/ Havells REO Cat No: AHEEIXW000

S&F Electric bell (Ding dong) AC 230/250 volts grade single pole ISI marked, complete all as specified and as directed by Engr-in-charge. Make : Havells REO Ordering code : AHELEXW000/ ANCHOR

S&F switch piano flush type for bell Push 5 Amps, complete all as specified and directed by Engr-in-charge. Make : ANCHOR Penta Cherry,Ordering Code : 14123/ Havells REO Ordering code : AHEMBKW061

S&F Electronic type fan regulator Stepped type, 240Volt flush type suitable for 1200/1400mm sweep ceiling fan, ISI marked complete all as specified and directed by Engineer- in - Charge. Make : ANCHOR Penta Cherry,Ordering Code : 14123/ Havells REO Ordering code : AHEMBKW061

Taking down fan, ceiling cable end, dismantling blades and kept in safe custody for refixing on same location all as specified and directed by Engr-in-charge.

Hanging /fixing only ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan obtained from item No 197.

S&F in repair LED light fitting with high out put diffuser 1 feet, 5 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed by Engr-in-charge..

S&F in repair LED light fitting mirror type with high out put diffuser 2 feet, 10 /12 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed by Engr-in-charge.

S&F in repair LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed by Engr-in-charge.

S&F in repair LED Bulk head (6500K) fitting of 09/10 Watt surface mounting type extruded aluminium body with diffuser complete with testing all as specified and directed by Engr-in-charge..

S&F in repair surface/recessed mounting LED luminaries 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as specified and as directed by Engr-in-charge.. .

S&F in repair surface/recessed mounting LED down lighter round/square shape 12 watt 220 volts AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as spesified and directed by Engr-in-charge.

M&L in replacement for sub main wiring with 2X4QMM+1X4SQMM Earth Wire single core PVC insulated FRLSH sheathed cooper cable connecting to common earth dolly in and including heavy duty PVC Concealed Conduit 25MM DIA complete including taking down unserviceable sub main wiring all as per site requirement and direction by EIC, all accessories complete all as specified and directed.

Sub main wiring with two run single core 6.0 sqm FRLS copper conductor cable connected to earth dolly in and including heavy duty PVC concealed conduit 25 MM dia, complete all as specified and directed by Engr-in-charge. Note : Two run of 6.0 sqmm and one run 6.0 sqmm cable and one run of PVC casing and capping shall be measured as one RM

Sub main wiring with two run single core 10 sqm FRLS copper conductor cable connected to earth dolly in and including heavy duty PVC concealed conduit 25 MM dia, complete all as specified and directed by Engr-in-charge. Note : Two run of 10 sqmm and one run 10 sqmm cable and one run of PVC casing and capping shall be measured as one RM

Sub main wiring with two run single core 1.5 sqm FRLS copper conductor cable PVC insulated, unsheathed, 1100V grade including 25mm dia in PVC concealed conduit/PVC casing & capping medium grade ISI marked with all accessories such as Tees, elbows, junction boxes etc, as required fixed on wall alongwith one run of 6 sqm single core PVC FRLS insulated unsheathed copper conductor cable as continuous earth wire and connecting to existing main switch board/distribution board complete including taking down unserviceable sub main of any type/size and testing on completion etc fixed in replacement, complete all as specified and directed by Engr-in-Charge. Note : Two run of 1.5 sqm and one run1.5 sqm cable and one run of PVC conduit shall be measured as one RM

Sub main wiring with two run single core 2.5 sqm FRLS copper conductor cable PVC insulated, 1100V grade including 25mm dia in PVC concealed conduit/PVC casing & capping medium grade ISI marked with all accessories such as Tees, elbows, junction boxes etc, as required fixed on wall alongwith one run of 2.5 sqm single core PVC FRLS insulated unsheathed copper conductor cable as continuous earth wire and connecting to existing main switch board/distribution board complete including taking down unserviceable sub main of any type/size and testing on completion etc fixed in replacement, complete all as specified and directed by Engr-in-Charge. .Note : Two run of 2.5 sqm and one run2.5 sqm cable and one run of PVC casing and capping shall be measured as one RM

Supply and fix VTPN MCCB Double door Distribution Board 04 way 415 volts grade IP 43 Protection Grade with provision for (MCCB) as incoming and Three/single phase (TP/SP) outgoings, complete with insulated bus bar arrangement fixed flush to wall complete including connections should be provide with necessary reducer lugs all as specified and directed by Engr-in-charge. Make : C&S Cat No:CSDBMCCB100DD04IP43S/ Standard Cat No: DSDLVDRBAOFO04/ Indo Asian Cat No : 811888

S&F in replacement single pole and neutral sheet steel powder coated distribution board for MCBs fitted with bus bar neutral link Earth bar and din rail suitable for use on 240V, 50Hz supply double door SPN DB system 4 Way all as specified and directed by Engr-in-charge. Make : C&S Cat No:CSDBSPNDD08/ Standard Cat No: DSDNSHODXW08/ Indo Asian Cat No : 810321

S&F in replacement single pole and neutral sheet steel powder coated distribution board for MCBs fitted with bus bar neutral link Earth bar and din rail suitable for use on 240V, 50Hz supply double door SPN DB system 8 Way all as specified and directed by Engr-in-charge.. Make : C&S Cat No:CSDBSPNDD08/ Standard Cat No: DSDNSHODXW08/ Indo Asian Cat No : 810321

S&F in replacement single pole and neutral sheet steel powder coated distribution board for MCBs fitted with bus bar neutral link Earth bar and din rail suitable for use on 240V, 50Hz supply double door SPN DB system 12 Way all as specified and directed by Engr-in-charge.. Make : C&S Cat No:CSDBSPNDD12/ Standard Cat No: DSDNSHODXW12/ Indo Asian Cat No : 810323

S&F in repair for MCB TPN 63 Amp, 415 Volts- C curve of 10kA Make : C&S Cat No: CSMBS3C63N/ Indo Asian Cat No 810098/ Havells

S&F in repair Metal clad Plug socket single pole enclosure with two pin earth plug and socket with one single 20 Amp , 240 volts MCB complete all as specified and directed by Engr-in-charge.

S&F in repair energy saving LED garden light fitting, decorative, bollard type of capacity 9/11 watt with opal diffuser & aluminium reflector complete with all accessories and fixing arrangement on PCC block of size 45mm X 45 mm alogwith fixing nuts, bolts and PVC insulated aluminium conductor, stranded type of size 4.0 sqmm,2 -core including taking down old/ unserviceable garden light fittings any type and wattage all as directed. Make - C&S cat pt No- LTGLCW9WLED,Havells cat pt No- LHEVBDP7IN6K008,Crompton & Greaves-LPTO-40-CDL-M

S&F LED street light fitting 25/35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as directed.

S&F in repair decorative LED gate light fitting of 30/40 watt,240 volts, diecast aluminium housing in pure polyster powder coated grey finish, top maintainable product with opening die cast cover, anti corrosive stainless steel screws & silicon gasket, HET PMMA diffuser,IP65 protection driver duly prewired up to terminal on firms to IS 10322 part 5/sec, 1 :1987,suitable for pole of dia 65-75 mm in-built electronic driver complete including taking down old/unserviceable gate light fitting complete all as specified and directed .Make - Crompton & Greaves Cat part No -LPT0-40-CDL or equivalent in Bajaj/Havells/C&S/ Philips/Wipro

S&F in repair Thermal magnetic MCCB 4 pole 63 Amps 415 Volts 16 ka INCLUDING MAKING NECESSARY ARRANGEMENT all as specified and directed by Engr-in-charge. for MCCB DB.Make C&S Cat No: CSC2N4/ Indo Asian Cat No: 830022/ or equivalent makes to Standard

S&F in repair Thermal magnetic MCCB 4 pole 100 Amps 415 Volts 16 ka INCLUDING MAKING NECESSARY ARRANGEMENT all as specified and directed by Engr-in-charge. for MCCB DB. Make C&S Cat No: CSC2N4/ Indo Asian Cat No: 830022/ or equivalent makes to Standard

S&F in repair Thermal magnetic MCCB 4 pole 125/160 Amps 415 Volts 16ka INCLUDING MAKING NECESSARY ARRANGEMENT all as specified and directed by Engr-in-charge. for MCCB DB. Make C&S Cat No: CS3A4/ Indo Asian Cat No: 830095 / or equivalent makes to Standard

S&F in repair connection and testing 'C' series SPN MCB 40 to 63 Amp 240V, 50Hz, 10kA for lighting and other domestic loads incl necessary copper lugs etc all as specified and as directed by Engr-in-charge. Make C&S Cat No: CSMBS2C40/ Indo Asian Cat No: 810078/ or equivalent makes to Standard

S&F in repair 'C' series MCB SP6-32 Amps. Make C&S Cat No: CSMBS1C6 to CSMBS1C32/ Indo Asian Cat No: 810078/ or equivalent makes to Standard

S&F in repair 'C' series MCB SP 40 Amps. Make C&S Cat No: CSMBS1C40/ Indo Asian Cat No: 810060/ or equivalent makes to Standard

Fixing only serviceable MCB SPN/SP any capacity obtained from item no 03 as above all as specified and as directed by Engr-in-charge.

Fixing only serviceable LED tube light fittings of 5w/12W/20W/2'x2' panel light and LED bulk head fitting 9W as obtained from Srl item No-02 above complete with all a fixing accessories.

Fixing only serviceable MCB DB of any type and capacity obtained from Item No 03 complete all as specified and directed by Engr-in-charge.

S&F in repair Switch Piano flush type single pole two way 5 Amps fixed in replacement, complete all as specified and directed by Engineer- in - Charge. Make : Anchor Penta Cherry of Ordering Code : 14122/Havells REO Cat No: AHESXXW062

S&F in repair Switch Piano flush type single pole 5 Amps one way fixed in replacement, complete all as specified and directed by Engineer- in - Charge. Make : Anchor Penta Cherry of Ordering Code : 14121/ Havells REO Cat No: AHESXXW061

S&F in repair switch piano flush type for bell Push 5 Amps fixed in replacement, complete all as specified and directed by Engineer- in - Charge. Make : ANCHOR Penta Cherry, Ordering Code : 14123/ Havells REO Ordering code : AHEMBKW061

S&F in repair Socket outlet Two in one, 3/5 Pin piano type 5 Amp flush type fixed in replacement, complete all as specified and directed by Engineer- in - Charge. Make : Anchor Penta Ordering Code : 14119/Havells REO Cat No: AHEKSWW063

S&F in repair Socket outlet Two in one, 3/5 Pin piano type 5 Amp and 15 Amp flush type fixed in replacement, complete all as specified and directed by Engineer- in - Charge. Make : Anchor Penta Ordering Code : 39994/ Havells REO Cat No: AHEKYXW163.

S&F in repair Switch Piano type single pole 16/20 Amps One way, fixed in replacement, complete all as specified and directed by Engineer- in - Charge. Make : Anchor Penta Ordering Code : 39991/ Havells REO Cat No: AHESXXW201

S&F in repair Switch socket combination piano type 5 pin 5 Amps flush type fixed in replacement, complete all as specified and directed by Engineer- in - Charge. Make : Anchor Penta Ordering Code : 38820/ Havells REO Cat No: AHETOXW062

S&F in repair Switch socket combination piano type 6 pin 16 Amps flush type fixed in replacement, complete all as specified and directed by Engineer- in - Charge. Make : Anchor Penta Ordering Code : 39998/ Havells REO Cat No: AHETOXW204

S&F in repair Switch socket combination box type 5 pin 5 Amps flush type fixed in replacement, complete all as specified and directed by Engineer- in - Charge. Make : Anchor Penta Ordering Code : 39998/ Havells REO Cat No: AHETOXW204

S&F in repair Switch socket combination box type 6 pin 16 Amps flush type fixed in replacement, complete all as specified and directed by Engineer- in - Charge. Make : Anchor Penta Ordering Code : 39998/ Havells REO Cat No: AHETOXW204

S&F in repair Ceiling rose, 3 terminal, PVC / polycarbonet, isolated body fixed in replacement, complete all as specified and directed by Engineer - in - Charge. Make: Anchor Ordering Code : 39072/ Havells REO Cat No: AHEEIXW000

S&F in repair Electronic type fan regulator Stepped type, 240Volt flush type suitable for 1200/1400mm sweep ceiling fan, ISI marked fixed in replacement, complete all as specified and directed by Engineer- in - Charge. Make : ANCHOR Penta Cherry, Ordering Code : 14123/ Havells REO Ordering code : AHEMBKW061

S&F in repair Electric bell(Ding dong) AC 230/250 volts grade single pole ISI marked fixed in replacement, complete all as specified and as directed by Engr-in-charge.. Make : Havells REO Ordering code : AHELEXW000/ ANCHOR

M&L for disconnecting all Electrical connection from MCB DB TPN/Wall Mounted Panel Box for reconnecting the same with providing proper Copper Bottle Lugs of suitable size and removing the burnt out internal wiring of DB/Panel complete with providing PVC Flexible conduit for Hanging wire complete all as specified and directed by Engr-in-charge.. Note : Replacement Burnt out MCBs of any type/size may be measured and paid separately under relevant Items

Taking down/removing existing damaged cable connection from MCB DB/Wall Mounted Panel Board by making cutting chases on wall/ floor to extend the shorten UG cable of any type/size from Loop and making fresh to reconnect the same with suitable aluminium lugs complete including distribute the load equally on each phase all as specified and directed by Engr-in-charge.. Note : Cutting of Wall / Floor shall be measured and paid separately.

M&L for Cutting of hard standing n.exc 45 Cm depth, and n.exc 30 Cm width for taking out/laying UG Cable including making good disturbed surface as per existing all as directed .

S&F in repair Modular fan step regulator 120W 02 module including taking down unserviceable one all as specified and as directed by Engr-in-charge. Make : Legrand or equivalent to Schnider/Havells

S&F in repair Modular switch 01 way 06A, 01 module including taking down unserviceable one all as specified and as directed by Engr-in-charge.. Make : Legrand or equivalent to Schnider/Havells

S&F in repair Modular switch 01 way 16A, 01 module including taking down unserviceable one all as specified and as directed by Engr-in-charge.. Make : Legrand or equivalent to Schnider/Havells

S&F in repair Modular bell push flush type 6A, 01 module including taking down unserviceable one all as specified and as directed by Engr-in-charge.. Make : Legrand or equivalent to Schnider/Havells

S&F in repair Modular socket, 6A-2/3 pin, 02 module including taking down unserviceable one all as specified and as directed by Engr-in-charge.. Make : Legrand or equivalent to Schnider/Havells

S&F in repair Modular socket, 6A/16A-2/3 pin, 02 module including taking down unserviceable one all as specified and as directed by Engr-in-charge.. Make : Legrand or equivalent to Schnider/Havells

S&F in repair PVC rectangular block for mounting switches, sockets, fan regulator etc. of size 200x150x50mm deep including making necessary cutting all as specified and as directed by Engr-in-charge., Make Anchor or equivalent to havells

S&F in repair PVC rectangular block for mounting switches, sockets, fan regulator etc. of size 250x200x50mm deep including making necessary cutting all as specified and as directed by Engr-in-charge., Make Anchor or equivalent to havells

S&F in repair 3 mm thick plastic laminated ebonite sheet cover of size 200x150mm including cutting /finishing or making hole for mounting of switches, sockets, regulators etc all as specified and as directed by Engr-in-charge..

S&F in repair 3 mm thick plastic laminated ebonite sheet cover of size 250x200mm including cutting /finishing or making hole for mounting of switches, sockets, regulators etc all as specified and as directed by Engr-in-charge..

M&L Earthing complete with galvanised steel earth plate electrode 60x60cmx6mm thick, buried directly in ground (earth pit not less than 2.25 meters deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No-3 of MES Part-1 fixed in replacement including testing on completion including the material and labour of the following :- (a) Excavation and earth work for drilling hole for electrode in any type of soil. (b) PCC Pit in cement concrete 1:2:4 type B-1. (c) Precast RCC cover with suitable handle 40mm thick in PCC 1:2:4 type B-1, reinforced with welded steel wire fabric weighing not less than 1.87 Kg/Sqm. (d) Funnel with watering pipe of GI protection pipe 5 mtr long for protection of earthing lead from mechanical injury or tempering. (f) Requisite quantity of common salt and charcoal. (g) Testing of Earthing. Note : (a) On testing after completion of earthing, if the desired earth resistance is not obtained, the earthing will be done by the contractor at his own risk and cost to the entire satisfaction ot the engineer incharge. (b) The contractor shall quote his rate considering taking down cost of existing unserviceable earthing.

DEV RAJ MAGOTRA

M/S IMTESH BHAT