REPAIR/REPLACEMENT OF GATE, REPAIR TO COMPOUND WALL, PATH, DRAIN, FENCING, CULVERTS, GARBAGE BINS AND SHEDS AND MISC WORKS IN OTM AND MD ACCN UNDER GE(SOUTH) MEERUT CANTT

Amount

Excavation in trenches not exc 1.50m wide and not exc 1.50m in depth for foundation area n.exc 10 Sqm on plan and getting out in soft/loose soil all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers n.exc. 25cm thick in soft / loose soil complete all as specified and directed.

Removing excavated soil to a distance not exc 50 m and deposited where directed at a level not exc 1.5 m above the starting point all as specified and directed.

Material and Labour for PCC 1:4:8 type D-2 (using 40mm graded stone aggregates) as in foundation fillings the mass concrete & sub base of floor all as specified and directed.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for and removing debris to a distance not exc 100m complete all as specified and directed.

Material and labour for providing reinforced cement concrete M 25 (Design mix) as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, basement slabs and mass concrete complete all as specified and directed.

Material and labour for providing reinforced cement concrete M 25 (Design mix) as in columns, pillars, piers, posts and struts complete all as specified and directed.

Material and labour for providing reinforced cement concrete M 25 (Design mix) as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

Material and labour for use and waste formwork to sides of concrete foundation, footings, bases of column, rafts, plinth beams and similar work vertical or to batter for rough finished flat surface of concrete , complete all as specified and directed.

Material and labour for use and waste formwork to sides of pillars, posts, struts, piers, columns and stanchions to give rough finished flat surface of concrete complete all as specified and directed.

Material & labour for TMT Bars 10mm dia and over cut to length bent to shape required inculding cranking bending spirally hooping for columns hooking ends etc and binding with and including mild steel wire annealed less than 0.9mm dia or securing with clips complete all as specified and directed.

All as per item No 11.00 above but herein 5mm dia and over upto and including 10mm dia as in stirrups spacers and binders etc complete all as specified and directed.

Demolition of brick work built in cement mortar or cement lime mortar including all quoins, arches, pillars etc complete all as specified and directed.

Material and labour for brick work with fly ash bricks straight or curved on plan exc. 6 metre mean radius built in cement mortar (1:6) complete all as specified and directed.

All as per item No 14.00 above but except bricks including old bricks for reuse.

Material and labour for brick work with fly ash bricks straight or curved on plan exc. 6 metre mean radius built in cement mortar (1:6) as in half brick wall complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc and including removal of debris and rubbish from the site complete all as specified and directed.

Material and labour for rendering, 15 mm thick on fair faces of brick or concrete surfaces in cement mortar 1:6, surfaces finished even and smooth without using extra cement complete all as specified and directed.

Material and labour for applying three coat of white wash on newly plaster surfaces of wall surfaces including preparation of surfaces all as specified and directed.

Materials and labour for preparation of old painted surfaces of wall and applying one coat of exterior emulsion paint complete all as specified and directed.

Material and labour for, pre-cast, 25mm thick cement concrete jali 1:2:4 type B0 (using 12.5 mm graded crushed stone aggregate) of size 600x750mm including all mouldings fixed in CM 1:4 all as specified and as directed by Engr-in-Charge.

Excavation in post holes (or similar holes) each n.exc. 0.5cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc. 25cm, watering and removing surplus soil to a distance n.exc. 50 m and making good surface complete all as specified and directed.

Taking down existing barbed wire of any description complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Dismantling chain link fencing wire mesh of any type complete all as specifed and directed.

Dismantling posts and struts (wood, steel or RCC) any sectioin, inlcuding takiing out embeded portion and making good disturbed ground complete all as specified and directed.

Material and Labour for PCC 1:3:6, type C-1 (using 20mm graded crushed stone aggregate) for foundation filling and mass concrete complete all as specified and directed

S&F Mild steel angle iron as in fencing posts, cut to length, drilling holes, welding and embedded in concrete complete all as specified and directed.

Fixing only chain link fencing including line wires, any mesh, size and type of standards, rails, straining bolts, etc. incl provision of binding wire complete all as specified and directed.

Supply only chain link MS galvanised fencing any type & size complete all as specified and directed. (Sample of chain link fencing shall be got appd from GE before bulk supply).

Supply and fix 40x5 mm flat iron as in fastening of chain link fencing fixed with nuts and bolts includng making holes complete all as specified and directed.

Supply and fix mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 5cm but n. exc 10 cm long, dia of neck 5 to 10mm complete all as specified and directed.

Supply only Mild steel in flat round or square bar Fe-410W (Gde E-250) quality 'A' in available length complete all as specified and directed.

Supply and fix galvanised 2 strand steel barbed wire 2.24 mm dia barbed with 2 mm dia bars at 75 mm spacing and straining and fixing to any type of standard rail, straining bolt including securing and tying at crossing with and including galvanised MS wire staple or steel pin etc ( Each line of wire to be measured ) complete all as specified.

Supply and fix for framed work such as grills, gratings with ends of bars shouldered and/ or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0 for portions framed and hung as gates, including pintle hinges, stops, hand-made sliding bolts complete all as specified and directed.

Material and labour for preparation of new steel surfaces and applying two coats of synthetic enamel paint over a coat of red oxide primer area n.exc 10 cm width or girth complete all as specified and directed

Material and labour for applying two coat of synthetic enamel paint over prepared old/new steel surfaces of any description, not otherwise described over 10Cm width or girth and complete all as specified and directed.

Supply and fix framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete of steel grade Fe-290, E-165 and including taking down old steel gate & removing from site complete all as specified & directed.

Supply and fixing mild steel works as in hold fasts etc and similar small articles confirming Fe-290 Gde-E-165 complete all as specified and directed.

S & F 1.6 mm thick Mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified & directed.

Dismantling, floor, hearth or wall tiling including cement mortar bedding but not backing plaster and removing rubbish off the premises complete all as specified & directed.

Material and labour for 10 to 12mm thick granite stone slab of any type as in wall lining, steps, column , pillars and steps like over and including 10mm thick backing cement screed in cement mortar 1:4, including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including moulding of edges complete all as specified and directed.

Material and labour Coloured / Black Glazed ceramic tiles in vertical surfaces 350x250mmx7mm / 450x350x7 mm thick, Joint free tiles set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick backing cement screed CM (1:4) complete all as specified and directed.

Material and labour for hardcore of broken stone of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complte all as specified and directed

Supply and fixing factory made precast kerb stones of size 300x300x150, of M-35 concrete, 100mm thick one side round edge as per sample (size and shape as approved by GE), set jointed and pointed in cement mortar in CM 1:3 as in patches , including necessary excavation and taking out existing damaged kerbs stones complete all as specified and directed.

Supply and fixing factory made precast machine pressed interlocking paver block , of M-35 concrete, 60mm thick (size and shape as approved by GE), grey colour with provision of interlocking joints, set jointed and pointed in neat cement slurry with grey cement, over and including 25 mm thick sand cousioning incl taking out exiting broken tiles/ block complete all as specified and directed.

Supply and fixing factory made precast machine pressed interlocking paving block , of M-35 concrete, 60mm thick (size and shape as approved by GE), RED colour with provision of interlocking joints, set jointed and pointed in neat cement slurry with grey cement, over and including 25 mm thick sand cousioning incl taking out exiting broken paver block complete all as specified and directed.

S&F factory made PCC type A-1 coloured rubberised laboroda chequered tiles 25 mm thick, of size 300x300mm, in floors, set and jointed with grey cement slurry & pointed in white cement mixed with pigment to match the shade of tiles over and including 15 mm thick cement screed bedding layer in CM 1:6 complete all as specified and directed .

Dismantling of Asbestos cement (corrugated semi corrugated etc) sheets in roof covering complete all as specified and directed.

Dismantling of wooden fillet rails, post rafter purlin etc under 40 Sqcm section (unframed) complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

M and L for 6mm thick fibre cement corrugated sheets in roofs, walls etc, fixed with L-type or J-type or cranked hook bolts including bituminous washers complete all as specified and directed.

Material and labour for fibre cement two piece adjustable serrated ridge, 6mm thick fixed with L-type or J-type or cranked hook bolts including bituminous washers complete all as specified and directed.

Supply and fix Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick having tensile strength of 550 Mpa as in roof covering fixed with self tapping screws complete all as specified and directed.

All as per serial item No 54.00 above but plain sheet as in ridge, gutter, flashing etc complete all as specified and directed.

M&L for structural steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes confirming to IS 1161-1979 grade st - 240 complete all as specified and directed.

M&L for mild steel work in roof trusses ( framed ) , purlin, rafter , fastening , distance pieces, cleats etc (incluidng fixing independently vertical post) complete all as specified and directed.

Supply and fix of structural steel works for plates (plain or chequered) channel, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe 410-W (Gde-E-250) quality-A complete all as specified and directed.

Material and labour for plain cement concrete 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate) as in surface channel, drains all as specified and directed.

Material and labour for extra forming fair finished drain or chanel 30 cm inner girth in cement concrete, using extra cement, incl forms, moulds mitred /stopped ends etc complete all as specified and directed.

Material and labour for 15mm thick rendering on brick wall or concrete surface in cement mortar 1:4, surfaces finished even and smooth without using extra cement complete all as specified & directed.

Material and labour for Reinforced concrete drain pipes, 200 mm bore class NP2, laid and jointed in cement mortor (1:1) with collars complete all as specified and directed.

vibha associates

SARSWATI ENTERPRISES

CHANDRA ENGINEERS

SHAKTI CONSTRUCTION CO

m/s gupta construction

vimal construction co

Shivam Construction Co.