REPAIR TO SPALLING MICRO CONCRETE, INTERNAL/EXTERNAL CRACKS FOR REMEDIAL PLASTER WORK, JOINERY, MODULAR KITCHEN AND OTHER B/R WORKS AND REPAIR/MAINT OF LIFT ROOMS VARIOUS HIGH RISED BUILDING AND REPAIR TO GI ROOF SHEET AT NCC OFFICERS MESS AT COLABA

Amount

Anti-termite treatment of soil under existing floors using emulsion @ one litre per hole, 300 mm apart including drilling and plugging 12 mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors, complete all as specified and directed.

Anti-termite treatment of voids in masonry using chemical emulsion one litre per hole, at 300 mm intervals including drilling holes at 45 degree and replugging them with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors, complete all as specified and directed.

Anti-termite treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6 mm dia holes at a downward angle of 45 degree at 150 mm center to center and sealing the same, complete all as specified and directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles including removing debris out side MD land, complete all as specified and directed.

Material and Labour for Brick work with sub class 'B' brick straight or curved on plan exc 6 mtr mean raddius built in CM 1:6, complete all as specified and directed.

Taking down cement plaster on brick/stone or concrete surface including racking out joints, hacking for key, scrubbing down with water to receive plaster, including removing debris/rubbish materials off the site out side MD land, complete all as specified and directed. Note:- upto 4th floor.

M & L for Old unserviceable loose spalled concrete, chiseled from roof ceiling with the help of scrapers, chisel & hammer, cleaning of rust from mild steel rod, applying cement slurry spray 3.00 kg per sqm by paint brush over cleaned surface and thereafter rendering 20-30mm Thick ready mix plaster in multi layer for ceiling on brick wall or concrete surfaces including making groove of appropriate size and finished even & smooth without using extra cement including two coat of OBD / Weathercoat, complete all as specified and directed by Engr-in-Charge.

Material and labour for 15 mm thick ready mix plaster in single layer on fair faces of brick wall or concrete surfaces, finished even and fair, including use of scaffolding, complete all as specified and directed by Engr-in-Charge.

Material and labour for 12 mm thick Ready Mix Plaster in single layer on other than fair faces of concrete surfaces in wall (internal surface) and finished even and smooth, complete all as specified and directed by Engr-in-Charge.

Material and Labour for applying one coat of wall putty 1 mm average thickness on wall surface incl rubbing through authorised applicators, complete all as specified and directed.

Material and Labour for preparation of newly plastered surface of wall and applying two coats of oil emulsion distemper over a coat alkali resistant primer coat through authorised applicators of paint manufacturers only of approved shade, complete all as specified and directed.

Material and Labour for complete removal of existing treatment of old surface of wall and applying two coats of oil emulsion distemper through authorised applicators of paint manufacturers only of approved shade, complete all as specified and directed.

Material and Labour for preparing newly plastered surfaces of walls / ceilings and applying two coats of weather proof acrylic exterior paint (100% Acrylic) Base coat and top coat over a coat of alkali resistent primer including use of scaffoldings, complete all as specified and directed.

Material and Labour for complete removal of existing treatment of old plastered surfaces of walls / ceilings and applying two coats of weather proof acrylic exterior paint (100% Acrylic) Base coat and top coat over a coat of alkali resistent primer including use of scaffoldings, complete all as specified and directed.

Tanking down old cupboard shutteror vanity shutter incl all fitting, complete all as specified and directed.

S & F in repair of 18 mm thick Both Side pre laminated HDHMR Board of any colour, Matt surface finish, grade-I, for frame and shutter with 18 mm wide PVC strips lipping for kitchen cabinets, complete all as specified and directed by Engr-in-charge.

S & F of round stainless steel cabinet/drawers handlers dia of 27mm complete, complete all as specified and directed.

S & F of medium weight, cold rolled mildsteel, SS finish, (Partial overlay/fully overlay of any type) diameter of cup 35mm, Hinge cup depth 11.5mm, self-closing, complete all as specified and directed by Engr-in-Charge. Make : Godrej Kitchen fittings or equivalent in Sleek by Asian Paints or equivalent.

Taking down shutters of any description n.exc 1 sqm each, complete all as specified and directed.

Taking down shutters of any description area exc 1 sqm and n exc 2 sqm each, complete all as specified and directed.

Refixing shutters of any description not exceeding 1 Sqm each in the same opening after taking down, easing and adjusting including refixing builders hardware as required and renewal of unserviceable screws, complete all as specified and directed.

Refixing shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each in the same opening after taking down, easing and adjusting including refixing builders hardware as required and renewal of unserviceable screws, complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and paving not exceeding 15 cm thickness (below or above ground level), complete all as specified and directed.

M&L for PCC type B-1 1:2:4 (20 mm graded stone aggregate) as in levlling course, complete all as specified and directed by Engr in Charge.

M&L for 75mm thick PCC 1:3:6 type C-2 (using 40mm graded stone aggregate) as in plinth protection, complete all as specified and directed by Engr in Charge.

Dismantling, floor hearth or wall tiling inclduing cement mortar bedding and removing rubbish, complete all as specified and directed.

Dismantling, stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar, complete all as specified and directed.

Material and Labour for first and premium quality of vetrified coloured digital tiles 1200 mm x 600 mm x 8 to 10 mm thick, in skirting, dados, risers to steps, etc se and jointed in neat cement slurry, and pointed in coloured cement to match tiles over and including 10mm thick rendering or backing layer in cement mortar 1:4, complete all as specified and directed.

Material and Labour for first and premium quality of vetrified coloured digital tiles size 600 x 1200 x 8 to 10 mm thick polished, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match shed of tiles over and including 15 mm thick screed bed or bedding layer in cement mortar 1:6, complete all as specified and directed.

M&L for machine cut kota stone slab flooring 20-25 mm thick (bull nosing with three antiskid grooved) in one pice over cement screed bese laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing to mirror finish inluding Screed bed or bedding layer of mortar 20 mm thick in (1:6) for laying floor finishes, complete all as specified and directed.

Material and Labour for first and premium quality of PVC vinyl flooring 0.45 mm thick, in floors, design and colour as approved by GE etc. set and jointed with suitable adhesive as per manufacturer insturction, complete all as specified and directed.

Material and Labour for first and premium quality of non skid, joint free ceramic “coloured” tiles of size 300 x 300 x 6-7 mm thick, in floor, shelves etc, set and jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles over and including 15 mm thick screed bed or bedding layer in cement mortar 1:6, complete all as specifed and directed.

Material and Labour for first and premium quality of non skid, ceramic “coloured” tiles of size 300 x 300 x 6-7 mm thick, cut to size in vertical surface, set and jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles over and including 10 mm thick rendering or backing layer in cement mortar 1:4, complete all as specified and directed.

Material and Labour for first and premium quality of Glazed ceramic coloured digital tiles 600 mm x 300 mm x 8 to 9 mm thick, in skirting, dados, risers to steps, etc set and jointed in neat cement slurry, and pointed in coloured cement to match tiles over and including 10mm thick rendering or backing layer in cement mortar 1:4, complete all as specified and directed.

Material and Labour for Vitrified tiles any shade size 600 x 600 x 8-10 mm thick (square/ rectangular) polished, size of each tiles in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match shed of tiles over and including 15mm thick screed bed or bedding layer in cement mortar 1:6, complete all as specified and directed.

Material and Labour for Vitrified tiles any shade size 600 x 600 x 8-10 mm thick cut to size (square/ rectangular) polished, on vertical surface etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match shed of tiles, over and including 10mm thick rendering or backing layer in cement mortar 1:4, complete all as specified and directed.

Material and Labour for HD Ceramic tiles any shade size 600 x 600 x 8-10 mm thick (square/ rectangular) polished, size of each tiles in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match shed of tiles over and including 15mm thick screed bed or bedding layer in cement mortar 1:6, complete all as specified and directed.

Material and Labour for HD Ceramic tiles any shade size 600 x 600 x 8-10 mm thick cut to size (square/ rectangular) polished, on vertical surface etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match shed of tiles, over and including 10mm thick rendering or backing layer in cement mortar 1:4, complete all as specified and directed.

Material and Labour for glazed ceramic exterior wall tiles 6 to 8 mm thick not exceeding 0.36 sqm etc set & jointed in cement and pointed in coloured cement to match the shade of tile over and including 10mm thick rendering or backing layer in cement mortar 1:4, complete all as specified and directed.

Material and Labour for heavy duty outdoor vitrified tiles dark or light shade 12 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match shed of tiles over and including 20 mm thick screed bed or bedding layer in cement mortar 1:6, complete all as specified and directed.

M&L in repair for 8 mm thick laminate wooden flooring, water resistant, termite resistant, polished flooring in a flating glue less click locked & sealed flooring similar to a jigsaw puzzle in this method, the individual planks are locked on the each other by means of the clicking together but do not attach to the sub floor on which it is being installed, complete all as specified and directed.

Supply & Fixed in repair Aluminium composite panel sheet 3mm thick PVCF wooden finished or as approved by GE of brand name 'Euro bound'/"Alstrong"./ "Viva or equivalent" fixed with necessary aluminium tube of size 25mm x 38mm x 1.5mm thick with required cilicon & screw as in ceiling/coloumns and in vertical surface, complete all as specified and directed and approved sample as kept in GE Office.

Material and Labour for Granite stone best quality (of any type) 18 to 20 mm thick machine cut, beded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing over and including 20 mm thick screed bed or bedding layer in cement mortar 1:4, complete all as specified and directed.

Molding (full moulding) of granite slab edges as directed by Engr-in-charge including polishing etc, complete all as specified and directed.

Dismantling wall and ceiling boards or insulation boards, any thickness, any description, including cover fillets, complete all as specified and directed.

Supply and fixing for 12mm thick plywood, grade BWP type BB fixed with brass screws and cups to timber frame work, complete all as specified and directed : sample as approved by GE.

Supply and fixing for 6 mm thick plywood, grade BWP type BB fixed with brass screws and cups to timber frame work, complete all as specified and directed : sample as approved by GE

M & L Decorative laminate 0.9 mm thick type 1 of surface finish, colour and pattern as approved, fixed with approved adhesive as per manufacturer's instructions, complete all as specified and directed by Engr in Charge.

Supply and fixing for 1 to 2 mm thick veneered desinger natural wood grain sheet fixed with adhesive as per manufactrue instruction to plywood work, complete all as specified and directed : sample as approved by GE.

Supply and fixing for Plain fillets of second class hard wood, square or rectangular in section, clean sawn, wrought, secured with nails or brads; sectional area exceeding 6 Sqcm but not exceeding 13 Sqcm, complete all as specified and directed. sample as approved by GE.

Material and Labour for French polishing on new wooden surfaces of any description, width or girth including cleaning and preparing the surface including a coat of wood filler on new works with two or more coats through authorised applicators of paint manufacturers only of approved shade all as specified and directed Make: "Tractor Uno" of Asian Paints / "Jadoo"of Berger Paints / Nerolac Beauty of Nerolac paints as approved by GE, complete all as specified and directed.

Material and Labour for French polishing on old wooden surfaces of any description, width or girth including cleaning and preparing the surface including a coat of wood filler on old works with two or more coats through authorised applicators of paint manufacturers only of approved shade all as specified and directed Make: "Tractor Uno" of Asian Paints / "Jadoo"of Berger Paints / Nerolac Beauty of Nerolac paints as approved by GE, complete all as specified and directed.

Supply & Fixed in repair 0.5 to 1 mm thickness 3D acrylic washable wall papers fixed with adhsive as per manufacture instruction as in ceiling/coloumns and in vertical surface, complete all as specified and directed and approved sample as kept in GE Office.

Supply & Fixed in repair 12 mm thickness fluted WPC indoor panel fixed with necessary aluminium tube of size 25mm x 38mm x 1.5mm thick with required cilicon & screw as in ceiling/coloumns and in vertical surface, complete all as specified and directed and approved sample as kept in GE Office.

Supply and fixing in repair 10 to 12 mm thick Toughned glass as in door shutters, plateform partition including necessary cutting to shape, drilling holes as reqd, jointing cleats, glazing clips, ruber neoprene packing, Stainless steel fittings such as handle 2 nos, 100mm hinge 3 nos, lock including keys 1 set, Stainless steel snap beading & screws, complete all as specified and directed.

S & F frosted film / sunfilm / logo in any type or design and size, complete all as specified and directed.

Providing and fixing Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturers instructions, complete all as specified and directed by Engr in Charge.

Material and Labour for E-board tiles ceiling on GI powder coated channel/Tee/Grid of make (Armstrong or equivalent) frame work with the following specification including cutting holes in brick wall built in cement mortar & making good in cement concrete 1:2:4 type B-0 / Cement mortar 1:3, complete all as specified and directed with following:- (a) Material and Labour for Plugging to wall around the rooms & supplying & fixing GI powder coated angle of make (Armstrong) of size 25 x 25 mm. (b) Supply and fixing 1.60 mm dia GI wire suspenders with adjustable clamps including fixing to ceiling with dash free fasteners. (c) Supply and fixing GI powder coated tee as in main & cross members at 595 mm centre to centre supported suspenders along with adjustable camp to maintain level. (d) Supply and fixing E-board ceiling tilesof size 595 mm x 595 mm x 4 mm thickness, confirming to relevant IS in squares of GI powder coated tee with clips made to shape, shade and pattern of tiles shall be as approved by GE.

S & F in repair Aluminium Mortice lock, 2 lever vertical type, Size 100 mm, complete all as specified and directed.

Supply and fixing for Solid PVC wall Lining consisting of 5 mm thick single side prelam PVC sheet inclusive of solvent cement and fixing at site on PVC frame, complete all as specified and directed, Make : Rajshree/ Navratan or equivalent, sample as approved by GE.

S&F for 5 mm thick PVC sheet fillet of width 35 mm for wall paneling inclusive of fixing on to wall to make PVC frame, complete all as specified and directed.

S & F PVC ceiling wihtout insulation panels with EPS stuck to 1mm Printred PVC sheet suitably placed in false ceiling grid made of Aluminium/G.I./M.S. as per specification and drawing, complete all as specified and directed.

M & L for Anodised aluminium snap grid frame work for false ceiling / POP Ceiling, complete all as specified and directed by Engr - in - Charge.

S&F in repair Stainless steel sink 1mm thick for kitchen, with plug, waste pipe, washers including cantilever cast iron bracket, connecting union over all size 495 mm x 420 mm with bowl size 410 mm x 330 mm x 160 mm, complete all as specified and directed.

Taking up or down steel tubing and connection including cleaning for refixing or removal to store for 15 mm bore, complete all as specified and directed.

Taking up or down steel tubing and connection including cleaning for refixing or removal to store for 20 mm bore, complete all as specified and directed.

Supply & fixing UPVC pipes out side dia 16 mm of pressure rating 10 Kgf/Sqcm, fixed to walls, ceilings or in floors etc, complete all as specified and directed.

Supply & fixing UPVC pipes out side dia 20 mm of pressure rating 10 Kgf/Sqcm, fixed to walls, ceilings or in floors etc, complete all as specified and directed.

S&F tubes medium grade galvanized with all fittings and fixed complete to walls and ceilings or laid in floor for 15 mm bore, complete all as specified and directed.

S&F tubes medium grade galvanized with all fittings and fixed complete to walls and ceilings or laid in floor for 20 mm bore, complete all as specified and directed.

Refixing old steel tubing and connection in new or old portion (walls ceiling, floors etc) for 15 mm bore, complete all as specified and directed.

Refixing old steel tubing and connection in new or old portion (walls ceiling, floors etc) for 20 mm bore, complete all as specified and directed.

M&L for Cutting chases, pinning in making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting exc 10 cm girth but not exc girth 20 cm in brick/stone wall, complete all as specified and as directed by Engr in Charge.

Supply & fixing in repairs vitreous china white wash basin flat back size 550 x 400mm excluding taps, waste, chain, and plug and porcelain stopper but including brackets & cutting for and pinning in end of brackets or erecting stand, complete all as specified and directed.

Supply & fixing in repair for pillar taps cost copper alloy fancy type with capstan head, chromium plated screwed down high pressure with or fly nuts screwed for 15 mm bore iron pipe and fixed, complete all as specified and directed.

Supply & fixing in repair Chromium plated brass angle valve for 15mm bore pipe, fixed, complete all as specified and directed.

Supply & fixing in repair two way angle valve cock chromium plated brass fancy type bore 15mm, complete all as specified and directed.

Supply & fixing in repairs plastic seat cover black/white of pattern W.C including fixing divice and Chromium plated nuts, complete all as specified and directed.

Supply & fixing in repair vitreous china wash down water closet of Pedestal pattern white including making connection to trap and to flushing pipe etc complete and making good to floor, complete all as specified and directed.

Supply & fixing in repair CP brass toilet paper holder, superior quality, complete all as specified and directed.

Supply & fixing in repair CP brass, soap dish, superior quality, complete all as specified and directed.

Supply & fixing Health foucet including PVC pipe 1.50m long with brass nuts for EWC, fixed in repairs, complete all as specified and directed.

Supply & fixing in repair PVC flushing cistern 10 ltr capacity with inlet ball valve float and handle and 32mm bore flush pipe including bracket, complete all as specified and directed.

Supply & fixing in repairs PVC connection 15mm dia and 45cm long with 2 Nos PTMT nuts, complete all as specified and directed.

Supply & fixing in repair sheet glass shelf assembly consinsting of 5.5 mm thick sheet glass shelf 12cm wide with CP bracket guard and railing 60 cm long, complete all as specified and directed.

Material and labour for PCC 1:4:8, type D-2 (using 40 mm graded stone aggregate) as in foundation filling, mass concrete and sunken floor treatments, complete all as specified and directed.

M & L for Water proofing treatment to sunken slab /floors/walls etc and shall be carried out as specified below and as directed. (a) Cleaning the sunken portion of Toilet/bath/WC/Kitchen throughly to remove the laitance, dirt etc and thrown out side the MD land. (b) Form angle fillet of size 50 mm X 50 mm along the junction of wall and floor using polymer modified mortar, Apply one coat of polymer coating on all angle fillets by brush and cover it with 100 mm open glass fibre / geotextile fibre mesh when it is still wet. Apply second coat of the same coating on the angle fillet and allow it to dry completely. Make PIDILITE(Dr fixit Pidicrete URP)/ASIAN(smarcare repair polymer)/FOROC/BASF/SIKA. (c) Sanitary pipe entering through walls and floor shall be sealed with bitumin based seal tape / epoxy bonding agent and gaps to be grouted with non shrink cementitious grout . Nahani traps etc to be fitted securely and gaps around it to be grouted in the same manner. Make : PIDILITE(Dr fixit epoxy bonding agent or bathseal tape )/ AISAN (Smartcare apcorap epoxy bonding agent).

(d) In the remaining area in dry substrate condition brush apply first coat of the acrylic cementitious coating and further apply second coat in perpendicular direcion after 6-8 hours when first coat is dry, and sprinkling quartz sand for shearkey purpose on secon coat in wet condition and allow to dry it completely, Extend the coating up to 1.20 mm above the FFL. Coverage of cementitiou coating to be maintained of min 1.8 kg per sqm for two coats. Make : PIDILITE(Dr fixit fastflex)/ASIAN (ultrablock 2K)/BASF/FOSROCK/SIKA. (e) Sunken portion to be tested for 72 hours for water tightness after only flooring work can be started. Cost for the same shall be deemed to be included in quoted rate. (f) After 2 to 3 days sunken portion must be overlaid with a 50 mm thick concrete screed 1:3:6 type B-0 mixed with integral WPC liquid laid to slope 1:60 towards outer face of wall. Provide 40 mm OD CPVC pipe at the lowest point with 600 mm projection beyond the outer face of the wall, then filled up the sunken portion with lean concrete 1:4:8 type D-2.(Note : lean concrete 1:4:8 paid saperatly). Note:- All the material involved in sunken treatment shall be deemed to be included in quoted rate and only floor area will be measured for the payment purpose.

Material and labour for rendering 10 mm thick in CM (1:4) on fair faces of brickwork or concrete surfaces, with using liquid water proofing compound @ 200 ml per 50 kg bag of cement or as per manufracture's instructions, finished even and smooth without using extra cement, complete all as specified and as directed. Note: WPC shall be measured and paid for seperately under relevant item.

Material and labour for Cement concrete 1:5:10 type E-2 using 40mm graded stone aggregate in foundations, filling and mass concrete including sub base of floors, complete all as specified and as directed.

Supply only integral water proofing compound, complete all as specified and as directed.

S&F in repair vitreous china wash down water closet of "Orissa" pattern size 580 x 440 mm white with integral foot rests including connection to trap and to flushing pipe etc complete and making good to floor, complete all as specified and as directed.

S&F in repair bib taps long body cast copper alloy chromium plated with capstan head, screwed down, screwed for iron pipe or for brass ferrule 15mm bore, complete all as specified and as directed.

S&F in repair bib taps short body cast copper alloy chromium plated with capstan head, screwed down, screwed for iron pipe or for brass ferrule 15mm bore, complete all as specified and as directed.

Demolition/ takingdown existing roof treatment incl PCC pedding by picking sweeping, cleaning and washing down with water to remove dust,durt etc and brushing neat cement slurry @ 3 Kg/Sqm, complete all as specified and as directed.

M&L for plain cement concrete padding 1:2:4 type B-0 of uniform thickness 25mm avg top surface of pain cement concrete padding shall be furnished even and smooth without using extra cement, complete all as specified and as directed.

M&L for 15 mm thick screedi bedding CM 1:4, complete all as specified and as directed.

M&L for applying Bituminious primer on roof surface conforming to IS-3384 of 1986 @ 0.70 Kg/sqm and applying APP based polymeric membrane minimum weighing 3 Kg/sqm and minimum 3 mm thick reinforced with non-woven polyster matt laid on primed surface by torch application complete all as specified with overlap of 100 mm overlap to be thermo fushed by flame, complete all as specified and as directed.

M & L for one coat of aluminium paint at the rate of 100 gms/sqm as per manufacturer instruction over bituminious layer, complete all as specified and as directed.

Taking down door chowkhat with shutter area n-exc 1.5 Sqm each(without taking off shutters from the frame), complete all as specified and as directed.

Taking down chowkhats or frames with shutters exc 1.5 Sqm but not exc 4 Sqm each (without taking off shutters from the frame), complete all as specified and as directed.

S& F in repair Door closer Aluminium extrdued body hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed, complete all as specified and as directed.

S & F Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed in repair, complete all as specified and as directed.

S&F in repair brass classic cylindrical lock with 3 numbers of keys and 60 mm backset, complete all as specified and as directed.

S&F in repair brass pad Lock, 6 lever of size 100 mm suitable for Aluminum doors, complete all as specified and as directed.

S&F for 2nd class hardwood plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue, pinned at joints, complete all as specified and as directed.

M&L fixed in repair for mild steel framed work such as grill, gates, guard bar, framed with welding using angle iron, square bars and round bars section etc including cutting, welding, revetting, complete all as specified and as directed.

S&F factory made 30 mm thick flush shutter solid core construction with block board core & plywood face panels commercial type on both sides incl 5mm thick teakwood leaping alround, complete all as specified and as directed.

S&F 2nd class hardwood factory made door, 35 mm thick, glazed and skeleton shutters, open rebated and prepated to receive glass gauze etc (with sash bars) edges of framing plain, chamfered or rounded materials and revated sash bars any number, edges of framing plain chemfered or rounded fitted with cut and mitred beads for securing glass in door etc or provided with styles and rails as specified in SSR part 1 section 8, clause 8.20 (a), complete all as specified and as directed.

S&F for 2nd class hardwood glazed and skeleton window shutter 30mm thick, divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers, to receive glass, gauze, etcor provided with styles and rails as specified in SSR part 1 section 8, clause 8.20 (b), complete all as specified and as directed.

Cutting holes in brick walls built in cement or cement lime mortar for inserting hold fasts, etc and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B-1 cutting exceeding half brick but not exceeding one brick, complete all as specified and as directed.

S&F mild steel bends strips, hold fast or small articles of FI or angle, complete all as specified and as directed.

S&F for galvanised MS Wire cloth of 0.56 mm nominal dia of wire and average width of aparture 1.18 mm fixed with tinned tack for galvanized wire staple, complete all as specified and as directed.

S&F in repair for galvanised MS Wire cloth of 0.56 mm nominal dia of wire and average width of aparture 1.18 mm fixed with tinned tack for galvanized wire staple incl fixed, complete all as specified and as directed.

Hacking out old broken glass (any thickness, size quality or description) from wooden frames or stone, concrete or brick surrounds glazed with putty or fixed with beads, complete all as specified and as directed.

M&L for 3mm thick sheet glass ordinary quality and glazing with oil putty in square n-exc 0.5 sqm in each pane, complete all as specified and as directed.

M&L for 3mm thick sheet glass Figured glass, pin head type and glazing with oil putty in square n-exc 0.5 sqm in each pane, complete all as specified and as directed.

M&L for 5.5 mm thick sheet glass ordinary quality and glazing with oil putty in square exc 0.5 sqm in each pane, complete all as specified and as directed.

S&F 300mm long aluminnium alloy sliding door bolts, plate type, stove enameled black, with bright bolt not less than 12mm dia with and incl minimum of 6 bolts and nuts, four on bolt plate and two on staple, complete all as specified and as directed.

S&F MS butt hinges cold rolled meium weight of size 100mm etc, complete all as specified and as directed.

S&F MS butt hinges cold rolled meium weight of size 75 mm etc, complete all as specified and as directed.

M&L for Mild steel plain black sheet 1.25 mm thick in hearths; covering to door shutters; ducts, etc, cut to size, edges beaded if directed, holes punched; including round headed screws, clout nails or rivets, fixed to wood or steel members with plain 40mm lap joints or welded/riveted seams including bending, turning up, mitred angles, stopped ends, etc as required, complete all as specified and as directed.

M&L for applying two coats of synthetic enamel paint over a coat of red oxide primer on new or previously untreated steel surfaces not exc 10 cm width or girth including preparation of surface, complete all as specified and as directed.

M&L for preparing wooden new surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and as directed.

M&L for preparing wooden old surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint, complete all as specified and as directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube in opening as per specification and shown in drg in SSR Part -II 2010, complete all as specified and as directed.

S&F factory made solid panel PVC door shutter 30mm thick consisting of frame made out of MS frame shall be covered with heat moulded plain cover PVC C channel having a PVC sheet strip of 20mm with struck in side with solvent cement for styles and plain colour PVC sheet for top rail lock rail and bottom rail and either side as gap inserted for top rail and bottom rail panelling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the styles and rails with suitable PVC sheet beading sheet and jointed together with solvent cement in frame at site as per specification and shown in drg in SSR Part -II 2010, complete all as specified and as directed.

S&F 200 mm long aluminium anodized barrel tower bolt of extruded section, complete all as specified and as directed.

S&F 100 mm long Aluminium butt hinges of extruded aluminium alloy with galvanized mild steel hinge, pin anodized, complete all as specified and as directed.

S&F 150 mm long aluminium alloy handle cast type anodized, complete all as specified and as directed.

S & F powder coated aluminium sections for doors, windows, ventilators, door partition including fabrication of frame shutters and fixing with necessary lugs, cleats, rollers, handles, locking arrangement etc. including all accessories such as glazings clips, and rubber beadings for fixing glass panes in frame, complete all as specified and as directed. Note : (i) Glass panes will be measured & paid separately . (ii)The quoted rate shall be inclusive of cost of rubber beading however it will be not be weighed and not paid separately. (iii) All other minor details including cost of locking arrangement shall be included in the quoted rate. (iv) Windows all around will be sealed with silicon sealant.

S & F aluminium grill of 5mm thick of design and opening as approved by engr in charge fixed with aluminium channel 'F ' 20mmx15mm fixed in position with screw, complete all as specified and as directed.

S&F in repair 20 mm dia decorative type C chromium plated anodised aluminium alloy with fixing brackts and all other connected works, complete all as specified and directed.

Supply & Fixed in repair anti rusting stainless cloth drying hanger made of 16 mm dia hollow anodisied aluminium rod, 6 feet x 4 rods set for heavy duty including fixing on ceiling with metal roof clamps, complete all as specified and directed.

S&F in repair of stainless steel kitchen plate rack made out of 0.63mm thick stainless steel sheet of size 750x600mm including screws including taking down, complete all as specified and directed by Engr-in-Charge.

S&F in repair 18 mm thick marine plyboard laminated of any coulour with high glossy acrylic sheet of 3 mm thick grade-1 as per IS 14587 for frame and shutter for kitchen cabinet, complete all as specified and as directed.

S & F in repair of medium weight, cold rolled mildsteel, SS finish, (Partial overlay/fully overlay of any type) diameter of cup 35mm, Hinge cup depth 11.5mm, self-closing, complete all as specified and directed by Engr-in-Charge. Make : Godrej Kitchen fittings or equivalent in Sleek by Asian Paints or equivalent.

S & F of stainless steel 304 electro-polished for corrosion resistance modular thali holder / basket having size of 42 x 58.5 x 20 cm including telescopic drawer channel having weighing capacity of 6 kg, including taking down, complete all as specified and directed. Make : Cat Part No 5704 Godrej Kitchen fittings or equivalent in Sleek by Asian Paints or equivalent.

S & F of stainless steel 304 electro-polished for corrosion resistancemodular cup & saucer holder / basket size of 52 x 53.5 x 10 cm with telescopic drawer channel having weighing capacity of 4kg, including taking down, complete all as specified and directed. Make : Cat Part No 5837 Godrej Kitchen fittings or equivalent in Sleek by Asian Paints or equivalent

S & F of round stainless steel cabinet/drawers handlers dia of 27mm, including taking down, complete all as specified and directed. Make:- Godrej Kitchen fittings and Sleek by Asian Paints or equivalent.

S&F stainlesss steel modular perforated cutlery basket SS 304 size size of 52x48.5x10 cm with telescopic drawer channel having weighing capacity of 6 kg, including taking down, complete all as specified and directed. Make Godrej kitchen appliances or equivalent.

S&F in repair grain trolley SS 304 with telescopic drawer channel having weighing capacity of 6 kg, complete all as specified and directed.

S&F of stainless steel hanging spice rack having three three shelf spaces length of 500 mm, including taking down, complete all as specified and directed. Make Godrej kitchen appliances or equivalent.

S&F for butt hinges cast brass with mild hingespin, bright polished and fixed type B-11 of size 100mm etc, complete all as specified and directed.

S&F for 150 mm extruded brass handles, fabricated type polished, complete all as specified and directed.

S&F for brass barrel tower bolts of extruded section 200 mm long, complete all as specified and directed.

S&F for 300mm long brass sliding door bolts with sand or die-cast brass hasp staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed, complete all as specified and directed.

S&F for brass classic cylindrical lock with 3 numbers of keys and 60 mm backset, complete all as specified and directed.

Supplying and fixing factory made single extruded WPC (Wood Polymer Composite) solid door Frames/Chowkhat comprising of 65 mm x 125 mm size applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length, complete all as specified and directed.

Supplying and fixing factory made 28-30mm thick single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size modulus of elasticity 850 N/mm” and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and directed.

Supply & Fixed in repair PVC tensile fabric structure with PVDF (polyvinyl-idene-fluoride) Coating with all necessary fixtures, of any size and shapefor making canopies, shade etc fixed with mild steel structural frame work, weight of the fabric is considered, with fabrics ranging from 900 GSM to 1200 GSM, complete all as specified and directed. Make: Mehler / Sieon / Haytes / Farrari or equivalent as approved GE. Note :- (i) The shape / Design of the shads will be as approved By GE.

Supply and Installation of Spring Polyester Roller Blinds spring component easy for useing, once touch up the second pull stop, can stay any positions you want.Spring strength can be adjusted by a key with hanging rails, mounting bracket, spring , weight including all accessories and required hard ware in different size of window indifferent rooms, complete all as specified and directed and Make and sample approved by GE.

Dismantling asbestos cement (corrugated, semi corrugated etc) sheets in roof coverings including ridges, complete all as specified and directed.

M&L for Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified and directed.

Demolition and breaking up drain pipes (SGSW, AC or RCC, CI ) of internal dia 75/110 mm, set in cement mortar, complete all as specified and directed.

S&F for PVC (SWR) pipes, single socketed, in any length with rubber ring joints, fixed to walls, 110mm bore, complete all as specified and directed.

S&F for PVC (SWR) pipes, single socketed, in any length with rubber ring joints, fixed to walls, 75 mm bore, complete all as specified and directed.

S&F for PVC (SWR) bends any radius, 110 mm bore, complete all as specified and directed.

S&F for PVC (SWR) bends any radius, 75 mm bore, complete all as specified and directed.

S&F for PVC (SWR) branch piece, single (single Y) equal or unequal radius, 110 mm bore, complete all as specified and directed.

S&F for PVC (SWR) branch piece, single (single Y) equal or unequal radius, 75 mm bore, complete all as specified and directed.

S&F for PVC (SWR) branch piece, single (single T) equal or unequal radius, 110 mm bore, complete all as specified and directed.

S&F for PVC (SWR) branch piece, single (single T) equal or unequal radius, 75 mm bore, complete all as specified and directed.

S&F for PVC (SWR) reducers, 110 mm bore, complete all as specified and directed.

S&F for PVC (SWR) reducers, 75 mm bore, complete all as specified and directed.

Taking down cement plaster on brick/stone or concrete surface including racking out joints, hacking for key, scrubbing down with water to receive plaster, including removing debris/rubbish materials off the site out side MD land, complete all as specified and directed. Note:- upto 5th floor to 8th floor.

Taking down cement plaster on brick/stone or concrete surface including racking out joints, hacking for key, scrubbing down with water to receive plaster, including removing debris/rubbish materials off the site out side MD land, complete all as specified and directed. Note:- upto 9th floor to 12th floor.

Taking down cement plaster on brick/stone or concrete surface including racking out joints, hacking for key, scrubbing down with water to receive plaster, including removing debris/rubbish materials off the site out side MD land, complete all as specified and directed. Note:- upto 12th floor to 16th floor.

M&L for rendering 15mm thick in CM (1:4) mixed with in liquid water proofing compound on fair faces of brick wall or concrete surfaces, finished even and fair, complete all as speciifed and directed. Note:- WPC measured and paid seperately Note :- Upto 4th floor

Ditto as per item No. 170 but 5th to 8th floor.

Ditto as per item No. 170 but 9th to 12th floor.

Ditto as per item No. 170 but 13th to 16th floor.

M & L for preparing new surfaces of walls / ceilings by scrapping / rubbing and applying two coats of Elastomeric and resilient acrylic polymers and reinforcing synthetic fibers water proofing coating over a coat of alkali resistent primer through authorized applicator only including use of scaffoldings from Ground floor upto 04 storeys bldgs, complete all as specified and directed.

All as per item No. 174 above but 5th to 8th floor.

All as per item No. 174 above but 9th to 12th floor.

All as per item No. 174 above but 13th to 16th floor.

Demolition of concrete of any description and in any position not otherwise specifically provided and including removing debris out side MoD land, complete all as specified and directed.

Demolition of concrete (reinforced) of any description and in any position not otherwise specifically provided and including removing debris out side MoD land, complete all as specified and directed.

M&L RCC M-30 (20 mm graded stone aggregates) as in foundations, footings incl necessary formwork as required, complete all as specified and directed.

M & L for mild steel TMT bars any dia in stirrups, spaces and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and as directed.

M & L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips and including welding has to be done with minimum 20 cm over lap for new and old of any height, complete all as specified and as directed.

Use and waste for fromwork to faces of smooth finished walls, retaining walls, abutement, parapets, and staircase railings and similar works incl attached pilasters, buttressess etc; vertical or to batter incl bolting, strutting, propping etc so as to withstand a pressure of 0.1 MPa incl removal of form work, complete all as specified and as directed.

Providing and placing in position micro-concrete, grade M-30, which shall be cement based prepacked single component, chloride free, non-shrink, free flow, self compacting, ready to use after mixing water in specified proportion, obtained from Fosroc / SIKA / BASF/ Dr Fixit, thickness of section upto 100 mm complete including form works as required all as specified and as directed by the Engineer in charge (Payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding/ tapping with a blunt metal instrument), complete all as specified and as directed.

Use and waste for Formwork to edges of concrete flats, breaks in floors, openings in concrete walls, floors and roofs and sides of RCC/PCC bands in walls, horizontal or sloping, and similar work all exceeding 20cm wide, complete all as specified and as directed.

Applying three coat URP water proofing chemicals for water proofing coating mix URP- cement in the ratio 1:1.5 by volume on new plastered surface as per manufature instruction for sunken portion, complete all as specified and directed by Engr-in-Charge. Make : Dr Fixit -301 or equivalent of Asian paint / Fosroc/ sika

M&L for minor cleaning work, removal of existing roof treatment, loose concrete and filling cracks with polymer modified mortar using SmartCare RP or Epoxy Mortar and supplying and applying High performance hybrid polyurea elastomeric waterproofing coating cold applied of spray / brush applied, SmartCare Ultron liquid membrane with an elongation of 600% and tensile strength of 12.6 N/mm2 as per ASTM D 2370, crack bridging ability of 3mm as per ASTM C1305, shore A Hardness of min. 75 as per ASTM D 2240. The system includes final base preparation, epoxy primer application and applying SmartCare Ultron or approved equivalent in two coats at 1.5 kg per Sqm etc, complete as per Manufacturer specifications. Supplying and applying High performance hybrid polyurea elastomeric waterproofing coating cold applied of spray / brush applied, SmartCare Ultron liquid membrane with an elongation of 600% and tensile strength of 12.6 N/mm2 as per ASTM D 2370, crack bridging ability of 3mm as per ASTM C1305, shore A Hardness of min. 75 as per ASTM D 2240. The system includes final base preparation, epoxy primer application and applying SmartCare Ultron or approved equivalent in two coats at 1.5 kg per Sqm etc, complete as per Manufacturer specifications over and including padding of ready mixed micro cement concrete Type B-1, 1:2:4 , 35 mm average thick concrete on RCC roof surfaces and all other similar works, complete all as specified and directed Make:SmartCare Ultron Hybrid Polyurea/ Dr fixit flexi PU

M&L APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application, complete all as specified and as directed.

M&L Priming surfaces and applying normal treatment (for moderate conditions) using glass fibre base bitumen felt, grade 2, complete all as specified and as directed.

Material and Labour for full Vitrified ultra polished tiles dark or light shade 600 x 1200 x 10-12 mm cut to size (square/ rectangular) polished, on vertical surface etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match shed of tiles, over and including 10mm thick rendering or backing layer in cement mortar 1:4, complete all as specified and directed.

S&F powder coated aluminium frame of any colour (minimum thickness of powder coating 50 micron) for doors/windows/ ventilators with one or more rebates including joining cleat for fixing etc, complete all as specified and directed.

S&F in repair stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with stainless steel wire, staples, complete all as specified and directed.

M&L Rolled mild steel framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing, complete all as specified and directed.

Dismantling of wrought iron or mild steel work of any description not otherwise provided for, complete all as specified and directed.

S&F for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., complete all as specified and directed.

S & F for Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240, complete all as specified and directed.

S & F MS plate (CHEQUERED) 5mm and over as in manhole cover fixed to angle iron frame with three Nos of hinges and 150 mm handle, complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet/semi corrugated 0.50 mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws, including dismantling old roof sheets any type, complete all as specified and directed by Engr-in-Charge.

S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, eaves etc fixed with self tapping screws, including dismantling old roof sheets any type, complete all as specified and directed by Engr-in-Charge.

Material and labour in repair to replace old decayed timber (including piecing, scarifying, etc of old and new timber if required) second class hard wood clean sawn in scantlings timber framed and fixed in any position and description including scafoldings of any hieght, complete all as specified and directed.

M&L for cement concrete type C-0 1:3:6 (12.50 mm graded aggregate) in concrete work or for fixing of roof members/angle etc, complete all as specified and directed.

M&L for rendering 15mm thick in CM (1:6) mixed with in liquid water proofing compound on brick work/ concrete work or in chajjas/parapet walls surfaces etc., finished even and smooth without using extra cement, complete all as speciifed and directed. Note: WPC shall be measured and paid seperately.

Material and Labour for preparation of newly plastered surface of wall and applying two coats of oil bound distemper over a coat alkali resistant primer coat over 1mm thick wall care putty, complete all as specified and directed.

Material and Labour for preparation of old plastered surface of wall, cornices and applying one coat of oil bound distemper, complete all as specified and directed.

Taking down carefully copper/aluminum point wiring (light, fan, socket or power) complete encluding all fittings and fixtures such as switches, pendant, lamp holder, regulators, switch socket outlet, bulk head fittings, tube light fittings, etc. and removing unserviceable materials from site of work and making good disturbed surfaces of walls, floors with cement mortar and white/colour wash to match with existing surfaces etc, complete all as specified and directed.

Taking down carefully copper/aluminum submain/ copper flexible cable wiring, complete all as specified and directed.

S&F in repairs non-metallic PVC casing capping of size 25X12mm, complete all as specified and directed.

M&L for Point wiring (concealed type) with 1.5 sqmm, PVC insulated unsheathed (FRLSH), 1100 volts grade, multi-stranded copper conductor, in and including rigid non-metallic PVC heavy duty conduit (ISI mark), 19/ 20 mm dia suitable size including cutting chases for conduits, sinking for boxes for concealed conduit wiring with all fittings and accessories including with and fix concealed 1.2mm thick pressed steel sunken box along with cover plate and frame, suitable for fixing moduler switch/ socket and unsheathed (FRLSH) single core multi-stranded copper conductor cable of size 1.5 sqmm green in colour/paint as earth continuity conductor connected to common earth dolly and making good to the disturbed surfaces to match the existing surfaces complete (fill up cement in gaps, finishing with putty and apply two coats of paint, match with existing colour/paint in disturbed surface area), as per IS specification and as specified in SSR Part-I complete for one light point / bell point/ Ex Fan point / wall fan point controlled by one modular switch, 1 way 6/10 amps, 1 module, complete all as specified and directed.

All as per serial No. 208 here-in before but for one bell point controlled by one switch.

All as per serial No. 208 here-in before but for One 3 pin socket point 5 Amps on independent board.

All as per serial No. 208 here-in before but for One 3 pin socket point 5 Amps on same board.

All as per srl item No. 4 here-in-before but for one socket point 15 Amp with 2.5 sqmm PVC unsheathed FRLS wire along with 2.5 sqmm green colour wire as earth contuinity conductor connected to common earth dolly.

All as per srl item No. 4 here-in-before but for one socket point 15 Amp with 4 sqmm PVC unsheathed FRLS wire along with 4 sqmm green colour wire as earth contuinity conductor connected to common earth dolly.

S&F in repairs Moduler Switch single pole, one way 6/10 Amp with all fittings and accessories including with and fix concealed 1.2 mm thick pressed steel sunken box along with cover plate and frame, complete all as specified and directed.

S&F in repairs Moduler Switch single pole, one way 16 Amp with all fittings and accessories including with and fix concealed 1.2 mm thick pressed steel sunken box along with cover plate and frame, complete all as specified and directed.

S&F in repairs Moduler socket 2/3 pin 6 Amp with all fittings and accessories including with and fix concealed 1.2 mm thick pressed steel sunken box along with cover plate and frame, complete all as specified and directed.

S&F in repairs Moduler socket 6/16 A 2/3 pin with all fittings and accessories including with and fix concealed 1.2 mm thick pressed steel sunken box along with cover plate and frame, complete all as specified and directed.

S&F in repairs Moduler stepped type electronic fan regulator 450 watt flush type, two module with all fittings and accessories including with and fix concealed 1.2 mm thick pressed steel sunken box along with cover plate and frame, complete all as specified and directed.

S&F in repairs Moduler bell push, 2 modue, 10 Amp with all fittings and accessories including with and fix concealed 1.2 mm thick pressed steel sunken box along with cover plate and frame, complete all as specified and directed.

S&F in repairs Metal AC/ Geyser Box with Socket and 20 Amp SP mini MCB in plastic box enclosure along with cover plate and top, complete all as specified and directed.

S&F in repairs bell ding dong, AC, 230 volts, single pole, complete all as specified and directed.

S&F in repairs ceiling rose surface bakelite 65x50mm, 3 terminal, complete all as specified and directed.

M&L Sub main wiring with two runs of 6 sqmm stranded copper conductor PVC unsheathed FRLSH wire along with 6 sqmm green colour wire as earth contuinity conductor connected to common earth dolly including PVC FR heavy duty conduit of adequate size (not less than 44 mm dia) for housing the wires from panel / Main DB to house SPN DB, including taking down/out, complete all as specified & as directed by Engr-in-Charge. Note: (i) Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB. (ii) Mode of measurement two runs of 6 sqmm cable and one run of 6 sqmm cable with PVC conduite shall be measured as one length.

M&L for Sub main wiring with two run of 4 sqmm stranded copper conductor PVC unseathed FRLSH wire along with 4 sqmm green colour wire as earth contuinity conductor connected to common earth dolly including PVC FR heavy duty conduite of adequate size (not less than 32 mm dia) for housing the wires for from Internal DB to DB, complete all as specified & as directed by Engr-in-Charge. Note: (i) Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB. (ii) Mode of measurement two runs of 4 sqmm cable and one run of 4 sqmm cable with PVC conduite shall be measured as one length.

S&F in repairs 20 watt LED white /warm white 4 feet long fixed on PVC square for mounting the fittings and electrically conncected with suitable size of PVC insulated multistranded copper flexible cable from ceiling rose to light fitting (connector block of lamp fitting), complete all as specified and directed.

S&F in repairs surface mounted 9/10 watts white /warm white LED tube light fitting and electrically conncected with suitable size of PVC insulated multistranded copper flexible cable from ceiling rose to light fitting, complete all as specified and directed.

S&F in repairs LED Mirror light fittngs 2 feet 10W extruded polycarbonate, golden type electrically conncected with suitable size of PVC insulated multistranded copper flexible cable from ceiling rose to light fitting, complete all as specified and directed.

S&F in repairs exhaust fan plastic body having 40 watt power double ball of bearing high speed of sweep size 250 mm, inbuilt bird gaurd with louvre and air delivery more than 900 CMH with nuts bolts, fastners including connecting with PVC insulated and PVC sheathed copper flexible cable and necessary fixing arrangement, complete all as specified and directed.

S&F in repairs decorative wall mounting fitting, working on 240 volts, 50 hz, fittings comprising with stainless steel finish fixture including with opal glass with nickel finish base diffuser and with LED bulb E27 of capacity 7watt, complete all as specified and directed.

S&F in repairs LED 18/22 Watt 3000 K/6000k, Slim raccess mounted Circular LED panel bright white/ warm white with premium diffuser to ensure glare free & even light distribution in area, with integrated electronic driver of same make connecting with PVC insulated and PVC sheathed copper flexible cable and necessary fixing arrangement, complete all as specified and directed.

S&F in repairs LED 36 Watt 3000 K, Slim raccess mounted LED panel 2x2 with premium diffuser to ensure glare free & even light distribution, with integrated electronic driver of same make connecting with PVC insulated and PVC sheathed copper flexible cable and necessary fixing arrangement, complete all as specified and directed.

S&F in repairs sheet metal enclosures double door, for DBs when MCBs to be used 240 volts 8 way with 200 Amps rated bus bar for single pole and neutral fixed on wall by cutting chasing and making good to the disturbed surfaced board in and including copper lugs/thimbles duly crimped for connection, complete all as specified and directed.

S&F in repairs sheet metal enclosures double door, for DBs when MCBs to be used 240 volts 12 way with 200 Amps rated bus bar single pole and neutral fixed on wall by cutting chasing and making good to the disturbed surfaced board in and including copper lugs/thimbles duly crimped for connection, complete all as specified and directed.

S&F in repairs MCB SP 240 volt, 16 to 40 Amps, C series, complete all as specified and directed. Note: Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB.

S&F in repairs MCB SPN 240 volt, 40 to 63 Amps, C series, complete all as specified and directed. Note: Thimble/lugs of rating of MCB should be used with wire for fixing in the MCB.

Transportation and fixing or refixing of Ceiling Fan/exhaust fan of any size with hooks, nuts bolts, Down rod, fastners including connecting with PVC insulated and PVC sheathed copper flexible cable and necessary fixing arrangement, complete all as specified and directed including deposition old fan safely in MES store.

Bright Construction Co (BID ID -3489718)

GANGAJAL (BID ID -3480661)