IMPROVEMENT TO CERTAIN OMQ BLOCKS (PH-1) AT 13 BRD AF STN PALAM UNDER GE (P) AF GURGAON

Amount

Dismantling of roof tiles/brick tiles any thickness and any size complete all as specified and as directed.

M&L for 15 mm thick cement plastering in cement mortar 1:4 on brick/concrete surfaces of roof and parapet, mixed with water proofing compound as per manufacturer instructions, finished even and smooth without using extra cement (Including 4 Story building) complete all as specified and as directed. Note :- Water proofing compound shall be measured & paid separately under respective item.

Supply only liquid water proofing compound of approved make

Cleaning top surfaces by brooming, wire brushing, removing grass, raking out joints to receive plaster and removing debris, grass etc outside the defence land complete all as specified and directed. Note :- (i) Plaster shall be measured and separately under appropriate item of Sch ‘A’. (ii)Rate of this item is inclusive of diconnect fitment at water tank or solar heater etc and refixing in the same position after compeleting of roof treatment.

M&L for applying 3.00mm thick APP based polymer membrane by torch application for sealing joint over 85/25 industrial bituminous coat @ 1.20Kg/Sqm over bituminous primer @ 0.30 Ltr/Sqm on newly plastered clean and dry roof surface complete all as per manufacturer instructions, specified & directed by Engr-in-charge.

M&L for washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 white cement: 1/2 coarse sand: 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete all as specified and as directed. Note:-Payment for providing grooves shall be made separately under respective item.

M&L for forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and direction of the Engineer-in-charge.

Taking down cement plaster from wall and ceiling of any description from brick/concrete surfaces including raking out Joints, hacking for Key, scrubbing down with water, etc., and removing same from the Site(s), complete all as specified and as directed. Note :- Rate included for four storey building including skafolding and all safety measures)

M&L for 15mm thick rendering in cement mortar 1:4 on fair faces of brick or concrete surfaces including finishing even and smooth without extra cement all as specified and as directed.

M&L for 5mm thick rendering in cement mortar 1:3 on concrete/gunniting surface as in ceiling finished even and smooth w/o using extra complete all as specified and directed.

M&L for 15mm thick rendering on brick or concrete surfaces in internal surfaces in cement mortar 1:6, finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of newely plastered ceiling surface and applying three coats of white wash complete and all as specified and as directed

M&L for preparing new plastered on walls including cornices by brooming down or steel wire brusing, scraping down, smoke spots and M&L for applying two coat of exterior emulsion paint 100% acrylic of approved colour and shade by GE complete over a coat of primer and over 2 to 3 mm thick birla putty punning complete all as specified and directed. Make-Asian (Apex Ultima) paints/Berger (Whether coat long life) including necessary scaffolding upto 4th floor.

M&L for preparing new decorated surfaces plastered on walls including cornices plasters by brooming down or steel wire brusing, scraping down, smoke spots and applying two coat of oil emulsion over a coat of primer complete and over 2 to 3 mm thick birla putty punning and to be applied by authorized applicator of manufacture's as approved by GE complete all as specified and as directed including necessary scaffolding upto 4th floor. Make: Asian Paint /Berger paints

Excavation in post holes not exc 0.5 Cum, getting out, returning filling in layers n exc 25cm in thickness and removing surplus soil to a distance n exc 50 surface in hard/dense soil complete all as specified and as directed.

M & L for PCC 1:3:6 Type C2 (using 40mm Graded stone aggregate) as in for fixing posts, bed plates, anchorage blocks, corbels, brackets, including necessary form work etc. complete all as specified and as directed.

M&L fore Mild steel angle iron Fe-290 Gde E-165 as in posts, struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc., flat iron fillets (for securing wire mesh and wire any type) ncluding all necessary drilling, bolting or riveting and embedding in concrete complete all as specified and as directed.

Material and Labour for MS bars 10mm dia as in stiffener to chain link fencing incl necessary cutings,bending,etc. confirming to Fe 250 and over cut to length,bent to shape required inclundind cracking,bending,spirally hooping with ms(annealed) with bolts complete all as specified and as directed.

S&F chain link fencing MS galvanised, 100x100mm mesh or cases with of 3.15 mm dia mild steel Galvanised wire, lapped straining and binding with incl mild steel wire (annealed) not less than 0.9mm dia including provision of binding wire complete all as specified and as directed

Supply and fixing of mild steel screw bolt (machine made) of 11 to 15 mm neak diameter with hexaganal or squre head and bun end.screw other or screw both end,each screw and to be fited with wisher and one hexaganon or squre nut.exc.5cm and n.exc. 10 cm long complete all as specified and as directed.

M&L Mild steel work as column etc. for frame work to support rafter/purlin for roof including cutting welding and all necessary drilling, bolting or riveting etc. complete conforming to Fe 410 W all as specified and as directed.

S&F for Mild steel rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates complete all as specified and as directed.

M&L for pre painted galvalume aluminium zinc coated GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed in repair with self tapping J hooks including dismantling of existing sheet in any position complete all as specified and directed.

S & F mild steel work conforming to Fe-310-0 or 410-0 as in railing, bands, hold fasts, wall ties, wind ties straps, supports and stay for,steps,laddar. rain water pipes,clamps and similar articles complete all as specified and directed.

S & F framed work such as grills, gratings, with ornamental & intricate design for windows, ladder etc., with ends of bar shoulder or riveted, or forged into spikes; framed guard bars, incl hinges, framed balusters, walk ways; railings & similar work conforming to Fe 290 GDE -E-165 complete all as specified and as directed.

S&F framed bracket of angles or box section cut to shape, drilled, including bending & welding, as necessary, gusset plates, riveting, etc. for window sun Shade, n exc 10kg each brackets, conforming to Fe 290 GDE -E-165 complete all as specified and as directed.

M&L for applying two coats synthetic enamel paint over a coat of red oxide zinc chromate primer including preparation of new steel/iron surfaces exc 10cm in width or girth complete all as specified and as directed.

Dismantling of wall and ceiling boards (Fibre, pulp, insulation, wooden etc.) or insulation board / slabs any thickness incl cover fillets complete all as specified and as directed.

S&F 18mm thick plywood (12 ply) fixed with 0.9mm thick decorated laminated both side pasted with adhesive as in kitchen cupboard shutter and shelves etc. fixed with screws, complete including necessary hinges, hucks and handle screw and fixing items for wall/ floor and cup boards etc complete all as specified and as directed.

S&F for Kitchen cabinet work including Cub board hinges, racks, 12mm teak plywood with 0.9mm thick both sides decorated laminated cub board Shutters, inclunding Decorated SS handles, Cabinet SS hinges, S/Steel racks 304 or S/steel row with 304 quality stainless steel as cabinats for holding kitchen items including sliding channel 60cm long etc. with necessary fixing arrangements, Screws etc all fixed in repairs for 60cm depth complete all as specified and as directed.

Repairing and strengthning of existing RCC structure by re-baring by drilling holes and fixing nozzle if required in existing concrete/brick work as in column, beams, slabs and chajja etc in any position and any description size of hole 14mm, 16mm & 22mm suitable for dowels of size 10mm, 12mm & 16mm respectively (minimum depth 140mm for 10mm & 12 mm dia bars and 180mm for 16mm dia bar, cleaning the surface properly with blow out pump & round brushes and fixing of dowel bars with epoxy resin (resin+hardner). Make: Sika/ Fosroc or concressive 1450 of BASF complete all as specified and directed by Engr-in-charge. Note:- (i) Adequate lap length shall be provided as per IS-456-2000.(ii) Reinforced TMT bars where incorporated in work will be paid under seperate items. (iii) The work shall be carried out upto four storied building with necessary scaffolding.

M&L for fixing 2mm dia wire and 25x50mm MS welded mesh fixing in defective RCC surface before guniting by using pressure guniting machine and finishing the top surface even and fair complete all as specified and as directed.

Demolition of brick work masonry, built in cement mortar of any description and rubbish off the premises complete all as specified and as directed.

M&L brick work with sub class 'B' bricks straight or curved on plan exceeding 6m mean radius built in cement mortar 1:4 complete all as specified and directed.

M&L plain cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) as in coping, benching, bed block, coving, window cills etc complete all as specified and directed.

Removal of debris/malwa to a distance exc 250m but n exc 500m and depositing whete directed by Engr-in-charge.

Demolition of Cement Concrete (un-reinforced) of any description, not exc. 150mm thickness (above or below Ground Level) and removing the same from Site(s), complete all as specified and as directed.

Dismaintling of Stone slabs and tiles of any description or thickness in floor or wall, aprons and laid badded and pointed in any mortar. Etc complete all as specified and as directed.

M&L for 25mm thick PCC 1:2:4 Type B0 (using 12.5mm Graded Stone Aggregate) as in sub floors, etc., to receive floor topping, complete all as specified and as directed.

M&L Non–Skid Ceramic Coloured Tiles, size 300x300x7 or 400X400X7 to 10mm in size, laid on floor,over and including 15mm thick screed bed in cement mortar 1:4 Laid and Jointed in neat cement slurry and pointed in white wement with pigment to match the shade of the tile complete all as specified and as directed.

M&L for Glazed Ceramic Coloured Tiles, 300X450X7mm to 8mm thick, set on Vertical Surfaces such as Skirting, Dado, etc,over and including 10mm thick rendering in cement mortar 1:3 Set and Jointed in Neat Cement Slurry and Pointed in White Cement with pigment to match the shade of the Tiles, complete all as specified and as directed.

S & F vitrified tiles tiles light shade 10mm thick (square/rectangular) polished, area of each tile n.exc. 0.36 sqm, in floor etc.,set and jointed in neat cement slurry over and including 15mm thick screed bed in cement mortar 1:4 and pointed in white cement with pigment to match the shade of floor fineshes complete all as specified and as directed.

M&L Non–Skid ceramic joint free Coloured Tiles, size 600x600x10mm in size, Laid on Floor, Laid and Jointed in Neat Cement Slurry and Pointed in Coloured Cement to match the shade of the Tiles,including Screed Bed or Bedding Layer 15mm thick as in Floor in Cement Mortar 1:6 complete all as specified and as directed.

M&L ceramic joint free Coloured Tiles, size 600x100/150mm x10mm in size, vertical Laid and Jointed in Neat Cement Slurry and Pointed in Coloured Cement to match the shade of the Tiles,including rendering 15mm thick as in skirting in Cement Mortar 1:4 complete all as specified and as directed.

M&L Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing laid over and including 15mm thick screed bedding layer in cement mortar 1:4 for laying in floor etc complete all as specified and as directed.

M&L kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement rendering and jointed including 10mm thick rendering in cement mortar 1:3 Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the shade of the Tiles/slab complete all as specified and as directed. all as specified and as directed.

M&L for 75 mm thick cement concrete 1:3:6 using 40mm graded stne aggregate as in plinth protection and courtyard, finished cement surfaces even and smooth/fair with out using extra cement complete all as specified and as directed.

M&L for Chequered Cement Concrete Tiles 25x25x22mm thick pre printed colour , Set and Jointed in Neat Cement Slurry with Grey Cement and Pigment over and including Screed Bed 15mm thick in Cement Mortar 1:6 as in Path, complete all as specified and as directed. Make: Hindustan/coral/SP Tile

S&F of CPVC SDR 11 pipe 20 mm dia fixed to concealed/wall, ceilling,laid in floor etc incl all fittings fixed with solvant and brass threaded fitting for fixing taps etc in any Situation including Taking down un serviceable 15mm dia Steel Water Tubing with Fittings and Connections, etc., complete all as specified and as directed.

S&F of CPVC SDR 11 pipe 25 mm dia fixed to concealed/wall, ceilling,laid in floor etc incl all fittings fixed with solvant and brass fitted fitting for fixing taps etc in any Situation including Taking down unserviceable 20mm dia Steel Water Tubing with Fittings and Connections, etc., complete all as specified and as directed.

S&F Brass CP Fency wall mixer 15mm Bore, with hand shower and neccesary taping items,Cast Copper Alloy with Capstan Heads, screwed down high pressure with or without lettered ‘HOT’ or ‘COLD’ with long screwed Shanks and Fly-Nuts, screwed for Iron Pipe and fixed-in-repairs, complete all as specified and as directed.

S&F brass CP fency Pillar Taps 15mm Bore, Cast Copper Alloy with Capstan Heads, screwed down high pressure with or without lettered ‘HOT’ or ‘COLD’ with long screwed Shanks and Fly-Nuts, screwed for Iron Pipe and fixed-in-repairs, complete all as specified and as directed.

S&F Fancy type two way Pillar Taps mixer 15mm Bore,Chromium Plated cast copper alloy, screwed down high pressure with or without lettered ‘HOT’ or ‘COLD’ with long screwed Shanks and Fly-Nuts, screwed for Iron Pipe and fixed-in-repairs, complete all as specified and as directed.

S&F Angle Stop Cock 15mm Bore (dia), Chromium Plated, screwed down, screwed for Iron Pipe or for Brass Ferrule and fixed-in-repairs complete all as specified and as directed.

S&F Vitreous China Soap Dish, Single, as approved, fixing with Brass Chromium Plated Screws including Taking down unserviceable Soap Dish of any description, complete all as specified and directed.

S&F Brass Chromium Plated Health Faucet with 1.0m long PVC pipe with SS flexible cover, as Approved, including Taking down unserviceable Health Faucet of any description, complete as all specified and directed.

S&F Brass Chromium Plated Towel Rail 900mm Long, as Approved, fixed including Taking down unservice-able Towel Rail of any description, complete as all specified and directed.

S&F Brass CP fancy Bib Cock 15mm Bore (dia), Chromium Plated Long Body, screwed down, screwed for Iron Pipe or for Brass Ferrule and fixed-in-repairs, complete all as specified and as directed.

S&F stop valve CP 15mm bore, cast copper alloy, screwed down, high pressure with long shank or butterfly handle screwed both ends for iron pipe or union and fixed in repairs complete all as specified and as directed

S&F two in one bib taps 15mm bore, cast Copper Alloy,with crutch or butterfly screwed down, screwed for Iron Pipe or for Brass Ferrule and fixed-in-repairs, complete all as specified and as directed.

M&L Vitreous China Wash down Water Closet Pan (Pedestal Pattern) White including fixing Bolts with Plastic Water Closet Seat, White, Closed Pattern with Recessed Bottom and Cover including Chromium Plated Aluminium Hanging Device and fixed-in-repairs, complete all as specified and as directed.

S&F Vitreous China Wash down Water Closet Pan Colour or White composit type including attached Flush tank up to 6-10 ltr water capacity flushing push button flushing system and fixing Bolts (including Flushing Pipe) with Plastic Water Closet Seat, including Mild Steel Chromium Plated Aluminium Hanging Device and fixed-in-repairs, complete all as specified and as directed.

S&F Vitreous China Squatting Pan ‘ORISSA’ Pattern, size 580X440 mm White, with ‘P’ or ‘S’ Trap, Integral Foot Rest, providing Joints between Flush Pipe and Socket of WC Pan excluding Flushing Cistern and Flush Pipe), fixing with and including provision of 150mm thick Lime Concrete Bedding including Taking out unserviceable WC Pan and connected Items, complete all as specified and as directed.

S&F PVC Flushing Cistern 10 Litre capacity, Low Level Valve Less, Syphonic Action type, White, with Inlet, Ball Valve, Float and Handle including Erecting Stand and PVC Flush Pipe of polythene 32mm dia including Taking down/out Unserviceable Flushing Cistern and connected Items, complete all as specified and as directed.

S&F Vitreous China Wash Hand Basin 630X450mm in size, White (Flat Back Type) with 32mm dia Brass Chromium Plated Waste Fitting,UPVC Bottle trap, UPVC’ 32mm bore Waste Pipe, a Pair of Cast Iron Brackets duly Painted/ Erecting Stand including Cutting and Pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 and fixed including Taking down Unserviceable Wash Hand Basin and connected Items, complete all as specified and as directed.

S&F PVC connections 15mm size with brass CP checknut nuts of length 600 mm complete all as specified and directed by Engr-in-Charge.

S&F in repair brass Chromium plated shower roses with or without swivel joints, any size,including fixing to steel pipe or union complete all as specified and as directed by Engr-in-Charge.

Dismantling of old existing PVC/CI/concrete pipes of any description, jointed in cement mortar up to 100 mm dia and removing to store.

S&F PVC (SWR) Pipes 110mm in Bore (dia), Single Socketed, in any length with Rubber Ring Joints fixed to Walls or Laid in Floors, etc, including Taking down /up unserviceable Pipe, complete all as specified and as directed.

All as per item No-69 here-in-before but 75mm dia

S&F PVC (SWR) Bend suitable for PVC (SWR) Pipes 110mm in Bore (dia), jointing with Solvent Cement and fixed, complete all as specified and as directed.

All as per item No-71 here-in-beforebut 75mm dia

S&F 75mm dia sand cast iron soil, waste and vent pipes in any length with or without ears with cement joints fixed to walls complete all as specified and as directed.

S&F 100mm dia sand cast iron soil, waste and vent pipes in any length with or without ears with cement joints fixed to walls with oval access door complete all as specified and as directed.

S&F in repair 75mm dia CI bends with oval access door, diminishing pieces or taperscomplete all as specified and as directed.

S&F in repair 100mm dia CI bends, diminishing pieces or tapers complete all as specified and as directed.

S&F in repair 75mm dia CI branch pieces, single (equal or unequal) ordinary or inverted (Spigot or socket type) or with paralled branches with ovel access door complete all as specified and as directed.

S&F in repair 100mm dia CI branch pieces, single (equal or unequal) ordinary or inverted (Spigot or socket type) or with paralled branches with ovel access door complete all as specified and as directed.

M&L for replacement of 75mm outlet CI floor/nahani trap with stainless steel grating including jointing and breaking/ dismantling any type of floor and making good in cement concrete type B-1, 1:2:4 using 20mm graded stone aggregate and testing after repairs and taking down existing trap etc complete all as specified and directed.

S&F in repair stack clamp made out of GI angle and 10mm dia U bolt and nut with washer for 75 and 100 mm dia pipe complete all as specified and as directed.

S&F in repair coloured powder decorative end Knob for vista rod 25mm dia fancy type complete all as specified and as directed.

S&F Decorative Vista Rod 25mm dia Aluminium powder coated with bracket and fixed in repair

M&L for welding in repairs thickness of Metal to be welded n.exc 6mm complete all as specified and as directed.

Taking down existing water tank of cap 250 to 500 ltrs and refixing after necessary water proofing treatment on roof complete all as specified and as directed

S&F in repair 500 ltrs rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including removing of existing RCC old tank complete all as specified and directed by Engr-in-charge .

S&F in repairs ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed 20 mm bore complete all as specified and directed.

S&F 20 mm Bore gun metal gate valves with iron wheel head screwed both ends fixed-in-repairs complete all as specified and directed.

S&F Stainless Steel Kitchen Sink with Drainage Board of Overall Size 915X460mm and Bowl Size 410X330X160mm, made of Stainless Steel 1.0mm thick Sheet with Plugs, Chromium Plated Waste Coupling and Washer including Bedding in Cement Mortar 1:4 to Dwarf Wall or fixing Cantilever Brackets and Connection to Pipe including Taking down unserviceable Sink and Connected Items complete all as specified and as directed by Engr-in-Charge.

S&F in repairs for Steel Plate Rack size min 0.60x0.90 m with 1mm thick sheet complete all as specified and as directed.Make-Nirali/ Prayag/Neelkamal

S&F Sheet Glass 4.0mm thick Ordinary Glazing as in Window Frames fixed with Wooden oil putty/rubber beads not exc. 0.50 Sqm in Each Pane and fixed in repairs complete all as specified and as directed.

S&F stainless Steel Wire Cloth 0.36mm nominal dia of Wire and average width of aperture 1.4 mm and fixed with Tinned Tacks of Mild Steel Wire Stapes, fixing and repair etc. complete all as specified and as directed.

M&L granite (any type) slab 20mm thick over kitchen platform laid over and including 15 mm thick cement mortar 1:4 as in bedded layer in horizontal and vertical surface and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and directed.

S&F Brass Hat Pegs, Solid body, 175 mm to 250 mm and fixed in repairs complete all as specified and directed.

Taking down door/window frame with shutter of area n exc 1.50 sqm each and removing to store.

Taking down door/window frame with shutter of area exc 1.50 but n exc 4.0 Sqm each and removing to store complete all as specified and directed.

Taking down shutters only of size exc 1.00 Sqm but not exceeding 2.00 Sqm complete all as specified and as directed. Note:- Distrubered area shall be plastered and match with existing surface includin colour including painting work

S&F in repair mild steel works Fe-410 or 310 as in framed works such as door frame/ grills/ guard bar and railing with ends of bars shoulders and or riveted or forged into spiked complete all as specified and directed.

M&L for 30mm thick block board flush shutter with 0.90mm thick lamination on both sides complete fixed to chowkats complete all as specified and directed.

M&L for 2nd class Factory made hard wood, 30mm thick glazed and skelten shutters open repated and prepared to receive framing plain chamfered or rounded fitted with cut and mitered heads for securing glass etc size of member of shutter with all fitting and accessoriese as specified and directed.

S&F PVC Solid moulded Architrave Door Frame of Size 50X47mm & more made out of min 5.0mm Coloured with Plastic Trim decorated PVC Sheet Reinforced with Mild Steel Square Tube as specified in Manufacture’s Instructions complete all as specified and as directed.

S&F Factory Made PVC Solid moulded Architrave Door Shutter 30mm thick (Style) consisting of Frame made out of Mild Steel Tubes for Top and Bottom Rails, Mild Steel Frame shall be covered with heat moulded Plain Colour PVC 'C' Channel having a PVC Sheet Strip of 20mm width stuck inside with Solvent Cement for Stiles and Plain Colour PVC Sheet for Top Rail, Lock Rail and Bottom Rail on either Side and as Gap insert for Top Rails & Bottom Rail, Panelling of Plain Colour PVC Sheet to be fitted in the Mild Steel Frame welded/sealed to the Stiles and Rails with suitable PVC Sheet Beading and Joined together with Solvent Cement and fixing in the Frame at Site as per Specifications and Drawings, complete all as specified and as directed.

S&F 150mm long Aluminium anodised handles, cast type complete all as specified and as directed.

S&F 200 mm long aluminium anodized barrel tower bolt of extruded section complete complete all as specified and as directed.

S&F Mild Steel Butt Hinges 100mm, Medium Weight, Cold Rolled ISI Marked and fixed, complete all as specified and as directed.

S&F in repairs 300 mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (Bolt type ) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

M&L for preparation of new wooden surfaces of any description not otherwise described over 10cm width or grith and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed

Taking down steel window with shutter of area exc 1.50 sqm but n exc 4.0 sqm each up to 4 story building complete all as specified and directed by Engr-in-Charge Note:- Distrubered area shall be plastered and match with existing surface includin colour including painting work.

Taking down steel ventilators up to 4 story building complete all as specified and directed.Note:- Distrubered area shall be plastered and match with existing surface includin colour including painting work

S&F aluminium colour powder coated (shade or tint as directed by GE) window frame of three track using Jindal or equivalent section No 20832 (92x31.75x1.50mm) fixed with thrust bolt in walls by drilling and sliding shutter of section No 20844 (40x18x1.29mm) or equivalent section for glass including 4.00mm thick tinted glass fixed with rubber beading and bushes complete in two track and 0.36 mm dia and 1.40mm aperture stainless steel wire mesh fixed with screw and aluminium beading complete all as specified and as directed.

S&F Aluminium colour powder coated (shade or tint as directed by GE) window frame of using Jindal or equivalent section No 20032 (61.85x31.75x1.50mm) fixed with thrust bolt in walls by drilling for half bottom and top half with top hung shutter using suitable section with 4mm thick tinted glass complete all as specified and as directed.

M&L for preparation and old decorated surfaces of steel and iron surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed.

M&L for preparing old plastered surface of walls applying two coats and finish with distemper oil emulsion over a coat of primer over 3 mm thick birla putty for surface peparation complete all as specified.

M&L for preparation of old surfaces of wood or wood based materials over 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed.

M&L PCC type B0 (1:2:4) (using 12.5mm Graded Stone Aggregate) in hold fast block complete all as specified and as directed.

Excavation in trenches in soft/loose soil not exceeding 1.50 Mtrs wide and not exc. 1.5 Mtr deep and getting out for taking out/laying cable, poles &stay etc complete all as specified and as directed

Demolition of cement concrete of any description and in any position not otherwise specifically provided forcomplete all as specified and as directed

Returning, filling in including spreading leveling, watering and well ramming in layers not exc 25 cm thick after the cable have been laid tested complete all as specified and as directed.

Removal of excavated surplus soil to a distance not exc. 50 Mtrs and depositing where directed at a level not exc 1.5 Mtr above the starting point complete all as specified and as directed.

M&L for sand cushioning to under ground cable provided with layer of sand (8cm deep before laying the cable and 15 cm deep after laying the cable ie total 23 cm complete all as specified and as directed.

M&L for brick laid in trenches for cable protection of burnt clay sub class ‘B’ complete laid dry flat complete all as specified and as directed.

Laying only old serviceable bricks for cable protection (retrieved under item 118 of sch 'A'.

M&L for PCC 1:2:4 type B2 using 40mm grade stone aggregate as in copping of electric pole or making good of disturbed surface complete all as specified and as directed by Engr-in-Charge

M&L for driling hole under hard standing / road for laying of pipe for protection of cable etc by means of manual booklet and without disturbing the top surface or cutting and making good the disturbed surface to the existing if any complete all as specified and directed

Supply and laying GI tube light grade 80 mm bore complete all as specified and directed. Make - Jindal/TATA/BST/Swastik.

Taking out old unserviceable underground cable of 1100 Volts grade with stranded aluminium conductor of size 35 sq mm 3.5 core from excavated trenches /pipes complete all as specified and directed

All as per item No. 128 but size 50 Sqmm, 3½ Core .

Supply, laying and testing of cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 35 sq mm 3.5 core complete all as specified and directed

All as per item No. 130 but size 50 Sqmm, 3½ Core .

Taking down of old unserviceable copper / aluminium point wiring (light, fan, socket or power) complete including fitting & fixture such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions seperately) and making good disturbed surfaces of walls, floors etc complete.

Taking down of old unserviceable sub main wiring of any capacity/Size complete all as specified and as directed.

Material and labour for point wiring complete with 1.5 sqmm PVC insulated unsheathed 1100 volts grade cable stranded copper conductor single core in and including Concealed PVC conduit of 20/25 mm heavy duty complete with 1.5 sqmm PVC insulated copper conductor earth wire and connected to earth dolly for one light point controlled by one switch complete all as specified and directed for One light/fan point controlled by one switch. Make of cable Finolex/Plaza/Havells and make of cionduit National/prestoplast/AKG

All as per item No. 134 above but for 05 Amps bell point complete all as specified and as directed.

All as per item No. 134 above but for 05 Amps socket outlet on same board complete all as specified and as directed.

All as per item No. 134 Above but One 5 pin, 5 Amps socket out let on independent board with 1.5 Sqmm cable & alongwith 1.5 Sqmm continous earth wire of copper conductor complete all as specified and as directed.

All as per Item No. 134 above One 15 Amps socket out let or for sheet metal enclosure on independent board with 2.5 sqmm cable alongwith 2.5 Sqmm continuous earth wire of copper conductor complete all as specified and as directed.

All as per Ser item No. 134 Above but for Point controlled by two numbers two way switches complete all as specified and as directed.

Supply and fixing ceiling rose 2 to 3 terminals complete all as specified and as directed.

S&F switch modular type 06 Amps single pole one way 240 volts complete all as specified and as directed.

S&F socket out let modular type 5 pin 6 Amps complete all as specified and as directed.

Supply & Fix in replacement of switch Modular one module two way 06 Amp complete all as specified and as directed.

Supply & Fix in replacement of bell switch Modular one module complete all as specified and as directed.Make:- Havells/Anchor

S&F twin socket modular type heavy duty out let 6 pin 6/16 Amps complete all as specified and as directed. Make:- Havells/Anchor

S&F switch modular type 16 Amps single pole one way 240 volts complete all as specified and as directed. Make:- Havells/Anchor

S&F modular fan regulator step type 120 watt 2 modular complete all as specified and as directed.Make:- Havells/Anchor

M&L for GI box for fixing of switches 3 modular complete all as specified and as directed.

M&L for GI box for fixing of switches 08 modular complete all as specified and as directed.

S&F modular white cover plate (inner & outer) 3 modular complete all as specified and as directed.

S&F modular white cover plate (inner & outer) 8 modular complete all as specified and as directed.

Taking down tubelight fitting any type & make and refixing the same after repair of the bldg on same location complete all as specified and as directed

Supply & Fix ventilating fan PVC body type 200mm sweep complete all as specified and as directed.

Supply & Fix Ceiling Fan 1200mm sweep 3 blade single phase 5 star energy rating 230V 50 Hz complete with all accessories. Make:- Crompton Greaves/Havells/ Philips

S&F sheet metal enclosure for 220 Volts 20 Amps with a three pin and earth plug top with socket and one single pole MCB 20 Amps complete all as well specified and as directed.

S&F DB, SPN 415 Volts 04 ways double door complete all as specified and as directed

S&F DB, SPN 415 Volts 08 ways double door complete all as specified and as directed .

S&F DB, TPN 415 Volts 08 ways double door vertical type complete all as specified and as directed .

S&F MCCB 125 Amps, 3Pole, 16KA complete all as specified and as directed .

S&F of MCB SP-6-32 Amps, 240 Volt B series type complete all as specified and as directed .

S&F of MCB SPN 40 Amps,240 Volt B series type complete all as specified and as directed .

S&F of MCB TP 63 Amps,240 Volt B series type complete all as specified and as directed.

M&L for sub main wiring two run of 06 sqmm and one run of 4 sqmm continuous earth wire PVC insulated unsheathed stranded copper conductor cable1100V grade drawn in and including PVC surface conduit suitable size of medium grade fixed on wall/ceiling/passing through wall etc connected as required at site complete all as direcetd.

M&L for sub main wiring four run of 06 sqmm and two run of 4 sqmm continuous earth wire PVC insulated unsheathed copper conductor cable ISI marked 1100V grade drawn in and including PVC surface conduit suitable size of medium grade fixed on wall/ceiling/passing through wall etc connected as required at site complete all as direcetd.

M&L for inverter wiring with FR cable 2.5sqmm single core unsheted cable in existing conduit complete all as specified and as directed.

Supply, installation, testing and commissioning Modular/combinable Outdoor Floor Mounting polycarbonate insulated panel which should be shock proof, safe, IP 65 according to IEC 60 529, weather proof, rust proof, UV resistant, halogen free, silica free, corrosion proof, protection class II, totally insulated, having internally embedded gasket with provision for cable entry through detachable flanges , flame retardant, self-extinguishing with glow wire test at 960 C according to IEC 60 695-2-11; chemical resistance towards acid, benzene and mineral oil; Impact strength IK 08 (5 Joule) in accordance with DIN EN 50 102. The panel manufacturer should confirms the Panel is in accordance with IEC 61 439-1& IEC 61 439-2 and Routine Test Certificate shall be submit according to that along with Panel.

The manufacturer of board/ panel SHALL submit a copy of TYPE TEST REPORT ( ASTA certification by CPRI) of a board made out of polycarbonate thermoplastic panel in accordance with IEC 60439-1. The CPRI report shall have mention of following tests performed and passed out satisfactorily. Temperature Rise Dielectric Properties short circuit withstand current rated peak & short time withstand current and Rated Conditional Short Circuit Current Effectiveness of Protective Circuits Clearance & Creepage Distance Mechanical Operation (a) Panel should be with Padlock facility. (b) The Moduler enclosure to assemble Panel should be add with Polycarbonate wedges links. Panel Details Size - 980 [L] x1525[H] x247 [D] mm Incomer - 100A 4P 25 KA MCCB -1 No Outgoing - 32A 4P 10KA MCB -6 Nos Provision of Three Phase (5-30A) Energy Meter - 6 Nos Make- HENSEL

M&L for Earthing Complete with galvanised steel earth plate electrode 60cm X 60cm X 6mm thick, buried directly in ground ( earth pit not less than 2.25 meters deep below ground level ) with top edge of the plate not less than 1.5 meters below normal ground level, connected to galvanised earth lead wire 4.00 mm dia by means of bolts , nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate coonected to earthing testing point including testing complete all as specified and as directed.

Commercial Traders

M/S ANIL KUMAR

M/S Chhavi Constructions Co

Phogat Builders

M/S Sunil Steel Works

Shiv Shankar Nirman Co.

L G BUILDERS