Construction VIP and VVIP Guest House for the Honarable Judges in the premises of Honarable Madurai Bench of Madras High Court at Madurai in Madurai District

Amount

Earthwork excavation for foundation in all soils and sub soils and to full depth as may be directed in following type of soils except in rock requiring blasting for ordinary soil hard red earth shales,murram,gravel stoney earth but inclusive of shoring, strutting and baling out water wherever necessary and refilling the sides of layer of not more than 15cm.thick well rammed and consolidated depositing surplus earth within the compound in places shown by the deparatmental officers with an initial lead and lift and leveling the same etc., complete complying with standard specifications.

Eartwork open excavation in all soils and sub soils and to full depth as may be directed except in rock requiring blasting inclusive of shoring, strutting and baling out water wherever necessary and depositing the excavated earth within the compound in places shown by the departmental officers with an initial leads and lift etc., complete complying with standard specifictions.

Cement concrete 1:5:10 (one cement, five crushed stone crushed stone sand (M- Sand) and ten aggregate)using 40mm HBGS jelly for foundation including dewatering if found necessary and laid in layers of not more than 15cm thick,well rammed complete complying with standard specifications.

Cement concrete 1:5:10 (one cement, five crushed stone crushed stone sand (M- Sand) and ten aggregate)using 40mm HBGS jelly for Flooring including dewatering if found necessary and laid in layers of not more than 15cm thick,well rammed complete complying with standard specifications.

Supplying and filling in foundation and basement with filling Stone dust in layer of not more than 15cm thick.well watered, rammed and consolidated complying with standard specification.

Supplying and filling with conveyed earth from 3KMMR by lorry in basement filling including conveyance loading and unloading charges and all other incidential charges filling laying watering and consolidation etc., complete as directed by the Dept., Officers with standard specification.

Supplying and filling in foundation, basement, etc with filling sand in layers of not more than 15 cm thick well watered, Without consolidation etc. complete complying with standard specification and as directed by the departmental officers.

Brick work in following items in Cement Mortar 1:5 (One cement and five crushed stone crushed stone sand (M-sand) using best quality of country bricks of size 8-3/4" x 4-1/4" x 2-3/4" including pointing with same mortar, levelling and curing etc.,complete complying with standard specifiction.

For Foundation and Basement.

For superstructure in Ground floor

Brick work in following items in Cement Mortar 1:6 (One cement and six crushed stone crushed stone sand (M-sand)) using best quality of country bricks of size 8-3/4" x 4-1/4" x 2-3/4" including pointing with same mortar, levelling and curing etc.,complete complying with standard specifiction.

For superstructure in Ground floor

For superstructure in First floor

For superstructure in Second floor

For superstructure in THIRD FLOOR

For superstructure in Fourth FLOOR

For superstructure in Fifth FLOOR

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid over silver oak joists of size 10cm x 6.5cm spaced at about 75cm centre to centre or at suitable intervals etc. complete.

Supplying and erecting centering for sides and soffits including supports and strutting upto 3.29m height for plane surfaces as detailed below in all floors with all cross bracings using mild steel sheets of size 90x60cm and BG 10 gauge stiffened with welded mild steel angles of size 25x25x3mm for boarding laid over silver oak joists of size 10x6.50cm spaced at about 90cm c/c and supported by casurina props of 10cm to 13cm dia spaced at not less than 75cm c/c aat suitable intervals etc., complete in all floors for complying with standard specifications and as directed. The payment for centering shall be made only after the concrete laid.

Plane surfaces such as RCC floor slab, roof slab,rectangular, square, Tee or Ell beam, intels, bed nblocks staircase waist slab,landing slab,landing beams, portico beams, portico slab etc.,

Plane surface such as RCC square or rectangular columns, top and bottom slab of sunshade, boxing sill slabs, etc.,

For plane surfaces such as vertical slab, side slabs of boxing, vertical drops, facia, vertical wall, etc.

Providing and laying in position, standardised concrete Mix M-25 Grade in accordance using 20mm with IS:456-2000, and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 350 kglms and maximum water cement ratio of 0.50, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability with about (5.0 cu.m.) 7730 k9. of 20mm machine crushed stone jelly and with about (3'3 cu'm') 5156 kg. of 10-12mm machine crushed stone jelly and with about (4.79 cu'm') 7670 kg' of sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards. (No separate payment will be made by the Department for the excess usage of materials).

For foundation and basement

For superstructure in Ground floor

For superstructure in First floor

For superstructure in Second floor

For superstructure in Third floor

For superstructure in Fourth floor

For superstructure in Fifth floor

Supplying,fabricating and placing in position steel reinforcement using mild steel or ribbed for steels ro;ds for all RCC works as per the design given including cost of steel and binding wire slab in all floors etc., complete complying with standard specifications.

Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers.

Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers

Brick partition walls of 10.80cm thickness using best quality country bricks of size 8-3/4" x 4-1/4" x 2-3/4" in Cement Mortar 1:3 (One Cement and Three crushed stone crushed stone sand (M-Sand)) using hoop iron reinforcement if found necessary including curing etc. complete and as directed by the departmental officers. (Hoop iron reinforcement will be measured and paid for separately)

For Superstructure in Ground Floor.

For Superstructure in First Floor.

For Superstructure in Second Floor.

For Superstructure in Third Floor.

For Superstructure in Fourth Floor.

Supplying and fixing in position best approved of BIS quality PVC rain water down fall pipes having a pressure of 4 kg. / sq.cm including cost of necessry PVC shoe, PVC bend, cast iron gratings of required diameter and special clamps, brass screws, nails, etc., and fixing of cast iron gratings at junction of parapet and the RCC roof slab including finishing neatly etc., complete. The rate shall be inclusive of cost of removable cast iron grating. The PVC pipe shall be fixed in wall with special type of "U" clamp at the centre of the pipe line in addition to those for more than 3.0 metre pipe length, etc., complete complying with standard specification. 110mm dia PVC Pipe

Providing and fixing of ABS (Acrolynitrile Butadiene Styrene) Door using factory made plain FPVC (Foamed Polyvinyl Chloride) door frame of the size 105 x 40mm with a wall thickness of 10mm made out of extruded rigid FPVC profile mitre joined with 10 Nos. of 50mm long screw. The door frame shall be fixed to the wall by using 80mm long screws through the frame with the help of PVC fasteners to be provided for each vertical member, stiffeners of („U‟ Channel of size 29 x 9 x 1mm, 150mm long) 3 Nos. at hinge point, frame reinforcement of („U‟ GI Channel of size 46 x 22 x 0.06mm), bottom tie rod of („U‟ GI Channel size of 15 x 15 x 1mm), the ABS Shutter of 35mm thick factory made plain pre-laminated. ABS (Acrolynitrile Butadiene Styrene) door shutter moulded in different designs, consisting of all round Frame made out of water proof solid foam PVC bar of size 20x32mm, reinforced by 32 x 32mm - 2 Nos. for vertical made out of LVL (Laminated Veneer Lumber),

core material of 32mm thick high density craft paper honey comb board, sandwiched on both sides with pre-laminated ABS sheet thickness of 1.5mm. PVC edge banding of size 0.45mm on the vertical sides. Hardware made out of ball bearing butterfly hinges - 3 Nos. for each shutter and ISI make SS round lock complete, including cost of Materials, conveyance and all other incidental charges and labour charges for fixing the Door neatly etc., complete complying with the standard specification. The door shutter and frame should be got approved from the Executive Engineer before use on work

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows With mosquito net of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames.The window should be got approved from the Executive Engineer before use on work

Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned.Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The ventilator should be got approved from the Executive Engineer before use on work

Suplying and fixing M.S Grill for Window & Ventilators including cost of materials and labour charges for cutting to required sizes,fabricating,welding and transporting at site of work and including the cost of one coat red oxide primer etc., complte complying as directed by the departmental officers.

Manufacturing, Supplying and Fixing Ghana Teakwood handrail having a size of 65 X 90mm with Groove to seperate a Head and Base fixed over a flat plate of 40 X 6mm thick. 50 mm dia and 304 L Stainless steel pipe post of 1.6mm tk as the vertical post at 900mm centre to centre distance with 2 nos os 25mm dia 304 L intermediate horizontal stainless steel pipe of 1.6 mm thick in between. the supports will be grouted into the base concrete and provide with the 65mm tk stainless steel circular base plate of 304 L grade.The Teakwood Handrail finished with rose wood melamine glossy polished finish. The rate shall include for grouting into concrete with the necessary supporting arrangements the handrail in the floor polishing buffing, cutting, grinding, conveyance, welding charges, electrical charges,etc. complete complying by the departmental officers.

Paving the floor with best quality Double Charged Vitrified Tiles of size 800 x 800 x 10mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three crushed stone crushed stone sand (M- Sand)) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Flooring with following ceramic tiles of size 305 x 305 x 6 mm laid over 20 mm thick cement mortar 1:3 (One Cement and Three crushed stone crushed stone sand (M- Sand)) base mortar over the existing slab / floor including cutting the tiles to the required size with special cutter wherever necessary, laying in position and pointing with white cement mixed with colouring pigment at the rate of 0.3 Kg. / sq.m. etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the floor with best quality vetrified Tiles of size 600 x 600 x 8mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three crushed stone crushed stone sand (M- Sand)) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Dadooing walls with colour designed digital printed ceramic tiles of size 300mm x 450mm x 8mm and above in best approved quality tiles set in Cement Mortar 1:2 (One Cement and Two crushed stone crushed stone sand (M- Sand)) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers.

Dadooing walls with printed design colour glazed tiles of size 1200 x 600 x 8mm set in Cement Mortar 1:2 (One Cement and crushed stone crushed stone sand (M- Sand)) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers.

Paving the floor with best approved quality fine polished Granite Stone Slabs of size 1200 x 600 of 18 / 20mm thick of Synthetic Grey, Paradise and similar varieties with machine cut edges laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (One cement and three crushed stone crushed stone sand (M- Sand) fixing the slabs with required cement slurry and laid in true right angles with minimum possible width of joints and pointing the joints with white cement mixed with mathcing colouring pigments etc., The granite stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard speicification.

Nosing the granite for with requied shape and design with hand machine etc., complete complying with standard specification and as directed by the departmental officers.

Paving the floor with Industrial Vertified tiles of 600x 600x 10mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and three crushed stone crushed stone sand (M- Sand)) 10mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works)

Paving the floor with kota stone slab of size 600 x 600 of 18 / 20mm (un-polished) in all floors laid in of cement mortor 1:3 (one cement three crushed stone crushed stone sand (M- Sand)) 20mm thick and pointed with colour cement neatly including polishing with polishing stone and oxalic acid etc., so as to perfectly smooth and glossy and including hire charges for polishing machine and power consumption charges etc. The kota stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work, etc., complete as per standard specification.

Supplying, fabricating, erecting and fixing gyp board false ceiling upto a ceiling height of 4.5m from floor level etc., complete and as directed by departmental officers. Using plain sheets (10mm thick)

Manufacturing, supplying and fixing Precast Reinforced Cement Concrete slabs of following thickness in RCC 1:2:4 (one cement, two crushed stone crushed stone sand (M- Sand) and four aggregates), using following HBGS jelly excluding cost of reinforcement steel in position but including cost of moulding charges, casting of slab, finishing, curing and fixing in position in all floors etc., complete complying with standard specification and as directed.a) 50mm thick Precast slab (using 20mm HBGS Jelly)

Plastering with Cement Mortar 1:5 (One cement and Five Plastering crushed stone sand (P-sand)), 12mm thick mixed with bonding agent cebex 112, zydex - zycrete 2x or other equivalent compound confirming to BIS at 200ml of 1 cement bag 50 kg for increased workability and air entraintment used finished in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers.

Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three Plastering crushed stone sand (P-sand)) 10mm thick mixed with bonding agent cebex 112, zydex - zycrete 2X or equivalent compound confirming to BIS at 200ml of 1 cement bag 50 kg for increased workability and air entraintment used finishedand curing, etc., in all floors complying with standard specification and as directed by the departmental officers

Plastering with Cement Mortar 1:3 (One Cement and ThreePlastering crushed stone sand (P-sand)) 12mm thick mixed with water proofing compound conforming to BIS at 2% by weight of cement used including finsihing, curing, etc., complete in all floors complying with standard specification and as directed by the departmental officers.

Supply of Wall putty and applying two coats of putty to the newly plastered wall surface of approved quality including the cost of cleaning the plastered surface by manual labour and including cost of all materials, labour charges as directed by the departmental offices etc. complete complying with standard specification.

Painting two coats of newly plastered wall surface with ready mixed plastic Interior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Painting two coats of newly plastered wall surface with ready mixed plastic Exterior emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification.

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Stitching, Supplying and fixing curtain cloth for Doors/Windows made up of Satin Jacquard fabric of approved Quality colour and design stitched with adequate no, of frills and with provision for hanging the curtain cloth on to the screen rod. The stainless steel 25mm screen rod of ornamental type of size has to be fixed firmly on the wall with brass screws. The ornamental screen rod to be got approved by the Executive Engineer before use. The rate includes cost of screen cloth, screen rod, brackets, brass screws, etc. labour charges for stitching etc. as directed by the departmental offices etc. complete complying with standard specification.

Supplying, laying and jointing CPVC pipes (chlorinated Poly vinyl chloride) pipe( Higher pressure rating with h ig her pipe thickness) Standard Dimension Ratio- 11) of approved qualityand best variety conforming to BIS of the following dia including cutting, threading and fixing CPVC specials using SOLVENT OF 118ML (but excluding cost of such specials) and fixing into wall with teak wood plugs,CPVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The CPVC pipes shall be got approved by Executive Engineer before use on works. (The Above ground level) For External water supply

50 mm dia CPVC Pipe

Supplying, laying and jointing CPVC pipes(chlorinated Poly vinyl chloride) pipe( Higher pressure rating with higher pipe thickness) Standard Dimension Ratio- 11)of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing PVC specials using SOLVENT OF 118 ML (but excluding cost of such specials) and fixing making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works. . (The Below ground level) For external water supply

50 mm dia CPVC Pipe

Supplying, laying and jointing CPVC (chlorinated Poly vinyl chloride) pipe( Higher pressure rating with higher pipe thickness) Standard Dimension Ratio- 11)of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing CPVC specials using SOLVENT OF 118ML (but excluding cost of such specials) and fixing into wall with teak wood plugs, CPVC clamps and screws making holes on the wall (or) drilling holes in the roof and making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The CPVC pipes shall be got approved by Executive Engineer before use on works. (The Above ground level) For Internal water supply

15mm dia cpvc Pipe

20 mm dia cpvc Pipe

Supplying and fixing in position the following CPVC Specials of heavy type and approved quality and good variety excluding fixing charges but including necessary cutting and threading of CPVC pipes, jointing the CPVC specials and painting with two coats with good variety and best quality synthetic enamel paint over a coat of red oxide primer and jointing the specials with pipe line using shellac etc., complete complying with standard specification(The CPVC specials should be got approved by the Executive Engineer concerned before use on works.)

20 mm.dia CPVC Elbow.

25 mm.dia CPVC Elbow.

50mm.dia CPVC Elbow.

20mm.dia CPVC Tee

25mm.dia CPVC Tee

50mm.dia CPVC tee

32x25mm.dia CPVC Reducer

25x20mm.dia CPVC Reducer

20x15mm.dia CPVC Reducer Elbow

Supplying and fixing New PVC WATER TANK of approved quality conforming to ISI.specification 2000 litre capacity having suitable cover, bolts including cost of tank, taxes, transportation to work spot, fixing in position at place as shown and as directed by the Departmental Officers including conducting required water test complete complying with standard specification. Per Litre Rs.10.05/- SOR 2023-2024.

Supplying and erecting and commissioning 5.00 HP Monoblock motor with accessories conforming to ISI Std., assembling over the clamp in dismantling brick masonry fixing bed clamp with angle purline etc, in to the wall redoing dismantling portion neatly including labour for fixing the motor with proper alignment to the suction, delivery pipe etc., complete.

Supplying and fixing in position first quality and approved variety of Gun metal Gate Valve / Wheel Valve with BIS make of the following dia including cost of shellac, thread balls, etc., complete complying with standard specifications

50 mm.dia G.M.Gate valve

25 mm.dia G.M.Wheel Valve

Supplying and fixing in positon Indian Water Closet (Oriya type) of size 580 x 440mm white glazed earthern ware of approved quality and brand with "P" or "S" trap conforming to BIS with M- Sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 (One lime, Two M- Sand and Five brick jelly) 100mm thick and finishing the top to the required slope and including giving necessary connection to PVC pipes (including the cost of 100mm dia PVC pipe for a length of 600mm) by dismantling brick masonry wall / reinforced cement concrete roof / floor slab and making good the dismantled portion to the original condition with leakages etc., complete

Supplying and fixing in position White Glazed Model Wall Mounted Jaquar European Water Closet of best quality and approved make with 100mm “P” or “S” trap connecting with 100mm dia / PVC pipe of 110mm dia, double flapped rigid PVC black seat and seat cover with CP brass hinges including cost of white cement, cement for packing, spun yarn, teak wood plugs, brass screws, etc., including supplying and fixing 10 litres capacity PVC / 12.5 litres capacity porcelin low level flushing tank with a pair of CI brackets, etc., complete with all fittings, such as, 15mm brass ball valve with polythene float with brass handle, union coupling connected by means of 40mm white PVC flush hand using indian adopter joint including all internal fittings, such as, 15mm bras connections, 15mm GM wheel valve, 15mm brass nipple (2 Nos.), 15mm nylon connection, TW plugs, screws and also giving necessary connection to the PVC pipe and painting the CI brackets with 2 coats of approved paint over one coat of red oxide primer, dismantling the masonry and re-doing the dismantled masonry to original condition, etc., complete complying with standard specifications.

Supplying and fixing in position Jaquar or equivalent bewelled edge mirror of approved quality and brand of size 600x450x5.5mm.shelf type with necessary plywood backing, rubber bottons, brass CP screws, T.W.plugs etc.,complete complying with standard specification.(The mirror should be got approved by the Executive Engineer before use on works)

Supplying and fixing in position best approved quality Stainless Stell Towel rail of Jaquar or Equivalent make 600mm length 20mm.diametre with brackets of same material including cost of teak wood plugs and etc.complete complying with standard specifications.(The towel rail should be got approved by the Executive Engineer before use on works.)

Supplying and fixing in position best approved qualtiy Stainless Stell Soap tray jaquar or Equivalent make of size 150x100mm. Including cost of teak wood plugs, brass screws, etc., complete complying with standard specification and as directed by the departmental Officers.

Supplying and fixing in position Jaquar or Equivalent make white glazed earthernware wash hand basin of size 550 x 400mm (with pedestal) with a pair of cast iron brackets, including cost 15mm dia brass CP pillar tap, 32mm dia "B" class GI waste pipe with rubber plug and chain, 15mm dia GM wheel valve, 15mm brass nipple, 15mm dia nylone connection, 32mm dia CP brass waste coupling including fixing of wash basin using CI brackets on to the wall in position with TW plugs and screws, rubber washers, white lead and giving necessary water supply connection and painting the brackets with two coat of painting over a priming coat of anti-corrosive paint including testing for leakages etc., complete complying with standard specification and as directed by the departmental officers. (The wash hand basin and specials should be got approved by the Executive Engineer before use on works).

Supplying and fixing of Jaquar or Equivalent make Stainles steel Health Facet with Stop coak of size 150 x 150mm including cost of teak wood plugs, brass screws, etc., complete complying with standard specifications.

Supplying and fixing Jaguar Ornamental Spout - SPJ 81463 for diverter or equivalent type 15mm dia Spout of best approved make and quality including cutting, threading. G. I. Pipes wherever necessary and fixing to the galvanized iron pipes in position etc., complete complying with standard specification ( Two in One Screw down tap to be used on works should be got approved from the Executive Engineer before use)

Supplying and fixing of Jaquar or Equivalent make Stainles steel Shower rose with Stop coak of size 150 x 150mm including cost of teak wood plugs, brass screws, etc., complete complying with standard specifications. (The Shower Rose should be got approved by Executive Engineer before use on works).

Supplying and fixing of Jaquar or Equivalent make Stainless steel Towel Ring including cost of teak wood plugs, brass screws, etc., complete complying with standard specifications. (The Towel Ring should be got approved by Executive Engineer before use on works).

Supplying and fixing of Jaquar or Equivalent make Stainless steel Paper Holder including cost of teak wood plugs, brass screws, etc., complete complying with standard specifications. (The Paper Holder should be got approved by Executive Engineer before use on works).

Supplying and fixing in position 25mm dia Jaguar or equivalent Bibcock with wall flange of approved make conforming to BIS specifications and quality including cost of shellac, thread, etc., complete complying with standard specification and including cutting and threading wherever necessary. (Taps should be got approved by the Executive Engineer before use on the works)

Angle valve

stop cock

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid Above ground level

For 110mm.dia PVC pipe

For 75mm.dia PVC pipe

Supplying and fixing in position best quality PVC soil / waste pipes of various dia having 6 kg / sq.cm. pressure BIS mark and providing leak proof joints using PVC adhesives including fixing to the wall with special PVC / MS clamp, teak wood plugs, brass screws, etc., and making connection to all sanitary fittings, dismantling masonry / RCC works wherever found necessary and making the good dismantled portion to the original condition, including testing for any leakages, etc., complete complying with standard specifications. (The PVC pipes should be got approved by the Executive Engineer before use on works). The rate for earth work excavation will be measured and paid separately in the cases where the pipe lines are proposed to laid below ground level

For 110mm.dia PVC pipe

Supplying and fixing in position PVC specials of the following dia and types of approved quality confirming to BIS and providing leak proof joints including fixing to the walls and giving connection to the PVC soil stacks, dismantling the masonry or RCC works and re-doing the dismantled portion to original condition etc., complete complying with standard specifications. (The PVC specials should be got approved by the Executive Engineer before use on works).

110 mm dia PVC Plain Bend

110 mm dia PVC Door Y

110 mm dia PVC Plain Bend with door

75 mm dia PVC Plain Bend with door

75 mm dia PVC Plain Bend

Supplying and fixing PVC ventilating shaft of 110mm dia (having working pressure 4 kg. / sq.cm) with 3 metre height including cost of PVC cylindrical cowl of best approved quality etc., complete complying with standard specifications and as directed by the departmental officers

Supplying and filling 20mm gauge I.R.C. metal in DISPERSION TRENCH etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and filling 40mm gauge I.R.C. metal in DISPERSION TRENCH etc., complete complying with standard specification and as directed by the departmental officers.

Supplying and fixing position PVC Nahani Trap / Floor Trap of the following sizes with best stainless steel gratings of approved brand and quality, fixed over a bed of brick jelly lime concrete 1:2:5 (One part of lime, two part of M- Sand and five part of 40mm gauge brick jelly) and finished with Cement Mortar 1:3 (One Cement, Three M- Sand) including dismantling masonry works wherever found necessary and making good the dismantled portions to the original condition and giving connection to the CI / PVC pipes, etc., complete complying with standard specification. (The Nahani Trap should be got approved by the Executive Engineer before use on works)100x75mm with s.s. grating

upto 150m

Supplying suitable size casing pipe for 6" dia borewell ( 6kg/sqcm) of best quality with ISI mark with necessary PVC coupling with socket end, The PVC should got approved by the departmental officers before execution. Without slotted

Supplying suitable PVC End cap ( 6kg/sqcm) of best for casing pipe of 6" dia borewell quality with ISI mark, The PVC should got approved by the departmental officers befoe execution.

Supplying, laying and jointing CPVC pipes (chlorinated Poly vinyl chloride) pipe( Higher pressure rating with h ig her pipe thickness) Standard Dimension Ratio- 11)of approved quality and best variety conforming to BIS of the following dia including cutting, threading and fixing PVC specials using SOLVENT OF 118 ML (but excluding cost of such specials) and fixing making good the dismantled portion to original condition with necessary brick work / cement concrete and plastering neatly wherever necessary with necessary scaffolding charges upto 4 metre height above ground level, etc., complete complying with standard specifications. The PVC pipes shall be got approved by Executive Engineer before use on works. . (The Below ground level) For external water supply 32mm dia For Borewell

Supply of 4.00 sqm, 3 core flat Copper Cable for submersible motor with wire bound having good quality with nylon coir etc., complete.

Supplying and Erecting ISI make submersible pump of 3 HP/ 5.0 Kw model CSM-9 with outer dia 50mm of IS 14220 specification with submersible S/D starter of 8.9 - 13.50 A rekat range with 13.5 A rating and 380-415 V AC coil voltage as per specification. LPMxM(50x175)

Supplying and fixing Nylon rope conforming ISI standard etc., complete as per standard specification and as directed by the Departmental officers.

Supplying and fixing of 3 Phase Panel Board including labour charges etc., complete complying with standard specifications and as directed by the departmental officers.

Teak wood door Supplying and Fixing of Ornamental Teak Wood door with the following pecifications. The Outer door frame of teak Wood size of 150 X 100 mm Scantlings to a Width of 1.80m and height 2.40 m and the door frames should be carved. The shutter Frame made of teak wood Size of 150mm X 40mm for Styles, top rail and bottom rails. The shutter panel covered with teak wood single plank of 40mm thick and the panel should be carved by the design approved by the departmental officers. The entrance door are fixed with brass hinged - 6Nos., 8'' ornamental handle - 2Nos., 300mm X 12mm brass tower bolt, 1No. 200mm x 12mm brass tower bolt - 1 No., brass door stopper - 2 Nos ,bush - 2 Nos. and good Quality and variety of lock - 1No, - All the wooden fixtures are tightened by brass screws with wooden plank frames as directed. The door frames is fixed to wall with M.S.clamps by dismantled portion to original condtion after fixing the door in position properly.

Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S. flat sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos. of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided 1no.

Aldrop is provided incase of double leaf door at lock railsection in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements for lock is provided on the rear side of the door at an appropriate place. Incase of double leaf door M.S.Flat 32 x 3mm at 1.1Kg/m is provided on the one shutter t conceal the gap between the two shutters.at an appropriate place in the door. A tie bar is provided at the bottom of the frame to prevent twisting of frame during transportation and fixing. All members are given a coat of red oxide primer as directed by the departmental officers. The rate includes cost of all materials, labour charges, transportation to site of work, loading, un loading and all other incidental charges etc., complete. Single Leaf

Supply and Fixing of M.S. Clamp set of 75mm length 2 Nos with bolts and nuts 8 Nos. of heavy type confirming to IS Specification and as directed by the Departmental officers etc., complete

Labour charges for erection of Submersible pump set in bore well including fixing and jointing submergible cable with proper clamps up to the starter to required depth and also fixing of riser pipes to the and erection of panel board consisting of TPICN switches, starter, volt meter, ammeter, three pilot (indicating) etc., complete complying with standard specification.

Providing Anti-termite treatment to soil adjecent and under building foundation, plinth periphery of the building by application of chemicals of IS 63613 part I to IV in stages to suit the progress of work consist as per the detailed specification as below. Including breaking of termite mounds, making holes with crow bar, closing the holes after the treatment and including cost of chemicals, labour charges, transport and storing etc., complete and as directed by the departmental officers.

Stage 1: Spraying Anti termite treatment chemical solution for the foundation before laying the foundation concrete at bottom and sides of the foundation.

Stage 2: Spraying Anti termite treatment chemical solution to the grade beam level, spraying has to be done for the grade beam, brick masonry in the super structure in contact with back fill earth.

Stage 3: Spraying Anti termite treatment chemical solution on sand for the flooring before laying the flooring concrete; the treatment has to be carried out on the sand filling in basement and after leveling operation is over.

Stage 4: Spraying Anti termite treatment chemical solution around the building on outside by making crow bar holes at an interval of 15 cms to a depth of 30 cms before laying the plinth projection. These holes have to be closed after the treatment.

Supply and fixing of Fire fighting application oblique type stainless steel Hydrant Valve of size 63mm dia with oblique type instantaneous coupling with rotating wheel to open and close the valve including MS flange of table “E”, bolts & nuts with washer as per IS 5290 at ring main around the building and wet riser inside the building including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply, and fixing in position of Fire Fighting Application Hose of 63mm dia of 15 metres length binded by copper wire with 63mm dia stainless steel male and female instantaneous fire fighting special coupling as per IS 901 as directed by the Departmental Officers. Near every hydrant points including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary etc complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR/ LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply, and fixing in position of Fire Fighting Application 63mm dia stainless steel short length Branch Pipe with hexagonal type spray nozzle of 15mm (or) 20mm jet bore. Near every hydrant points including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantledportions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply of Fire Fighting Application MS Hose Box to keep two number of hoses and 1 No. of branch pipe with nozzle having proper glass window type double door with universe open key, painted inside white and outside Post Office Red. Near every hydrant point including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT.

Supply, erection, testing and commissioning of Fire Fighting 2 Way Fire Brigade Inlet with necessary gun metal 63mm dia non-return spring shutter arrangements so that to control one way flow at the time of emergency water supply by fire and rescue service fire engine entry including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original conditionwherever found neccessary., etc., complete as per standard specification and as directed by the Departmental Officers. (Make: KIARTAR / OMEX / EQUIVALENT)

Supply, installation of Fire Fighting Application 180 degree swinging type, hose reel drum with 20mm dia braided thermoplastic hose of 30 metres long, so as to extend to necessary distance by self rolling spindle wheel including necessary 20mm dia ball valve and open and close spray nozzle, warm clip, etc., as per the standard pattern of any reputed make at every floor nearer to hydrant valve, including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary., etc., complete as per standard specification and as directed by the Departmental Officers. Make: OMEX / KARTAR / LIFE GUARD / SAFE GUARD / EQUIVALENT

Supply, erection, testing and commissioning of following MS „C‟ Class Heavy Duty Pipe as per IS 1239 to withstand a developing pressure of 10 kg. / sq.cm including necessary fittings like MS flange of table „E‟, elbows, reducers, gaskets, bolt, nuts with washers & joints as per standard method of arc welding, including one coat metal primer and two coat Post Office Red painting including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: JINDAL / EQUIVALENT.

100 mm dia “ c ” Class M.S. Pipe with ISI Mark (Make JINDAL or equivalent)

25 mm dia “ c ” Class M.S. Pipe with ISI Mark (Make JINDAL or equivalent

Supplying and fixing BUTTERFLY VALVE Slim Seal type cast iron lever operator type with required flanges, nuts, bolts etc. complete. as per standard specification and as directed by the Departmental Officers

80 mm dia

100 mm dia

Supply, erection, testing and commissioning of cast iron body and gun metal or stainless steel Internal Non-Return Valve of size of 80mm dia to control one way flow of water to be installed pump room at delivery line and near overhead tank at terrace level near to jockey pump and motor including necessary MS flange of table „E‟, gaskets, bolts & nuts, etc. as per IS 5312 including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers.

Supply, erection, testing and commissioning of Air Release Valve of 20mm dia, so as to release airlock in 100mm dia MS pipe at top most wet riser, including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: KARTAR / EQUIVALENT.

Supply, erection, testing and commissioning of fire fighting application monoblock motor pumpset of 900 LPM at 40 metres head to develop 3.5 kg/sq.cm at the heightest and farthest hydrant point to make 30 m water jet at the time of fire fighting emergency cicumstances, coupled with 11 KW / 15 HP rated three phase 414 volts, 50 Hz, 2880 rpm electrical motor the pump with cast ron body, bronze impeller, rope gland packaging, suction size of 80 mm dia. delivery size of 65 mm dia., including the cost of foundaton concrete anti vibration mounting, rain safety hood and etc. complete as directed by the Departmental Officers (Kirloskar make KDS 1555+ or Equivalent).

Supply,erection,testing and commissioning of Pressure Gauge with 0 to 14kg range of reputed make with necessary valve, milling thread MS coupling fixed at delivery pipe line in pump house to read the developing pressure including conveyance, all incidental charges, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc., complete as per standard specificatin and as directed by the departmental officers.

Supply, erection, testing and commissioning of suitable Pressure Switch of reputed make line Indfoss or Donfoss including necessary valves, couplings, etc., connected with electrical main control panel and setup at proper differential so as to auto start and auto stop the electrical motor, jockey motor including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., completed as per standard specification and as directed by the Departmental Officers. Make: DONFOSS / INDFOSS / ISI MAKE / EQUIVALENT

Supply, installation, testing and commissioning of Micro Processor based conventional 8 Zone Fire Alarm Control Panel having the rating of 24 volt DC power supply, consisting 230 / 24 volt SMPS unit, 2 Nos. of 12 volt 7 AH standby batteries, suitably mounted on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers.

Supply, installation, testing and commissioning of Conventional Smoke Detector suitably mounted on ceiling with MS juction box / false ceiling using fixing accessories like screws, plug, clamps, etc., as per standard methods and as directed by the departmental Officers. (Make: Apollo / Equivalent)

Supply, installation, testing and commissioning of Manual Call Point (MCP) providing on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the Departmental Officers. (Make: Ravel / Equivalent)

Supply, installation, testing and commissioning of Electronic Hooter / Sounder providing on wall using fixing accessories like screws, plug, clamps and etc., as per standard methods and as directed by the departmental Officers (Make: Ravel / Equivalent)

Supply and laying of FRLS PVC insulated 2 core 1.5 sq.mm. Armoured Copper Cable on ceiling / wall using fixing accessories like screws, plug, clamps, etc., as per standard methods and as directed by the Departmental Officers.

Supply and fixing of ABC 6kg capacity Fire Extinguisher as per New IS No. 15683 complete with control valve discharge hose with horn, wall mounting bracket, safety clip etc., including conveyance, all incidental charges, necessary, necessary scaffolding and re-doing the dismantled portions to its original condition wherever found necessary etc., complete as per standard specificatin and as directed by the departmental officers - Omex / Ronak or Equivalent

Providing Polymer Coating (Water Proof Coating) for sunken portion of toilet with following specification and the surface shall be cleaned to remove all dust, foregin, matters lose materials or any other deposits of contamination by rubbing with wire brush. Slurry: Dry blend and polymer liquid blend shall be mixed into the desired ratio as per recommendation of the supplier. The mix shall be stirred thoroughly until no bubbles remain in the mix. Any lumps found in mix shall be removed. Apply first coat of polymer modified cementitious slurry by brush on wet cleaned surface. After drying, second coat shall be applied on the first coat as directed by the departmental officers etc.

Filling Brick Jelly Lime Concrete 1:2:5 using 40mm brick jelly in Lime Mortar 1:2 (one Lime and Two M-Sand) in the sunken portion including Compacting etc., complete and as diredted by the departmental officers

Supplying and fixing Jaguar or Equivalent PVC soap liquid dispenser etc. Complete complying with standard specication.

Supplying and fixing Jaguar or Equivalent 304L grade SS tissue dispenser etc. Complete complying with standard specication.

Supplying and fixing glass partition for toilet Cubical. The glass partition made up of 10mm thick toughend glass and fixed on wall and floor by using stainless steel pipe of 25mm dia at top and S.S glass holder and clamps at necessary places. Nosing should be done on all the exposed edges of glass panel to be finished neat and smooth by grinding. The rate inclusive of all materials, labour charges and transport etc., complete.

Supplying erecting and commissioning 0.7 HP SCALA 2,3,4-5' Pressure Booster motor with accessories confirming to ISI standard with Intelligent pump control constant pressue, integrated dry-run protection asssembling near over head tank including labour for fixing the motor., complete complying with standard specification.

Supplying and fixing float switch inside over head tank for Pressure Booster motor with accessories confirming to ISI standard fixing inside over head tank including labour for fixing the motor., complete complying with standard specification.

Supplying Providing and fixing of Laminated toughened glass handrail(with 16mm thick toughened glass)with 304L grade ss handrail tubes, flats, plates, bullet pins,cips, necessary fctory made glass connectors, SS bottom support, necessary fasteners gaskerts accessories,sealant etc., complete. the rates are inclusive of all material ,labour charge, tools&tackels, transportations , leads &lifts etc., the rate including cost of all labours and to be finishied as per the drawing specifications. and as directioned by Engineer-in charge.(Dorma or equivalent)

Supply, erection, testing and commissioning of following MS Class Heavy Duty Pipe as per IS 1239 to withstand a developing pressure of 10 kg. / sq.cm including necessary fittings like MS flange of table elbows, reducers, gaskets, bolt, nuts with washers & joints as per standard method of arc welding, including one coat metal primer and two coat Post Office Red painting including conveyance, all incidental charges, neccessary scaffolding and re- doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers. Make: JINDAL / EQUIVALENT. 150mm dia

Supply, erection, testing and commissioning of Pressure Gauge with 0 to 14 kg. range of reputed make with necessary valve, milling thread MS coupling fixed at delivery pipe line in pump house to read the developing pressure including conveyance, all incidental charges, neccessary scaffolding and re-doing the dismantled portions to its original condition wherever found neccessary, etc., complete as per standard specification and as directed by the Departmental Officers.

Supplying and erecting in position of following liters capacity Industrial Model Reverse Osmosis Water-cum-Purifier to deliver Potable Water with World Health Organisation (WHO) Standards with following accessories.(a) MS Skid - 1 No.(c) Feed Pump 0.50 HP – 1 No.(e) Membrane 40 x 40 filmtech (or) equilaents / Osmonic (USA) - 1 No. and Membrane Pressure Vessel 40 x 40 -1 No. & Pressure Gauge - 2 Nos.(f) Flow Meter - 1 No. 20” Filter with Housing - 1 No., Low Pressure Switch - 1 No., Level Switch - 1 No. & Necessary CPVC Pipes and Fittings.The system shall be provide with Two Panel Control System with necessary Stainless Valves and Fittings and Float Control etc. The rate should be inclusive of all civil works, wherever necessary to install the System in position and intact

250 Litres Capacity

GROOVING GRANITE SLAB in steps and cleaning etc., complete as directed by the departmental offices.

Supplying & Fixing of stainless sink of size 1200x550x180mm including cost of 32mm dia CP waste coupling, 32mm dia PVC waste pipe with rubber plug and chain, 15mm dia brass nipple including fixing the sink in position and testing for leakages etc., complete complying with standard specifications excluding CI brackets. [The sink and specials should be got approved by the Executive Engineer before use on works]

Supplying and fixing of Jaquar or equivalent Stainless steel Shower drainer etc, complete complying with standard specification.

Providing granolithic floor finish of the following thickness with plain cement concrete 1:2:4 (One Cement, Two sand and Four aggregate) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers)

25mm thick

Plain Cement Concrete 1:2:4 (one cement, two crused stone sand M-sand and four hard broken stone jelly) using 20mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specificatins and as directed by the departmental officers.

Cement Concrete 1:3:6 (One Cement, crused stone sand M-sand and Six broken stone jelly) using 40mm size hard broken stone jelly for dummy columns, excluding cost of centering shuttering reinforcement grills and fabrication charges but including curing etc. complete. (Reinforced Cement Concrete 1:2:4 for slab to be extended upto top of splashing with pressed tiles and future extension rods to be embedded in CC 1:3:6 (One Cement, Three Sand and Six hard broken stone jelly). Dummy columns should be at least 1 metre height)

Plain Cement Concrete 1:2:4 (one cement, two crused stone sand M-sand and four hard broken stone jelly) using 20mm jelly for wearing coat including laying, compacting, finishing and curing, etc., complete as per standard specificatins and as directed by the departmental officers.

Stainless Steel (Salem Stainless Steel) Door Frame (Box Section using Stainless Steel Plate of 1 mm thick) of size 100 mm x 60 mm with a rebate of 30 / 35 mm x 15 mm on one side of the frame including supplying and fixing dovetail splayed end stainless steel Hold fast etc.,

Supplying and fixing Solid core Particle board flush shutter of nominal thick of 35 mm with necessary T.W. internal lipping conforming to IS 2302 with both sides teak ply including supplying and fixing cost of wind appliances and furniture fittings such as 1no .200 x 12 mm aluminium tower bolt 2 nos. 150x12 mm aluminium tower bolts 1no. 250 x 16 mm aluminium aldrops, 2 nos. 200mm ‘D’ type aluminium door handle and door stopper with bush etc., complete as directed by the departmental officers. - Single Leaf

Painting new wood work with two finishing coats of synthetic enamel ready mixed paint of approved quality and colour over one coat priming coat in all floors including the cost of primer etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Supplying and fixing in position CI manhole covers with CI frames (Heavy duty) of size 60cm x 60cm of best approved quality as per standard specification etc., complete compying with standard specifications

Dadooing walls with best approved quality, Granite tiles of size 1200x600x18/20mm thick set in Cement Mortar 1:2 (One Cement and Two crushed stone sand (M-sand)) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers.- Jet Black

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module light / fan marking switch with module front plate and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (5 points / Coil) (Higher End) (DATA-1)

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module light / fan marking switch with module front plate and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (6 points / Coil) Higher End (DATA-2)

Wiring with 3 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A two way module switch with module front plate and making good of the concealed portion with suitable colour for Concealed PVC pipe (Stair case Light point) (Higher End) (DATA-3)

Wiring with 2 x 1.5 sq.mm. (22 / 0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable heavy gauge MS conduit pipe on wall and ceiling with MS accessories with MS switch Box and 5A FT switch and covered with hylum sheet of 3mm thick with painting of suitable colour for light point / fan point. (5pts/coil) (Higher End) (for Lift well) (DATA-4)

Wiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5sqmm PVC unsheathed SC copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (5 points / Coil) (Higher End) (for street light) (DATA-5)

Supply and fixing of single box type 4'-20 W LED fitting (Higher End) with CRCA body complete with TW round blocks on wall or ceiling with 20 W LED tube with PVC unsheathed Copper leads from terminals to the fitting. (DATA-6)

Supply and fixing of 18W LED Square type Recess cum surface fitting (Havells Trimclipon/Eq.) of 6500K CCT with PVC unsheathead copper leads from terminals to the fitting and necessary connection complete. (DATA-7)

supply and fixing of 24W LED 2x2 square type Recessed fitting with LED (Higher end) on false Ceiling with suitable hanging support from ceiling with PVC unsheathed copper leads from terminals to the fitting. (SD-526)

Supply and fixing of WT bulk head fitting with guard suitable for 9W LED lamp (Havells / Eq) with lamp. (DATA-8)

Supply and fixing of 11W LED mirror Light (Higher End) of 3 in 1 CCT (WW, WH, NWH) of IP42 protection with PVC unsheathed copper wire from terminals to the fitting and necessary connection complete. (For Mirror Lighting) (DATA-9)

Supply and fixing of Decorative wall light made up of stainless steel, rust free fixture with white glass diffuser suitable for 9W LED lamp (Havells/Eq) on wall or ceiling with PVC unsheathead copper leads from terminals to the fitting. (DATA-10)

Supply and fixing of Cassiel 5 Layer Rose Gold Finish Contemporary Chandelier of 56.9cm (L) x 56.9cm (W) x 86.4cm (H) dimension with 14Nos of 5W LED filament bulbs of E14 base with necessary accessories and connections complete. (for Living) (Quotation enclosed)

Supply and fixing of 60-Watts 5 Light Flowers Shaped Modern LED flush mounted Chandelier of 50cm (L) x 50cm (W) x 9cm (H) dimension with high quality SS chassis and brushed finish with necessary accessories and connections complete. (for Bedroom) (Quotation enclosed)

Supply and fixing of 48W LED street light fitting with LED (Higher end) with 32mm dia. GI pipe (class B) with 1 no.32 mm GI bend complete on the existing post/ on wall with PVC unsheathed copper leads with MS clamps and with painting. (SD 535)

supply and fixing of 1200mm (48") sweep AC ceiling fan High speed complete with 2 module 100W fan step regulator (Higher end) with 300 mm down rod on the existing fan clamp (SD 581)

Supply and fixing of 300 mm (12") sweep (Light duty) AC exhaust fan complete without provision of hole in the wall. (SD-115)

Supply and fixing of louvers shutters arrangements for 300 mm (12") sweep (light duty) AC exhaust fan. (SD-120)

Supply and fixing of 450 mm (18 inch) wall mount, Oscillating type fan with aerodynamically designed semi transparent PP three blades for noise free operation with in built Speed regulator with necessary accessories with connections complete (Crompton High Flo Wave/ Usha Maxx Air/Orient.) (Data-11)

Supply and fixing of 25 litres capacity 1000W automatic electric water heater with copper container with glass wool / Puf insulation with MS powder coated shell (VENUS/RACOLD) with ISI mark suitable for 230V 50 c/s AC supply on suitable MS clamps with 3 core flex wire but without plumbing work. (DATA-12)

Supply & Fixing of AC / DC 76mm Buzzer /call bell suitable for 230 Volts 50 c/s single phase AC supply on suitable TW round block with 1 Module GI flush mounting box, 1 Module combined plastic cover plate and 1 module Modular type Bell push Switch with indicator complete(Higher End). (DATA - 13)

Supply and run of 2 of 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in rigid pipe concealed in wall and ceiling and making good of the concealed portion with suitable colour. (DATA-14)

Supply and fixing of 1 no.6A two module 5 pin socket, 1 no. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End (SD-464)

Supply and run of 2 of 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour (For 6A Plug) (SD-55)

Supply and fixing of 5A 3 pin and 2 pin combined flush type wall socket with 5A flush type switch in suitable MS box on wall and covered with 3mm thick hylem sheet and necessary connection complete. (Lift well) (DATA -15)

Supply and run of 2 of 1.5 sq.mm (22/0.3) PVC insulated SC unsheathed Cu. Conductor of 1100V Grade in suitable gauge MS Conduit pipe on wall and ceiling with continuous earth wire connection of 14SWG TC wire with Painting of suitable colour. (for Lift well) (SD-42)

Supply and fixing of 1no.6/16A two module socket, 1no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End (SD 488)

Supply and fixing of 3nos.6A two module 5 pin socket, 3 nos. 6A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End (SD - 476)

Supply and fixing of 20A DP plug and socket in sheet enclosure with 32A DP MCB in flush with wall with earth connection (For AC Plug) (SD-140)

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 6 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End (for Lift machine room) (SD 601)

Supply and fixing of 12 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB switch as incoming and 10 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. Higher End (SD 613)

Supply and run of 2 of 4 sq.mm. (56 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour. (Set Plug ,16A Plug and 20 A Plug, 8way SPN DB) (SD-57)

Supply and fixing of 32A FP MCB in sheet steel enclosure in flush with wall with earth connection. (Higher End) (For Lift and Kitchen) (DATA-16)

Supply and run of 4 of 4sqmm (56 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour. (for 32A FP in Kitchen) (SD-61)

Supply and fixing of 7 segment 4 way triple pole neutral MCB distribution board in sheet steel enclosure double door type with metal door with IP 42 protection with 63A 4 pole MCB as incoming and 3Nos 63A DP RCCB as sub incomer and 12 Nos. 6 A to 32 A SP MCB as outgoing in flush with wall and making good of the concealed portion with earth connection. (Higher End) (Lighting Control) (DATA-17)

Supply and clamping of 3½ x 35sqmm PVC aluminium LTUG armoured cable on post or on wall with MS clamps. (for 4 way 7seg & APFC panel) (SD-223)

Supply and fixing of brass cable gland for 3-1/2 x 35 sq.mm. PVC armoured LTUG cable with earth connection. (SD-187)

Supply and providing cable end termination of 3½ x 35 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete. (SD-236)

Supply and fixing of 7 segment 6 way triple pole neutral MCB distribution board in sheet steel enclosure double door type with metal door with IP 42 protection with 63A 4 pole MCB as incoming and 3Nos 63A DP RCCB as sub incomer and 18 Nos. 6 A to 32 A SP MCB as outgoing in flush with wall and making good of the concealed portion with earth connection. (Higher End) (Sub Power Control) (DATA-18)

Supply and Run of 4 of 10 sq.mm. (140/0.3) PVC insulated SC unsheathed copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire with painting of suitable colour. (for 7 Segment and Horizantal DB's) (SD 424)

Supply and clamping of 3½ x 25sqmm PVC aluminium LTUG armoured cable on post or on wall with MS clamps. (For Lift) (SD-222)

Supply and fixing of brass cable gland for 3-1/2 x 25 sq.mm. PVC armoured LTUG cable with earth connection. (SD-186)

Supply and providing cable end termination of 3½ x 25 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete. (SD-235)

Supply, fabrication, erection and comissioning of 125A capacity dust and vermin proof cubical panel board size of 4' X 1' X 4' made up of 16 SWG CRCA sheet steel for outer body, with doors, switch supports and seperations etc., and with supply and fixing of the following interior switch with bus bar chamber complete

with 1" x 1/8" tinned cu. Flat for 3 phase, 1" x 1/8" tinned cu flat for neutral, 1" x 1/8" tinned cu flat for earth connections with bus bar insulators. The following tinned Cu flat should be used for interconnection between busbar and switches: 1" x 1/8" tinned cu. Flat for interconnection of 1No 125A incoming switch to bus bar and no.8 SWG copper conductor for interconnection of 6Nos 63A Outgoing switches to bus bar.A separate chamber on top of one side should be provided with multi function meter to display Line & Phase Voltage, Phase Current, Power Factor and Frequency with one set of LED pilot lamp, fuse holder with suitable HRC fuse for each phase with suitable CT coil arrangements. The panel should be fabricated as per relevant IE rules & CEIG specification for accommodation of 7Nos 3 phase switches and supply & fixing of the following switches.

1. 125A TPN switch disconnector fuse units interior only with HRC fuses double break - 1NoIn each cubical switch, live portion of bus bar should be shrouded by 6mm thick hylum sheet separators, and properly earthed by tinned solid copper flat as I.E rules CEIG sepecifications. The earth bus with two runs of 1" x 1/8"tinned copper flat must be run all round the panel to provide double earth connection. The panel should be painted with two high quality enamel paint over one coat of red oxide primer, the cable size, capacity of switch, location etc., should be marked with white paint and 2 Nos. metallic danger board affixed complete with mounting on base channel 3"x1½"x½" iron frame work support complete. (The TPN switches should be L&T / Siemens make only) (Power Panel) (DATA-19)

Supply and clamping of 3½ x 70sqmm PVC aluminium LTUG armoured cable on post or on wall with MS clamps. (SD-225)

Supply and fixing of brass cable gland for 3-1/2 x 70 sq.mm. PVC armoured LTUG cable with earth connection. (SD-189)

Supply and providing cable end termination of 3½ x 70 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete. (SD-238)

Supply and clamping of 2 Runs of 3½ x 240 sq.mm PVC aluminium LTUG armoured cable on post or on wall with MS clamps. (From MV Panel) (DATA-20)

Supply and laying 2 Runs of 3½ x 240 sqmm PVC armoured aluminium LTUG cable through HDPE pipe in a trench to be excavated at a depth of 0.75 metre and refilling the earth to make good. (From MV Panel) (DATA-21)

Supply and fixing of brass cable gland for 3½ x 240 sq.mm. PVC armoured LTUG cable with earth connection. (SD-194)

Supply and providing cable end termination of 3½ x 240 sqmm PVC LTUG Aluminium armoured cable with necessary aluminium cable sockets by crimping etc. with electrical connection complete (DATA-22)

Design, Supply, Testing of 630A / 400A, 36kA, 3L+100% N, Sandwich type Aluminium, Straight feeder (Rising Main), insulation class F (155oC), Dust and Vermin proof made up of Hot galvanised Sheet Steel painted, with necessary angle iron supporting of Rising mains.Reference standard: IEC 61439-6. Reference ambient temperature: 40 °C, Protection degree: IP55. Thickness: 1.5 mm, No of conductors: 4. Painted: RAL 7035 . Halogen Free, The insulation between bars is ensured by a multi sheath made with PET film class F(155°C). (Quotation enclosed)

Supply of End Feed Unit and 4P 400A 36kA (Ics=Icu=100%) MCCB with Rotary Handle, Phase Barrier and spreader (Quotation enclosed)

Supply of Flange End Unit. (Quotation enclosed)

Supply of End Cover for the rising main. (Quotation enclosed)

Supply of Internal fire barrier for the rising main. (Quotation enclosed)

Supply of 4P 160A 36kA (Ics=Icu=100% ), Tap off Box with MCCB with RotaryHandle, Phase Barrier. (Quotation enclosed)

Supply of Rigid Support for rising main. (Quotation enclosed)

Supply of Spring Hanger for rising main. (Quotation enclosed)

Supply of Wall hanger for rising main. (Quotation enclosed)

Installation, testing and commissioning charges for rising main (Quotation enclosed)

Supply, fabrication, erection ,testing, commissioning and handing over of 13 persons capacity gearless passenger lift with Machine room as per IS 14665 with latest amendments with the following specifications 1) Location:VVIP GUEST HOUSE in Madurai Bench of Madras High Court Campus. 2) No of lift: 1 No. 3) Type of lift: Passenger lift 4) Capacity of lift: 13 persons capacity:884 kgs 5) Speed: 1.0 mtr/sec 6) Type of Drive: Microprocessor based VVVF drive 7) No of floors: Ground +4 floors 8) Total travel: 13.2 mtrs(approx.) 9) Design of lift car: Stainless Steel 304 grade 10) Position of machinery: Directl above the lift well-geared 11) No. of landing entrances: 5 (ground + 4 floors) 12) No. and position of car entrance: one in front only 13) Type of car entrance position: power operated central opening sliding door-stainless steel

29) Special features: a) Stainless steel 304 grade handrail in car b) Vandal proof SS button with SS cover c) over load warning indicator with audio announcement d) call register signal and vf operator e) Digital position indicator in car and landings f) false ceiling in car 30) other standard features: over speed governor, phase failure and phase reversal alarm bell, t guide brackets for car and counter weight, rubber padding under winding unit. Motor of adeuate capacity, electromagnetic brake with compression springs car safety gears buffer, electomechanical door locks emergency key , side supporting angles motor over load protection devices final limit switch main suspension ropes, counterweights lifting joint joist for mounting the machineries 31) Scaffolding and Civil works are included in the scope.32) Guarantee:for the materials & workmanship of equipments complete should be offered by lift firm for a period of not less than one year 33) Supply of operation and maintenance manual with necessary tools for operation 34) Lift license:preparation of drawing pament of charges to ceig and insurance policiess if any and obtaining CEIG safet certificate as per lift act rules. (KONE / OTIS / JOHNSON) (SR)

Supply, installation, testing, commissioning and handing over of 250 KVA diesel generator set 0.8 P.F, 3 ph, 415v / 420 volts, 50 c/s, 1500 RPM as detailed below.A. Engine : Water cooled diesel engine suitable for generator application with a shaft output of 310 BHP suitable at 1500 RPM under NTP conditions as per BS 5514-DIN-6271/IS 10002/ ISO - 3046 The engine shall comprise the following standard scope of supply : (Make Kirloskar Green)1) Dry type Air cleaner. 2) Expansion bellow. 3) Radiator, radiator fan and mounting. 4) Air to air charge cooler. 5) Exhaust gas turbo charger.6) Lube oil cooler and lube oil filter. 7) Fuel filter (pre and micro) 8) In-Line mono-block fuel injection pump with governor and fuel feed pump. 9) Electronic governor. 10) 24V battery charging alternator.11) 24V Volt electric starter motor. 12) Engine test certificate. 13) Residential Muffler. 14) Fly wheel with Housing 15) Exhaust silencer.Safety system of Engine : The engines shall trip for the following conditions with Visual alarm device. 1. Low lubricating oil pressure. 2. High water temperature. 3. Vee - belt failure and over speed.

8) Fuses with fuse link 2A, 4A & 10A - 10 Nos 9) Control Terminals 4.0 sqmm - 36 nos (make : Elmex / Phonix / Connect well / Equivalent)10) No Elements 6A - 2 Nos (make : Teknic / Esbee / Equivalent)11) Speed POT 5K, ohm 3W (make : Pankaj / Potel / Equivalent)12) Plug in type relays with base 24v DC, 1C/0 - 7 Nos (make : OEN / PLA / Equivalent) 13) Relays with Base 230 VAC, 5A (make : OEN / PLA / Equivalent)14) MCB / Fuse 1 pole, 32A, B-curve, 10KA / 32A (make : Schneider / ABB / Legrand / Equivalent)15) Hooter, Electronic Solid state 24V DC (make : Mimic / Acme / Hella / Equivalent)17) Control cables 1.5 / 2.5 / 4.0 sqmm Cu. Mulltistranded - 1 set (make : Finolex / RR / Polycab / Equivalent)18) GCU connectors 2 way, 4 way and 24 way with mate in lock - 1 set (make : Molex / Minifit / Equivalent) 19) Mating plugs - 1 set (make : AMP / TPK / TYCO / Equivalent) 20) Current transformer 400/5A, CL 1.5VA - 3 Nos (make : Kappa / AE / IMP / AMOL / Equivalent) 21) HRC fuse Base HB 800 and fuse link HN 400A - 6 Nos. (make : L&T / C&S / Siemens / ABB / Equivalent)22) Power contractor 4P AC duty with wide band coil, 2 No + 2 NC auxillary contacts - 2 Nos. (make : L&T / C&S / GE / Schnieder / Equivalent)23) BUSBARS - 1 setFor Phase : 40 x 10mm Aluminium For Neutral : 40 x 5mm Aluminium For Earth : 25x5mm AluminiumNote : 1. The control panel should be complete with necessary fuses, cables, labels, other accessories with neutral isolation arrangements.

2. The engine should trip for the following conditions with Audio and Visual annunciation a. Low lubricating Oil pressure b. High water / coolant temperature c. Engine over speed d. Low fuel level e. Engine under speed f. Low water / coolant level in radiator g. Under voltage h. Over voltage i. Under frequency j. Over frequency3. Audio and visual indication arrangements for :a. Low lubricating Oil pressure b. High water / coolant temperature c. High canopy temperature d. Low Battery voltage e. Charging alternator failure f. Low fuel level 4. Two line display parameter for a. Engine status b. Engine oil pressure5. The controller has data login facility for 50 faults recorded & option for RS232 / RS485 for remote monitoring / BMS Integration c. coolant temperature d. Canopy temperature e. Fuel level indication f. Battery voltage:g. Battery cranking voltage h. Engine rpm. i. Main voltage (phase - Neutral, phase - phase) j. Main frequency k. Main voltage (phase - Neutral, phase - phasel. Generator current (Amps) m. Generator frequency n. Power factor o. KVA p. KVAR q. KWHr r. KW

d) ACOUSTIC ENCLOSURE : Acoustic enclosure shall be powder coated and fabricated of 16 SWG CRCA MS sheet. The silent canopy shall be of nut bolt type construction. Critical processed of punching are done on CNC machines to maintain dimensional accuracy of hole within 0.1mm powder coating done after seven-tank surface preparation process of sheet metal. Canopy panel and doors shall have inside lining of FIRE-RETARDANT 64kg/m density mineral wool of 100mm thickness as acoustic material. Four hinged doors shall be provided to canopy. The average sound level at 1 Mt. distance shall be less than 75DBA average or as per CPCB norms.SURFACE TREATMENT - PAINTING The enclosure shall be suitably treated for degreasing, de-rusting and posphating. The canopies are passed through seven-tank treatment thoroughlyADDITIONAL FEATURES OF CANOPIESCanopy fabricated on CNC machines with dimensional accuracy of 0.1mm so as to increase its durability. Special designed supporting rips / structures are used in canopies so as to give studiness and to reduce the vibrations of the DG sets if any.WORLD CLASS COOLING PACKAGE :Canopies shall have cooling package for which it can also perform at 45 deg c / ambient temperature. No grounding required on the ground, only a level surface capable of with standing the DG weight. Lifting hooks shall be provided for the acoustic enclosure, which should be unloaded independently of the DG set. The Gen set frame shall also be provided with hooks for unloading.TEMPERATURE RISE INSIDE THE CANOPY :Canopies shall be designed so as to maintain the temperature difference between ambient and air inlet at cleaner within the enclosure well with in 5-7 deg centigrade.e) BASE FRAME :Base frame should be fabricated in sheet metal. The base frame is rugged in construction and designed for mounting engine and brush less alternator closely coupled, with cross members mounted on AVM. The base frame shall have provision for mounting of acoustic enclosure on it. The supply of Gen set includes loading, unloading and transportation charges.f) FUEL TANK :

f) FUEL TANK :460 Lts. Integral Built in Fuel Tank shall be fabricated out of 14 SWG CRCA MS sheet and its part of base frame. It is duly painted and fitted with inlet and outlet connections and mechanical fuel gauge. g) BATTERY :2 Nos 12 V 180 AH battery.h) Supply of maintenance manual books with engine and alternatore parts list.i) Supply of tools required for the maintenance and operations of the Generator set.J) Mounting of starting batteries of 1/2" thick hylem sheet base with suitable angle iron frame work support on the floor by the side of generator set to conform to latest CEIG conditions.k) supply and laying of annunciation cable of suitable capacity and length between engine and the control panel of the generator set. (SR)

Providing suitable concrete foundation with cement concrete 1:2:4 of with sand cushion all around the foundation and erection of generator set with proper alignment over the existing foundation.

Supply erection, testing and commissioning of 1.5 TR (4500 K.cal/Hr) ABS Plastic Split type inverter Air conditioner conforming to IS 1391 (Part-2) 1992 with Amdt No. 1 to 2 fitted with rotary compressor operating on non CFC refrigerant suitable for wall mounting for operation on 230V, 50HZ single phase AC supply with star rating of 5 star as per BEE specification and capable of performing the functions of

Cooling

Dehumidifying

Air Circulating

Filtering

The installation works for the above split type AC units includes the following.

1.Mounting / Fitting Indoor and outdoor units at their respective locations.

2. Laying refrigerant pipeline of required length connecting not exceeding 3 metre distance and both units after drilling hole/holes in the wall if required.

3. Insulating the suction pipe with expanded polyethylene foam 5mm tubing.

4. Laying 25mm dia flexible PVC drain pipe to throw out the condensate water being formed within the indoor unit.

5. Leakage testing the entire system unit.

6. Charging refrigerant gas in the unit.

7. Suitable electric wiring to be provided with 2.5 Sq.mm PVC insulated copper wire between indoor and outdoor units up to 6 Mtrs length and up to switch within 3 Meters of location of indoor unit (Carrier/Daikin/Bluestar/O General). (SR)

Supply and Installation of 4 KVA Electronic Voltage stabilizer (V-guard make model ID4 Ace 5540) with input voltage range 140-280V and output voltage range 200-240V with high and low voltage cut of 3 min time delay relay with demonstration. (SR)

Supply erection, testing and commissioning of 2 TR (6000 K.cal/Hr) ABS Plastic Split type inverter Air conditioner conforming to IS 1391 (Part-2) 1992 with Amdt No. 1 to 2 fitted with rotary compressor operating on non CFC refrigerant suitable for wall mounting for operation on 230V, 50HZ single phase AC supply with star rating of 5 star as per BEE specification and capable of performing the functions of

Cooling

Dehumidifying

Air Circulating

Filtering

The installation works for the above split type AC units includes the following.

1.Mounting / Fitting Indoor and outdoor units at their respective locations.

2. Laying refrigerant pipeline of required length connecting not exceeding 3 metre distance and both units after drilling hole/holes in the wall if required.

3. Insulating the suction pipe with expanded polyethylene foam 5mm tubing.

4. Laying 25mm dia flexible PVC drain pipe to throw out the condensate water being formed within the indoor unit.

5. Leakage testing the entire system unit.

6. Charging refrigerant gas in the unit.

7. Suitable electric wiring to be provided with 2.5 Sq.mm PVC insulated copper wire between indoor and outdoor units up to 6 Mtrs length and up to switch within 3 Meters of location of indoor unit (Carrier/Daikin/Bluestar/O General). (SR)

Supply and Installation of 5 KVA Electronic Automatic Voltage Stabilizer V- GUARD make VND 500 Model with Input Voltage range of 150Volt - 285Volt and Output Voltage range 200Volts to 230 Volts with High and Low Voltage cut off and 3 minutes time delay relay with demonstration. (SR)

Supply and fixing of MS stand for fixing Outdoor unit. (SR)

Supply and laying of 5/8" and 3/8" copper refrigerant pipe of 0.8mm thick with 2.5sqmm 3 core chord between indoor and outdoor unit. (Extra beyond 3 mts/AC unit) (SR)

Supply and fixing of Water Drain Pipe line (1" PVC Pipe) (SR)

Supply and erection of 50 KVAR 440Volts 50Hz 3 Phase automatic power factor correction panel, six stages, (at 0.95 lag), made up of powder coated, 16 SWG CRCA sheet steel enclosure with suitable x 1/2" AI Frame work and concreting foundation with 100A TPN MCCB as incoming (L&T/ABB/C&S) with Delta Connected capacitors (BCH/EPCOS) MOO Type operating in multiple stage with 3 current and Voltage Transducers (CVT) at the phases simultaneously to activate the desired power factor switching time between steps 120 seconds, switching off time in case of fault 3seconds with a LCD display to show the following Parameters.

a. Vr – R phase Line Voltage b. Vy – Y phase Line Voltage c. Vb – B phase Line Voltage d. Ir – R phase Line current e. Iy – Y phase line current f. Ib – B phase Line Current g. KW – Present Kilo Watts h. KVAR – Present KVAR Demand i. KVA – Present KVA j. PF – Present Power Factor k. Number of Capacitor bank ON/OFF l. Provision to indicate the imbalanced load

m.Provision to indicate the change in phaseSequence n. The APFC Panel Should have built in protection for current imbalance.

For highVoltage/Low Voltage cut off, single phase Preventer, provision for inductor coil to cater the in-rush currents, line surges, Current Limiters, Current Sensor, etc., with connection complete and as per the relevant IE Rules. Six Stages of Automatic Power Factor control panel with necessary connection. Make. (MICRO / EPCOS /or equivalent)

Stage wise details: I) Stage : 2 KVAR II) Stage : 3 KVAR III) Stage : 5 KVAR IV) Stage : 10 KVAR V) Stage : 15 KVAR VI) Stage : 15 KVAR

Earthing as per the ISI specification with an earth electrode of 2.1mt class 'B' GI pipe of dia not less than 40mm, with copper earth plate of size 125mm x 50mm x 6mm, with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry. (SD-233)

Earthing as per PWD standard with an earth electrode of 2Mtr Class 'B' GI pipe of dia not less than 32mm complete with necessary masonry work. (Radio-3Nos & EI - 2Nos) (SD-234)

Supply and run of 25mm x 3mm tinned copper flat with necessary clamps/supports on wall/floor/ground for earth connection. (SD-76)

Supply and Run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth connection. (SD-458)

supply and fixing of 65 mm dia. (2 -1/2") GI pipe (class B) of 6 metre length with 300mm x 300mm x 6mm MS base plate duly welded at the bottom with concreting with construction of masonary pedestal with suitable SMC box with door arrangement to house 6A SP MCB switch, 2/4 way connector on suitable hylem sheet and supply and fixing of 48W LED street light fitting with LED (Higher end) with 1metre 32mm dia. GI pipe (class B) Complete with suitable MS clamps for LED street light fitting and SMC box with PVC unsheathed copper leads from SMC box to fitting and with painting of suitable colour. (SD 543)

Supply and clamping of 4 x 16 sq.mm PVC aluminium LTUG armoured cable in suitable dia Class B G.I pipe on post or on wall with MS Clamps. (for street light post) (DATA-23)

Supply and laying of 4 x 16 sq.mm PVC armoured aluminium LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 mt. Layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good. (For Street light post) (SD-203)

Supply and fixing of brass cable gland for 4 x 16 sq.mm. PVC LTUG armoured cable with earth connection (DATA-24)

Preparation of Site plan, physical layout electrical schematic diagram (6 Sets) getting drawing approval from CEIG, preparation of completion report rectification report etc. arranging CEIG inspection, paying CEIG inspection fees, obtaining safety certificate from CEIG and preparation of 1 set of approved drawing and a copy of safety certificate in a neat frame work to be fixed in panel room.

Supply and installation of 30W Wall Mount speaker with suitable wall mount bracket (Higher End). (Pre.TS Andipatti Court)

Supply and run of 2 core 1.5sq.mm Shielded copper speaker wire in existing PVC rigid pipe concealed in wall and ceiling. (Higher End) (Pre.TS Andipatti Court)

Supply and run of XLR Professional Microphone Cable in existing PVC rigid pipe concealed in wall and ceiling. (Higher end) (Pre.TS Andipatti Court)

Supply and installation of 240W PA Mixer Amplifier (Higher End).(Pre.TS Andipatti Court)

Supply and installation of UHF Cordless Handheld / Tie Clip / Neck Band Microphone system.(Higher End) (SR)

Supply and installation of Studiomaster SVC1000/ Eq 1 kVA Voltage stabilizer Specially designed for audio equipment. with Wide input voltage range for Indian conditions (180-250V), High overload capability, Short circuit protection., Less than 1 sec stabilization time, No waveform distortion, Low-noise operation, Accurate voltage control, Over and under voltage correction (automatically regulates in both conditions), Generator compatible, Voltmeter displays output voltage so no more 'drop' during bass thump.(Pre.TS Andipatti Court)

Supply and fixing of 25mm PVC rigid pipe concealed in wall and ceiling and making good of the concealed portion with suitable colour.(Pre.TS Andipatti Court)

Supply and run of CAT-6 Unarmoured LAN Cable (Higher End) in existing PVC rigid pipe.(Pre.TS Andipatti Court)

Supply and erection of 2 kVA online UPS (Single Phase In & Single Phase Out) System with suitable SMF Battery arrangements with rack to provide minimum 2 hours back-up (For Intercom, LAN and CCTV) (SR)

Supply and fixing of 12U Rack with accessories and fan with suitable angle iron frame work. (Higher End) (SR)

Supply and fixing of 4U Rack with all relevant accessories. (Higher End) (SR)

Supply and installation of 50 inch Samsung BU8000/ Eq. 4K UHD Smart TV LED Television with suitable wall mount accesories, 5 Meter 4K HDMI Cable and Wireless Mouse. (Pre.TS Andipatti Court)

Supply and installation of V-Guard Make/Eq TV Voltage Stabilizer for 140cm (55") TV + Set Top Box +Home Theatre System(Working Range:90-290V;3A).(Pre.TS Andipatti Court)

Supply and run of 3 core 1.5sq.mm PVC power cable of 1100V grade in existing concealed PVC rigid pipe. (Higher End) (Pre.TS Andipatti Court)

Supply and fixing of 5A / 15A 3 pin combined flush type wall socket with 15A flush type switch concealed in suitable MS box flush with wall with painting. (SD137)

Supply and fixing of Honeywell/ APC/ Belkin Make 4 Socket 2 Meter Surge Protector.(Pre.TS Andipatti Court)

Supply, fixing and termination of RJ-45 I/O Socket for LAN with CAT 6 Module, Single Socket RJ-45 Face Plate and 2 Metre Length Patch Cord. (Higher End) (Pre.TS Andipatti Court)

Supply, fixing and termination of 16 Port un-managed 10/ 100/ 1000 LAN Network switch in existing Rack with accessories (Higher End) (SR)

Supply, fixing and termination of D-Link/ TP-Link/ Intellinet Make 16 Port CAT6 Patch Panel Fully Loaded.(Pre.TS Andipatti Court)

Supply and fixing of 1 Meter Patch cord.(Higher End) (SR)

Supply, installation, configuration and commissioning of NEOS Syntel/ Accord/ Matrix Make EPABX Base unit with 48 Analog Extensions and 4 Trunk Lines.(Pre.TS Andipatti Court)

Supply and fixing of Beetel/ Panasonic Make Push Button Telephone with Caller ID. (Pre.TS Andipatti Court)

Supply, fixing and termination of RJ-11 I/O Socket for Telephone with Single Socket RJ-11 Face Plate and CAT 6 PVC Module Box. (Higher End) (Pre.TS Andipatti Court)

Supply, fixing and termination of Standard Make 20 pair MDF Box with module and Krone.(Pre.TS Andipatti Court)

Supply, fixing and termination of Standard Make 100 pair MDF Box with module and Krone. (Pre.TS Andipatti Court)

Supply and run of 2 pair unarmoured 0.5mm Telephone cable (Higher End) in suitable PVC rigid pipe Concealed in wall and ceiling and making good of the concealed portion with suitable colour. (Pre.TS Andipatti Court)

Supply and run of 20 pair unarmoured 0.5mm Telephone cable (Higher End) in suitable PVC rigid pipe Concealed in wall and ceiling and making good of th1 concealed portion with suitable colour. (Pre.TS Andipatti Court)

Supply and run of RG - 06 Coaxial cable in existing PVC Rigid Pipe on wall and ceiling. DATA-R13

Supply and run of 1 of No.8 SWG GI wire for earth connection.SD-74

P KALIKURICHI (BID ID -1070160)