General Fund 2025 - 26 Construction of Office Rooms working Area for Sanitary Officers in Aralvoimozhi Town Panchayat office campus .

Amount

Earth work excavation and depositing on the bank with initial lead and lift of 10 metres and initial lift of 2 metres in hard stiff stiff clay stiff block cotton hard red earth murram, gravel stoney earth and earth mixed with small size boulders and hard gravelly soils (SS 20 B) etc., complete as per standard specification

Plain Cement Concrete 1:4:8 (One Cement, Four Crushed Stone Sand and Eight aggregate) mix using 40mm ISS HBG metal including cost and conveyance and all labour charges etc. complete.

Refilling with excavated soil (other than sand) complying with standard specification for filling in foundation and basement.

Supplying and erecting steel centering for sides and soffits including supports and strutting upto 3.29 m height for plain surface as RCC slabs, rectangular tee (or) elbeams, lintel, bed block stair case waist slab, landing slab, etc., complete as per standard specification - 10m2 as per TNDSS & Morth specification No:30 & 36

Supply and fabricating and placing in position of steel Reinforcement using Mild steel of Ribbed tor steel rods for all RCC works as per the design given by the department officers including cost of steel and binding wire and all labour charges for cutting bending and tying and placing in position etc., complete as per SS

Reinforced cement concrete 1:11/2:3 (one cement one and half Crushed Stone Sand and three aggregate) using 20mm size I.S.S. metal including cost conveyance of materials to site and all labour charges etc., mixing laying consolidating curring etc., but excluding cost of steel etc., complete as per standard specification as per TNDSS NO: 30 V,VI (S3) VII-3

Brick work in cement mortar 1:5 mix using (One cement and five Crushed Stone Sand) using best quality of III class Country bricks of size (8 3/4"x4 1/4"x 2 3/4") for foundation including curing cost and conveyance of all materials to site and all labour charges etc., complete as per standard specification TNDSS specification No.31 & 31C- 10m3

Plastering with cm 1:3 mix (One Cement and Three Crushed Stone Sand), 10mm thick cost and conveyance of all materials finishing, curing and all labour charges etc complete as per standard specification.

Plastering with cm 1:5 mix (One Cement and Five Crushed Stone Sand), 12mm thick cost and conveyance of all materials finishing, curing and all labour charges etc complete as per standard specification.

Painting two coats with ready mixed Plastic Emulsion Paint S.I.358 Plastic emulison paint of'approved quality and colour over a priming coat, including thorough scraping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required including cost and conveyance of all materials etc.and all lobour charges etc.complete as per Standard specification and as directed by the departmental officers. TNBP No:66-A (Sl.No.358)

Providing UPVC (Un-Plasticized Polyvinyl Chloride) Door: Providing and fixing casement doors fabricated from un-plasticized polyvinyl chloride (uPVC) sections. Profiles: The profiles should be three chamber system which provides high insulation properties with outer frame 60mm x 55mm with an outer wall thickness of 2.4mm.The window unit should be designed with all corner joints mitred and fusion welded. Windows should be steel reinforced with 25 x 24 x 25mm steel reinforcement with a thickness of 1mm to have dimensional stability. The sash should be of 60 x 102mm. The mullion should be of 60 x 74mm. The profiles should have co-extruded seals. Hardware: All the hardware like friction stays, handles should be screwed with self tapping screws. The handles, locks should be designed so that they cannot be released from outside. Glazing: The window system should be glazed with 5mm plain float glass / 6mm bison lam Installation: The profiles should be cut to length and welded 45 degrees. The window should be designed such that the water drainage does not pass through the reinforcement chamber. The window system should be fixed directly to the plastered brick wall using self expanding nylon plug and driving ms electroplated screws into plug.

UPVC Window Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm.The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames.

UPVC Ventilator Specification: Supplying and fixing UPVC (Un-Plasticized Polyvinyl Chloride) Louvered Ventilators of from the profile the size of outer frame 60mm x 58mm and shutter profile size of 60 x 78mm both profiles are reinforced with GI/1mm 125GSM and 100% corrosion free, the profile are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with all over the edges of frame and shutter. The corners and joints should be welded and cleaned. Radiations pin headed glass 4mm thick should be provided in the louvers. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames.

Supply and fixing of Mild steel grill works for door,windows ,ventilator etc,including redoxide priming coat and cost of materials and all labour charges etc.complete

Solid PVC Door Shutters using 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC Sheets. Shutter using 5mm thick solid PVC Sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x30mm. The over all size of top rail, lock rail and bottom rail shall be 75mm x 30mm.The over all size of frames shall be 50mm x 45mm with suitable rabate for housing the shutter

Paving the floor with Plain/Design Ceramic tiles ( Colour and shade as directed ) of Stain Free Nano Polish Vitrified Tiles of size 600 x 600 x 8mm in all floors over a base layer of cm 1:3 mix 20mm thick laid in situ and pointed with same coloured cement ( white cement mixed with colouring pigment ) neatly and fixed in position so as to make it perfectly smooth and shining,to the alignment etc.complete complying with standared specifications and as directed by the departmental officers. The sample colour and shade of the ceramic tiles should be got approved from the departmental officers before use in the works - 10m2.

Dadooing with glazed tiles of 300mm*200mm*6mm size of approved quality and colour set in c.m 1:2mix (one cement and two sand) 10 mm thick and pointing with white cement using 0.4 kg /m2 neatly as directed -including cost of all materials and labour charges etc complete as per SS

Wiring with 2x1.5 sqmm PVC unsheathed Sc. Cu. conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories with TW switch box and 5A F.T. switch in fush with wall with 3mm thick hylum sheet cover for making good of the coneal3ed portion with suitable colour for PVC concealed light point (For electronic regulator). SD 23 (light point)

Wiring with 2 x 1.5sqmm (22/0.3) PVC insulated SC unsheathed Cu. conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories, in flush with wall, wtih 150mm x 100mm x 113mm TW switch box with 3 mm thick Hylem sheet cover for 5A 3 pin non inter locking CS Plug with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour for concealed PVC plug point. (SD 38)

Supply and fixing of 1200mm (48'') sweep AC ceiling fan complete with stepped electronic 300w regulator with one metre down rod on the existing clamp (SD.107)

Supply and fixing of 20W 4 Feet LED Fitting with LED complete with TW round blocks on wall or ceiling with LED tube with PVC unsheathed Copper leads from terminals to the fitting. (SD 446)

Supply and fixing of WT bulk head fitting with guard suitable for 15 W LED Bulb including all charges etc. complete.(SD.83)

Supply and fixing of TNEB meter board suitable for 32A single phase service connection with 32A fuse unit(500V) 32A neutral link and earth link (1"x1/8"copper flat) on TW plank of size 375mm x 300mm x 19mm with supporting TW reepers of 1" thick an either side with painting with suitable bolt and nuts for fixing the TW plank on wall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit with 1No 40 Amp 30 MA Double Pole RCD / RCCB (Higher End) with suitable necessary connection.SD 125

Supply and run of 2 x 1.50sq.mm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade in 25mm dia GI pipe (Class 'B') suitably bent at both ends with necessary angle iron up right and end supports for mains. SD 69

Supply and run of 2 x 1.50 sq.mm (22/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V on 7/20 GI bearer wire for service connection mains. SD 64

Supply and fixing of 16A TPN metal clad switch on suitable angle iron frame work with MS cable entry boxes with earth connection only.SD 146

Supplying and fixing in position colour Europen water closet with low level flushing tank of 10 lit capacity of best quality and approvel make with 100mm 'p' or 's' trap with double flapped rigid PVC seat cover with CP brass etc. Complete complying with standard specifications and as directed by the department officers ( EWC should got approvel by the executive work before use on work.)

Weathering course with concrete brocken brick jelly 20mm size in pure slacked lime (no sand to be added) over roof slab the proportion of brick jelly to lime being 32 to 12.5 well beaten with wooden beaters for giving required slope and thickness as directed by the departmental officers.

Dadooing with glazed tiles of 300mm*200mm*6mm size of approved quality and colour set in c.m 1:2mix (one cement and two Crushed Stone Sand) 10 mm thick and pointing with white cement using 0.4 kg /m2 neatly as directed -including cost of all materials and labour charges etc complete as per SS

Terrace flooring with Hydraulic pressed tiles of size 20*20*2cm laid in c.m 1:3 (one cement three sand) mixed with crude oil 10 %, by weight of cement and pointed with same oiled mortor etc complete as per SS

Providing and fixing 6" dia PVC rain water down fall pipes with necessary PVCshoes, pvcbends, other specials clamps, screws, nails, teekwood plucks etc, complete including cost of all materials and labour charges as per SS. for 110mm dia pipe 4 kg. per cm2

Supply and fixing of Wash Hand Basin of size 550mm x 400mm with all accessories such as Cast Iron Brackets, 32mm dia CP Waste Coupling, Rubber Plug and Chain, 32mm dia 'B' Class GI Waste Pipe, 15mm dia GM Wheel Valve, 15mmdia Nylon Connection, 15mm dia Brass Nipples, 15mm CP Pillar Tap etc

Supply and delivery and fixing of HDPE Tank as per IS 12701/1996 Including loading ,unloading ,transportation, and labour charges for fixing of GI pipes and specials for pipe connection works including cutting ,threading and fixing charges etc.(WD-M 1418)1000 LITERS

Painting two coats over new iron work with ready mixed paint of apprved quality and colour including cost of all materials and labour charges etc complete as per SS

M S P CONSTRUCTION WORKS (BID ID -1551268)