GESU 05 2022 23 SPECIAL REPAIR TO BLDG NO P-11 OVERHEAD PASSAGE STATIC WATER TANK REPAIR EXTENSION OF HARDSTANDING AND PROVN OF SHEETING UNDER GE SOUTH UDHAMPUR

Amount

Demolition cement concrete in ground floors and paving ( unreinforced ) n.exc. 15 cm thickness ( below or above ground floor) complete all as specified and as directed.

Dismantling wall and ceiling boards (fibre,pulp, insulation etc) or insulation boards any thickness including cover fillets complete all as specified and as directed.

Dismantling floor, hearth or wall tilling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish of the premises complete all as specified and as directed.

Demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pilars, etc but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed.

Demolition of reinforced cement concrete as in shelves, roof, floor (other than ground floor) beam, staircase, landing chajja and similar suspended work (reinforcement cut as required to facilitate demolition) complete all as specified and as directed.

Brick work with sub class 'B' bricks straight or curved on plan exc. 6.00m mean radius built in cement mortar 1:6 complete all as specified and as directed.

Brick work with sub class 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and as directed.

PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs etc complete all as specified and as directed.

Material and labour for providing Reinforced Cement Concrete design mix M-25 using 20 mm graded aggregate as in slabs supported on walls, beams and columns in floor, roof, landing, balconies, conopies, decks, slab and in shelves and like complete all as specified and as directed.

Formwork to soffits of suspended flat slabs such as roof slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and as directed.

Mild steel TMT bars 10mm dia and over in reinforcement, cut to length, bent to shape required including cranking, bending spirally or hooping for columns, hooking ends and binding with Mild Steel wire (annealed) not less than 0.9mm dia complete all as specified and as directed.

All as per srl item No. 11 above but 5mm dia and over including 10mm dia in stirrups, spacers and binders etc complete all as specified and as directed.

Rendering 10 mm thick on fair faces of brick /concrete surfaces in cement mortar 1:6 and finished even and smooth without using extra cement complete all as specified and as directed.

Rendering 05 mm thick CM 1:4 on fair surfaces of ceiling work and finished even and smooth without using extra cement complete all as specified and as directed.

Rendering 15mm thick in CM 1: 4 on fair faces of brick work or concrete surfaces for backing coat for tiles complete all as specified and as directed.

Glazed coloured ceramic tiles in vertical surface 300mm x 600mm x 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the surface complete all as specified and as directed.

Hardcore of broken stone or boulders of gauge not exc 63mm and deposited spread and levelled in layers not exc 15 cm thick watered and rammed to a true surface complete all as specified and as directed.

75 mm thick cement concrete (1:4:8) type D-2 (using 40mm graded crushed stone aggregates) as in sub base to floor complete all as specified and as directed.

25mm thick cement concrete 1:2:4 type B-0 using 12.5mm graded crushed stone aggregates as in floor and finished even and fair complete all as specified and as directed.

15mm thick screed bed or bedding layer in cement mortar 1:4 for laying floor finishes complete all as specified and as directed.

Non-skid coloured ceramic tiles (square/rectangular) 7 to 8 mm thick, area of each tile exc 0.11 sqm but not exc 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface complete all as specified and as directed.

Screed bed or bedding layer of mortar 20mm thick in cement mortar 1:4 laying floor finishes complete all as specified and as directed.

Dura stone tiles of size 305mm x 305mm x 10 mm thick as in floors set and jointed in neat cement slurry and pointed in coloured cement to match the surface of tiles complete all as specified and as directed. ( Note :Shade/colour as approved by GE)

Double charged vitrified ceramic tiles, area of each tile exc 0.36sqm but n.exc. 0.42 Sqm, 10mm thick (square or rectangular) of superior quality as in floor and walls surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match the light shade of tiles complete all as specified and as directed.

All as per item No. 24 above but on dado/skirtings complete all as specified and as directed.

75 mm thick plain cement concrete, (1:3:6) type C-2 (using 40 mm graded crushed stone aggregates) as in plinth protection complete all as specified and as directed.

Taking down cement plaster and raking out joints, hacking for key, scrubbing down with water built in cement mortar any description complete all as specified and as directed.

Rendering 15 mm thick on fair faces of brick work in CM 1:6 finished even and smooth without using extra cement complete all as specified and as directed.

Preparation of new plastered or un- plastered surfaces and walls including cornices, pillasters etc and applying two coats of Acrylic emulsion paint over a coat of primer complete all as specified and as directed.

Applying one coat birla wall care putty on newly plastered wall surfaces including preparation of surface by brooming down or steel wire brushing, scrapping down vegetation growth, efflorscent salts and trading oil and greasy spot complete all as specified and as directed.

Applying two coats of Acrylic emulsion paint on old plastered surfaces complete all as specified and as directed.

Two coats of distemper oil emulsion over a coat of primer including preparation of new plstered surfaces of walls complete all as specified and as directed.

Two coats of distemper oil emulsion including preparation of old plastered surfaces of walls complete all as specified and as directed.

6 mm thick non asbestos fibre cement building designer boards or tiles fixed in ceiling of size 600mm x 600mm panel confirming to IS 14862, including anodised aluminium snap grid frame work with size of grid 605 mm x 605mm for seamless ceiling comprises of aluminium perimeter l section members, including fixing with 4mm thick GI wire adjustable suspenders including all accessories complete all as specified and as directed.

Taking down chowkats or frame with shutter (without taking off shutter from frame) exc. 1.5 sqm but n.exc 4 sqm each complete all as specified and as directed.

Taking down chowkats or frame with shutter (without taking off shutter from frame) n.exc 1.5 Sqm each complete all as specified and as directed.

Aluminium powder coated frame suitable for sliding/openable/fix, partition, doors, windows, ventilator, guard bar, grill and similar work with one or more rebates including joining cleat for fixing etc complete all as specified and as directed.

Aluminium powder coated door shutters, aluminium section weighing 0.55 Kg/m including necesssary joining cleats, glazing clips, rubber neoprene packing handles 2 Nos in each door hinges, sliding bolt and tower bolts anodised aluminium snap beading screws etc complete all as specified and as directed.

Powder coated aluminium anodised window and ventilator shutters, side hung type without sash bar, aluminium section weighing 0.55 Kg/m including necessary jointing cleat glazing clips, rubber packing, anodised aluminium snap beading screws etc. including all fittings complete all as specified and as directed.

Sheet glass ordinary quality 5 mm thick (tinted/one side view glass) in squares n.exc 0.5 sqm each pane and glazing including all fitting complete all as specified and as directed.

Supply & Fixing 10mm thick toughened glass as in railing fixed type including necessary fixings such as silicon gell or other fixing clips clamps, complete all as specified and as directed.

Aluminium mortice lock vertical type, size 100 mm brass 4 lever etc complete all as specified and as directed.

Double action floor sprig hydraulically regulated made up of min 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel covering pivot made of brass, other parts made of mild steel heavy duty complete all as specified and as directed.

20mm thick granite (of any type) machine cut as in shelves etc laid over cement backing coat and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and as directed.

Sand cushioning/filling under floors for laying interlocking tiles complete all as specified and as directed.

Machine pressed precast concrete interlocking paver blocks lacquer finish any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 grade with grey cement and pigment complete all as specified and as directed.

Backing coat of cement mortar 15mm thick in 1:3 to receive tiles in vertical surfaces complete all as specified and as directed.

Wall cladding colour designer tiles of size 300mm x600mm x 7mm thick (shade as approved by GE) set and jointed in neat cement slurry and laid over screed bed/backing layer of 10mm thick in cement mortar and pointed in white/coloured cement to match the colour of tiles as on vertical surfaces such as dado/skirtings complete all as specified and as directed.

Taking down aluminium door/window shutters form frame repair to shutter and frame and making good and serviciable and refixing to existing frame including fixing to rubber kit, handle, and similar items etc complete all as specified and as directed.

Stainless steel pipes as in framing for fixing of railing including fixing of 10mm thick toughened glass on frame as per site requirement conforming to Gde 304, complete all as specified and as directed. (Note : Toughened glass will be measured and paid separately).

PVC moulded door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specification complete all as specified and as directed.

Supply and fixing factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top and bottom rail. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail ; panelling of plain colour PVC sheet to be fitted in the M.S frame welded/sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, suppling & fixing in the frame at site as per specification complete all as specified and as directed.

Butt hinges, 100 mm size extruded aluminium alloy with galvanised mild steel hinge pin, anodised complete all as specified and as directed.

150mm long Aluminium anodised barrel tower bolt of extruded section complete all as specified and as directed.

150 mm length Aluminium handles fabricated type anodised complete all as specified and as directed.

Sheet glass 3mm thick ordinary quality and glazing with oil putty in square n.exc 0.5 Sqm in each pane up to G+2 height bldg complete all as specified and as directed.

4mm thick figured glass, pin headed type and glazing with oil putty or wooden beads not exceeding 0.50 Sqm in each pane complete all as specified and as directed.

Framed work such as grill, gratings, etc with ends of bars shouldered and/or riverted or forged in to spikes, framed guard bars, barred iron doors ladders framed balusters and similar work conforming to Fe 290 Gde E-165 complete all as specified and as directed.

Galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm complete all as specified and as directed.

MS 300 mm ordinary rat rail rod pattern spring including roller and roller plate complete all as specified and as directed.

Floor door stoper (140mm length) of aluminium alloy body complete all as specified and as directed.

Door closer hydraulically regulated, designation no 2 universal type suitable for door shutter of 701mm to 850 mm in width and of weight between 36 to 60 kg Aluminium (extruded section) body complete all as specified and as directed.

Prelaminated particle board of 18/19mm thick interior grade prelaminated one side with decorative choice lamination & other side balancing white lamination fixed with timber frame work of cupboards book cases etc complete all as specified and as directed.

2nd class Hard wood plain fillets square, rectangular or triangular in section clean sawn ,secured with nails or beads exc 3 sq cm but n exc 6 sqcm complete all as specified and as directed.

Hasp & staple 100mm size aluminium anodised fixed with screws complete all as specified and as directed.

Continous (Piano) hinges, mild steel, bright finished or electro galvanised width of flaps in 30mm complete all as specified and as directed.

40mm dia cupboard knobs fixed with nuts screws and washers of brass polished of approved quality complete all as specified and as directed.

Stain less steel catcher of superior quality complete all as specified and as directed.

50mm stain less steel pivoted type hinges of superior quality complete all as specified and as directed.

Sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratary with plugs washer and wastes including bedding in cement mortar to drawf wall or including fixing cantiliver brackets and connecting union to pipes overall size 915 mm x 460 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and as directed.

Water closet wall mounted pattern colour 535mm x 380mm x 400mm (colour as approved by GE) complete all as specified and as directed. Make CERA Cat Part No (S1041109 P trap,) , Seat cover B1510108 Clair seat cover

WHB coloured 550mm x 480mm with Pedestal complete all as specified and as directed. Make CERA Cat Part No (S2040115 & S2090111) (as approved by GE)

15mm bore centre hole basin mixer with round spout with 450mm long copper pipes and brass nuts with out Pop up complete all as specified and as directed. Make: Jaquar Cat Part No CON 167KNB and equvalent in CERA.

15mm bore long body Bib tap complete all as specified and as directed. Make Jaquar Cat Part No CON-037KN and equvalent in CERA.

15mm bore Bib tap complete all as specified and as directed. Make Jaquar Cat Part No CON 107KN and equvalent in CERA.

15mm bore angular stop cock with wall flange complete all as specified and as directed. Make: Jaquar Cat Part No CON- 059KN and equvalent in CERA.

Health faucet ABS body with wall hook and 1 m chrome plated PVC hose pipe complete all as specified and as directed. Make : CERA Cat Part No F8030103. and equvalent in CERA.

Chromium plated toilet paper holder complete all as specified and as directed. Make :- Jaquar Cat Part No ACN 1153N and equvalent in CERA.

Glass shelf with chromium plated guard rails complete all as specified and as directed. Make:- Jaquar Cat Part No ACN-1171N and equvalent in CERA.

600mm long brass chromium plated towel rail fancy type complete all as specified and as directed. Make :- Jaquar Cat Part No ACN-1111NM and equvalent in CERA.

Soap dish complete all as specified and as directed. Make :- Jaquar Cat Part No ACN 1131N and equvalent in CERA.

Towel rack complete all as specified and as directed. Make :- Jaquar Cat Part No ACN 1181FN and equvalent in CERA.

Double Coat hook complete all as specified and as directed. Make :- Cat Part No ACN 1161N and equvalent in CERA.

Rotational moulded polyethylene water storage tanks 500 ltrs(cylindlerical vertical with closed top) hoisted and fixed in position all as specified in SSR part I inclding dismantaling of existing damaged water tanks complete all as specified and as directed.

Rotational moulded polyethylene water storage tanks 1000 ltrs(cylindlerical vertical with closed top) hoisted and fixed in position all as specified in SSR part I inclding dismantaling of existing damaged water tanks complete all as specified and as directed.

PTMT ball valves 20 mm dia high pressure with epoxy coated aluminium rod and high density plastic ball screwed for iron pipes(Minimum weight 210 gms) and fixed to iron pipes complete all as specified and as directed.

Gun metal globe or gate valves high pressure with polythene float and fly nut complete screwed for iron pipe or for unions of 20 mm bore complete all as specified and as directed.

Taking up or down of 15/20 mm bore pipes steel tubing and connections complete all as specified and as directed.

Steel tubing galvanized, medium grade with all fittings, laid in floors or fixed to walls,15mm bore including taking down old pipe complete all as specified and as directed.

Steel tubing galvanized, medium grade with all fittings, laid in floors or fixed to walls, 20mm bore including taking down old pipe complete all as specified and as directed.

40 mm waste coupling of PTMT ( half or full threaded) (Minimum weight 60 gms) complete all as specified and as directed.

40 mm dia PVC waste pipe for sink and wash hand basin of pressure rating 10 Kgf/Sqcm complete all as specified and as directed.

PVC (SWR) Floor trap, 75 mm dia of outlet, plain with grating including jointing with solvent cement including removing old trap and making good complete all as specified and as directed.

110 Bore PVC (SWR) pipes as in repairs single socketed in any lenth with rubber ring joints fixed to walls complete all as specified and as directed.

75 mm Bore PVC ( SWR) Pipes in repairs single socketed in any lenth with rubber ring joints fixed to wall complete all as specified and as directed.

PVC (SWR) bends any radius 75 mm bore complete all as specified and as directed.

PVC (SWR) bends any radius 110 mm bore complete all as specified and as directed.

PVC connection 15mm dia and 45cm long with two Nos of PTMT check nuts and washers complete all as specified and as directed.

PVC bathroom cabinet mirror 450 mm x 350 mm (Prayag Cat Part No 557) with door fitted with looking mirror complete all as specified and as directed.

10-12mm thick gypsum boards seamless false ceiling as in ceiling plain, moisture resistant, including GI hanging wires & frames with intermediate, perimeter channel ceiling channel, along nuts and bolts connecting plates gypsum boards, dry wall screws soffits cleats, ceiling section, rowel plugs fixtures and screws and applying two coats of emulsion paint over a coat primer on exposed surface, complete all as specified and as directed. Note : (a) Design of ceiling board as approved by GE. (b) GI grid/hanging system shall be of the same make as of false ceiling manufacturer.

Roughening surfaces of old concrete surfaces by picking up, sweeping, cleaning and washing down with water to remove dust etc including taking down tarfelt and brushing neat cement slurry @ 3 kg/Sqm including 10mm thick plastering in CM (1:3) finished even and smooth mixed with water proofing compound (WPC shall be measured and paid separately). Applying bituminous primer on roof surfaces @ 0.40 ltr/Sqm and applying one coat of hot blown bitumen of grade 85/25 @ 1.20 Kg/Sqm and provide modified polymeric five layered APP (Atactic Polypropylene) Modified Polymeric Membrane with 100 micron high molecular high density polyethylene film. Min wt of membrane will be 3.5 Kg/Sqm and bonded completely to the surfaces with minimum end overlap of 15 cms and side lap 75 mm (overlaps to be bounded with thermo fused by flame) and over APP applying one coat of hot blown bitumen 85/25 @ 1.2 Kg/Sqm blinded with fine sand in dry condition @ 0.5 Kg/Sqm & including two coats of bituminous Aluminium paint, complete all as specified and as directed.

PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregates) as in PCC filling in MS chowkhat & base of water tank on roof surface complete all as specified and as directed.

Preparation of surface and applying textured painting (granular or impression type) , any colour and any position complete all as specified and as directed.

Supply only Liquid water proofing compound complete all as specified and as directed.

Dismantling AC corrugated sheet as in roof covering complete all as specified and as directed.

Dismantling framed work timber scantlings 40 sq.cm and over in section, in any position complete all as specified and as directed.

Rolled sections as in main and cross beams, hip and jack rafter, purlins where connected to common rafers and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates Fe 410-W (Gde-E-250)qualiy - A complete all as specified and as directed.

Pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick crimpted/tapard at the external end slope of any colour having tensile strength 550 Mpa as in roof covering fixed with self tapping screws and caps etc complete all as specified and as directed.

Plain galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick in ridges, hips, valley gutters at the external end slope of any colour having tensile strength 550 Mpa as in roof(ridges) covering fixed with self tapping screws and caps etc complete all as specified and as directed.

Material and labour preparation of new steel surfaces of any description over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide chrome primer complete all as specified and as directed.

4mm thick AC board (designer ceiling) of size 600mm x 600mm panel confirming to IS 14862 type B category three including GI frame work with size of grid 605 mm x 605mm for seamless ceiling comprises of GI perimeter including all accessories complete all as specified and as directed.

Screed bed or bedding layers of 15mm thick cement mortar 1:6 for laying floor finishes complete all as specified and as directed.

25mm thick PCC type B-0 (using 15mm graded crushed stone aggregates) as in sub base for receiving floor finishes complete all as specified and as directed.

Vitrified ceramic tiles 10mm thick (square/ rectangular) polished, area of each tile not exceeding 0.36 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

All as per item No 115 above but skairting/dado complete all as specified and as directed.

Material and labour glazed ceramic tiles of size 350 mm x 250 mm x 7 mm/450mm x 350mm x 7mm thick coloured tiles on vertical surfaces set and jointed in neat cement slurry and pointed in white cement mixed with colour pigments to match the existing surface complete all as specified and as directed.

Material and labour for applying two coats of birla wall care putty on new plastered surfaces of wall including preparation of surface by brooming down or steel wire brushing, scrapping down vegetation growth, efflorscent salts and trading with oil greasy spot complete all as specified and as directed.

Rendering 15 mm thick in cement mortar (1:4) on other than fair face of brick or concrete surface complete all as specified and as directed.

Applying two coats of cement based paint over a preparation of new plastered surfaces complete all as specified and as directed.

100mm long stainless steel butt hinges complete all as specified and as directed.

Aluminium handles cast type anodised 125mm long complete all as specified and as directed.

Pressed steel frame size 125mm x 60 mm for door with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc, complete all as specified and as directed.

Flush shutters 30 mm thick solid core construction, with block board core and plywood face panels, commercial type on both side complete all as specified and as directed.

300 mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and as directed.

Stainless steel wire cloth 0.45 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with aluminium staples complete all as specified and as directed.

Preparing new wooden surface & applying two coats of synthetic ennamel paint over a coat of pink primer over 10cm width or girth complete all as specified and as directed.

Supply and fixing 4 mm thick figured glass, pin head type and glazing with oil putty in squares n. exc 0.50 sqm in each pane complete all as specified and as directed.

Aluminium body heavy duty double action floor spring of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other part made of mild steel , mad suitable for glass shutter at both side rotable complete all as specified and as directed.

12 mm thick Pre-laminated particle board, exterior grade both side laminated fixed to aluminium frame work complete all as specified and as directed.

Taking up or down 20 mm bore pipes steel tubing and connections complete all as specified and as directed.

Taking up or down of 15 mm bore pipes steel tubing and connections complete all as specified and as directed.

GI pipe medium grade 20 mm bore in wall and ceiling or laying in floors, including new fittings as required at site complete all as specified and as directed.

GI pipe medium grade15 mm bore in wall and ceiling or laying in floors, including new fittings as required at site complete all as specified and as directed.

Supply and fixing as in repairs vitreous china wash basin, white, flat back size 550 mm x 400 mm, excluding taps, waste chain, plug and porcelain stopper but including brackets, flush pipe, cutting for and pinning in ends of bracket or erecting stand complete all as specified and as directed.

Supply and fixing as in repairs 10 ltrs capacity PVC valve less syphonic action type, low level flushing cistern, white, with inlet, ball valve float and handle including brackets complete all as specified and as directed.

S & F as in repairs WC Orissa pattern size 580mm x 440mm white with integral foot rest excluding flushing system including P or S trap complete all as specified and as directed.

Supply and fixing as in repairs 15 mm bore pillar tap, fancy type, cast copper alloy, with capstan head, chromium plated, screwed down high pressure, with or without letter Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe or for brass ferrule complete all as specified and as directed.

Supply and fixing as in repairs 15 mm bore bib taps, long body with wall flange with aerator fancy type chromium plated cast copper alloy with crutch or butter fly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed.

Supply and fixing as in repairs 32 mm dia PVC waste pipe complete all as specified and as directed.

PVC (SWR) gully trap 125/110 mm setting and jointing with solvent cement complete all as specified and as directed.

75 mm dia PVC (SWR) floor trap plain, with grating including jointing with solvent cement complete all as specified and as directed.

S & F as in repairs chromium plated angle valves of 15mm bore, with adjustable wall flange complete all as specified and as directed.

Dismantling of 1000 ltrs capacity water tank of any description including all connection and removing from site complete all as specified and as directed.

Supply and fixing as in repairs, ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for 20 mm bore pipe and fixed (Minimum weight 142 gms) complete all as specified and as directed.

20 mm thick makrana white marbe tiles machine cut in floor laid over cement screed and jointed with white cement slurry including cutting and polishing of type complete all as specified and as directed.

S & F as in repairs vitreous china urinals, bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1: 2 securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement fixing automatic flushing cistern with brackets, flush pipe grating and union for discharge pipe (exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and as directed.

Screed bed or bedding layers of 20mm thick cement mortar 1:6 for laying floor finishes complete all as specified and as directed.

Lacquar coated Chequered tiles 30cm x 30cm x 20-25mm thick, set jointed and pointed in neat cement slurry as in path with white cement and pigment etc complete all as specified and as directed.

Mild steel chromium plated curtain rod including brackets and necessary fitting complete all as specified and as directed.

Excavation in post holes each not exceeding 0.50 cum getting out, returning filling in and well ramming earth around in layers not exceeding 25cm, watering and removing surplus soil to a distance exceeding 1.5 kilo mtr and making good distrub surfaces as in hard/dense soil complete all as specified and as directed.

Excavation in trenches not exceeding 1.5 m wide & not exceeding 1.5 m in depth for foundations etc and getting out as in hard/dense soil complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25cm thick complete all as specified and as directed.

Removing excavated soil material n.exc 50m and depositing where directed at a level not exc. 1.5m above the base in soil complete all as specified and as directed.

Roof trusses (framed) trussed, purlins, crane gantries rails and fastenings and heavy brackets, post, eves board including frame work and similar work framing (beam, tee, channel or flat sections) including distance pieces cleats including welding etc. complete all as specified and as directed.

PCC (1:4:8) type D-2 as in foundation, filling & mass concrete for in fixing MS bed plates fixed with MS Tubular post complete all as specified and as directed.

PCC (1:2:4) type B-2 (using 40 mm graded crushed stone aggregates) as in foundation, filling in post holes complete all as specified and as directed.

MS flat iron as in wind ties etc confirming to Fe 410-0 or Fe 310-0 including clamps complete all as specified and as directed.

Applying two coats of cement based paint over a coat of chalk whiting including preparation of new plastered surfaces complete all as specified and as directed.

Non skid ceramic tiles, area of each tile exc 0.11sqm but n.exc. 0.18 Sqm, 7mm to 8mm thick (square or rectangular) of superior quality as in floor and walls surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match the coloured tiles complete all as specified and as directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15 cm deep and getting out in hard/dense soil complete all as specified and as directed.

PCC (1:2:4) type B-1 (using 20mm graded crushed stone aggregates) as in coping , benching, bed blocks etc complete all as specified and as directed.

40mm thick (1:2:4) PCC type B-1 (using 20mm graded crushed stone aggregates) as in flooring mixed with WPC as per manufacturers instructions complete all as specified and as directed.

Supply only integral water proofing compound complete all as specified and as directed.

Removing excavated soil material exc. 250m but n.exc 500m and depositing where directed at a level not exc. 1.5m above the base in soil complete all as specified and as directed.

Plain cement concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggregates) as in coping complete all as specified and as directed.

Taking down carefully, copper/ aluminum point wiring (light, fan, socket or power) complete including fitting such as switch, sockets, ceiling rose, pendants socket,fan regulators any type, rectangular board, light fittings,terminal boxes etc removing materials for taking credit and making good disturbed surfaces of walls floors and ceiling complete all as specified and as directed.

Point wiring for one light/ fan/bell point controlled by one switch using 1.5 Sq mm FRLSH copper conductor cables (multistanded) PVC insulated and unseathed in and including PVC concealed conduit as per site requirement (thickness not less than 1.5mm and 20mm dia), medium grade with Modular sunken boxes & PVC back plate for mounting modular type switches, sockets & regulators etc with front plate modular type including supplying and laying PVC insulated unsheathed 1100 volts coppper conductor cable 1.5 Sq mm as earth wire stranded and conected to earth dolly complete all as specified and as directed. Note:- Cutting and making same the wall patchs after laying the wire and conduit using putty, white wash and distamper. The surface should be made smooth using putty and should match exactly with the existing wall finish.

All as per srl item No 170 but for 3 pin 5 Amps socket outlet independent including copper PVC insulated PVC unsheathed 1.5 sq mm earth wire and connected to earth dolly complete all as specified and as directed.

All as per srl item No 170 but for 3 pin 6 Amps socket outlet on the same board including copper PVC insulated PVC unsheathed 1.5 sq mm earth wire and connected to earth dolly complete all as specified and as directed.

All as per Srl item No 170 but for 3 Pin 15 Amps socket outlet independent with cable 2.5 Sq mm including copper PVC insulated PVC unsheathed 1.5 sq mm earth wire standard and connected to earth dolly complete all as specified and as directed.

Modular switch 6 Amps single pole one way 230 volt with outer strip complete all as specified and as directed.

Modular switch 16 Amps single pole one way 230 volts with outer strip complete all as specified and as directed.

Modular Bell push flush type 6 amps with outer strip complete all as specified and as directed.

Modular socket 3 Pin 6 Amps flush type with outer strip complete all as specified and as directed.

Modular socket combined 2-in-1, 6 Pin 6 & 16 Amps flush type with outer strip complete all as specified and as directed.

Ceiling rose, surface bakelite 65mm x 50mm two to three terminals fixed on PVC Round Block complete all as specified and as directed.

Bell AC, 230 volts single pole complete all as specified and as directed.

Supply & fixing in replacement of sheet metal enclosure Single pole & neutral with 2 pin and earth plug and socket 20A 240 Volt complete with one Double pole MCB of 20 A "C" Series of breaking capacity 10 KA complete all as specified and as directed.

S&F in replacement Sheet metal enclosure double door type for MCCB TPN DB Including MCCB 100 Amps, 25 KA, 4 way vertical type 415 volts with 400 Amps rated busbar and neutral link including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and as directed.

S&F in replacement Sheet metal enclosure double door type for DBs (when MCB to be used) 12 way 240 volts with 200 Amps rated busbar and neutral link including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and as directed.

S & F in replacement MCB Single pole and neutral 240 volt any rating from 40 amps 'C' series, with rupturing capacity 10 KA, inculding providing thimble for out going cable complete all as specified and as directed.

S & F in replacement MCB single pole 240 volt any rating from 10 to 40 amps 'C' series, with rupturing capacity 10 KA ,inculding providing thimble for out going cable complete all as specified and as directed.

S & F in replacement MCB single pole 240 volt any rating from 63 Amps 'C' series, with rupturing capacity 10 KA ,inculding providing thimble for out going cable complete all as specified and as directed.

Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 10 Sqmm in PVC concealed conduit 25mm dia including PVC insulated copper conductor cable 6 Sq mm as earth lead all as specified. Including taking down old sub main wire complete all as specified and as directed.

Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 6 Sqmm in PVC concealed conduit 25mm dia including PVC insulated copper conductor cable 6 Sq mm as earth lead all as specified. Including taking down old sub main wire complete all as specified and as directed.

Earthing complete with galvanized steel earth plate electrodes 600mm x 600mm x 6.3 mm thick buried directly in ground earth plate not less than 2.25 m deep below normal ground level with top edge of the plate not less than 1.5 m below normal ground level connected to and including galvanized steel earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron and steel including PCC pit in PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregates), RCC frame with 40mm thick RCC cover reinforced with 8mm dia deformed bars handle. including excavation and earth work in any type of soil medium grade GI watering pipe 20mm bore with funnel and wire mesh and light grade GI protection pipe 15mm bore main board complete all as shown in electrical plate No 5 connected to main control board complete all as specified and as directed and testing on completion. Note: Excavation earthwork charcoal PCC pit is covered under this item including taking out existing earth plate etc.Note: if earth resistance of earthing is not found (2 to 5 Ω) satisfactory if will be redone by the contractor on his risk and cost.

S&F in replacement electronic step type fan regulator 120 watt 230 volts 50 C/S deluxe type complete all as specified and as directed.

Taking down ceiling fan/Exhaust fans (C/F of any size/make), cleaning its dust particles oiling,greasing,one coat of synthetic enamel white spray painting with blade ,reassemble the same along with all fittings and hanging the same back to its original position including connecting the wire to ceiling rose etc complete after completing the wiring complete all as specified and as directed. Note :- (i) The spares like condensor, ball bearing, cotter pin, nuts & bolts, connecting rods & hooks etc if found defective/damage deemed to be replaced and make the ceiling fans functional. No extra payments will be done on this account.

Supply and fixing in replacement LED lights fitting 1x 20W, 230V,AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed.

Supply and fixing in replacement LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable sizecomplete all as specified and as directed.

S & F in replacement LED light fitting 1 x 9W/1 x 10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Supply and fixing in replacement LED luminaire 2 x 2R 36W watt, 230 V AC recess mounted downlighter type with high efficiency PC diffuser soft light and symmentrical illumination complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Decorative wall mounting 1 x 9W chrome finish fixture with frosted glass suitable for 9 W with EL 27 Warm white colour bulb mini GLS lamp luminaire complete all as specified and as directed.

Supply and fixing in replacement LED building security light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp,clamps,suitable bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed.

Supply and fixing exhaust fan, steel body AC single Phase. 230V of size 300m sweep with, blades, and frame and louvers along with all electrical wire connection complete all as specified and as directed.

Material and labour for Fixing & Laying in trenches or passing through pipe, 1100 volts grade heavy duty cable with "XLPE" insulated aluminium conductor standard served with an inner sheathing of PVC tape armoured with galvanised steel wire or tape and overall PVC sheathed of 25 Sqmm x 3.5 core size complete all as specified and as directed including taking down old cable. Note : Earth work and other connected work shall be measured & paid sperately.

Dry sand for sand cushioning to under ground cable 8 cms thick before laying the cable before and 15 cms thick after laying & streching the cable in trenches, including hand punning and consolidating complete all as specified and as directed. Note : for payment purpose punned thickness shall be measured

Bricks sub class 'B' brick laid dry, flat with width equal to length of brick as cover laid over the cabel to give mechanical protection to underground cabels complete all as specified and as directed.

Supply and fixing GI tubing light grade 40 mm dia along the wall/ in trenches/ in duct / in culvert /road crossing and including provisioning of suitable mild steel flat iron clamps and bolts, nuts and double washers etc for holdining of GI pipe alongwith poles complete all as specified and as directed.

Supply and fixing electric water heater,storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate,NRV, connection piece etc complete all as specified and as directed.

Supply and fixing post top lantern LED type 20 watt 230 watt volts AC outdoor type with decorative Crown shaped post top lantern in soothing opal finish made up of Polycarbonate for 360 degree indirect light IP 65 protection with impact and corrosion resistant complete with driver and suitable bulb lamp complete including GI pipe as required complete all as specified and as directed.

Taking down carefully copper/aluminium sub main wiring of size 2.5/4/6 sqmm from surface/concealed at any height and removing the materials from site and making good the disturbed surfaces of walls,floors roofs etc complete all as specified and as directed.

Taking down Old/ Unserviceable MCB DBs TPN / Main Switches by disconnection of electric connection including old unservible MCCBs, MCBs, isolators etc and making good to distrubed surface complete all as specified and as directed.

Disconnecting and taking down un serviceable light fittings of any description/ capacity complete all as specified and as directed.

Supply and fixing Square shape 24 watt 220 volts AC surface mounted type warm white colour with high efficiency soft light and symmentrical illumination complete with drivers, holders,LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Decorative wall mounting 1 x 4W nickle finish fixture with frosted glass along with 4W warm white bulb GLS lamp luminaire complete all as specified and as directed.

Supply and fixing ceiling fan (fancy) AC single Phase. 230V of size 1200mm sweep with, blades, and frame along with all electrical wire connection complete all as specified and as directed.

s l sharma and sons

PARDEEP SHARMA

MAHAJAN TRADING CO