Site paneling and other works at Community Hall Kungyam

Amount

20 mm cement plaster of mix 1:4 (1 cement :4 fine sand)

Dismantling roofing including ridges, hips valleys and gutters etc., and stacking the material within 50 metres lead of G.S. Sheet

.Providing corrugated G. S. sheet roofing including vertical/ curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G. I limpet washers or with G. I. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/vertical or curved surface)excluding the cost of purlins, rafters and trusses and including cutting to size and shape whereever required 0.63mm thick with zinc coating not less than 27 5gm/m2

Dismantaling of old plaster or skirting , raking out joint and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metre lead

15mm Cement plaster on the rough side of single or half brick wall of mix: 1 : 4 ( 1 cement : 4 coarse sand)

Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacture, over the plastered wall surface to prepare the surface even and smooth complete.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade New work (two or more coats) over and in -eluding priming coat with cement primer

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade. Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture

providing and fixing 12 mm thick plywood and T&G wall panelling with polishing and complete job

Random Rubble masonry with hard stone from nallah in foundation and plinth including levelling up with cement concrete 1 :6:12 ( 1 Cement: 6 coarse sand : 12 graded stone aggregate 20mm nominal size) at plinth level withcement mortar 1:6 (1 Cement: 6 coarse sand)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z. sections and other sections of approved make conforming to IS : 733 and IS : 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber I neoprene .. gasket felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing I panelling, C.P. brass I stainless steel screws, all complete as per architectural drawings and the directions of Engineer-inCharge (glazing, panelling and dash fasteners to be paid for separately.)Anodised aluminium (anodised transparent or -~ dyed to required shade according to IS: 1868, minimum anodic coating of grade AC 15)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z. sections and other sections of approved make conforming to IS : 733 and IS : 1285, fixed with dash fastener of required dia. and size including necessary filling up of gaps at junctions i.e, at top, bottom and sides with required EPDM rubber I neoprene .. gasket felt etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing I panelling, C.P. brass I stainless steel screws, all complete as per architectural drawings and the directions of Engineer-inCharge (glazing, panelling and dash fasteners to be paid for separately.)Anodised aluminium (anodised transparent or <lyed to required shade according to IS: 1868, minimum anodic coating of grade AC 15)

Providing and fixing 12mm thick prelaminated particle boardflat pressed three layer or graded wood particle board (conforming to IS: 12823 Grade-l type-11) in panelling fixed in aluminium doors, windows shutters and partition frames with C. P. brass I stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge.Pre-laminated particle board with decorative lamination on both sides

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber I neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (Cost of aluminium snap beading shall be paid in basic item.)With float glass panes of 8 mm thickness (weight not less than 20.0 kg I sqm)

Providing and fixing aluminium round shape handle of outer dia 1 OOmm with SS screws etc. Complete as per direction of Engineer-in-charge Powder coated minimum thickness micron aluminium

providing and fixing brass tower bilts (barrel type) 100x10 mm DOOR

providing and fixing brass tower bilts (barrel type) 100x10 mm WINDOW

Providing corrugated G. S. sheet roofing including vertical/ curved surface fixed with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G. I limpet washers or with G. I. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (upto any pitch in horizontal/vertical or curved surface)excluding the cost of purlins, rafters and trusses and including cutting to size and shape whereever required. 0.63mm thick with zinc coating not less than 27 5gm/m2

Renewing glass panes, with wooden fillets wherever necessary :Glass panes weighing 10 kg I sqm

using manual labour for laying of 40mm thick factory made cement concrete interlocked over blocking machine with strong vibrator composition and of approved colour and pattern over and including 50mm thick compacted bed of warse sand , filling the joint with coarse sand etc all complete as per as direction of engineer incharge , including , loading , unloading and carriage complete job

cost for Tiles

carriage of cement from average km lead upto 100 km

carriage of sand and aggregate from average km lead upto 40 km

carriage of stone from average km lead upto 5 km

M/S TSERING DORJEY GOVT CONTRACTOR