REPAIR MAINT TO JOINERY, SEEPAGE, FLOORING, PLUMBING, SANITARY FITTINGS, PLATERING, BRICK WORK, PLINTH PROTECTION, CHAJJAS , ROOF AND OTHER ALLIED WORK IN OFFRS ACCN AND EM INSTALATION UNDER AGE BR-I OF GE (WEST) PATHANKOT

Amount

Taking down chowkhats or frames with shutters exc 1.50 Sqm and n.exc 4 Sqm each (without talking off shutters from the frame) complete all as specified and directed.

Taking down chowkhats or frames with shutters n.exc 1.50 Sqm each (without talking off shutters from the frame) complete all as specified and directed.

Taking down shutters of any description exc 1 Sqm but not exc 2 Sqm each complete all as specified and directed.

S&F pressed steel frame made out of 1.25mm thick MS Sheets of section of size 105mm x 60mm for doors with one or more rebates incl necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed

S&F pressed steel frame made out of 1.25mm thick MS Sheets of section of size 125 mm x 60mm for doors with one or more rebates incl necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed.

S&F pressed steel frame made out of 1.25mm thick MS Sheets of section of size 165 mm x 60mm for doors with one or more rebates incl necessary fixing lugs, hinges, lock strike plate, etc complete all as specified and directed.

M&L for cement concrete type B-1, 1:2:4 (using 20mm graded crushed stone aggregate) as in bed plates for securing hold fasts & back filling of hollow portion of chowkats etc complete all as specified and directed.

Factory made Solid PVC Door Frame of size 50mm x47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening as per specification & drawing complete all as specified .

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Paneling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing complete all as specified .

All as per srl item No. 9.00 here-in-before but wire gauzed ie.panel will be of wire gauze in lieu of PVC sheet panel. The wire gauze shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be welded to M.S. tubes. The wire gauge shall be stretched to tighten firmly.The rate included for stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm.

S&F Factory made 35mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F factory made 35mm thick of 2nd class hard wood Glazed and skeleton door shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain ,chamfered or rounded. fitted with cut and mitered beads for securing glass ,etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats, kiln seasoned, chemically pressure treated complete all as specified.

S&F Factory made 35mm thick Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated,2nd class HW rail and style complete all as specified and directed.

S&F Factory Made 30mm thick High density fibre panel board (HDF) door shutter as per details shown in drawings No. CEPZ/C-TD-037/13 sheet 1/2 & 2/2 respectively & conformed to IS: 15380-2003 complete all as specified and directed.

S&F in repair Steel window/ventilator factory made, made out of mild steel box type and shutter suitable for double shutter i.e. Glazed and gauged shutter. Glazed shutter made out of hollow' section with sash bar and gauged shutter made out of hollow section without sash bar including hinges, tower bolt, handle, grill 10 mm sq bar including two coat of synthetic enamel paint over one coat of red oxide primer, tarred hold fasts, PCC bed blocks for fixing hold fast, including plain/figured glass and stainless steel wire cloth 0.36mm nominal dia of wire & average width of aperture 1.18mm & fixed with stainless steel wire staples`etc complete all as per details shown in drawing No CEPZ/C-TD/032/13 sheet No 1/2 & 2/2 including taking down existing spoiled and unserviceable windows/ventilators of any type ( wooden/steel) complete all as specified and directed

Taking down for re-fixing aluminium doors,window shutter area not exc 3.0 Sqm each and cutting it to required shape including replacement of joining cleats,glazing clips, ruber neoprene packing,handles 2 Nos in each door,hinges,anodised aluminum snap beading,screws,sash bar & peg stays etc and fixing in same opening & making smooth functioning for proper closing ,opening complete all as specified and directed.

S&F in repair anodised aluminum frame for partition, doors, windows, ventilators, sliding shutters etc with one or more rebates including joining cleat for fixing etc including taking down old frames with shutters complete all as specified and directed.

All as per item no 17.00 here-in-before but powder coating of any colour (minimum thickness of powder coating 50 micron)

S&F in repair Anodised aluminum window and ventilator shutters, fixed type without sash bar, fixed/sliding/rolling type, aluminum section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminum snap beading, screws etc. complete all as specified and directed.

All as per item no 19 here-in-before but powder coating of any colour (minimum thickness of powder coating 50 micron)

S&F in repair for Anodised aluminum window and ventilator shutters, side hung type without sash bars, aluminum sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminum fittings such as peg stays 150mm long (1 no.). hinges type B-21100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed.

All as per item no 21.00 here-in-before but powder coating of any colour (minimum thickness of powder coating 50 micron)

S&F in repair Anodised aluminium door shutters,aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing,handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and directed.

S&F sheet glass 4.8 mm thick, ordinary quality and glazing in Aluminium shutter in square n exc 0.5 sq. m in each pane complete all as specified and directed

S&F sheet glass 4.8 mm thick, ordinary quality and glazing in Aluminium shutter in square exc 0.5 sq. m in each pane complete all as specified and directed

S&F 4mm thick aluminum composite panel (coloured sheet) and in additional other accessories for fitting in aluminum partition / doors / windows / ventilators /sliding shutters etc complete all as specified and directed.

S&F anodised designer grill (weight of grill shall not less than 2.00 KG/Sqm) of 07mm dia and aperture of 75mmx75mm fixed with and including aluminum flat section of size 50 x 1.5 mm fixed to aluminium windows Complete all as specified and as directed.

S&F in repair 10mm thick Toughned glass as in hinged doors partitions automatic doors and similar work including cutting to shape drilling holes required etc complete all as specified and directed.

S&F in repairs for Door closer hydraulically regulated, designation No. 3,universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed aluminium (Diecast) body complete all as specified and directed.

S&F in repair of double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box,main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified and directed

S&F butt hinges medium weight 100 mm cold rolled mild steel complete all as specified and directed.

S&F in repair butt hinges medium weight 100 mm cold rolled mild steel complete all as specified and directed.

S&F 250mm long Aluminum alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminum alloy complete all as specified and directed

S&F in repair 300mm, mild steel ordinary rat tail rod pattern springs including roller and roller plate complete including welding to steel frames as required at site complete all as specified and directed.

S&F 200mm long aluminum, anodised, barrel tower bolts of extruded section and fixed, complete all as specified and directed.

S&F 150mm long Extruded aluminum alloy handles, fabricated type, anodised complete all as specified and directed.

S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or using metal nut and bolts complete all as specified and directed.

S&F in repair stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or using metal nut and bolts complete all as specified and directed.

S&F in repairs galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

S&F in repair Door seal powder coated aluminum brush type polypropylene screwed down to shutters complete all as specified and directed.

S&F in repair for curtain rails 25 mm dia of pre painted aluminium with fixing brackets, stops, rollers, knob etc complete all as specified and directed.

S&F in repair heavy duty stainless steel bright finished, fancy type decorative brackets fixed with PVC plug/gutty & screws etc complete all as specified and directed.

M&L for 18/19mm thick Pre-laminated particle board, exterior grade, pre-laminated one side with decorative choice lamination & other side balancing white lamination with 6mm thick teak wood lipping fixed with screws to steel/timber frame work as in shutters & shelf of Kitchen cabinet, cupboard, partition & almirahs etc including taking down old shutters & shelf etc complete all as specified

M&L for 18mm thick ultra voilet printed PVC board (weight not less than 12 Kg/Sqm) duly edge bonded with 0.8mm thick PVC taping as in shutters & shelf of Kitchen cabinet, cupboard, partition & almirahs etc fixed with screws to steel/timber frame work etc including taking down old shutters & shelf etc including taking down old shutters & shelf etc complete all as specified

M&L for decorative laminates 0.9mm thick type-I, or surface finish, colour and pattern as approved fixed with approved adhesive as per manufacturer's instructions complete all as specified and directed.

S&F in repairs for 18mm thick Medium density fibre board both side Prelaminated with decorative choice, exterior grade, fixed to timber framework with screws as in shutters & shelfs of Kitchen cabinet, cupboard, partition & almirahs etc including taking down existing shutters ,shelfs / boards /cabinets etc complete all as specified and directed

S&F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised with width of flaps (When open) 30 mm complete all as specified .

S&F 100mm long Hasp & staple, safety type, aluminum anodised with hinge pin including bolt to hinge plate with screws complete all as specified.

S&F Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in etc complete all as specified

Taking up or down 15mm bore, steel water tubing and connection including cleaning for refixing or removal from site complete all as specified .

All as per srl item No 51.00 here-in-before but 20mm bore Steel water tubing

S&F 15 mm bore Steel water tubing 'medium grade', galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified .

S&F 20 mm bore Steel water tubing 'medium grade', galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified .

Re-fixing 15mm bore old steel water tubing with all new GI fittings etc in new or old position (Walls, ceiling, floors, etc) complete all as specified

Re-fixing 20 mm bore old steel water tubing with all new GI fittings etc in new or old position (Walls, ceiling, floors, etc) complete all as specified

Cutting chases in brick walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, shelves, lintels, etc, and cutting chases for concealed water tubing or conduit wiring, etc and making good, cutting not exceeding 10cm girth complete all as specified

Dismantling of Asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings or PVC sheet in roof including ridges, sunshades or any position etc complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including nainital or similar pattern roof covering from sunshades etc complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in sunshades ,roof covering, cladding to wall etc fixed with self tapping screws complete all as specified and directed.

S&F pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering / cladding to wall and as in ridge etc fixed with self-tapping screws complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for including grills, door, truss, gate, rafters, purlins etc complete all as specified and directed.

Dismantling timber scantlings 40sqcm and over in section, in any position as in wooden trusses in framed work of any description complete all as specified and directed.

S&F Rolled structural mild steel any type hollow section as in main and cross beams, hip and jack rafters; purlins where connected to a common rafters and rails and guides for sliding doors; and supports to roof covering, sun-shades,vertical poles etc fixed with angle cleats or other connecting plates Fe-410-W(Gde-E-250) quality B complete all as specified .

S&F Framed work such as grills,gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; railings; framework of water tanks ,framed and hung as in steel gates including pintle hinges, stops,hand-made sliding bolts etc and similar work conforming to Fe.290.Gde-E-165,ornamental and intricate design complete all as spd and directed.

S&F of mild steel, plain, black sheet 1.25mm thick in wall cladding, steel gates and similar work, cut to size, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel framing with plain 40 mm lap joints with riveted or welded seams, including bending or turning up, mitred angles, etc. as required complete all as specified and directed

Demolition of brick work or stone/ boulder masonry built in cement mortar or cement lime mortar including all quions, wall, arches, pillars, man-holes, drain etc complete all as specified and directed.

M&L for fly ash brick work (class designation 75 kgf/Sqcm) , straight or curved on plan exc 6 m mean radius built in cement mortar 1:4 complete all as specified and directed.

Taking down cement plaster of any description and thickness on walls/ceilings etc including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 including mixing of liquid water proofing compound @2% by weight of cement or as per manufacturer instruction, on fair faces of brick work ,concrete surface of wall, fin, facia, chajjas, parapet and similar article finished surface even and smooth without using extra cement complete all as specified. Note:-No price adjustment to be made if WPC used more than 2%.

All as per srl item No 70.00 here-in-before but on other than fair faces

M&L for 10 mm thick rendering on brick work or concrete surfaces in CM 1:3 as in ceiling of roof slab ,fin, facia, culvert, chajjas, parapet and similar article etc finishing surfaces even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of Cement Base Paint over and including one coat of alkali resistant priming paint complete all as specified

M&L for preparing of new plasterd wall surfaces and applying of two coat of oil bound distemper over and including a coat of primer using chalk whiting etc complete all as specified and as directed.

M&L for preparation of old plastered or unplastered ,old/un decorated surfaces of brick/concrete/stone wall surface by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc and applying two coats of white wash complete all as specified and as directed. Note: All painted areas site to be cleaned and hand over as earlier without any extra cost to Govt

All as per ser item no 76.00 here-in-before but applying two coats of white wash on ceiling surface

M&L for preparation of old plastered or unplastered ,old/un decorated surfaces of brick/concrete/stone wall surface by brooming down or steel wire brushing, scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots etc and applying two coats of cement Base Paint over and including one coat of alkali resistant primer complete all as specified and as directed. Note: All painted areas site to be cleaned and hand over as earlier without any extra cost to Govt

Demolition of existing roof treatment of any description such as worm out tarfelt, mortar of any description & any thickness, shrubs/roots ,vegetation, tree, terracing pcc/brick tiles, concrete bedding etc as directed and Cleaning of all foreign material debris etc by brushing and dusting, washing down with water etc and surface shall be leveled with a layer of 20 mm thick screed bed in CM 1:4 including mixed with water proofing admixture as per manufacturer's instructions and applying roof treatment with 03mm thick APP modified membrane with non-woven polyster reinforcement(center core) with thermal insulation with white mineral gravel finish on upper side of weight not less than 3.5 kg/sqm , laid by torch application method with overlap 100 mm on length side and 100 mm on the width side as per manufacturer's instructions over one coat of approved cold applied bituminous oil based primer (IS-3384) @0.30 litre/sqm complete all as specified and directed

Demolition of RCC of any description slab , shelves , cover slabs for drain & manholes,chajjas, water tank ,chullah hoods etc and in any position including cutting reinforced as required complete all as specified .

M&L for RCC type B-1 (1:2:4) using 20 mm graded crushed stone aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200mm thick horizontal or sloping for rough finished surfaces of concrete complete all as specified and directed.

M&L for Mild steel TMT bars 10mm dia & over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends & binding with & including mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality complete all as specified and directed.

M&L for preparation of newly steel and iron surface of any description width or girth exc 10 cm and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L for preparation of old painted steel surfaces of any description over 10 centimeter width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

Taking down eaves gutter and rain water pipe any size any pattern ,PVC/ AC pipe including all fittings ,Internal dia of pipe in 75/110mm complete all as specified and directed.

S&F PVC (SWR) pipes 75mm bore single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F PVC (SWR) pipes 110mm bore single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F in repairs for PVC (SWR) bends ISI marked of radius 75mm dia complete all as spd and directed.

S&F in repairs for PVC (SWR) bends ISI marked of radius 110mm dia complete all as spd and directed.

S&F Rotational moulded polyethylene water storage tanks of 500 ltrs capacity ISI marked (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including Ball valves high pressure of PTMT with epoxy coated aluminum rod & high-density plastic bal screwed for iron pipe and fixed. (Minimum weight 20mm-210 gms including dismantling of old Brocken water tanks and refixing of inlet, outlet & over flow pipe etc complete all as specified and as directed.

All as per Srl item No. 91.00 here-in-before but size 1000 Ltr capacity

S&F in repair Ball valves 20mm bore high pressure of PTMT with epoxy coated aluminum rod & high-density plastic bal screwed for iron pipe & fixed (min. weight 20mm-210 gms) complete all as specified and directed.

S&F in repair for gun-metal, globe or gate valves 20mm bore, with iron wheel head, screwed both end for iron pipe complete all as specified and as directed.

Hacking out old broken glass (any the size quality or description) from wooden or steel frames glazed complete all as specified and directed

S&F 3 mm thick sheet glass, ordinary quality and glazing with oil putty and glazing clips in metal frame and second class hard wood beading in suitable size for wooden frames in squares not exc 0.5 Sqm in each pane complete all as specified and directed.

S&F 3.0 mm thick figured Sheet glass, pin head type or-dinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane ,complete all as specified and directed

M&L for preparation of newly wooden Surfaces of any description, not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

Supply only liquid water proofing compound all as specified and as directed.

M&L for repairing to chajjas, roof projection and facias of exposed reinforcement surface or damaged loose RCC surface including cutting down rusted/exposed reinforcement and applying one coat of cement slurry and filling with cement concrete 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregate) and finished with cement mortar 1:3 using coarse sand with mixing of liquid water proofing compound @2% by weight of cement or as per manufacturer instruction. Thickness of RCC member not exc 150 mm including scaffolding up to 8.0m height complete all as specified and as directed . Note : (i) No extra rates of scafffolding will be paid separately against this item. (ii) Water proofing compound will me measured and paid sepratly.

Dismantling of Stone slabs & tiles of any description or thickness in floors, aprons etc. Laid, bedded & pointed in any mortar complete all as specified and directed.

M&L for 80mm thick M-40 Grade, rubber moulded glossy finish Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 with grey cement and pigment including 25mm thick sand cushioning bed complete all as secified and directed.

M&L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade with grey Cement and no pigment including 25mm thick sand cushioning bed complete all as secified and directed.

M&L for Chequered cement concrete tiles 30cm x 30cm x 25 mm /20cm x 20cm x 25 mm thick , set, jointed and pointed in neat cement slurry as in floor/path etc with grey cement and pigments and including 20 mm thick cement screed in cement mortar 1:6 including demolitio/dismantling old pcc/tiles complete all as specified complete all as specified and as directed.

M&L for Non abrasive paving (rectified endura) cement concrete coloured tiles 300 mm x 300 mm x 10 mm thick set jointed and pointed in neat cement slurry mixed with pigment laid over 15 mm thick screed bed in cement mortar 1:4 including dismantling complete all as specified and directed.

Demolition of cement concrete or lime concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L for 75mm thick plain Cement concrete 1:3:6, type C-1 (using 20mm graded crushed stone aggregate) as in plinth protection,and paving 75 mm thicklaid in sloe finished even and fair including making joints at every 2.5 m and at corner filled with bitumen 85/25 and sand in ration 1:2 by weight and complete all as specified.

M&L for 40 mm thick plain cement concrete type B-1 , 1:2:4 (using 20 mm graded crushed stone aggregate) finished even and smooth without using extra cement as in flooring complete all as specified and directed. Note- Glass dividing strips shall be measured & paid separately as supply only.

M&L for 100 mm thick plain cement concrete type B-1 , 1:2:4 (using 20 mm graded crushed stone aggregate) finished even and smooth without using extra cement as in flooring complete all as specified and directed.

supply only 38 mm wide and 3 mm thick glass dividing strips in flooring by fixing in position and making square or rectagle for casting concrete in flooring complete all as specified and directed.

S&F in repair Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe), trap, including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, etc. complete, including Plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminized hinging device complete all as specified and directed.

S&F in repair for vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) squatting pan including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor complete all as specified and directed.

S&F in repair for for Vitreous China wash basin, white or in matching colour of tiles, flat back, size 630x450mm including brackets, CP brass waste fitting 32 mm dia,PVC waste pipe 750 mm long( Minimum) cutting for and pinning in ends of brackets or erecting stand complete all as specified.

S&F in repair for 10 ltrs capacity PVC valve less, syphonic action type, flushing cistern, low level, white, with intel, ball valve, float and handle including brackets ,fush pipe of polyethylene of low or high density or PVC 32 mm dia complete all as specified.

S&F in repair for 15mm dia PVC connections 600mm long with PTMT nuts complete all as specified.

S&F in repair PVC bathroom cabinet mirror of size 450mmX350mm wall mounted, shape rectengular fixed to wooden plugs with CP brass screws and cup washers complete all as specified and as directed.

S&F in repair Brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and as directed.

S&F in repair stainless steel towel rack 600mm long with lower hangers complete all as specified and as directed.

S&F in repair CP brass towel ring 20mm dia, fancy type, superior quality, including CP screws and wooden/plastic cleats complete all as specified and as directed.

S&F in repair 15mm bore dia fancy type, chromium plated angle/stop valves, cast copper alloy, screwed down, high pressure ,with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed (minimum weight 575 grams) complete all as specified and as directed.

S&F in repair for 15 mm bore chromium plated fancy type Bib taps, cast copper alloy with crutch or above butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and as directed.

S&F in repair for brass chromium plated long body bib cock with wall Flange complete all as specified and directed. Make-Jaquar cat no CON-CHR-107KN or equivalent in any of the make mentioned in list of product.

S&F in repair 15mm bore dia fancy type, chromium plated long shank and cup (concealed type) stop valves, cast copper alloy, screwed down, high pressure ,with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and as directed.

S&F in repair for fancy type Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed (minimum weight 665 grams) complete all as specified and directed.

S&F in repair 15mm bore, brass CP mixer for mixing Hot & cold water screwed down for iron pipe and fixed for basin, sink or bathroom complete all as specified and as directed.

S&F in repair CP over head Shower 190mm dia round shape single flow (ABS Body Chrome Plated with Gray Face Plate) with rubit cleaning system with 190mm Long Flat Shape shower arm chrome plated Casted with Flange complete all as specified and as directed.

S&F in repair Hand Shower (Health Faucet) with 8 mm dia,1.2 m long Flexible Tube Chrome Finish & Wall Hook for Water closet complete all as specified and directed. Make Jaquar CAT NO Health Faucet SKU ALD-573 or equivalent in any of the make metnioned in list of product.

S & F in repair Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed.

S & F in repair corner glass shelf with bracket fixed with chromium plated brass screws and wooden/plastic cleats complete all as specified and as directed. Make : ACN-1173 of JAQUAR or equivalent in any of the make mentioned in list of products.

S&F in repair chrome finish Toilet paper Roll Holder with fixing arrangement complete all as specified and as directed.

S&F in repair Stainless Steel Soap Dish or Soap Holder Dish for Bathroom with fixing arrangement complete all as specified and as directed.

S&F in repair for 75mm PVC floor trap, ISI marked with perforated grating incl jointing to waste pipe fixed with solvent cement complete all as specified.

S & F in repair sink with drainage board made of stainless steel 1 mm thick with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets of angle iron and connecting union to pipe over all size 915 mm x460 mm and bowl size 410mmx330mmx 160mm complete all as specified and as directed.

M&L in repair Stainless steel plate rack(Utensil Rack) of size (900mm x 750mmx250mm ) made out of AISl 304 stainless steel 0.63 mm thick sheet fixed with screw of required size including necessary fittings/nuts, bolts & washers complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and as directed.

M&L for joint free Non - skid Ceramic Coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 15mm thick screed bed in CM 1:4 complete all as specified and as directed.

All as per srl item No 137.00 here-in-before but as in vertical/skirting surface etc over and including 10mm thick rough cement plaster to receive tiles in CM 1:4

M&L for Joint free Glazed ceramic Coloured tiles in vertical/dado surface 450mmx300mmx7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over & including 10mm thick rough cement plaster to receive tiles in CM 1:4 complete all as specified and as directed.

M&L for Vitrified Ceramic tiles 10 mm thick light shade (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm in floors etc (size of each tile 0.6m x 0.6m), set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 15mm thick screed bed in CM 1:4 complete all as specified

All as per srl item No 140.00 here-in-before but as in vertical/skirting surface etc over and including 10mm thick rough cement plaster to receive tiles in CM 1:4

M&L for 18-20mm thick granite (pure black) work (table rubbed and polished) in steps, jambs pillars, window cills ,cooking platform and like including pointing in white cement (1:2) using marble dust with admixture of pigments to match with shade or granite over including 15mm thick screed bed or bedding layer in cement mortar 1:4 complete all as specified and as directed.

M&L for providing 35mm thick precast cement concrete louvers and jallies (measured solid) in 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate set in cement mortar 1:4 including all mouldings complete all as specified and directed.

M&L for Precast cement concrete type B1 (1:2:4) using 20 mm graded aggregate in lintels, copings, kneelers, apex stones, pier caps, columns, posts, boundary pillars, balusters with plain fair faces, including chamfers, weatherings, throating etc. and setting in CM(1:4) with joints to match complete all as specified and directed.

M&L for machine cut kota stone slab flooring 18-20mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete over screed bed or bedding layer 20 mm thick in cement mortar 1:4, complete all as specified and directed. Note:- Rate included for all cutting ,waste including machine cutting to make it square or rectangular,cutting and polishing by machine & size of kota stone shall not be less than 550 mmx550mm .

M&L for machine cut kota stone slab 18-20mm thick in riser of steps, skirting, dado and pillar laid over backing coat 10mm thick in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and directed. Note:- Rate included for all cutting ,waste including machine cutting to make it square or rectangular,cutting and polishing by machine & size of kota stone shall not be less than 550 mmx550mm .

M&L for cutting down plants / trees of girth not exc 15 cm & surface area not exc 36 cm each from roof tops /sides of external walls of buildings, chajja, wall junctions, junctions of of rain water / soil /waste vent pipes including taking out roots entered in wall/slab surfaces and making good the surfaces including repairing the CI/GI/PVC joints of affected locations by applying TUFALO (herbal medicine )and making good to suit the adjoining surfaces using PCC type 1:2:4, type B-0 (using 12.5mm graded crushed stone aggregate) or cement mortar 1:2 complete all as per manufacturer instructions and as specified.

Grinding with machine grinder of granite stone,terrazzo topping with marble aggregate,marble Stone slab, kota slab etc. as in old floor, wall, cooking platform, shelf etc & polishing complete all as specified and directed.

S&F of 2 lever brass mortice lock, vertical type, size 100 mm complete all as specified and directed.

S&F in repairs of 2 lever brass mortice lock, vertical type, size 100 mm complete all as specified and directed.

S&F second class hard wood plain fillets, square, rectangular or triangular in section, and secured with nails or screws, clean sawn and sectional area exc 13 Sqcm and not exc 25 Sqcm including taking down old fillets complete all as specified and directed.

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets complete all as specified and as directed.

S&F for suspended false ceiling system using chicago metallic (E grid) exposed supended system, grid section size 600mm X 600mm comprising of GI powder coated Main Runner of dimensions 39 mm X 24mm X 0.8mm (thickness comprising of GI/0.4+ PPPCGS/0.3mm & weight of runner 1.35 kg for 3600 mm length) Cross Tee of dimensions 29mm X24mmX 0.8mm thick and wall angle 22.2mmX22.2mmX0.65 mm thick ( thickness comprising of GI/0.35+ PPPCGS/0.3mm & weight of angle 0.70 kg for 3050mm length)with and including 4mm thick HPSC(High pressure steam cured) pre-primed, self embossed. textured designer board, water resistant termite resistant, fire resistant for insulation to be placed in the grid system duly suspended with 4mm dia GI bar hangers fixed purlins of the roof with butterfly clips(Wt-0.007 Kg/clip)hold down clips (Wt-0.0035 Kg/clip) complete all as specified and directed.

Notes :- (a) The contract sum shall be arrived at after deduction of amount of Schedule of Credit. (Rs. 94,921.00). (b) PERFORMANCE SECURITY :- (Refer condition 19 of IAFW-2249) The performance security for an amount equivalent to 5% (Five percent) of the accepted contract sum shall be delivered by the successful bidder immediately after the date of intimation letter of acceptance and all provisions shall be applicable as per condition 19 of IAFW 2249

kay gee construction co

M/S Raghuvanshi Builders

DABGOTRA BUILDERS