Spl repair to bldg No P-315 of Jadhunath Enclave at Tibri Mil Stn Gurdaspur.

Amount

Dismantling of roof brick tiles fixed in cement mortar in single layer all as specified.

Demolition mud phuska in roofs any thickness including plastering and leeping all as specified.

Roughing the surface of old concrete floor picking sweeping cleaning and washing down with water to remove dust/mud etc.and brushing with neat cement slurry @ 3kg/Sqm all as specified.

M&L for PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified.

M&L for cement concrete 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) as in roof padding averaging thickness of 50 mm complete all as specified.

M&L for applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq m including cleaning surface as specified and directed (roof treatment and sunken portion area)

M&L for APP based polymeric membrane minimum weighing 3 kg/ Sqm and minimum 3mm thick, reinforced with polyster non wove fabric (weight not less than 150 gms/ Sqm) including bitumen primer @ 0.40 kg /Sqm by forced application with butane torch over entire roof area with minimum overlaps of 100mm at the sides/ longitudinal edges of strips membrane and 150mm at the ends and sealed complete all as specified and directed and all as per manufacturer's instructions.

M&L for 40mm thick brick tiles laid over 15mm thick bedding layer of ready mix mortar bedding, grouting and pointing in CM (1:3) with crude oil 5% by wt of cement all as specified and directed.

All as per Srl item No 08 above but except tiles (old serviceable dismantled tiles obtained from Srl item No 01 shall be reused after necessary cleaning of mortar) all as specified.

Demolition of cement concrete above ground floor and in any position all as specified.

M&L for water proofing treatment to sunken floors of toilets, laboratories, bath, WCs, kitchen etc as under:- (i) Application of two component acrylic modified cementitious coating :- (a) The surfaces to be applied shall be completely dry and free from containments such as dirt, dust, oil, surface treatments and old coatings. Concrete substrates must be mechanically prepared using abrasive blast cleaning or milling to remove cement laitance existing coating and achieve a gripping profile that is clean, dry and free from laitance and any other from of surface containmation. The installation instruction in manufacturer's published literature shall be strictly complied with, including but not limited to the following:- (b) Chipping out any visible cracks in "V-Groove" pattern as applicable. Cleaning of cracks & filling with SIKA latex SBR 100 putty/Dr. Fixit 302 SBR latex/ perma latex SBR/FOSROC Nitbond SBR latex/Asian paint latex as required. Final cleaning of surface with powder grinder, wire brush, hair brush & vacum pressure. (c) Providing and applying a protection concrete 1:2:4, 50mm thick admixed with plastocrete over the applied water proofing coating on horizontal surfaces.(Admixture: Sikaplastocrete plus/FOSROC/Dr. Fixit/STP/CICO confirming to IS 2645.) (d) Dampen all surface immediately ahead of apllication of acrylic modified cementitious coating of SIKA top seal-107/Brush bomd FOSROC/Dr. Fixit/STP/CICO. (e) Whilst the surface is still damp from saturation (SSD) apply one coat of acrylic modified cementitious coating of SIKA top seal-107/ Brush bond FOSROC/Dr. Fixit/STP/ white first coat is wet.

(f) Apply glass fabric sheet of approved make while the first coat is wet. (g) Once touch dry, apply second coat of acrylic modified cementitious coating of viscosity as per manufacturer ins on the entire area. Second coat shall be applied after 6-8 Hrs of application of previous coat and in the direction right angle to the previous coat. (h) The waterproofing coating shall be taken to a height minimum 300mm above the finished floor level on the vertical surface. (j) It is essential to cure acrylic moified cementitious coating immediately after application (min 6-8 hrs drying) for a min of 3 to 5 days to ensure full cement hydration and to minimize cracking. (k) A protection plaster (15mm thick) in ready mix mortar to be a apllied on the walls. (l) All the corners and joints shall be pretreated with an elastic waterproofing sealing tape with a woven bonding mesh on each surface and an elastic expansion zone in the centre of make seal tape SIKA/FOSROC/Dr. Fixit/STP. (m) The membrane has to be protected in accordance with the manufacturer's recommendation until placement of concrete. The membrane to be inspected for damage just prior to concrete placement and carryout repairs in accordance with manufacturer's recommendations. (n) Waterproofing treatment shall be carried out through authorised applicators authorised.

(ii) All the joints of pipes and traps within the sunken portion shall be sealed properly by epoxy sealant. (iii) All CI/PVC Traps in sunken slabs to be enclosed with PCC 1:1.5:3 (using 40mm graded crushed stone aggregate) (min 15cm) all round. (iv) The sunken portion shall be filled with PCC 1:5:10 type E-2 (using 40 mm graded crushed stone aggregate) complete all as specified. (v) Providing drainage spout pipe GI 40mm dia bore light grade upto outside of outer wall (Approx 300 mm to 450 mmlong) incl cutting to existing wall and making good the distrubed surface complete all as specified and directed. (vi) Providing 25mm thick cement concrete 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregate) as in flooring for laying floor finishes all as specified. (Note:- Items no. (iv), (v) and (vi) shall be measured and paid seperately).

M&L for PCC (1:5:10) type E2 (using 40mm graded crushed stone aggregate) filling fdn and mass concrete in sunken floor complete all as specified and directed.

M&L for 25 mm thick PCC (1:2:4) type B-0 (using 12.5mm graded crushed stone aggregate) as in sub base for complete all as specified.

M&L for rendering 12mm thick with ready mix mortar of any size of approved makes on brick or concrete surfaces of walls, finished surface even and fair upto ht 12mtr including taking down cement plaster of any description, complete all as specified and directed.

M&L for rendering 15mm thick with ready mix mortar of any size of approved makes on brick or concrete surfaces of walls, finished surface even and fair upto ht 12mtr including taking down cement plaster of any description, complete all as specified and directed.

M&L for rendering 5mm thick with ready mix mortar of any size of approved makes on brick or concrete surfaces of walls, finished surface even and fair upto ht 12mtr including taking down cement plaster of any description, complete all as specified and directed

M&L for preparation of new plastered surface of walls/ concrete surface and applying two coats of 100% premium acrylic exterior emulsion paint having VOC less than 50gm/ litre and UV resistance as per IS 15489-2004, alkali and fungal resistance , dirt resistance exterior weather paint of required shade (company depot tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior pri mer applied @ 0.90 litre/ 10 sqm over new surfaces all as specified and directed.

M&L for preparation of newly plaster surface and applying two coats of interior acrylic emulsion paint of wall over a coat of 1mm thick wall putty on wall complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of newly plastered surfaces and applying two coats of white wash on walls complete all as specified and directed.

M&L for preparation of newly plastered surface of ceiling and applying three coats of white wash complete all as specified & directed.

M&L for preparation of old surface shall include brooming down or steel wire brushing; scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots on existing surfaces and applying two coats of oil bound distemper on walls complete all as specified and directed.

M&L for preparation of old plastered surfaces of ceiling by brooming down, making good holes, cracks etc and applying two coats of white wash including cleaning the floor/ joinery surfaces, galss panes all as specified and directed by Engineer-in-Charge.

M&L for complete removal of existing treatment and preparation of old plastered surface of internal wals rubbing down, making good holes, cracks etc and stopping etc on existing distempered surfaces and applying two coats of interior acrylic emulsion paint over a coat of 1mm thick wall putty on wall complete all as specified and directed.

Taking down chowkats with shutter n.exc 1.50 Sqm each (without taking off shutter from the chowkats) all as specified and directed.

All as per Srl item No 24 above but exc 1.50 sqm but n.exc 4 Sqm.

Taking down shutter of any description exc 1.00 Sqm but n.exc 2.00 Sqm each complete all as specified and directed.

S&F pressed steel frame for doors with one or more rebate including necessary fixing lugs, hinges, lock strike, plate etc complete of size 105x60mm all as specified including one shop coat of priming and two coats of synthetic enamel paint and filling PCC 1:2:4 type-B0 (using 20mm graded crushed stone aggregate) in the frames complete all as specified and directed.

S&F pressed steel frame for doors with one or more rebate including necessary fixing lugs, hings, lock strike, plate etc complete of size 125x60mm all as spd including one shop coat of priming and two coats of synthetic enamel paint and filling PCC 1:3:6 type-B0 (using 20mm graded crushed stone aggregate) in the frames complete all as specified and directed.

S&F factory made single extruded WPC solid door Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm², modules of elasticity 900 N/N/mm² and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. .

S&F 30 mm thick factory made single extruded WPC solid plain flush door shutter comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/N/mm², modulus of elasticity 850 N/N/mm² and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk stainless steel screws all as per direction of Engineer-In-Charge.

S&F 35 mm thick factory made flush shutters, solid core construction, with block board core and plywood face panels on both side incl 6mm thick lipping/beading fixed with nails on all sides complete all as specified and directed.

S&F of rolled mild steel Gde Fe-410-W Gde E-250 Quality-A in roof trusses (framed), trussed, purlins crane gantries, joist, channel, steel tube, rails & fastenings & heavy brackets framimg (beam, tee, angle, coulmn, gusset plates, channel, hollow square/rectangular or flat section) including distance pieces, cleats with riveted, bolted or welded attachment etc complete all as specified and directed by Engr-In-Charge.

S&F stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F 18 mm thick factory made single extruded WPC solid plain flush door shutter for cupboard, shelves etc comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/N/mm², modulus of elasticity 850 N/N/mm² and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk stainless steel screws all as directed by Engineer-In-Charge.

S&F in repair 18 mm thick factory made single extruded WPC solid plain flush door shutter for cupboard, shelves etc comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/N/mm², modulus of elasticity 850 N/N/mm² and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk stainless steel screws all as directed Engineer-In-Charge.

S&F aluminium anodized barel tower bolt of extruded section 150mm long complete all as specified and directed.

S&F extruded aluminium alloyed handle fabricated type anodized of size 150 mm long complete all as specified and directed.

S&F 75mm size hasp and staple safety type aluminium anodised brass with mild steel hinge pin including bolt to hinge plate and fixed with screw complete all as specified and directed.

S&F aluminium alloy, anodised, sliding door 300 mm long bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F 300mm, mild steel ordinary rat tail rod pattern springs, including roller and roller plate joint through welding/bolt in metal/wooden frame to be carried out complete all as specified and directed.

S&F 100mm size medium weight mild steel butt hinge, fixed with metal surface through bolt or weld with screw complete all as specified and directed.

S&F 100mm size medium weight extruded aluminium alloy butt hinge, fixed with metal surface through bolt or weld with screw complete all as specified and directed.

M&L for preparation of newly painted wooden surface exc 10cm width or girth and applying two coats of synthetic enamel paint over one coat of primer all as specified and directed.

M&L for preparation of newly painted steel surface exc 10cm width or girth and applying two coats of synthetic enamel paint over one coat of primer all as specified and directed.

S&F powder coated anodised aluminium window shutters, aluminum section weighing 0.55 kg/m including necessary fittings for 3 track sliding/ rolling of shutter, locking arrangements, jointing cleats, glazing clips, rubber packing, anodised aluminum snap beading, screws, anodised aluminum fittings etc complete all as specified and directed.

S&F aluminum anodized power coated frame for window, ventilators of any colour, side hung one or more rebates/ sliding track including necessary fittings for sliding, jointing cleats, glazing clips, rubber neoprene packing , anodised aluminum snap beading, screw tee for section etc complete all as specified and directed.

S&F black sheet glass 5.5 mm thick ordinary quality in square or rectangular in size n.exc 0.5 sqm each in aluminum window, ventilator shutter complete all as specified and directed.

S&F 500 ltr capacity rotational moulded polyethylene 3-layer white water storage tanks (cylindrical vertical with closed top) hoisted and fixed in postition including dismantling of water tanks and 20mm dia brass float valve with brass rod complete all as specified and directed.

S&F in repair gun-metal, globe or gate valves, 20 mm dia with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

Taking up or down GI pipe 15mm bore including fittings, connection all as specified and directed.

All as per Srl item No 50 above but 20mm bore of pipe.

S&F GI tubing 15mm bore medium grade, fixed to wall/ ceiling or floor etc with all fittings incl taking down all as specified and directed.

S&F GI tubing 20mm bore medium grade, fixed to wall/ ceiling or floor etc with all fittings incl taking down all as specified and directed.

S&F 32mm bore medium grade GI tubing used as spout pipes complete all as specified and directed by Engineer-in-Charge.

S&F in repair bib taps 15mm dia chromium plated fancy type with capstan head screwed down screwed for iron pipe or for brass ferrule all as specified and directed.

S&F in repair stop valves (concealed cosk)15mm bore chromium plated alloy with butterfly handle screwed down for high pressure, screwed on both ends, fixed with iron pipe etc complete all as specified and directed.

S&F in repair stop valves or angel valve cast copper alloy 15mm bore fancy type chromium plated alloy with butterfly handle screwed down for high pressure, screed on both ends, fixed with iron pipe etc complete all as specified and directed.

S&F in repair chromium plated shower rose 25mm size with swivel joints fancy type including fixing to steel pipe or union complete all as specified and directed.

S&F in repair vitreous china squatting pan “Orrisa Pattern” white of size 580x440mm with `P’ or `S’ trap, integral foot rest including water connection to trap and flushing pipe etc complete and bedding in PCC 1:7:12 type F-2 (using 40mm graded crushed stone aggregate) complete all as specified and directed.

S&F in repair PVC low level dual flushing cistern 10ltr capacity, with syphonic, action PVC float valve, brackets and 32mm bore PVC flush pipe etc complete all as specified and directed.

S & F in repair PVC connections 15 mm size with PTMT nuts of length 600 mm complete all as specified and directed.

S&F in repair vitreous China wash basin, with pedestal white flat back, size 550x 450mm excluding taps, waste, chain and plug and porcelain stopper but including brackets and coupling complete all as specified and directed.

S&F in repair pillar taps, cast copper alloy fancy type, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe 15mm bore and fixed.

S&F in repair stainless steel towel rail 20mm dia, D type, 60 cm long with flanges complete all as specified and directed by Engr-in-Charge.

Dismantling of cast iron, PVC or SGSW drain pipes, jointed in cement mortar and taking out of trenches all as specified and directed.

S&F 200mm bore PVC (SWR) ISI marks pipes single socketed in any length with rubber ring joints fixed to wall or floor all as specified & directed.

S&F 110mm bore PVC (SWR) ISI marks pipes single socketed in any length with rubber ring joints fixed to wall or floor all as specified & directed.

S&F PVC (SWR ) bends 110 mm bore any radius ovel acess door complete all as specified and directed.

M&L for PVC (SWR ) floor trap 100 mm plain with stainless steel grating incl jointing with solvent cement all as specified and directed.

S&F stack clamps (100 mm pipe) out of 50x5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof all as specified and directed.

S&F harrison rails 20mm dia, stainless steel, chromium plated with fixing brackets, mstops, rollers etc fixed to wall with screws, PVC plug incl stainless steel knobs and brackets of required including taking down existing PVC curtain rod complete all as specified and directed.

Demolation of brick work built in cement mortar/ cement lime mortar all as specified and as directed.

M&L for brick work with fly ash brick straight curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed by Engineer-in-Charge.

M&L for brick work with fly ash brick, straight or curved on plan exc 6m mean radius built in CM 1:6 in half brick thick wall fixed complete all as spcified and directed by Engineer-in-Charge.

Taking down old steel window frame with shutter n.exc 1.50 sqm each (without taking off shutter from the frame) complete all as specified.

M&L for green marble work 14-16 mm thick (table rubbed and polished) in steps, jambs, shelves, pillars window cills, cooking platforms, stair case and like in pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade incl 15 mm thick screed bed in CM 1:4 incl demolition of existing complete all as specified and directed.

S&F in repair sinks made of stainless steel 1mm thick kitchen or laboratory with plugs,washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495mm x 420mm bowl size 410mm x 330mm x160mm complete all as specified & directed.

M&L for cement cocnrete 1:3:6, type B-1 (using 20mm graded crushed stone aggregate) as in plinth protection thickness of 75mm finishing the surface even and fair with joints to full depth at corners, along the wal and @3 meter c/c filled mastic mortar (to raise level) complete all as specified and directed.

M&L for cement concrete 1:4:8 type D-2 (using 40mm graded crushed stone aggregate) as in sub base complete all as specified.

M&L for coloured 60 mm thick PCC (M-35) factory made finished with grey glossy and pigment interlocking tiles/ paver block of shape/ size as conforming to IS 15658, joints will be filled with fine sand including dismantling old tiles/ paver block complete all as specified and as directed by Engr-in-Charge.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed by Engineer-in-Charge.

S&F machine cut kota stone slab flooring 18-20mm thick over cement screed base 15mm thick in CM (1:6) jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (with bees wax polish) including demolition existing complete all as specified and directed by Engineer-in-Charge.

M&L for non skid coloured ceramic tiles 7 to 8 mm thick joint free (square/rectangular) area of each tile exceeding 0.11 sqm to 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement or coloured cement to match including 15 mm thick screed bed in ready mix mortar and including demolition of existing tiles and screed complete all as spcified and directed by Engineer-in-Charge.

M&L for non skid coloured ceramic tiles 7 to 8 mm thick joint free (square/rectangular) area of each tile exceeding 0.18 sqm to 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in white cement or coloured cement to match including 15 mm thick screed bed in ready mix mortar and including demolition of existing tiles and screed complete all as spcified and directed by Engineer-in-Charge.

M&L for glazed ceramic coloured tiles in vertical surface of size 450X300x7mm thick joint free on and incl 10mm thick screed bed in ready mix mortar and jointed in neat cement slurry and pointed in colored cement mixed with pigment to match the coloured of tiles including demolition of existing tiles and screed complete all as speciifed and directed by Engineer-in-Charge.

M&L for chipping off existing loose, damaged concrete from RCC members of all affected RCC columns, beams, slabs and chajjas on External and internal facades, etc for providing PMM (Polymer modified cementitious mortar):- (i) Dry sub strate surface and free of debris & dust. (ii) Applying Epoxy bond coat on the sound substrate using approved spray machine & ensuring that no pin holes are visible. (In case pin holes are still visible after a coat, a second coat shall be applied to ensure absence of pin holes. (iii) Immediately after application of epoxy bond coat as above apply PMM (Polymer modified cementitious mortar) of n exc 50 mm thickness (Application of PMM shall be pre packed ready to use). (iv) PMM surface to be moist cured for three days followed by air curing in temperature as rcommended by manufacturer complete all as specified and directed. (Note: - Cost of formwork, bldg ht upto 12 mtr, shall be deemed to be included in unit rate quoted by the Contractor).

Demolition of RCC of any description upto 12m height all as specified and directed by Engr-in charge.

M&L for RCC 1:2:4 type B-1(using 20mm graded crushed stone aggregate) as in chajjas facia, shelves etc and similar work all as specified and directed.

Form work to rough finished surface of concrete flat, soffits of shelve, chajja and the like including supports over hangs all as specified and directed.

S&F 6-8mm dia and over TMT bar cut to length bent to shaps including cranking binding spirally hooping, hooking end and binding with MS wire (anealed) not less then 0.9 mm dia or securingwith clips all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n. exc 10 sq m on plan and not exc1.5 m in depth and getting out,all as specified & directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm all as specified & directed.

Removing excavated material n exc. 50m and depositing where directed at a level n. exc 1.5 m above the starting point all as specified & directed.

Demolition and breaking up old unserviceable drain pipes (salt glazed ware, AC or reinforced concrete)150 mm bore at any depth set in cement mortar includind PCC bed complete all as specified & directed.

M&L for RCC drain pipes NP3, 150mm bore including for laying pipes level or to falls in trenches on concrete bed and all necessary extra joints, waste and cutting as jointed complete with collars all as specified and directed.

M&L for 100mm, PCC 1:3:6 type C-2 (using 40mm graded stone aggregate) as concrete bed, width of concrete bedding shall exgtend laterally 15cm beyond either side of the outer dia of pipe laid to falls in trenches in any depth including packing under and haunching against the sides of SGSW/ RCC drain pipes NP3, 150mm bore after the pipes have been laid and tested including necessary shuttering and supports to concrete and for laying beds to falls complete all as specified & directed.

S&F mild steel barrel tower bolts, 200mm size stove enamelled black with bright bolt and fixed with weld/ bolt complete all as specified and directed by Engineer-in-Charge.

S&F mild steel sliding door bolts, 300mm size, plate type, stove enamelled black, with bright bolt 16mm dia with and including a minimum of 6 bolts and nuts four on bolt plate and two on staple plate or fixed with weld complete all as specified and directed.

M&L for preparation of internal wall surface in bath, kitchen, toilet upto lintle level and applying of one coat of FDOSFOC NITOCOTE SN 522 @ 0.4 ltr/ sqm complete all as specified and directed.

M&L for preparation of external wall surface in bath, kitchen, toilet upto lontel level and apply of one coat of FDOSFOC NITOCOTE SN 522 @ 0.4 ltr/ sqm complete all as specified and directed.

E/M PORTION Taking down carefully aluminium/ copper point wiring for light, fan, bell, socket of point complete fiitings such as switches, ceiling roses, pendents, regulator socket etc complete at site and making goods disturbed surfaces of walls, floors etc complete all as specified and directed.

M&L for point wiring with PVC insulated and PVC unsheathed multistranded FRLSH copper conductor cable of size 1.5 Sqmm including concealed PVC conduit with fittings and making good to the disturbed surfaces with continuous earth wire of copper 1.5 sqmm dia to common earth including provn of 3mm thick plastic laminated sheet of appropriate size and fixing on CI/MS boxes for mounting of accessories like switch sockets and regulators etc. complete all as specified for One light / Fan/ bell point controlled by one way modular switch.

All as per Srl item No 103 above but one 5 amp socket outlet on independent board.

All as per Srl item No 103 above but one 5 pin socket outlet 5 amp on same board

All as per Srl item No 103 above but one light point controlled by two way switches.

All as per serial item No.103 here-in-before but wiring with 2.5 sqmm FRLSH copper wire including earth wire 2.5 Sqmm of copper for 15 Amps 3 pin socket outlet.

M&L for sub main wiring with two runs of single core multi stranded PVC insulated, copper conductor, grade 1100 Volt, FRLSH cable of size 6 sqmm ( red for phase and black for neutral) and including electrical grade PVC conduits of desired colour not less than 1.2 mm thick and 25mm dia and 6sqmm multistranded copper conductor cable PVC unsheathed green coloured for earthing with complete accessories duly connected with earth dolly complete and taking down old unserviceable wiring complete all as specified and directed. Note :- (a) Cost of making good the disturbed surface plastering/ filling putty alongwith matching with the existing colour with approval make of distemper is deemed to be included in the quoted rate by contractor. (b) Three run of cable alongwith PVC conduit together shall be measured as single run.

S&F switch piano flush type single pole one way 5 amps complete all as specified and directed.

S&F socket outlet 3 pin 5 amps flush type complete all as specified and directed.

S&F switch flush type 15 amps single pole type one way complete all as specified and directed.

S&F socket outlet 3 pin 15 amps flush type complete all as specified and directed.

S&F switch piano type 2 way 5A complete all as specified and directed.

S&F in replacement of LED tube light fitting wall mounted with single side connection polycarbonate LED batten with aluminium housing and integrated electronic driver of capacity 20W, four feet and connection with PVC insulated twin core 23/0.0076 twisted copper cable from ceiling rose to tube light fitting complete all as specified and directed.

S&F wall /ceiling mounting LED 9/10 watt tube light fitting complete with all acessories 1x9 Watt LED , with CCT of 6000k suitable for domestic application, 240 Volts, 50 Hz, and internally pre-wired with 1.5 sqmm twin twisted flexible cable copper conductor and connection complete all as specified and directed.

S&F decorative 9W, LED wall mounting fittings complete set including 9W LED lamp 9 Watt polycarbonate type B-22 complete all as specifed and directed.

S&F PVC insulated sheathed copper wire 1.5 sqmm FRLSH single core 1100 volt for inverter connection in same conduit all as specified and directed

S&F fan regulator electronic type 5 step 100 watts, 240 volt and connecting complete all as specified and directed.

S&F bell, AC, 230 volts, single pole complete all as specified and directed.

S&F bell push flush type 6 Amp complete all as specified and directed.

S&F lamp holder, PVC/ polycarbonate type insulated body with back plate suitable for batten / angle fittings complete all as specified and directed.

S&F ceiling rose, surface bakelite 65x50mm three terminal all as specified and directed.

S&F in replacement GI pipe bracket made out of GI pipe light grade 32 mm bore and bent to shape 1.5m long, MS clamps made out of MS flat iron of size 32mm thick with nuts, bolts and washers complete including dismentling the existing GI pipe bracket and drilling of holes for nuts and bolts etc complete all as specified and directed.

S&F LED street light fitting 35 Watt 230V AC outdoor type with high pressure die cast aluminum housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed.

Supply and fixing in repair sheet metal enclosure for DB’s when MCB’s to be used of 240 volt 8 way with 200 amps rated bus bar SPN double door complete all as specified and directed. (Note :- All the connection of incoming and out going wire in MCB will be made with thimble with suitable size as directed).

S&F in repair MCB single pole 6 amps to 32 amps, complete all as specified and directed.

All as per Srl item No 126 here-in-before but single pole and neutral 32 amps complete all as specified and directed.

M&L for replacement of distribution board made out of CRCA sheet DB vertical type double door TPN 4 Way MS sheet including fixing in the wall, cutting chases, grounting and necessary patch work and white wash to match with the existing including making connections all as directed containing the folowings:- (Note :- All the connection of incoming and out going wire in MCCB and MCB will be made with thimble with suitable size as directed. (a) MCCB 4 pole 63 amps 16 KA breaking capacity with thermal release: 01 No (In coming). (b) Bus bar made out of aluminium duly insulated wire adhesive tape RYB & black :4 Nos. (c) MCB SPN 40 Amp- 4 Nos, MCB SP 40 Amp- 04 Nos (out going). (d) Connection from MCCB to bus bar will be made with aluminium strip of suitable size as directed.

M&L for earthing complete with galvanised steel earth plate electrode 60cm ×60cm × 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised iron earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No.3 connected to earthing test point including testing on completion including watering GI pipe 20mm bore medium grade, 15mm bore light grade GI pipe for protection of earth lead including provision of concrete pit in PCC (1:3:6) type C-1, pre-cast RCC (1:2:4) MS bar funnel & wire mesh, excavation and earth work in any type of soil including dismantling existing earthing complete all as specified & directed by Engr-in-charge.

A Schedule of Credit for old/unserviceable demolished/ dismantled items has been catered for in the tender. The Schedule of Credit is pre-priced by MES. The final amount of the tender shall be arrived at after deducting the total amount of Schedule of Credit Rs. 96,206/- from the total amount of BoQ as per General Summary sheet catered for after Schedule of Credit.

Harbhajan electric co (BID ID -3468707)

BISHAN DASS (BID ID -3468823)

s.v and co (BID ID -3468931)