Replacement of 359 Nos. steel channel sleepers at Br. No. 151 DN, 170 DN, 177 DN by H-Beam steel sleepers under Sr.DEN-III/LKO.

Maintenace works

Item- 01 Chapter no: 06 (Sleepers and Fittings Renewal)

S No. Item Description of Item Unit Qty Rate Amount

LUCKNOW-NR-DIVISION-ENGINEERING/NORTHERN RLY

Pulling & positioning of rails accurately on cess

including supporting rails, providing required

gap and squaring at ends for renewal

preparation, as directed by Engineer in-charge.

Dismantling and removing rail of all section &

length from track, laid on any type & density of

sleeper by removing fish plates, fastenings &

fish bolts and other materials including stacking

all released materials within an average

distance of 500 metres as directed by Engineer

in-charge. Note: 1.Cutting of rails shall be paid

separately. 2.Work to be done under traffic

2 061022 For Casual/Scattered Rail Renewal work RM 500.00 40.73 20365.00

Insertion of rails of all types & length in track,

laid on any type & density of sleeper to the

specified gauge under traffic block. Rates

include fastening of rail with sleepers with

standard set of fastenings and fixing of fish

plates and bolts or, if required, providing gap for

w e l d i n g and stacking of released material

without infringement within 250m as directed by

Engineer-in-Charge. Note: Rail drilling and

cutting to be paid separately.

3 061032 For Casual/Scattered Rail Renewal work RM 500.00 43.13 21565.00

Replacement of any type of sleepers in track

with PSC sleepers lying on cess or at Bridge

Approaches for casual renewal at isolated

locations with all fittings complete to specified

gauge & cross level with contractor's tools

including packing and dressing of ballast, as

directed by Engineer in-charge. Released

materials shall be neatly stacked and handed

over at specified location within an average lead

of 250 m or near either side of Bridge

approaches as directed.

4 062031 Locations other than Ballasted Deck Bridge Each 100.00 544.17 54417.00

Item- 02 Chapter no: 08 (Deep Screening and Ballast Related Activities)

S No. Item Description of Item Unit Qty Rate Amount

Manual deep screening of Plain track/ turnouts

under traffic as per procedure prescribed in

IRPWM, June 2020 or latest, in other than PSC

sleepers of any density and throwing away

screened muck arising out of screening on toe of

bank or on cess, if low or on spoil banks above

top of cutting (including throwing and leveling, if

required beyond minimum 5m from the edge of

cutting which are up to 3m deep or alternatively

carting it up to 50m for disposing it off beyond

cutting or platforms) as per direction of Engineer

in-charge, including cutting cess for effective

drainage on both sides, one round of kutcha

packing with screened ballast and further

attending to track parameter to make track fit

for 20 kmph speed complete in all respect. Note

: Payment shall be made for length along main

line only for turnouts.

Item- 03 Chapter no: 16 (Small Track Machines)

S No. Item Description of Item Unit Qty Rate Amount

LUCKNOW-NR-DIVISION-ENGINEERING/NORTHERN RLY

Quick cutting with abrasive rail cutter of all

types of rail sections including wear resistant,

head hardened rails up to 110 UTS, with

contractors tools & plants, equipment,

consumable with all lead & lift etc. complete as

directed by Engineer in-charge. Abrasive Rail

Cutter will be as per RDSO Specification No.

TM/SM/1 (Rev. 01 of 2012) with latest status of

RDSO; Rail Cutting Wheel Abrasive Disc will be

as per RDSO Specification No.TM/SM/2 (Rev. 01

Drilling holes of 16 mm to 32 mm dia. with Rail

Drilling machine including chamfering with

appropriate chamfering tools in all types of rail

section with contractor's tools & plants,

equipment, consumable with all lead & lift etc.

complete, as directed by Engineer in-charge.

Rail Drilling Machine will be as per RDSO

Specification No. TM/SM/3, dated 24.04.1991.

Item- 04 Chapter no: 17 (Handling of Materials)

S No. Item Description of Item Unit Qty Rate Amount

Loading of 52kg / 60kg PSC normal line and

special sleepers up to 2.75 metre length in

Depot / Station / Mid-section between stations in

a neat manner to departmental material train

(DMT) or contractor's / Railway's Truck/Trailer

with crane or any other means including

crossing of one track with free lead up to 250

metre and lift up to 5 metre, if required with

contractor's labour, tools & plants, machinery,

consumables etc. Note: In case of any damage

to sleeper during loading, penalty @ 50% of the

all inclusive cost of sleeper shall be levied.

1 172014 In Wagon where mechanical handling is possible MT 35.00 91.66 3208.10

a n d traffic block is not required or in Truck /

Transportation of Rails, sleepers, switches,

crossings, SEJs and Glued Joints by road vehicles

for different leads. Note: 1 . Lead shall be the

shortest motorable road length between the

points of loading and unloading. 2. Loading and

unloading shall be paid extra under relevant

9 172058 Extra for every Km per MT beyond 150 Km over MT-Km 1000.00 3.24 3240.00

item no. 172057

LUCKNOW-NR-DIVISION-ENGINEERING/NORTHERN RLY

Unloading of 52kg / 60kg PSC line and special

sleepers up to 2.75 metre length in Depot /

Station / Mid-section between stations in neat

manner for Railway usage from departmental

material train (DMT) or contractor's / Railway's

Truck/Trailer with crane or any other means

including crossing of one track and lead up to

250 metre & lift up to 5 metre with contractor's

labour, tools & plants, machinery, consumables

etc . Note: In case of any damage to sleeper

during loading, penalty @ 50% of the all

inclusive cost of sleeper shall be levied.

Item- 05 Chapter no: 19 (Bridge Related Activities)

S No. Item Description of Item Unit Qty Rate Amount

1 192010 Removing existing Channel/H-Beam sleepers Each 359.00 321.19 115307.21

with fittings from the running track under traffic

block for TBTR & stacking the same neatly at

specified places with contractor's tools & labour,

as directed by Engineer in-charge.

2 192030 Inserting in track Steel Channel/H-beam sleepers Each 359.00 373.10 133942.90

with all Railway supplied fittings complete for

TBTR work to specified gauge under traffic block

with contractor's tools including aligning,

levelling to make track fit for 20 kmph speed

and as directed by Engineer in-charge. Note:

Transportation of track material if supplied

beyond 250m of bridge approaches, shall be

paid separately under relevant item.

3 193020 Renewal of existing running rail and guard rails TRM 500.00 827.52 413760.00

of all sections on bridge portion over Steel

Channel sleepers/PSC sleepers under traffic

block including leading of new rails, fittings,

refixing all the fastenings as per approved

drawings including cutting of rails, drilling of

holes to running and guard rails as required as

per drawing and leading back the released rails

and fittings and stacking at nominated place

clear of infringements with all leads & lifts tools

and consumables complete and as directed.

4 194010 Manufacture of flared portion of Guard Rail by Set 3.00 5066.23 15198.69

cutting and bending to required shape & RDSO's

approved drawings. Note: (1) Rails shall be

supplied by Railways. (2) One set consists of two

rails i.e. both left and right.

5 194020 Providing and fixing of flared portion of guard Set 3.00 4200.46 12601.38

rails of any rail section over PSC sleepers

including fixing of with all fittings, including

leading of rails and fittings, squaring and

adjusting spacing of sleepers as required,

providing nose blocks duly cutting wooden

blocks supplied by railways and fixing it with

bolts of 16mm dia as directed complete and

finished as per RDSO's approved drawing. Note:

1.One set consists of LH & RH side rails of one

end. 2.Required P.Way fittings will be supplied

at SSE stores depot.

6 194030 Drilling holes 25mm to 40mm dia. with drill twist Each 1436.00 68.98 99055.28

in the foot of guard rails for fixing guard rails on

bridge as directed.

LUCKNOW-NR-DIVISION-ENGINEERING/NORTHERN RLY

7 194040 Drilling of 25mm to 40mm dia. holes in PSC Each 250.00 166.07 41517.50

sleepers with suitable rotary hammer / drilling

machine at indicated location for fixing of guard

rails on bridges & its approaches as per

approved drawing and fixing of contractor's

HDPE dowels and adhesive of approved quality

to Drawing no. RDSO/T-3002, procured from

RDSO's approved sources with contractor's

materials and consumable.

8 194060 Dismantling of existing flared portion of guard Set 3.00 2339.38 7018.14

rails of any rail section over PSC sleepers duly

removing rails & fastenings and leading and

stacking released materials at nominated place

within free lead, clear of infringements,

complete and as directed. Note: One set consists

of LH & RH side rails of one end.

9 195020 Fabrication & supply of Galvanized H-beam MT 51.00 145084.47 7399307.97

Sleepers made out of the materials confirming to

IS 2062 of standard Rolled sections as per

approved drawing Nos RDSO/B/1636/4/R,5&9

complete and as directed by Engineer-in charge.

Note: Cost of steel fittings and GRSP shall be

paid separately.

Supplying & fixing of Anti-Skid MS / Stainless

Steel chequered plates on un- ballasted deck

bridge as per approved drawings, with matching

grade stainless steel fasteners as directed by

Engineer-in- Charge, on new bridge or

replacement of existing chequered plates on old

bridge including removal of old chequered plates

and stacking near approaches of bridge, clear

from all infringement. Note: Joints of chequered

plates shall not fall in between sleepers

10 195042 MS chequered plates 6 to 8mm thick including Kg 5000.00 88.76 443800.00

removal of existing chequered plates on Bridges.

NOTE: Payment shall be made only as per

weight of new Chequered Plate fixed.

11 195060 Clearing waterway of major & minor bridges by Metre 100.00 245.14 24514.00

removing weeds / shrubs / bushes, removing silt

deposit, filling scours, if any up to 10 metre from

centre of bridge on either side including

disposing waste and silt away from waterway.

Note: Rate is for a single line and per metre of

12 195070 Fabrication, supplying and fixing 600mm x Each 6.00 3836.96 23021.76

450mm Bridge Board made from 16 SWG MS

Sheet duly welded or riveted to back support of

two 600mm long horizontal angles of size 25mm

x 25mm x 3mm & two numbers 2.5 metre long

vertical support of MS Angle of size 50mm x

50mm x 5mm, welded / rivetted to board.

Vertical supports shall have split ends for proper

fixing in ground. Vertical supports of board shall

be embedded in ground in M 20 Cement

Concrete blocks of size 300mm x 300mm x

300mm, complete job including painting &

writing of subject matter on bridge board, as

directed by Engineer - In charge Note:

Excavation & concrete work will be paid

Item- 06 Chapter no: 20 (Supply of P. Way Materials)

S No. Item Description of Item Unit Qty Rate Amount

1 201010 Manufacture and supply of Hook Bolt 28mm dia. Kg 4667.00 307.33 1434309.11

& 320mm long as per RDSO Drg. no. BA-

1636/I/R2 from RDSO approved sources

LUCKNOW-NR-DIVISION-ENGINEERING/NORTHERN RLY

2 201020 Manufacture & supply of 10mm thick Grooved Set 450.00 450.39 202675.50

Rubber Pads as per drg. No. RDSO/T-5199 &

RDSO's Spec. no. IRS-T-47-2006 (Prov.) from

RDSO approved sources with all contractor's

lead, lift, labour, tools, plant and transportation

etc. complete as instructed by Engineer in-

charge. Note: One set constitutes two nos.

3 201040 Manufacture & supply of a set of 2 Nos of Set 450.00 2318.21 1043194.50

Elastomeric Pads 25mm / 30mm thick and 4 nos

of Grooved rubber pads as per RDSO drawing

No. B/1636/5 alt 2 to suit Insulated H Beam

sleepers from RDSO approved sources with all

contractor's material, lead, lift, labour, tools,

plant and transportation etc. complete as per

approved drawings and as instructed by

Engineer in-charge. Note: One Set consists of 2

nos. Elastomeric Pad 25mm/30mm and 4 nos.

Grooved Rubber Pad.

4 201060 Manufacture, supply & fixing of galvanised steel Set 50.00 3412.85 170642.50

fittings of insulated galvanised steel channel

sleeper for 60 Kg running rails & 52 Kg Guard

Rail as per RDSO drawing no. RDSO/T-5155 to

5164 with up-to-date correction slips and

specifications from RDSO approved sources with

all contractor's lead, lift, labour, tools, plant,

transportation etc. complete and instructions of

Engineer in-charge.

5 201080 Supplying of Zero toe load fixtures for H Beam Set 359.00 5119.27 1837817.93

sleepers of 52/60Kg Rails procured from RDSO

approved firms a s per RDSO approved drawing

with up-to-date correction slips and

specifications with all contractor's lead, lift,

labour, tools, plant, transportation etc. complete

as per instructions of Engineer in-charge. Note:

Complete fixture for 1 sleeper shall constitute 1

Item- 07 Chapter no: 21 (Miscellaneous Items)

S No. Item Description of Item Unit Qty Rate Amount

1 211170 Galvanisation of Railway's Chequered Plates, MT 51.00 21279.10 1085234.10

Channels, Plates, Angles, and I-Section by hot

dip process with Zinc Coating and mass of Zinc

coating shall not be less than 705 g/sqm and

galvanisation thickness shall not be less than

100 microns including necessary surface

preparation as per Clause-4 of IS:2629-1985.

Galvanisation shall be done as per IS:2629-1985

and IS:4759-1996 with Zinc conforming to

IS:209-1992, duly taking all the measures for

safeguarding against embrittlement of hot-dip

galvanised iron and steel products as per

IS:6158-1984 with all contractor's labour,

material, tools, plant, all lead, lift and crossing

of tracks etc. complete and as directed by the

Engineer in-charge.