Provn of open two wheeler parking shed at HQ GNA Goa and Provn of washbasins and bathrooms at unit shops complex INS Gomantak under GE Gomantak Vasco

Amount

Excavation in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out insoft/ disintegrated rock

M&L 75 mm thick PCC 1:3:6 type C-2, (using 40 mm graded aggregate) as sub base of floors complete all as specified.

Material &Labour for Cement concrete Type D2 1:4;8 40mm graded aggregate as in foundation filling and mass concrete.

Pre-cast cement concrete block masonry Type C1 1;3;6 20mm graded aggregate with solid blocks, exc. 10 cm in width and setting in mortar 1:6, complete all as specified.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc flat rough finished surfaces

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) of rough finished flat surfaces

Formwork to sides of pillars, posts, struts, piers, columns and stanchions

M&L TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

M&L TMT bars 6 to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips for stirrups, spacers and binders

Material & Labour for RCC (Nominal Mix) type B1, 1:2:4 (using 20 mm graded aggr) in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like.

Material & Labour for RCC (Nominal Mix) type B1, 1:2:4 (using 20 mm graded aggr) as in lintels/roof beams

Material & Labour for RCC (Nominal Mix) type B1, 1:2:4 (using 20 mm graded aggr) as in plinth beams

Material & Labour for RCC (Nominal Mix) type B1, 1:2:4 (using 20 mm graded aggr) columns,pillars,piers,posts etc

Material & Labour rendering 15 mm thick cement plaster C M 1:6 on fair faces of concrete or brick surfaces finished even and with smooth without using extra cement

Material & Labour for providing two coats of oil-bound distemper over a coat of alkali-resistant primer on new plastered surfaces including necessary preparation to surfaces complete all as specified and as directed

Material & Labour rendering (10+5) mm thick on brick or concrete surface in cement plaster C M 1:4 using WPC on fair faces of concrete or brick surfaces finished even and smooth without using extra cement. Note Water Proofing Compound shall be measured sepaterly.

Material and Labour two coats of acrylic emulsion exterior paint (anti fungal painting-APEX) over one coat of pimer on new plastered surfaces

Material & Labour rendering 5mm thick cement plaster 1:3 on ceiling to be finished even and smooth without using extra cement.

Material & Labour 03 coats of white wash on newly plastered surfaces including preparation the surfaces of ceiling

Material & Labour Hardcore (broken stone boulders) of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface.

Material & Labour for 75 mm thick PCC type D-2, 1:4:8 (using 40 mm graded aggregate), as in sub base of floor.

Material & Labour for 25 mm thick PCC type B-0, 1:2:4 (using 12.5 mm graded aggregate), as in sub base of floor

Material & Labour 20mm thick screed bed or bedding layer of cement mortar 1:4 for laying floor finishes.

Materila & Labour for Non Skid ceramic coloured tiles 7 to 8mm thick (Square/ rectangular) area of each tile exceeding 0.18 Sqm but not exc 0.38 Sqm set and jointed in neat cement slurry and pointed by matching cement in floor

Material &Labour rendering 10mm thick cement plaster C M 1:6 on fair faces of concrete or brick surfaces to finished smooth and even without using extra cement

Glazed ceramic colourd tiles in vertical surface 10 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match in floor

Returning, filling in , including, spreading, levelling, watering and well ramming in layers not exc 25cm deep as in soft/ disintegrated rock complete all as soecified and directed

Material & Labour for 75 mm thick PCC type C-2, 1:3:6 (using 40 mm graded aggregate), as in plinth protection incl necessary form work etc complete.

M&L Sand filling under floors or in foundations including watering and consolidation

Supply & Fixing CPVC 20 mm outer dia pipes SDR 11 including concealing in walls & plain CPVC SDR 11 fittings on walls/ ceilings or laying in floors complete all as specified

Supply & Fixing CPVC 25 mm outer dia pipes SDR 11 including concealing in walls & plain CPVC SDR 11 fittings on walls/ ceilings or laying in floors complete all as specified

S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-1 for 1000 ltrs capacity

S&F 20 mm dia ball brass valve,high pressure with polythene float and fly-nut complete, screwed for iron pipe or brass ferrule

Supply & Fixing PVC (SWR) floor trap 63 mm dia , plain with grating including jointing with solvent cement

Supply & Fixing Tubular towel rail, 20mm dia, D type, 60cm long Brass chromium plated between flanges

Supply & Fixing Bib taps,long body 15mm dia, chromium plated fancy type, with capstan head handle, screwed down, screwed for CPVC pipe or for brass ferrule.

Supply & Fixing Stainless steel soap dish standard size heavy duty

Supply & Fixing Pillar taps, 15mm dia, cast copper alloy, fancy type with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe.

Supply & Fixing PVC connections 15 mm size with PTMT nuts of length 450m fixed in repair

Supply & Fixing CP stop cock(angle cock), 15mm dia, fancy type with capston heads screwed both ends for iron pipe or for unions .

Supply & Fixing CP health faucets including flexible hose,wall hook

S&F in repair Vitreous china wash down water closet pan (pedestal pattern), white excluding fixing bolts, flushing cistern and flush pipe including 10 ltr capacity PVC valveless, syphonic action type, flushing cistern, low level ,white, with inlet ball valve, float and handle including brakets

S&F in repair vitreous china wash basins, size 550x400mm white flat back including cutting for and pinning in ends of brackets or erecting stand including 32mm waste fittings, chromium plated with long screwed shanks & fly-nuts, flange end bedded in red lead cement and other end fixed

Supply & Fixing Low density polyethylene pipes 40mm dia of pressure rating 6Kgf/cm2 fixed complete to walls, ceilings, or in floors etc

Supply & Fixing grating doom 100mm dia of stainless steel.

Supply & Fixing Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe)

Supply & Fixing 20mm dia Concussive push button taps of cast copper alloy, screwed for iron pipe and fixed

Material & Labour for rendering 10 mm thick in cement mortar 1:4 mixed with WPC 3%by weight of cement , on concrete slab roof top surfaces finished even and smooth without using extra cement, complete all as specified.(Liquid WPC will be measured seperately)

Material & Labour for water proofing treatment using 4 mm thick APP modified membrane consisting five layer membrane with features as specified weighing not less than 4.00 Kgs per Sqm laid over a coat of cold applied bituminous primer @ 0.4 Liters per sqm on surface provide, a layer of APP modified membrane by torching applications including sealing the over lap while torching with 100 mm on length side and 100 mm wide side as per manufacturer instructions including joints and changes in direction be curved with cement mortar 1:3 mixed with SBR latex @ 200 ml/bag of cement curved well before laying of membrane all as per manufacturer instructions and provide a finishing coat with solar reflective bitumenous aluminum paint @ 0.1 Kgs per sqm as per manufacturer's instructions and to the satisfaction of Engineer-in-Charge. Note (i) Irrespective of lap the net covered area shall only be measured for payment. (ii) The quoted rate is deemed to be inclusive of primer, APP membrane and SBR Latex.

Supply only Liquid water proofing compound

S&F solid PVC door frame of size 50 mmx47mm made out of 5 mm plain coloured PVC sheet reinforced with MS square tube complete all as specified

S&F solid PVC moulded door shutter with particle board core,28 to 30 mm thick(stiles) with 2 raised panels designed with 2mm thick moulded PVC sheet on the front face and 2 mm thick plain colour PVC sheet on back face complete all as specified.

Supply & Fixing Butt hinges, 100mm long, medium weight, stainless steel.

Supply & Fixing Aluminium, anodised barrel tower bolts 150mm long of extruded section and fixed

Supply & Fixing aluminium alloy anodised sliding door bolt 250mm long with hasp, staple and fixing clips of sheet, cast or extruded sections and fixing bolts

Supply & Fixing powder coated aluminium sections for doors, windows, ventilators including joining cleat for fixing etc complete all as specified .

S&F cast iron nahani trap with steel grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4)

M&L 100 mm dia Cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4)

Supply & Fixing 4mm thick sheet glass ordinary quality and glazing with oil putty, exc 0.5 sqm in each pane

Supply and fixing aluminium anodized wire mesh of size 1.50mmx3mm and 20 G thick as specified.

Supply & Fixing powder coated grill of make DG 104 (6.5mm thick) sections and mesh size 80mm x 60mm (minimum powder coating 50 microns)

Supply &Fixing 110 mm dia PVC(SWR) pipe with all special accessories. Complete all as specified & directed.

Supply &Fixing 75mm PVC (SWR) vent cowl complete all as specified & directed.

Supply &Fixing 125 x 110 mm PVC(SWR) gully trap complete all as specified & directed.

Material & Labour for 25 mm thick PCC type B-0, 1:2:4 (12.5 mm graded aggregate) as in levelling course in floors

M&L Chequered cement concrete tiles(Rubberised) 30cm x 30cm x 25mm thick, set, jointed & pointed in neat cement slurry in floors with white cement & pigment, as specified and dircted by Engr-in-Charge.

Excavation over areas n exc 1.5 m deep and getting out in soft/disintegrated rock for foundation. all as specified and directed by Engr in charge.

M&L Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade with grey cement and pigment all as specified and directed by Engr in charge.

S & F rolled mild steel as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy brackets framing (Beam, tee, angles, channel or flat sections) including distance pieces, cleats etc. (Fe- 410-W (Gde E-250 quality A)

M&L for preparation of new steel surfaces and apply two coat of Anti corrossive paint over a coat of anti corrossive primer all as specified and directed.

S & F pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering cladding to wall fixed with self tapping screws as specified .

M & L two coats of cement based paint over a coat of alkali resistant primer including preparation of new plastered surfaes.

Removing excavated rock/soil exc 50m but not exc 250m and depositing where directed at a level n exc 1.5 m above the starting point.

M&L for point wiring complete with 1100 volts grade PVC insulated and unsheathed multistranded 1.5 Sqmm FRLS single core copper conductor cable drawn through and including PVC conduit concealed in wall with all accessories, & sunken pressed steel terminal boxes made out of 2 mm thick MS sheet concealed in walls with 3 mm thick laminated Hylem sheet top cover fixed with brass screws for housing switches, socket, regulator etc including 1.5 Sqmm PVC insulated and unsheathed mutistranded copper conductor cable as earth continuity wire all as specified for one light, exhaust fan, socket outlet etc.

All as per serial item No 76 here-in-before but one 5 pin switch socket outlet 5 Amps on independent board controlled by one switch.

S&F switch piano flush button single pole one way 05 Amps

Supply and fixing switch socket combination 2 in 1, 3/5 pin 5 Amp flush type universal.

S & fixing ceiling rose, surface Bakelite 65x50 mm Two to three terminals.

Supply and fixing 25W 4ft long LED batten light fitting with 2.5 KV voltage surge protection ,PF >0.9 complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor cable of suitable size .Make Bajaj: Product Code 830258 (4FT 25W CDL IVORA) or Equivalent in Philips/Havells

S & Fixing Submain wiring with 4 sqmm 2 Runs of single core multi stranded PVC in related unsheathed cable 1100 Volts with copper conductor drawn in and including 25 mm wide non metallic rigid conduit with all accessories such as tees, elbows, junction box Reducers etc as required along with 1 Run of 4 sqmm single core PVC insulated unsheathed copper conductor as continuous earth wire connecting to Distribution Board and testing on completion all as directed.

Supply and fixing sheet metal enclosure (DB) SPN,4 way ,240 V double door with 100 Amp rated Copper bus bar for MCB's with IP 54- IK 09 complete.

Supply and fixing MCB, single pole & Neutral, 6-32 Amp, 240 Volts, 'C' Curve 10KA.

Supply and fixing MCB, single pole, 6-32 Amp, 240 Volts, 'C' Curve 10KA.

S & F LED Bulkhead luminaire 10W ,IP 65 including LED Bulb/lamp complete .

Material and labour for earthing complete with galvanised steel earth plate electrode 600mm x 600mm x not less than 6mm, burried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of earth plate not less than 1.5m below normal ground level, connected to galvanised earth lead wire 4.00mm dia by means of bolts , nuts, check nuts and washers of GI/steel all as shown in electric plate No 3 connected to earth test point/MCB DBs all as specified and indicated complete and including charcoal dust ,salt etc and GI protection pipe medium grade 15 mmand GI watering pipe 20mm medium grade with funnel and wire mesh,40 mm thick precast RCC M-15 (Nominal mix) cover reinforced with XPM weight not less than 4 kg/sqm with suitable handle of 6mm dia MS bar and angle iron 40x40x3mm frame for cover, PCC M-15(Nominal mix) pit, excavation and earth work in any type of soil and connected all as specified and directed by Engineer-in-Charge.

S & F Exhaust fan Metal body of size 225 mm sweep with air delivery 750CMM , 1400 RPM complete including fastening studs ,nut bolts etc and louvers of suitable size.

S & F LED batten fitting 10 Watts ,2 ft long ,plastic body complete .

Supply, Laying, joining & testing LT XLPE Insulated & sheathed armoured electric cables with multistranded aluminium conductor cable 1100 volts grade, laid in trenches/ ducts or fixed to poles/walls or laid under roads/paths/drains/culverts duly encased in galvanised steel pipe of suitable sizes including cable gland of suitable sizes & aluminium lugs for connection for cross- sectional area 6 Sq mm 2 Core complete all as specified and directed.

Excavation in trenches in hard/dense soil n. exc. 1.5 meter wide and n. exc. 1.5 mtr depth and getting out, including trimming the sides and forming bottom surface to required levels for laying cables etc complete all as specified.

M & L for fine river sand for cushioning in layers of sand 8 cm before laying of cable & 15 cm after laying of cable (total 23 cm ) in trenches, duly punning to a thickness of 18 cm for cable protection complete all as directed and specified. Note:- Thickness after punning shall be measured for payment

Supply and laying PCC cable cover class LV type 1 flat size 250mmx150mmx40mm for protection cover to under ground cable.

Returning filling in including spreading levelling watering and well ramming in layers not exceeding 25 cm in thick using excavated hard/dense soil.

Supply and fix GI tubing (light grade) with all fittings,laid in trenches, or fixed along with walls /poles,bore of pipe 40mm.

Supply & Fixing GI tubing, medium grade, ISI marked complete with all fittings, laid in trenches or laid under floors, fixed on walls with and including providing clamps etc complete all as specified & directed, for the following size:-

a) 25mm dia bore

b) 20mm dia bore

Supply and fixing of Gun metal gate valves (ISI marked) of size 20mm dia with iron wheel head,screwed both ends complete all as directed by Engineer-in-charge .

M/S jvsr constructions

M/s Gayatri Contruction Co.

Tara Construction