SPL REPAIR TO FENCING AND GATE AT OFFRS MD ACCN OF VRC ENCLAVE AND PROVN OF 01X ROOM ALONGWITH POINT CONNECTION IN FRONT OF TEMPLE OF HQ MB AREA UNDER GE (WEST) JABALPUR

Amount

Demolition of cement concrete in ground floor & pavings n. exc 15 cm thick (below or above GL) unreinforced complete all as specified and as directed.

Demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches, excluding ashlar facings including precast concrete articles etc complete all as specified and as directed..

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

Dismantling posts or strut ( wooden, steel or RCC ) of length exc 1.00 RM and not exceed 2.5 RM ,any type including taking down embeded portion and making good to disturb portion of ground complete all as specified and as directed.

Taking down wooden frames with shutter / Jafri gate (without taking off shutters from the frame) n exc 10 sqm each and removing to store complete all as specified and as directed .

M&L for Brick work using fly ash modular bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:4 complete all as specified and as directed.

M&L for 15mm thick rendering in cement mortar (1:4) on brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed. Note : WPC shall be measured and paid separately.

M&L for applying two coats of cement base paint over a coat of primer on newly plastered surfaces of walls including preparation complete all as specified and as directed.

M&L for cement concrete type C-2 1:3:6 (using 40 mm graded stone aggregate) as in post holes filling complete all as specified and as directed.

M&L for PCC 1:4:8 type D2 9using 40 mm graded stone aggregate) as in foundation, filling and mass complete all as specified and as directed.

S&F for Framed work as in doors or gates of angle/ MS tube or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing conforming Fe-410W(GdeE-250) quality B complete all as specified and as directed.

S&F for 1.25mm thick mild steel, plain, black sheet in hearths; covering to door shut ters; covering to door chowkats (frames); chullah hoods; water tanks; water troughs; ducts; urinal troughs and funnels, etc. cut to size edges beaded if directed, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel members, etc., with plain 40 mm lap joints or welded/ riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc. as required complete all as specified and as directed.

S&F for Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and as directed.

S&F for Mild steel posts and struts as in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., conforming to Fe 410-0 or Fe 310-0 complete all as specified and as directed.

S&F for Mild steel screw bolts 10mm dia (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt n exc 10cm complete all as specified and as directed.

M&L for applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer on new steel surfaces including preparation complete all as specified and as directed.

Dismantling of wire fencing of any description complete all as specified and as directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified and as directed.

Supply only Chain link MS galvanised fencing of 4 mm dia and mesh size 75 mm x75 mm complete all as specified and as directed.

S&F in repair Galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. complete all as specified and as directed. (Note: Each line wire to be measured)

M&L for applying two coats of synthetic enamel paint over a coat of zinc oxide primer on new steel surfaces of any description not otherwise described n exc 10cm in width or girth including preparation complete all as specified and as directed.

Excavating in post holes (or similar holes) in soft/loose soil each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50 m and making good surface complete all as specified and as directed.

Supply only Liquid water proofing compound complete all as specified and as directed.

Excavation in trenches n. exc 1.50 metre wide and n. exc 1.50 metre deep for foundation and n. exc 10 Sqm on plan area as in soft/loose soil and getting out complete, all as specified and as directed.

Returning filling in, including, spreading, leveling watering and well ramming in layers n exc 25 cm thick each, complete, all as specified and as directed.

Removing excavated soil to a distance n,exc 50 mtr and depositing where directed at a level n.exc 1.5 mtr above the starting point complete, all as specified and as directed.

S&F for steel work in tubular trushes including special shaped washer etc complete using ERW or induction but welded tubes confirming to I.S. 1161-1979 grade St. 240 etc complete all as specified and as directed.

S&F, for Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete, all as specified and as directed.

S&F for Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm of an colour having tensile strength of 550Mpa as in roof covering/cladding/ ridge to wall, fixed with self tapping screws complete all as specified and as directed.

M&L for machine cut cudappa stone slab 20 to 25 mm thick over and including cement screed base 15mm thick in CM 1:6 in floors laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M&L for MS work as in wind ties for roof including securing bolts, drilling holes, notching for wire etc complete, all as specified and as directed.

S&F for vitreous china wash down water closet pan (Padestal pattern) white excluding fixing bolts, flushing cistern and flush pipe with and incl 'P' or 'S' trap and making good to floor to match with existing complete all as specified and as directed.

S&F for vitreous China squatting pan of pattern Orissa Pattern , size 580 x440 mm white with P or S trap , front or backinlet and integral foot rests any pattertn (excl flushing cistern and flush pipe) complete incl provn of lime concrete bedding connection to flush pipe , trap etc & making good complete all as specified and as directed.

S&F for High or low level PVC fluslhing cistern 10 litres capacity valveless ,syphonic action type low level flushing cistern ,white including flush pipe, cantilever brackets ,inlet, ball valve, float and handle, PVC connection 15mm dia, 450mm long etc (exclusive of brackets), and connections to pipes and fixing of chain and pull, or lever complete all as specified and as directed.

S&F for grating doom 100mm dia CP (Min weight 25 grms) complete all as specified and as directed

M&L for glazed ceramic coloured tiles of size 450 x 300 x 6 to 7 mm,450x350 or 350x250 6 to 7mm thick on vertical surface such as skirting/dado etc. ,set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile with & including 10 mm thick rendering in cement mortar 1:4 finished rough to fix tiles complete all as specified and as directed

M&L for 10mm thick Virified Ceramic tiles dark shade (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM (1:6) complete all as specified and as directed.

M&L for 15mm thick rendering on brick work or concrete surface in CM 1:6 finished fair& even surface complete all as specified and as directed.

Cutting chases, pinning in. through brick walls and making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and directed.

M&L for 18-20mm thick black zed granite stone slab machine cut in skirting/dado, cooking platform, jams, pillars, windows cills and the like laid over and including 10mm thick screed bed or backing coat in cement mortar (1:4) and jointed with grey cement slurry and pointed with white cement and with admixture or pigment to match the shade of granite stone including grinding and polishing complete all as specified and as directed.

Rounding to edges of stone slabs one edge, such as steps, cooking platform, and other similar situations complete all as specified and as directed.

S&F for stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed.

S&F for 15 mm dia bib taps cast copper alloy with Chromium plated cruch or butterfly handle scrwed, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed.

S&F for 15mm bore dia angular stop valves chromium plated fancy type, long shank, screwed down , high pressure ,screwed both ends for iron pipe or for union and fixed complete all as specified and as directed .

S&F for stop valves 15mm , cast copper alloy , fancy type chromium palted screwed down , high pressure , with crutch or butterfly handle , screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.

S & F for Towel rail 600 mm long and 20 mm dia brass chromium plated D type fixed with screws and wooden or plastic cleats complete all as specified and as directed.

S & F for gate / globe valves 20 mm bore cast copper alloy screwed both end down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union and fixed bore of complete all as specified and asdirected.

Supply & fixed PVC connection 15 mm size , 450mm long with PTMT adopter,check nuts and washer on both sides complete all as specified and as directed.

S & F for 32 mm thick PVC waste pipe of minimum length 1 mtr for kitchen sink and WHB etc complete all as specified and as directed.

S&F for Flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern including all joints and making good complete all as specified and as directed

S&F for jet spray with 1m PVC tube (stainless steel), chromium plated for vitreous china pedastal pattern water closet complete all as specified and as directed.

S&F for chromium plated, Toilet paper holder complete all as specified and as directed.

M&L for Hardcore of Broken stone or boulders gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and as directed.

M & L for 100mm thick Cement concrete type D 2, 1:4:8, using 40mm graded stone aggregate as in subbase complete all as specified and as directed.

Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors for 20mm bore of pipe including Brass elbow, Brass Tee, Male threaded brass adaptor, Female threaded brass adaptor and all necessary fittings etc complete all as specified and as directed.

Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors for 25mm bore of pipe including Brass elbow, Brass Tee, Male threaded brass adaptor, Female threaded brass adaptor and all necessary fittings etc complete all as specified and as directed.

S&F, for 75mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints fixed to walls including stack clamp complete all as specified and as directed.

S&F for 110mm bore PVC (SWR) pipes, single socketed in any length with rubber ring joints fixed to walls including stack clamp complete all as specified and as directed.

S&F, for 75mm bore PVC (SWR) bend, any radius with access door complete all as specified and as directed.

S&F, for 110mm bore PVC (SWR) bend, any radius with access door complete all as specified and as directed.

S&F for 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and as directed.

M&L for applying two coats of oil bound distemper over a coat of chalk whitining primer over 1mm thick birla wall care putty on new plastered or un-plastered surfaces of wall including preparation complete all as specified and as directed.

S&F for Health faucet brass CP with 1.20M long PVC flexible pipe with Brass/CP check nut and bracket fixed to wall complete all as specified and as directed.

M&L for 75mm thick PCC 1:3:6 type C2 using 40mm graded stone aggregate, as in plinth protection laid in panels and finished even and smooth without using extra cement including necessary form work complete all as specified and as directed.

S & F for Aluminium powder coated (minimum thickness of powder coating 50 micron) door with frame top and sides of size 83.50x44.45x1.62mm ( Section No 19549), and shutter top rail and stile of size 92x38x1.70 mm ( Section No 21339) and Lock and bottom rail of size 125x37x1.80 mm ( Section No 19634) including rubber gasket, beading, anodised aluminium snap beading, screws, anodised aluminium fittings such as butt hinges/Pivot hinges 100 mm long (3 Nos.), handle (2 no.), Lock 06 Lever and locking arrangement ,fixing 5.00 mm thick glass with necessary rubber beading gasket etc including necessary plaster, painting ,cill and making good to disturbed portion complete all as specified and as directed.

M & L for Aluminium powder coated( minimum thickness of powder coating 50 micron) sliding windows (three track) of frame of size bottom section 92.00x31.75x1.50mm ( Section No 20832),Top and Sides of size ( Section No 20831) with anodised aluminium shutters Top and bottom size 40x18x1.55mm (section 20736) and sides ( handle) of size 40x18x1.55mm (section 20738) and lock side shutter frame size 40x18x1.45mm (section 20737) including rubber gasket,beading and locking arrangement , both glazed and gauzed with 5.0 mm thick glass, stainless steel wire cloth netting(0.36mm nominal dia and averege width of aperture 1.40mm), and fixed including necessary glazing clips, rubber packing, anodized aluminiunm snap beading screws and aluminium fittings of standred size complete all as specified and as directed. ( Notes : (i) Glazing and stainless steel wire cloth will not be measured and paid for separately under relevant items of this BOQ

S & F for anodised aluminium powder coated (minimum thickness of powder coating 50 micron) Ventilator louvers type frame top and sides of size 31x42x1.6 mm ( Section No 20558) rectangular tube of size 40x20x2.0mm ( Section No 14019) and middle vertical of size 42x46.20x1.60mm ( section No 20560) and clip for fixing in wiremesh and glass of size 19x17.30x0.90mm ( section No 19360) including rubber gasket, beading, anodised aluminium snap beading, screws, handle,fixing 4.00 mm thick glass frosted glass , 0.36 mm nominal dia wiremesh with necessary rubber beading gasket etc including necessary plaster, painting ,cill and making good to disturbed portion complete all as specified and as directed.

M&L for anodised aluminium powder coating frame for doors, windows, ventilators with one or more rebates including joining cleats for fixing etc.(minimum thickness of powder coating 50 micron) complete all as specified and as directed.

M & L for snap grid false ceiling system of E board exposed suspended system, grid size 600mm x 600mm compressing of GI powder coated Main Runner of dimensions 39mm x 24mm x 0.8 mm thick to be placed in the grid system duly suspended with 4mm dia GI bar hangers fixed with steel dash through fasteners from purlins with butterfly clips (wt-0.007 kg/clip), hold down clips (wt-0.0035 kg/clip), and fixed with pre painted 4mm thick E board of approved design and with provn of light fixture complete all as per manufacturer instructions and as directed.

M&L for Birck work with Fly ash, old size sub class 'B' bricks of compressive strength not less than 75 Kg/sqcm, straight or curved on plan exc 6 metre mean radius built in cement mortar (1:6) complete all as specified and as directed.

M&L for ENDURA out door tiles 30 cm x 30 cm x 10 mm thick rubberised mould set, jointed and pointed in neat cement slurry and pointed in white on coloured cement to match as in floors etc layed over and including 15 mm thick screed bed or bedding layer in cement mortar 1:6, etc all complete all as specified and as directed.

S&F for SS Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and as directed.

Supply & Fixed for ceramic wash hand counter top basin white colour of size 700X460mmX200mm quality make approved by GE complete all as specified and as directed.

S&F for stainless steel chromium plated single lever basin mixer make approved by GE including all necessary fittings comlete all as specified and as directed.

Supply & Fixed for Towel Ring complete all as specified and as directed.

S&F for looking mirror of size 5 feet X 3.5feet with designer glass and frame to be fitted with wall including all necessary arrangements and fittings complete all as specified and as directed.

M&L for Point wiring with PVC insulated 1.5 sq mm multi stranded copper conductor cable 1100 volts grade drawn into and including concealed PVC conduit not less than 20mm (ISI marked) including all fitting and fixing accessories including sunk in cast iron/pressed steel terminal boxes duly painted with two coats of antirorrrosive paint outside and two coats of aluminium paint inside, 2.8mm thick hylam brand laminated white bakelite sheet cover for mounting of switches, sockets, fan regulators etc and PVC insulated 1.5 Sqmm multistranded copper conductor cable as earth wire and making good the disturbed surfaces to match with the existing surfaces complete all as specified and as directed.

(a) One light point controlled by one switch.

(b) One fan point controlled by one switch.

(c) One socket point controlled by one switch on same board.

S & F in repair for Switch piano flush type AC 230 volts 5 Amps single pole one way complete all as specified and as directed.

S & F in repair for Socket outlet 3 pin, 5 Amps and AC 230 volts flush type complete all as specified and as directed.

S & F in repair for Ceiling rose surface bakelite 65 mm x50 mm three terminal AC 230 volts flush type complete all as specified and as directed.

S & F in repair Smart bright Batten Series, LED luminaire using LEDs 22 watt 110 LM/watt with diffuser which ensures uniform distribution and comfort batten series features latest LEDs and delivers consistent light output, stable color start Extruded Aluminum housing, Energy efficient, Flicker free start Inbuilt driver unit Suitable for wall and ceiling mounting using brackets complete all as specified and as as directed.

S & F in repair Sheet metal enclosure DBs Single Pole and Neutral 8 way with 200 Amps rated bus bar 240 volts single pole and neutral complete double door complete all as specified and as directed.

Supply and fixing in replacement MCB single pole and neutral 240 volts 40 Amps, B Series complete all as specified and as directed.

Supply and fixing in replacement MCB/Isolators single pole 240 volts upto 40 Amps, B Series complete all as specified and as directed.

Earthing complete with galvanised steel earth plate electrode 60 cm x60 cm x 6 mm thick buried directly in ground ,(Earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meter below normal ground level ,connected to and including galvanised iron earth wire 4 mm dia by means of nut, bolts, check nuts and washers of galvanised iron or steel complete all as specified and directed including testing on completion including the material and labour of the following : - (a) Excavation and earth work for drilling hole for electrode in any type of Soil. (b) reinforced with welded steel wire fabric weighing not less than1.87 Kg/ Sq meter. (c) Funnel with watering pipe of GI 20 mm nominal bore light grade and lugs etc complete all as specified and directed (d) 15 mm nominal bore medium grade GI protection pipe 5 meter long for protection of earthing lead complete all as specified and directed. (e) Requisite quantity of common salt and charcoal. (f) Testing of earthing.

Supply & fix in replacement of LED Security Light Luminaire 35 watt 6000K with .high power LED cool white,CRI 75,+/- 5% supply voltage 220/240/50 Hz, light engine driver base.pole adapter,powder coated pressure die cast aluminium with heat resistant toughened glass with lens type,GI pipe 40 mm dia medium Grade not less than with 1.2 m.long in any shape with 2 nos of pole fitting clamps made out of MS flat , nuts and bolts and painting with aluminium paint. complete all as specified and as directed.

Supply , laying and testsilng cable XLPE insulated , screened, PVC bedded , galvanized , steel strip or wire armoured, electric power cables ( Heavy duty ) 1100 volts grade with stranded aluminium conductor of size 2 core 16 Sqmm complete all as specified and as directed.

Supply and Laying DWC pipe 38 mm ID 63 m OD for cable protection with all accessories complete all as specified and as directed.

Hemant Associate (BID ID -3320051)

ANAMIKA CONSTRUCTION (BID ID -3318800)

chandra builders (BID ID -3316744)