Loading…
Loading…
Eligibility, documents, scope, Go/No-Go checksEligibility, required documents, scope of work and Go/No-Go checks for this tender, in one click.
Tender Value
₹66.2 L
EMD Value
₹1.3 L
Closing Date
6 Nov 2026, 3:00 pm
Eligibility, documents, scope, Go/No-Go checksEligibility, required documents, scope of work and Go/No-Go checks for this tender, in one click.
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
ELECTRICAL
14 conditions · 3 needing a document upload
The tenderer must have minimum average annual contractual turn over of turnover of V/N or "V" whichever less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual tum over shall be calculated as an average of 'total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information asper Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet
The tenderer must have successfully completed or substantially completed any one of thefollowing categories of work(s) during last 07(seven) years, ending last day of monthprevious to the one in which tender is invited:(i) Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii) One similar costing not less than the amount equal to 60% of advertised value of the tender
Similar nature of work means works involving wiring/lighting with 240 V,1 phase or 415V, 3 phase system with control gear and protection arrangements in residential buildings or service buildings or railway stations/yards or colony/highway lightings.
46 conditions · 10 needing a document upload
PAYMENT OF BID SECURITY (EMD) : The Bid Security shall be deposited either in cash through e-payment gateway or submitted as Bank Guarantee bond (BG) from a scheduled commercial bank of India or as mentioned in tender document. The BG shall be valid for a period of 90 days beyond the bid validity period. The BG for the value of Bid Security mentioned in tender document, shall be drawn in favour of "Senior Divisional Finance Manager, DRM office, Southern Railway, Tiruchchirappalli", on account of the contractor and the original Bank Guarantee should be delivered in person to "The Senior Divisional Electrical Engineer (Traction Distribution branch), DRM office, Southern Railway, Tiruchchirappalli", before closing date for submission of bids, excluding the last date of submission of bids. Scanned copy of Bank Guarantee submitted for Bid Security shall be uploaded. It is mandatory to upload the copy of BG if it is chosen to submit the Bid Security in the form of Bank Guarantee. Non submission of scanned copy of Bank Guarantee with the bid on e-tendering portal (IREPS) and/or non- Submission of original Bank Guarantee within the specified period shall lead to summary rejection of bid.
PAN COPY : Copy of PAN Card shall be uploaded.
GST REGISTRATION CERTIFICATE: Copy of GST Registration Certificate shall be uploaded.
NEFT MANDATE :Bank official certified, filled-in copy of 'Electronic Fund Transfer Mandate form' (NEFT Form) containing tenderer's bank account details such as Name of the Bank, Bank Branch Code, Account Number, IFSC Code, etc., shall be uploaded.
RATES ARE ALL INCLUSIVE : All rates quoted by the tenderer for this work tenders shall be deemed to be inclusive of all taxes, duties, royalties, octroi, cess etc. payable by the contractor to the Govt. or any public body and no additional amount / rate or claim will be entertained on this account by the Railways. Also no claim whatsoever will be accepted by Railways on account of revision of tax rates, new taxes of statutory nature by State/Central Govt, unless otherwise any specific instruction from the statutory authorities as per extant rules.
ASSOCIATION WITH RETIRED RAILWAY EMPLOYEE : The Contractor shall abide by the instructions contained in the Clause No.16 of Annexure I of Part I and Clause No. 59(9) of Part II of Indian Railways Standard General Conditions of Contract, April 2022. In this connection, the contractor shall clearly furnish the details of employment / partnership, etc., of retired Railway employees, if any. In case of no retired railway employee associated with the firm, a statement as per the sample format at instruction to tenderer and failing which the offer will be summarily rejected.
CONSTITUTION OF THE TENDERER'S FIRM : The tenderer shall clearly specify whether the tender is submitted on his own (proprietary firm) or on behalf of a partnership Firm / Company / Joint Venture(JV) / Registered Society / Registered Trust / HUF / LLP etc. Based on their constitution of the firm, they must submit the mandatory documents mentioned hereunder, as applicable and if same is not submitted the offer will be summarily rejected. The tenderer(s) shall enclose the attested copies of constitution of their concern, and copy of PAN card along with their tender. Tender Documents in such cases are to be signed by such persons as may be legally competent to sign them on behalf of the Firm, Company, Association, Trust or Society, as the case may be.
a)If the tenderer is a Sole Proprietorship Firm, they shall submit the notarized copy of an affidavit in this regard along with copy of their Pan card and failing which the offer will be summarily rejected.
b)If the tenderer is a Hindu Undivided Family (HUF), they shall submit a copy of notarized affidavit on Stamp Paper declaring that he who is submitting the tender on behalf of HUF is in the position of 'Karta' of Hindu Undivided Family (HUF) and he has the authority, power and consent given by other members to act on behalf of HUF.
c)If the tenderer is a Partnership Firm, they shall submit (i) a notarized copy of the Partnership Deed or a copy of the Partnership deed registered with the Registrar, (ii) a notarized or registered copy of Power of Attorney in favour of the individual to tender for the work, sign the agreement etc. and create liability against the firm, (iii) an undertaking by all partners of the partnership firm that they are not blacklisted or debarred by Railways or any other Ministry / Department of the Govt, of India from participation in tenders / contracts as on the date of submission of bids, either in their individual capacity or in any firm / LLP in which they were / are partners / members. Any Concealment / wrong information in regard to above shall make the bid ineligible or the contract shall be determined under Clause 62 of the Standard General Conditions of Contract and failing which the offer will be summarily rejected.
d) If the tenderer is a Joint Venture (JV) - (If Applicable), they shall submit all the relevant documents as mentioned in para 17 of the Tender Form (Second Sheet) of GCC. (A tender from JV shall be considered only where permissible as per the tender conditions)
e) If the tenderer is a Company registered under Companies Act 2013, they shall submit (i) the copies of MOA (Memorandum of Association) and AOA (Articles of Association) of the company, (ii) a copy of Certificate of Incorporation and (iii) a copy of power of attorney duly stamped and authenticated by a Notary Public or by Magistrate (backed by the resolution of Board of Directors) in favour of the individual to sign the tender on behalf of the company and create liability against the company and failing which the offer will be summarily rejected.
f)If the tenderer is a LLP (Limited Liability Partnership), they shall submit (i) a copy of LLP Agreement, (ii) a copy of Certificate of Incorporation, (iii) a copy of Power of Attorney / Authorization issued by the LLP in favour of the individual to sign the tender on behalf of the LLP and create liability against the LLP, (iv) an undertaking by all partners of the LLP that they are not blacklisted or debarred by Railways or any other Ministry / Department of the Government of India from participation in tenders / contracts as on the date of submission of bids, either in their individual capacity or in any firm / LLP or JV in which they were / are partners/members. Concealment / wrong information in regard to above shall make the contract liable for determination under Clause 62 of the Standard General Conditions of Contract and (v) all other relevant documents in terms of Para 10 of the Tender Form (Second Sheet) of GCC.
g)If the tenderer is a Registered Society & Registered Trust, they shall submit (i) a copy of Certificate of Registration, (ii) a copy of Memorandum of Association of Society/Trust Deed, (iii) a copy of Power of Attorney in favour of the individual to sign the tender documents and create liability against the Society/Trust, (iv) a copy of Rules & Regulations of the Society and (v) all other relevant documents in terms of Para 10 of the Tender Form (Second Sheet) of GCC.
POWER OF ATTORNEY : The tenderer whether sole proprietor / a company or a partnership firm / joint venture (JV) / registered society / registered trust / HUF / LLP etc if they want to act through agent or individual partner(s), should submit along with the tender, a copy of power of attorney duly stamped and authenticated by a Notary Public or by Magistrate in favour of the specific person whether he/they be partner(s) of the firm or any other person, specifically authorizing him/them to sign the tender, submit the tender and further to deal with the Tender/ Contract up to the stage of signing the agreement except in case where such specific person is authorized for above purposes through a provision made in the partnership deed / Memorandum of Understanding / Article of Association/Board resolution, failing which offer shall be summarily rejected.
INSTRUCTIONS REGARDING LC - PART 1 :(i)For all the tenders having advertised cost of Rs. 10 lakh or above, the contractor shall have the option to take payment from Railways through a letter of credit (LC) arrangement. (ii)This option of taking payment through LC arrangement has to be exercised in IREPS (Indian Railway Electronic Procurement System - the e-application on which tenders are called by Railways) by the tenderer at the time of bidding itself, and the tenderer shall affirm having read over and agreed to the terms and conditions of the LC option. (iii)The option so exercised, shall be an integral part of the bidder's offer. (iv)The above option of taking payment through LC arrangement, once exercised by tenderer at the time of bidding, shall be final and no change shall be permitted, thereafter, during execution of contract. (v)In case tenderer opts for payment through LC, following shall be the procedure to deal release of payment through LC: (a)The LC shall be a sight LC. (b)The contractor shall select his Advising/Negotiating bank for LC. The incidental cost towards issue of LC and its operation thereof shall be borne by the contractor. (c)SBI, New Delhi, Main Branch will be the nodal branch for issue of LCs based on onlinerequests received from Railway Accounts Units for tenders opened in financial year 2018-19. SBI branches where the respective Railway Accounts Office has its Account (local SBI branch) will be the issuance/reimbursing branch for LC issued under this arrangement. The Bank shall remain same for this tender till completion of contract. The incidental cost @ 0.15 % per annum of LC value, towards issue of LC and operation thereof shall be borne by the contractor and shall be recovered from his bills. (d)The LC shall be opened initially for duration of 180 to 365 days in consultation with contractor. The LC shall be extended time to time as per the progress of the contract, on the request of the contractor. The value of LC to be opened initially as well as extended thereafter shall be finalised by the engineer in consultation with the contractor on the basis of expected progress of work. (e)The LC terms and conditions shall inter-alia indemnify and save harmless the Railway from and against all losses, claims and demands of every nature and description brought or recovered against the Railways by reason of any act or omission of the contractor, his agents or employees, in relation to the Letter of Credit (LC). All sums payable/borne by Railways on this account shall be considered as reasonable compensation and paid by contractor.
INSTRUCTIONS REGARDING LC - PART 2 : (f)The LC terms and conditions shall inter-alia provide that Railways will issue a Document of Authorisation after passing the bill for completed work, to enable contractor to claim the authorized amount from their bank. (g)The acceptable, agreed upon document for payments to be released under the LC shall be the Document of Authorisation. (h)The Document of Authorisation shall be issued by Railway Accounts Office against each bill passed by Railways. (i)On issuance of Document of Authorisation, a copy of Document of Authorisation shall be posted on IREPS for download by the contractor. A digitally signed copy of Document of Authorisation shall also be sent by Railway Accounts Office to Railway's bank (Local SBI Branch). (j)The contractor shall take print out of the Document of Authorisation available on IREPS and present his claim to his bank (advising Bank) for necessary payments as per LC terms and conditions. The claim shall comprise of copy of Document of Authorisation, Bill of Exchange and Bill. (k)The payment against LC shall be subject to verification from Railway's Bank (Local SBI Branch). (l)The contractor's bank (advising bank) shall submit the documents to the Railways Bank (Local SBI Branch0. (m)The Railway's bank (issuing bank) shall, after verifying the claim so received w.r.t. the digitally signed Document of Authorisation received from Railway Accounts Office, release the payment to contractor's bank (advising bank) for crediting the same to contractor's account. (n)Any number of bills can be dealt within one LC, provided the sum total of payments to contractor is within the amount for which LC has been opened. (o)The LC shall shall be closed after the release of final payment including PVC amount, if any, to the contractor. (p)The release of performance guarantee or security deposit shall be dealt directly by Railway with the contractor i.e., not through LC.
PAYMENT OF TENDER DOCUMENT COST : The tenderer shall deposit the Tender Document Cost (If applicable) as stipulated in the tender document, ONLY through online modes as permitted in IREPS application.
MUTUALLY BINDING : If the tenderer's offer is accepted, until the formal agreement is executed, acceptance of this tender shall constitute a binding contract between Railways and the tenderer / contractor, subject to modifications, as may be mutually agreed to between Railways and the tenderer / contractor and it will be indicated in the letter of acceptance of the tenderer / contractor's offer for this work.
ABIDANCE WITH GCC & ALL CONDITIONS : I / We also hereby agree to abide by the Indian Railways Standard General Conditions Of Contract, with all correction slips up-to-date and to carry out the work according to the Special Conditions of Contract and Specifications of materials and works as laid down by Railway in the annexed Special Conditions of contract , General Instructions and conditions, explanatory notes for schedule of work and all the Annexures.
OFFER VALIDITY : I/We agree to keep this offer open for acceptance, during offer validity period as mentioned in the tender document, from the date of tender opening and in default thereof I/We will be liable for forfeiture of my/our Earnest Money. I/We offer to do the work for Railway, at the rates quoted in the attached Schedule and hereby bind myself/ourselves to complete the works in all respects.
RIGHTS OF RAILWAYS TO INCLUDE CONDITIONS :Railways shall have the right to incorporate any such condition quoted by tenderer, in the contract, at Railway's discretion, if contract is placed on the tenderer.
TENDERER TO READ ALL CONDITIONS : I/We have read the various conditions attached/ referred to in this tender document, and agree to abide by the said conditions.
I/We hereby Confirm that the rates, rebates and/or other financial terms, if any, quoted by us in the relevant fields of the Financial Bid page will only be the ruling terms for deciding the inter-se ranking, and any such condition having financial repercussions, if quoted by us anywhere else including attached documents shall not be considered for deciding inter-se ranking
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Before quoting the rates for schedule items, the Schedule shall be read in conjunction with its explanatory notes for detailed description of various items included therein.
Indian Railways Standard General Conditions of Contract, GCC, April 2022, including all it's correction slips, upto date is applicable for this contract.
Provision of the GST Act is effective across the country from 1st July, 2017. Hence, this contract would be subjected to GST Act & Rules as applicable from time to time.
I f the Tenderer (s) deliberately give(s) w r o n g information/incorrect documents in his/their t e n d e r o r c r e a t e circumstances f o r the acceptance of his/their tender , the Railway reserves the right to reject such tender at any stage. The entire EMD and any other dues available with Railway against that contract will be forfeited. Action will be taken to suspend the business with the tenderer for a period of one year . In addition, Administration reserves t h e right to prosecute the tenderer under suitable law.
All terms and conditions in the tender documents are binding on the Tenderers.
Railways reserves the right t o accept o r reject any or all the tenders and to award the work in whole or in part without assigning the reason for any such action.
The Tenderers are advised to visit the site of work in their own interest and acquaint themselves w i t h the site conditions and expected quantum o f work and assess all the site specific difficulties to be experienced while executing the same and the rate shall be arrived duly considering all the facts above and quoted in the tender. Any representation at a later date specifying the site difficulties shall not be considered.
The tenderer shall go through the entire tender documents thoroughly and strictly adhere the instructions and directions given at different pages.
Tender Document Cost once paid is non-refundable.
Unreleased EMD of any tenderers, i f a n y , h e l d w i t h t h e Railway Administration, shall not be adjusted towards the EMD to be remitted.
Contractors are allowed TO make payments against this tender towards tender document cost (if applicable) ONLY through ONLINE payment modes available in IREPS portal, LIKE net banking, debit card, credit card etc. MANUAL payments through Demand draft, Banker cheque, Deposit receipts, FDR etc. are NOT allowed.
Tiruchchirappalli Division - Provision of improved lighting arrangements at Coach Care Complex at TPJ and Villupuram - Electrical Arrangements - Works Contract.
TPJ-E-28-2026-2027~SR
TPJ-E-28-2026-2027
Open
Works - General
90 Days
Chennai, Tamil Nadu
₹0
₹1.3 L
12 Oct 2026
12 Oct 2026
23 Oct 2026
55 items across 1 schedule
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | 66,15,978 | ||
| Excavation of cable / pipe trench and pits of required width, length in mixed soils conditions removing obstruction if any including tools & plants, labour etc., and as per instruction of site Engineer in charge and as per drawing No: DRM/EL/TPJ/40-2016. | — | — | — | 2,19,000 | |
| Excavation of cable / pipe trench and pits of required width, length and depth etc in mixed soils conditions, removing obstruction if any including tools & plants, labour etc., and as per instruction of site Engineer in charge and as per drawing No: DRM/EL/TPJ/40-2016. This item to be used for track crossing. | — | — | — | 44,000 | |
| Provision of horizontal boring underneath railway track to suit insertion of heavy duty GI pipe of 150 mm nominal dia as per the instructions of engineer incharge. | — | — | — | 3,55,000 | |
| Dismantling of tar road including necessary tools & plant labour etc., and as per instruction of site Engineer in charge | — | — | — | 2,020 | |
| Demolishing plain cement concrete including disposal of material within 50m lead .Mix leaner than 1:2:4 with coarse aggregate and tools & plant labour etc., and as per instruction of site Engineer in charge. | — | — | — | 5,720 | |
| Providing and laying of Plain Cement Concrete by mixing of 1:3:6 including supply of cement, sand etc and tools & plant labour etc., and as per instruction of site Engineer in charge for plinth and as required at site. | — | — | — | 65,250 | |
| Supply and Laying of one layer of country bricks (breadth wise) closely. | — | — | — | 4,000 | |
| Refilling of cable trench and pit by excavated soil. | — | — | — | 22,500 | |
| Laying and testing of LTUG power cable of up to and including 50 sqmm size complete with required tools & accessories. note: LTUG power cable of required size will be supplied by Railway. | — | — | — | 48,000 | |
| Laying and testing of LTUG Power cable above 50sqmm up to and including 185 sq.mm size complete with accessories. note: LTUG cable of suitable size only will be supplied by Railways. | — | — | — | 43,000 | |
| Laying of HDPE pipe of up to and including 63mm dia including supplying and fixing of necessary accessories such as straight through coupler etc. note: HDPE pipe of suitable size only will be supplied by Railway. | — | — | — | 66,600 | |
| Laying of 75 mm dia HDPE pipe including supplying and fixing of necessary accessories such as straight through coupler etc. note: HDPE pipe of suitable size only will be supplied by Railways. | — | — | — | 36,000 | |
| Supply of single compression flange type brass cable gland with aluminium crimping sockets and termination including connection of LTUG cable for sizes up to and including 50 sqmm . Note: One termination comprises of one number of single flange type brass cable gland and with four numbers of aluminium crimping sockets for all cores of the cable. | — | — | — | 23,640 | |
| Supply of single compression flange type brass cable gland with aluminium crimping sockets and termination including connection of LTUG cable for sizes above 50sqmm up to and including 185 sqmm . Note: One termination comprises of one number of single flange type brass cable gland and with four numbers of aluminium crimping sockets for all cores of the cable. | — | — | — | 42,050 | |
| Fabrication, supply and fixing of clamps made out of GI flats for fabrication of clamp for fixing of cover for existing power cable / enclosures made out of sheet metal given in this schedule etc. This shall be made out of GI flat of suitable size, powder coated of suitable colour as instructed by the engineer in charge and using GI bolts with nuts of suitable size for fixing. Note: This shall be made use for fixing of cover for existing power cable and new enclosures other than enclosures already covered in the schedule. | — | — | — | 40,800 | |
| Fabrication, supply and fixing of covers for various requirements made out of MS sheet steel of 16 SWG thick, powder coated of suitable colour as instructed by the Engineer in charge. This also includes supply and fixing of all required accessories required for the purpose for which the enclosure is proposed to be used. When used for making of enclosures, all accessories including rubber gaskets, hinges, handles locking arrangements shall also be supplied. Note: This is to be made use for fabrication of metering bunks, enclosures for various uses including cover for termination in MCB type distribution boards and switch etc and cable tray etc , which are not covered specifically in this work. | — | — | — | 62,920 | |
| Supply, placing of cast iron cable route indicators, cast iron plate type including MS flat size 40mm x6mm x 350mm length concreting and coping, painting etc complete with all other accessories as per drawing No: CEE/CN/MS/11-2004. | — | — | — | 21,640 | |
| Supply and fixing of medium duty GI pipe of 50 mm dia, conforming to IS.1239,part 1 (2004) , for cable leading without clamp. | — | — | — | 30,348 | |
| Supply and fixing of medium duty GI pipe of 65 mm dia, conforming to IS.1239, part 1 (2004), for cable leading without clamps. | — | — | — | 37,584 | |
| Supply and provision of sealing compound for cable leading pipe for leading of power cables of upto and including 50 sqmm size. | — | — | — | 5,520 | |
| Supply and provision of sealing compound for cable leading pipe for leading of cable of size above 50sqmm up to and including 185 sqmm. | — | — | — | 2,360 | |
| Erection of cut rail post up to and including 5.5 feet height with foundation and accessories like base plate, including supply of two coats of each Zinc chromate primer, aluminium paint as per drawing no CEE/CN/MS/20-2004. Note : Cut rail only will be supplied by Railways. | — | — | — | 41,120 | |
| Excavation, construction of earth pit, and provision of earth pipe complete with heavy duty GI pipe 50 mm dia with ISI mark complete with all other accessories as per Drawing. No EL / P / Type 1022. | — | — | — | 1,49,310 | |
| Supply and laying of 6 SWG GI wire, for earth continuity confirming to IS 12776 latest. | — | — | — | 21,500 | |
| Supply, laying and connection of 40 X 6 mm GI flat to earth electrode from electrical installations as per standard including minor fabrication works required. | — | — | — | 1,80,000 | |
| Supply and fixing of heavy duty GI pipe of 150 mm dia, conforming to IS.1239,part 1 (2004) , for cable leading in track crossing portion. | — | — | — | 1,45,350 | |
| Supply, erection, testing and commissioning of Medium Tension Main Distribution Board consisting of 1 no 400A TPN MCCB as incomer, 3 nos 250A TPN MCCB and 7 nos 125A TPN MCCB as outgoing, as per setailed specification and as per Drawing no DRM/EL/TPJ/12-2025.This item required RITES inspected test certificate and necessary charges for inspection to be borne by the contractor. | — | — | — | 6,31,999 | |
| Supply and fixing of Non metallic fibre glass reinforced polyester enclosure with suitable busbar arrangements with an Ingress protection of IP66 and Impact strength IK10, as per enclosed detailed specification. | — | — | — | 6,89,660 | |
| Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. | — | — | — | 35,513 | |
| Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. | — | — | — | 3,279 | |
| Extra for cutting reinforcement bars manually/ by mechanical means in R.C.C. or R.B. work (Payment shall be made on the cross sectional area of R.C.C. or R.B. work) as per direction of Engineer-in- charge. | — | — | — | 543 | |
| Supply and erection of 1 No of 125A, Four pole MCCB with 36KA breaking capacity, confirming to IS/IEC 60947-2 with sheet steel enclosure. | — | — | — | 46,305 | |
| Supply and erection of 1 No of 63A, Four pole MCCB with 36KA breaking capacity, confirming to IS/IEC 60947-2 with sheet steel enclosure. | — | — | — | 37,104 | |
| Supply and provision of 25 mm OD, rigid, heavy duty, PVC wiring conduit with ISI mark, 2 mm thick, conforming to IS.9537 part 1 and 3, suitable for electric wiring by surface with necessary accessories such as PVC junction boxes of required ways, bends, coupling, elbows, Tees, couplings etc ceiling / beam and wall opened for PVC pipes, as per specification. | — | — | — | 2,02,500 | |
| Supply and wiring of extension mains through PVC pipes already fixed / embedded by three runs of single core FRLS PVC insulated 1100V Grade ISI marked flexible multi stranded copper wiring cable including green colour wire for earth of 4.0 sqmm size, conforming to IS.694, 2010 as per specification. Note : 3 runs of 4.0sqmm copper cable added together shall be taken as 1m for measurement purpose. | — | — | — | 4,70,000 | |
| Design, manufacturing, supply at site and erection of 20mtr high mast with suitable foundation as per the specification. Note: This item requires RITES inspection and necessary charges for the inspection to be borne by the contractor. | — | — | — | 14,91,525 | |
| Supply and provision of protection/fencing arrangement for High Mast by cut rails and M.S Flat of size 40mm x 12mm for One meter height (from ground level) around 1.5 m dia. ( 8 Nos. of cut rails to be erected with mass concrete by about half a meter depth below ground level). Around the cut rail 4 layers of 40mm x 12 mm size MS flat to be welded. In between the rails MS flat- 40mm x 12mm has to be welded vertically for one meter height. Door with locking arrangements with hinges to be provided. The work includes provision of mass concrete, coping muffing, cement plastering etc. Note: - Cut Rails only will be supplied by Railways | — | — | — | 59,850 | |
| Supply and provision of suitable foundation for the octagonal poles including excavation of pit, shuttering and erection of octagonal pole as per drawing No: DRM/EL/TPJ/37-2018. | — | — | — | 85,375 | |
| Supply and fixing of 16 amps Bakelite fuse unit, 2 Amps MCB B series 10KA capacity, 20 amps SMC connector on 5mm thick SMC sheet inside the Octagonal Poles. The price offered shall be inclusive of the cost of supply and fixing of 16A fuse unit , 2A MCB B series, 20A SMC connector in 5mm thick SMC sheet inside octagonal pole. The cost offered shall be inclusive of the cost of labour charges for terminating the incoming cable in the octagonal pole. The MCB and other accessories shall be confirming to relevant IS specifications. The cable shall be terminated with suitable cable lugs to avoid loose connection in future. | — | — | — | 19,300 | |
| Wiring of light points through octagonal pole with 3 core 1.5 sq.mm wire. The price offered shall be inclusive of the cost of 1.5 sq mm wire PVC insulated copper cable three numbers one for phase, one for neutral and one for earth or 3 core 1.5 sq mm PVC insulated copper cable confirming to IS 694 : 2010 for extending the power supply from the terminal box to the lamps erected on the pole. No intermediate joints will be permitted in copper cable. The price offered shall be inclusive of the cost of labour charges required for wiring the lamp post. If the pole is fitted with double arm arrangement for providing two light fittings, Two sets of cable shall be provided. Measurement will be taken as two for double arm lamp post whereas measurement for this item will be counted as one when pole is equipped with single light fitting. | — | — | — | 21,050 | |
| Supply and fixing of medium duty GI pipe of 50 mm dia, 6meter length conforming to IS.1239, part 1 (2004), for cable leading without clamps. This includes fabrication of base plates and accessories required for provision of street light fitting. | — | — | — | 2,85,600 | |
| Supply and fixing of cable looping box made out of poly carbonate enclosure, as per cat. ref. Mi 0201 (EnyMOD model) of M/s. HENSEL make (with T locking), conforming to IP.65,for looping in and looping out of XLPE LTUG cables, with connector DP-63Amps and C series MCB 1 no SP - 2A, 10KA capacity. | — | — | — | 2,82,200 | |
| Supply and wring to luminaires with 3 Core 0.5 sqmm, PVC insulated and sheathed flexible copper cable, 1100 V grade, conforming to IS.694 2010. | — | — | — | 17,600 | |
| Fixing and testing of street light / flood light luminaires with required accessories such as GI bolts with nuts, clamps, arm brackets etc as per the instructions of Engineer-in-Charge. nb: Street light type / flood light type LED luminaire only will be supplied by Railway. | — | — | — | 1,44,619 | |
| Supply and fixing of Astronomical timer in the weather proof enclosure already provided including internal wiring, as per the instructions of Engineer incharge. This shall be equivalent to Lauritz Knudsen GIC model Astro Mini T2DDT7 or similar. | — | — | — | 31,692 | |
| Supply and fixing of 3 Pole 25A contactor switch in the weather proof enclosure already provided including internal wiring, as per the instructions of Engineer incharge. This shall be equivalent to L&T MNX 25 or similar. | — | — | — | 11,814 | |
| Supply and fixing of Residual Current Circuit Breaker 25Amps, 30ma capacity including internal wiring. | — | — | — | 19,098 | |
| Supply, installation, testing, and commissioning (SITC) of surface or flush-mounted industrial-grade Plug and Socket Distribution Boards (DB), comprising a heavy-duty Cold Rolled Close Annealed (CRCA) sheet steel enclosure treated with anti-corrosive powder coating. The unit shall feature a 2-Module configuration layout with an integrated DIN rail to house a Double Pole (DP) protective device , a clear protective window flap offering an IK08 impact rating, and an IP20 finger-proof safety design. The assembly must come pre-fitted with a 32A, 2P+E (Double Pole + Earth) industrial socket outlet and matching plug top, rated for 240V AC, 50Hz operations. The scope of work comprehensively covers all structural wall chasing, drilling, supply of anchor fasteners, internal termination using copper lugs, dress- wiring, earthing continuity connections to the primary ground network and initial commissioning test runs to the satisfaction of the Engineer-in-Charge. The product shall be similar to Legrand (Cat No. 507863 / Ekinox³ P17 Tempra Pro series) or a pre-approved equivalent matching exact performance and structural specifications. | — | — | — | 70,470 | |
| Removal of existing cable and relaying of LTUG cable of size up to 50sqmm size | — | — | — | 11,700 | |
| Removal of existing cable and relaying of LTUG cable of size above 50sqmm up to and including 185sqmm size | — | — | — | 17,400 | |
| Supply and fixing of heat shrinkable straight through join kit 4C x 50 to 95 sq.mm | — | — | — | 35,000 | |
| Supply and fixing of heat shrinkable straight through joint kit 4C x 120 to 185 sq.mm. | — | — | — | 50,000 | |
| Removal and handing over of existing Battery charger as per the instructions of site engineer incharge. | — | — | — | 5,080 | |
| Removal and handing over of portal booms as per the instructions of site engineer incharge. | — | — | — | 1,24,470 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
GCC_Works_April_2022_with_ACS_1_to_ACS_11.pdf
ATTACHMENT
BankNEFTform.pdf
ATTACHMENT
SpecificationImprovementtopitlinearrangements.pdf
ATTACHMENT
GCCannexureVIB.pdf
ATTACHMENT
ANNEXUREA14.pdf
ATTACHMENT
ANNEXURED14.pdf
ATTACHMENT
PGformat5.pdf
ATTACHMENT
GCCACS11-compressed.pdf
ATTACHMENT
INSTRUCTIONSTOTENDERERSPITLINELIGHTING.pdf
ATTACHMENT
ListofdrawingsforImprovementtopitlinearrangements.pdf List of drawings
ATTACHMENT
ListofdrawingsforImprovementtopitlinearrangements.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .