ELECTRICAL WORKS

Amount

fo|qr uxjh; forj.k e.My&f}rh;] xkft;kckn ds vUrxZr fo|qr uxjh; forj.k [k.M&"k"Ve] xkft;kckn ds dk;Z{ks= esa fctusl Iyku o"kZ 2023&24 ;kstuk esa u;s ifjorZd LFkkfir djuk] ifjorZdksa dh {kerko`f)] dsfedy vfFkZx rFkk ttZj dscy cnyuk vkfn dk dk;Z ckg~; ,tsUlh ds ek/;e ls djk;s tkus gsrqA Qty. of individual item variation ± 10%.

Construction of plinth of size 2MX2MX1.5M above ground level and one ft. below the ground level of 9”. After excavation of 4” earth, brick ballast shall be provided and rammering will be done properly after that a retaining wall of 9” width by first class brick in ratio 1:4 of cement and sand shall be made. The earth shall be filled upto one ft. below the top of the plinth. After this brick ballast shall be provided upto 6” from the earth level and froper rammering shall be done. One no. jaal of 12mm MS Tor shall be fixed in the hollow of the plinth and one ft. thick RCC in 1:2:4 ratio of cement , sand and stone ballast shall be laid on the top of the plinth. The 12mm thick plastering shall be done all around the plinth in ratio 1:4 ratio of cement and sand. The contractor shall be responsible to complete the work as per direction of supervising Engineer. It includes the cost of labour, T&P, carrier etc. required for proper completion of the work (This material will be provided by the Contactor).

Fabrication of wire mesh fencing frames of different size fabricate out of MS angle iron of size 3x3x2M. Each frame duly welded and fixing with wire mesh of size 25x25x10 SWG hot dipped galvanized within the frame pressed under MS flats of size 40x5mm inside the angle on all four side with help of approx. 20No. Bolts & Nuts of 10mm diameter 45cm legs of frame will be grouted in 1:2:4 cement coarse sand and 20mm gauge stone blast in the size of 0.22x0.22x0.45meter. Each will be painted with one coat of red oxide and two coat of Alluminium paint of approved mark after proper cleaning. Fixing of wire mess fencing around on plinth of T/F with wire gauge 25x25mm, MS Angle 35x35x5mm with gate.

Carriage of 300 Meer HT XLPE 33 KV Cable 3x300 Sq.mm, 3245 LT AB cable (3x120 + 1x95 + 1x16 Sq.mm) and 1330 Meter LT ABCE (3x95 + 1x70 + 1x16 Sq.mm) from Store Centre Shahibabad/ Ghaziabad/ JE Store to site of work including loading and unloading at both ends.

Carriage of 12 No. STP Pole of 11 Meter and 10 No. PCC Pole of 8.5 Meter from Store Centre Shahibabad/ Ghaziabad/ JE Store to site of work including loading and unloading at both ends.

Carriage of 250 KVA T/F from Store Centre Shahibabad/ Ghaziabad Store to JE Store/site of work including loading and unloading at both ends.

Carriage of 400 KVA T/F from Store Centre Shahibabad/ Ghaziabad Store to JE Store/site of work including loading and unloading at both ends.

Carriage of Line material such as 51 No. 11 KV Pin Insulator, 18 No. 11 KV Disc Insulator 45KN, 18 No. Earth Rod, 06 No. Stay Set 16x1800, 80 Meter LT PVC Aluminium Cable 1x400 Sq.mm, 40 Meter Aluminium Cable 1x240 Sq.mm, 300 KG. MS Channel 100x50x5mm, 160 KG. MS Channel of 125x65 Sq.mm, 04 No. 11 KV Dropper Channel, 04 No. 4" Chair for Rail, 02 No. Cable Box O/D 33 KV 3x300 XLPE, 110 Meter LT XLPE Cable 1x400 Sq.mm, 440 Meter ACSR Weasel Conductor, 180 Meter ACSR Dog Conductor and 04 No. A.C. 3P4W LT TVM -/5A Cat-A etc. from Store Centre Shahibabad/ Ghaziabad/ JE Store to site of work including loading and unloading at both ends.

Dismantling of OLD 100 KVA Transformer from existing site and carriage the same to JE Store/Sahibabad/Ghaziabad store including loading and unloading at both ends.

Dismantling of OLD 250 KVA Transformer from existing site and carriage the same to JE Store/Sahibabad/Ghaziabad store including loading and unloading at both ends.

Propper Installation of 250 KVA T/F on newly constructed plinth/existing plinth with the help of crane/ labour as per Respo Norms after carriage from JE Store to site of work including loading and unloading at both ends.

Propper Installation of 400 KVA T/F on newly constructed plinth/existing plinth with the help of crane/ labour as per Respo Norms after carriage from JE Store to site of work including loading and unloading at both ends.

Erection of Double Pole after digging of pits in proper size 1500x600x500mm and fixing of all material on pole & refilling by earth, complete work in all respect as per Respo norms.

Erection of PCC Pole after digging of pits in proper size ratio 1:4:8 with cement, sand and concrete as per norms of nigam. Complete work in all respect as per RESPO normes.

Laying of HT XLPE 33 KV Cable 3x300 Sq.mm and making connections of consumers by distribution box.

Laying of LT AB Cable 3x120 + 1x95 + 1x16 Sq.mm and making connections of consumers by distribution box.

Laying of LT AB Cable 3x95 + 1x70 + 1x16 Sq.mm and making connections of consumers by distribution box.

Grouting of Pole after digging of pits in proper size and grouting in ratio 1:4:8 with cement, sand and concrete as per norms of nigam. Complete work in all respect as per RESPO normes.

Earthing Complete as per RESPO Norms.

Grouting of stay set after digging of pits in proper size and grouting in ratio 1:4:8 with cement, sand and concrete as per norms of nigam. Complete work in all respect as per RESPO normes.

Work of Chemical Earthing (01 No. Body & 01 No. Neutral). All the material as per IS for Checmical Earthing will be provided by the contractor including labour.

Providing & Fixing of G.I. Barbed Wire.

Providing & Fixing of G.I. Wire 6 SWG

Providing & Fixing of G.I. Wire 4mm 8 SWG

Providing & Fixing of G.I. Pipe 6" Dia

Providing & Fixing of LT Shackle Insulator

Providing & Fixing of Crimping Type Aluminium Lug 200 Sq.mm

Providing & Fixing of Copper L-Piece for 250 Sq.mm

Providing & Fixing of LT Piercing Connector for 95/50/35

Providing & Fixing of LT Piercing Connector for 120/95

Providing & Fixing of LT Piercing Clamp for 120 Sq. mm

Providing & Fixing of Fuse Set for 11 KV

Providing & fixing of stone pad.

Providing of Red Oxide & Aluminium Paint and Painting ST Pole upto 07 Feet from ground level as per IS.

Providing & fixing of Danger Board (12x18 inch) with clamp for 11 KV.

Providing & fixing of Number Plate (6x12 inch) with clamp for 11 KV.

Providing & fixing Holding Clamp/Pole Clamp

Providing & fixing LT Clamp PCC Pole

Providing & fixing of Nuts & Bolts with washer.

Making of connection at both side of T/F with conductor & PVC Cable.

JAI MAA DURGA ELECTRICAL