Construction of Model Residential School (SH Construction of i) Academic Block ii) Principal Quarter iii) 3 Nos. Teachers Quarter iv) Administrative Staff Quarter v) Support Staff Quarter vi) Land Development at Jiribam, Imphal East District, Manipu

Amount

Construction of Administration and Academic Block

EARTH WORKS:

Earth work in excavation in foundation trenches or drains including dressing of sides and ramming of bottoms lift upto 1.5 metres including getting out the excavated soil and disposal of surplus excavated soil asdirected within a lead of 50 metres

Hard/Dense Soil

Filling available excavated earth (excluding rock) in trenches, plinth sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering lead upto 50 metres lift upto 1.5 metre

Filling in plinth with sandy soil under floors including watering ramming, consolidating and dressing complete.

CEMENT CONCRETE WORKS:

Providing and laying cement concrete in foundation and plinth excluding the cost of centering and shuttering in

1:4:8(1 Cement:4 coarse sand:8 graded stone aggregate: 40 mm nominal size)

1:5:10 ( 1 cement:4 coarse sand:8 graded stone aggregate 40mm nominal size)

Providing plinth protection 50 mm thick in cement concrete 1:3:6 (1 cement: 3 coarse sand:6 graded stone aggregate of 20 mm nominal size) i/c finishing the top surface of concrete smooth.

Providing and laying damp-proof course 50mm thick with cement concrete.

1:2:4(1 cement :2coarse sand :4graded stone aggregate 20mm nominal size).

REINFORCED CEMENT CONCRETE WORKS:

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement - All works up to plinth level:

1:1:2 (1 cement : 1 coarse sand : 2 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in wall (any thickness) including attached pilasters, buttress plinth and string course fillets, column, pillars, piers, abutments, post and sntrut etc, up to floor five level excluding cost of centering, shuttering, finishing and reinforcement:

1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in Beams, suspended floors roof having slope upto 15° landings, balconies, shelves, chajjas, bands, plain window sills stair cases and spiral staircase up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement with.

1:1.5:3 (1cement :1.5 c/sand :3 graded stone aggregate 20 mm nominal size).

Reinforcement for RCC work including straightening, cutting, bending, placing in position and binding all complete.

a)Thermo-Mechanically Treated bars

FORM WORKS:

Providing formwork i/c centering & shuttering so as to give a rough finish strutting & propping etc. height of propping and centering below supportingfloor to ceiling not exceeding 4 m. & removal for the same for in-situ reinforced and plain concrete work in : [Using 12mm shuttering ply]

Foundations, footings, bases of columns, etc. for mass concrete

Columns, pillars, posts and struts (Square, rectangular or polygonal in plan).

Sides or soffits of beams, beam haunchings, cantilevers, girders, bressumers and lintels not exceeding 1m in depth.

Flat surface such as suspended floor, roofs landings and the like

Stair cases with sloping or stepped, soffits i/c risers and stringers excluding landing

BRICK WORKS:

2nd class (local first class) brick work in foundation and plinth in cement mortar 1:3 (1 cement: 3 coarse sand)

Half brick masonry 2nd class (local 1st class) in cement mortar 1:3 (1 cement : 3 coarse sand) insuperstructure

Extra for half brick masonry in superstructure above plinth (floor one level) to floor two level.

Brick edging (brick laid on edge) in plinth protection with 2nd class brick local first class) i/c grouting with cement mortar 1:4 (1 cement: 4 fine sand).

WOOD WORKS:

Providing wood works in frames of doors, windows, clerestory windows & other frames, wrought framed & fixed in position.

Local best quality Teak Wood

P/F 38 mm. thick panelled, glazed or panelled and glazed shutters for doors, windows and clerestory windows i/c bright finished or black enamelled M.S. Iron butt hinges with necessary screws.

Local best quality Teak Wood

Providing & fixing M.S. grills of required pattern to wooden frames of window etc with M.S. flats at required spacing & frames all round bars with round headed bolts & nuts or by screws.

Ornamental grill

Providing & fixing bright finished brass 100 mm door mortice latch with one dead bolt & a pair of levers handles with necessary screws etc. complete (Indian make of approved quality).

Providing and fixing brass sliding bolts bright finished or black enamelled with nuts & screws etc.

Providing & fixing brass Tower bolts (barrel type) with screws etc. complete.

Providing & fixing brass handles with necessary screws etc. complete.

Providing & fixing M.S hooks & eyes.

Providing & fixing Aluminium haning floor door stopper,ISI marked, anodised (anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour and shade, with necessary screws etc.complete.

Single rubber syopper

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes,channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required ) and fitting the same with necessary stainless steel

Steel work in single section,i/c cutting,hoisting,fixing in position & applying a priming coat of red lead paint.

In M.S. Flate/Plate

FLOORING

20 mm thick cement plaster skirting (upto 30cm height) with cement mortar 1:3 (1 cement:3 coarse sand) finished with a floating coat of neat cement i/c. rounding of junctions with floors.

White glazed tiles 7.3 mm in flooring, treads or steps & landing laid on a bed of 12 mm thick cement mortar 1:3 (1 cement :3 coarse sand ) finished with flush pointing in white cement

White glazed tiles 10 mm thick in skirting risers of steps & dado on 10 mm thick cement plaster 1:3(1 cement:3 coarse sand) & jointed with white cement slurry.

20x30 cm size

Marble stone slab flooring over 20 mm (average) thick base of cement mortar 1 : 6 (1 cement: 6 coarse sand) laid and jointed with grey cement slurry including rubbing and polishing complete with

10 mm thick marble tiles in risers of steps , skirting , dado walls and pillars laid on 10 mm thick base of cement mortar 1 : 3 ( 1 cement: 3 coarse sand ) laid and jointed with grey cement slurry including rubbing and polishing complete

White

Extra for nosing in marble stone for treads

Providing and fixing ceiling at all heights including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanised with zinc coating of 120 gms/sqm (both side inclusive) as per IS: 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm flanges od 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs 230 mm interval, including fixing of gypsum board to

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095 - Part 1

Trapzodial Profile Pre-painted profile sheet roofing of approved brand DYNA Roof or equivalent with selt drilling screws of 68mm long Xylon coated screws with PVC washer & cap complete, excluding the coat of purlinsr & trusses.

Pre-painted Galvalume Sheet ( PPGL)

Trapixoidal Pre-painted Profile Sheet for Ridges Gutter or Valley 610 mm wide of approved brand DYNA Roof of equivalent fixed with self drilling screws of 68 mm long Xylon coated screws with PVC washer & caps completed, excluding the cost of Purlin Rafter and Trusses.

Steel work in built up tubular trusses including cutting, hoisting, fixing in position and applying a coat of approved steel primer red oxide zinc chrome primer conforming to IS:2074-1979) welded and bolted including special shape washer etc. complete.

a ) Electric resistant welded welded tube ( Conforming to IS : 1611- 1979 )

FINISHING:

12 mm cement plaster of mix :

1:3 ( 1 cement : 3 C/s )

15 mm cement plaster of mix : 1:3 (1 cement: 3c sand)

6mm cement plaster of mix : 1:3 ( 1 cement : 3 f/s )

Distempering (two or more coats) with oil bound washable distemper of approved quality on new work i/c priming coat of whiting to give an even shade.

Finishing walls with weather shield paint of approved quality on new work (three or more coats) to give even shade

Applying one coat of cement primer of approved quality on wall surface.

Applying ready mixed priming coat pink primer of approved quality on wood work.

Applying ready mixed priming coat (Red lead primer of approved quality) on steel work.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Painting (two or more coats) with synthetic enamel paint of approved quality of black or chocolate colour on wood work to give an even shade.

Painting (two or more coats) with synthetic enamel paint of approved quality all shades except black or chocolate on steel on new work to give an even shade.

EAVE BOARD

Providing and fixing 20mm plank as eave board with.

Uningthou wood.

Applying ready mixed priming coat pink primer of approved quality on wood work.

Painting (two or more coats) with synthetic enamel paint of approved quality of black or chocolate colour on wood work to give an even shade.

Providing and laying 60 mm thick factory made cement concrete interlocking paver block (Rubber Moulded) of M-30 grade made by block making machine with strong vibratory compaction and of approved size and design / shape laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with coarse sand etc. all complete as per the direction of the Engineer-incharge.

Construction of Principal Quarter

EARTH WORKS:

Earth work in excavation in foundation trenches or drains including dressing of sides and ramming of bottoms lift upto 1.5 metres including getting out the excavated soil and disposal of surplus excavated soil asdirected within a lead of 50 metres

Hard/Dense Soil

Filling available excavated earth (excluding rock) in trenches, plinth sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering lead upto 50 metres lift upto 1.5 metre

Filling in plinth with sandy soil under floors including watering ramming, consolidating and dressing complete.

CEMENT CONCRETE WORKS:

Providing and laying cement concrete in foundation and plinth excluding the cost of centering and shuttering in

1:4:8(1 Cement:4 coarse sand:8 graded stone aggregate: 40 mm nominal size)

1:5:10 ( 1 cement:4 coarse sand:8 graded stone aggregate 40mm nominal size)

Providing plinth protection 50 mm thick in cement concrete 1:3:6 (1 cement: 3 coarse sand:6 graded stone aggregate of 20 mm nominal size) i/c finishing the top surface of concrete smooth.

Providing and laying damp-proof course 50mm thick with cement concrete.

1:2:4(1 cement :2coarse sand :4graded stone aggregate 20mm nominal size).

REINFORCED CEMENT CONCRETE WORKS:

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement - All works up to plinth level:

1:1:2 (1 cement : 1 coarse sand : 2 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in wall (any thickness) including attached pilasters, buttress plinth and string course fillets, column, pillars, piers, abutments, post and sntrut etc, up to floor five level excluding cost of centering, shuttering, finishing and reinforcement:

1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in Beams, suspended floors roof having slope upto 15° landings, balconies, shelves, chajjas, bands, plain window sills stair cases and spiral staircase up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement with.

1:1.5:3 (1cement :1.5 c/sand :3 graded stone aggregate 20 mm nominal size).

Reinforcement for RCC work including straightening, cutting, bending, placing in position and binding all complete.

a)Thermo-Mechanically Treated bars

FORM WORKS:

Providing formwork i/c centering & shuttering so as to give a rough finish strutting & propping etc. height of propping and centering below supportingfloor to ceiling not exceeding 4 m. & removal for the same for in-situ reinforced and plain concrete work in : [Using 12mm shuttering ply]

Foundations, footings, bases of columns, etc. for mass concrete

Columns, pillars, posts and struts (Square, rectangular or polygonal in plan).

Sides or soffits of beams, beam haunchings, cantilevers, girders, bressumers and lintels not exceeding 1m in depth.

Flat surface such as suspended floor, roofs landings and the like

BRICK WORKS:

2nd class (local first class) brick work in foundation and plinth in cement mortar 1:3 (1 cement: 3 coarse sand)

Half brick masonry 2nd class (local 1st class) in cement mortar 1:3 (1 cement : 3 coarse sand) insuperstructure

Brick edging (brick laid on edge) in plinth protection with 2nd class brick local first class) i/c grouting with cement mortar 1:4 (1 cement: 4 fine sand).

WOOD WORKS:

Providing wood works in frames of doors, windows, clerestory windows & other frames, wrought framed & fixed in position.

a) Local best quality Teak Wood

P/F 38 mm. thick panelled, glazed or panelled and glazed shutters for doors, windows and clerestory windows i/c bright finished or black enamelled M.S. Iron butt hinges with necessary screws.

a) Local best quality Teak Wood

Providing & fixing M.S. grills of required pattern to wooden frames of window etc with M.S. flats at required spacing & frames all round bars with round headed bolts & nuts or by screws.

Ornamental grill

Providing & fixing bright finished brass 100 mm door mortice latch with one dead bolt & a pair of levers handles with necessary screws etc. complete (Indian make of approved quality).

Providing and fixing brass sliding bolts bright finished or black enamelled with nuts & screws etc.

Providing & fixing brass Tower bolts (barrel type) with screws etc. complete.

Providing & fixing brass handles with necessary screws etc. complete.

Providing & fixing M.S hooks & eyes.

Providing & fixing Aluminium haning floor door stopper,ISI marked, anodised (anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour and shade, with necessary screws etc.complete.

Single rubber syopper

STEEL WORKS

Steel work in single section,i/c cutting,hoisting,fixing in position & applying a priming coat of red lead paint.

In M.S. Flate/Plate

FLOORING

20 mm thick cement plaster skirting (upto 30cm height) with cement mortar 1:3 (1 cement:3 coarse sand) finished with a floating coat of neat cement i/c. rounding of junctions with floors.

White glazed tiles 7.3 mm in flooring, treads or steps & landing laid on a bed of 12 mm thick cement mortar 1:3 (1 cement :3 coarse sand ) finished with flush pointing in white cement

White glazed tiles 10 mm thick in skirting risers of steps & dado on 10 mm thick cement plaster 1:3(1 cement:3 coarse sand) & jointed with white cement slurry.

20x30 cm size

Marble stone slab flooring over 20 mm (average) thick base of cement mortar 1 : 6 (1 cement: 6 coarse sand) laid and jointed with grey cement slurry including rubbing and polishing complete with

10 mm thick marble tiles in risers of steps , skirting , dado walls and pillars laid on 10 mm thick base of cement mortar 1 : 3 ( 1 cement: 3 coarse sand ) laid and jointed with grey cement slurry including rubbing and polishing complete

White

Extra for nosing in marble stone for treads

Providing and fixing ceiling at all heights including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanised with zinc coating of 120 gms/sqm (both side inclusive) as per IS: 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm flanges od 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs 230 mm interval, including fixing of gypsum board to

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095 - Part 1

Trapzodial Profile Pre-painted profile sheet roofing of approved brand DYNA Roof or equivalent with selt drilling screws of 68mm long Xylon coated screws with PVC washer & cap complete, excluding the coat of purlinsr & trusses.

Pre-painted Galvalume Sheet ( PPGL)

Trapixoidal Pre-painted Profile Sheet for Ridges Gutter or Valley 610 mm wide of approved brand DYNA Roof of equivalent fixed with self drilling screws of 68 mm long Xylon coated screws with PVC washer & caps completed, excluding the cost of Purlin Rafter and Trusses.

Steel work in built up tubular trusses including cutting, hoisting, fixing in position and applying a coat of approved steel primer red oxide zinc chrome primer conforming to IS:2074-1979) welded and bolted including special shape washer etc. complete.

a ) Electric resistant welded welded tube ( Conforming to IS : 1611- 1979 )

FINISHING:

12 mm cement plaster of mix :

1:3 ( 1 cement : 3 C/s )

15 mm cement plaster of mix : 1:3 (1 cement: 3c sand)

Distempering (two or more coats) with oil bound washable distemper of approved quality on new work i/c priming coat of whiting to give an even shade.

Finishing walls with weather shield paint of approved quality on new work (three or more coats) to give even shade

Applying one coat of cement primer of approved quality on wall surface.

Applying ready mixed priming coat pink primer of approved quality on wood work.

Applying ready mixed priming coat (Red lead primer of approved quality) on steel work.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Painting (two or more coats) with synthetic enamel paint of approved quality of black or chocolate colour on wood work to give an even shade.

Painting (two or more coats) with synthetic enamel paint of approved quality all shades except black or chocolate on steel on new work to give an even shade.

EAVE BOARD

Providing and fixing 20mm plank as eave board with.

Uningthou wood.

Applying ready mixed priming coat pink primer of approved quality on wood work.

Painting (two or more coats) with synthetic enamel paint of approved quality of black or chocolate colour on wood work to give an even shade.

Construction of Teachers Quarter-I

EARTH WORKS:

Earth work in excavation in foundation trenches or drains including dressing of sides and ramming of bottoms lift upto 1.5 metres including getting out the excavated soil and disposal of surplus excavated soil asdirected within a lead of 50 metres

Hard/Dense Soil

Filling available excavated earth (excluding rock) in trenches, plinth sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering lead upto 50 metres lift upto 1.5 metre

Filling in plinth with sandy soil under floors including watering ramming, consolidating and dressing complete.

CEMENT CONCRETE WORKS:

Providing and laying cement concrete in foundation and plinth excluding the cost of centering and shuttering in

1:4:8(1 Cement:4 coarse sand:8 graded stone aggregate: 40 mm nominal size)

1:5:10 ( 1 cement:4 coarse sand:8 graded stone aggregate 40mm nominal size)

Providing plinth protection 50 mm thick in cement concrete 1:3:6 (1 cement: 3 coarse sand:6 graded stone aggregate of 20 mm nominal size) i/c finishing the top surface of concrete smooth.

Providing and laying damp-proof course 50mm thick with cement concrete.

1:2:4(1 cement :2coarse sand :4graded stone aggregate 20mm nominal size).

REINFORCED CEMENT CONCRETE WORKS:

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement - All works up to plinth level:

1:1:2 (1 cement : 1 coarse sand : 2 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in wall (any thickness) including attached pilasters, buttress plinth and string course fillets, column, pillars, piers, abutments, post and sntrut etc, up to floor five level excluding cost of centering, shuttering, finishing and reinforcement:

1:1.5:3(1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in Beams, suspended floors roof having slope upto 15° landings, balconies, shelves, chajjas, bands, plain window sills stair cases and spiral staircase up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement with.

1:1.5:3 (1cement :1.5 c/sand :3 graded stone aggregate 20 mm nominal size).

Reinforcement for RCC work including straightening, cutting, bending, placing in position and binding all complete.

a)Thermo-Mechanically Treated bars

FORM WORKS:

Providing formwork i/c centering & shuttering so as to give a rough finish strutting & propping etc. height of propping and centering below supportingfloor to ceiling not exceeding 4 m. & removal for the same for in-situ reinforced and plain concrete work in : [Using 12mm shuttering ply]

Foundations, footings, bases of columns, etc. for mass concrete

Columns, pillars, posts and struts (Square, rectangular or polygonal in plan).

Sides or soffits of beams, beam haunchings, cantilevers, girders, bressumers and lintels not exceeding 1m in depth.

Flat surface such as suspended floor, roofs landings and the like

Stair cases with sloping or stepped, soffits i/c risers and stringers excluding landing

BRICK WORKS:

2nd class (local first class) brick work in foundation and plinth in cement mortar 1:3 (1 cement: 3 coarse sand)

Half brick masonry 2nd class (local 1st class) in cement mortar 1:3 (1 cement : 3 coarse sand) insuperstructure

Extra for half brick masonry in superstructure above plinth (floor one level) to floor two level.

Brick edging (brick laid on edge) in plinth protection with 2nd class brick local first class) i/c grouting with cement mortar 1:4 (1 cement: 4 fine sand).

WOOD WORKS:

Providing wood works in frames of doors, windows, clerestory windows & other frames, wrought framed & fixed in position.

Local best quality Teak Wood

P/F 38 mm. thick panelled, glazed or panelled and glazed shutters for doors, windows and clerestory windows i/c bright finished or black enamelled M.S. Iron butt hinges with necessary screws.

Local best quality Teak Wood

Providing & fixing M.S. grills of required pattern to wooden frames of window etc with M.S. flats at required spacing & frames all round bars with round headed bolts & nuts or by screws.

Ornamental grill

Providing & fixing bright finished brass 100 mm door mortice latch with one dead bolt & a pair of levers handles with necessary screws etc. complete (Indian make of approved quality).

Providing and fixing brass sliding bolts bright finished or black enamelled with nuts & screws etc.

Providing & fixing brass Tower bolts (barrel type) with screws etc. complete.

Providing & fixing brass handles with necessary screws etc. complete.

Providing & fixing M.S hooks & eyes.

Providing & fixing Aluminium haning floor door stopper,ISI marked, anodised (anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour and shade, with necessary screws etc.complete.

Single rubber syopper

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes,channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required ) and fitting the same with necessary stainless steel

FLOORING

20 mm thick cement plaster skirting (upto 30cm height) with cement mortar 1:3 (1 cement:3 coarse sand) finished with a floating coat of neat cement i/c. rounding of junctions with floors.

White glazed tiles 7.3 mm in flooring, treads or steps & landing laid on a bed of 12 mm thick cement mortar 1:3 (1 cement :3 coarse sand ) finished with flush pointing in white cement

White glazed tiles 10 mm thick in skirting risers of steps & dado on 10 mm thick cement plaster 1:3(1 cement:3 coarse sand) & jointed with white cement slurry.

20x30 cm size

Marble stone slab flooring over 20 mm (average) thick base of cement mortar 1 : 6 (1 cement: 6 coarse sand) laid and jointed with grey cement slurry including rubbing and polishing complete with

10 mm thick marble tiles in risers of steps , skirting , dado walls and pillars laid on 10 mm thick base of cement mortar 1 : 3 ( 1 cement: 3 coarse sand ) laid and jointed with grey cement slurry including rubbing and polishing complete

White

Extra for nosing in marble stone for treads

Providing and fixing ceiling at all heights including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanised with zinc coating of 120 gms/sqm (both side inclusive) as per IS: 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm flanges od 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs 230 mm interval, including fixing of gypsum board to

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095 - Part 1

Trapzodial Profile Pre-painted profile sheet roofing of approved brand DYNA Roof or equivalent with selt drilling screws of 68mm long Xylon coated screws with PVC washer & cap complete, excluding the coat of purlinsr & trusses.

Pre-painted Galvalume Sheet ( PPGL)

Trapixoidal Pre-painted Profile Sheet for Ridges Gutter or Valley 610 mm wide of approved brand DYNA Roof of equivalent fixed with self drilling screws of 68 mm long Xylon coated screws with PVC washer & caps completed, excluding the cost of Purlin Rafter and Trusses.

Steel work in built up tubular trusses including cutting, hoisting, fixing in position and applying a coat of approved steel primer red oxide zinc chrome primer conforming to IS:2074-1979) welded and bolted including special shape washer etc. complete.

a ) Electric resistant welded welded tube ( Conforming to IS : 1611- 1979 )

FINISHING:

12 mm cement plaster of mix :

1:3 ( 1 cement : 3 C/s )

15 mm cement plaster of mix : 1:3 (1 cement: 3c sand)

6mm cement plaster of mix : 1:3 ( 1 cement : 3 f/s )

Distempering (two or more coats) with oil bound washable distemper of approved quality on new work i/c priming coat of whiting to give an even shade.

Finishing walls with weather shield paint of approved quality on new work (three or more coats) to give even shade

Applying one coat of cement primer of approved quality on wall surface.

Applying ready mixed priming coat pink primer of approved quality on wood work.

Applying ready mixed priming coat (Red lead primer of approved quality) on steel work.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Painting (two or more coats) with synthetic enamel paint of approved quality of black or chocolate colour on wood work to give an even shade.

Painting (two or more coats) with synthetic enamel paint of approved quality all shades except black or chocolate on steel on new work to give an even shade.

EAVE BOARD

Providing and fixing 20mm plank as eave board with.

Uningthou wood.

Applying ready mixed priming coat pink primer of approved quality on wood work.

Painting (two or more coats) with synthetic enamel paint of approved quality of black or chocolate colour on wood work to give an even shade.

Construction of Teachers Quarter-II

EARTH WORKS:

Earth work in excavation in foundation trenches or drains including dressing of sides and ramming of bottoms lift upto 1.5 metres including getting out the excavated soil and disposal of surplus excavated soil asdirected within a lead of 50 metres

Hard/Dense Soil

Filling available excavated earth (excluding rock) in trenches, plinth sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering lead upto 50 metres lift upto 1.5 metre

Filling in plinth with sandy soil under floors including watering ramming, consolidating and dressing complete.

CEMENT CONCRETE WORKS:

Providing and laying cement concrete in foundation and plinth excluding the cost of centering and shuttering in

1:4:8(1 Cement:4 coarse sand:8 graded stone aggregate: 40 mm nominal size)

1:5:10 ( 1 cement:4 coarse sand:8 graded stone aggregate 40mm nominal size)

Providing plinth protection 50 mm thick in cement concrete 1:3:6 (1 cement: 3 coarse sand:6 graded stone aggregate of 20 mm nominal size) i/c finishing the top surface of concrete smooth.

Providing and laying damp-proof course 50mm thick with cement concrete.

1:2:4(1 cement :2coarse sand :4graded stone aggregate 20mm nominal size).

REINFORCED CEMENT CONCRETE WORKS:

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement - All works up to plinth level:

1:1:2 (1 cement : 1 coarse sand : 2 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in wall (any thickness) including attached pilasters, buttress plinth and string course fillets, column, pillars, piers, abutments, post and sntrut etc, up to floor five level excluding cost of centering, shuttering, finishing and reinforcement:

1:1.5:3(1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in Beams, suspended floors roof having slope upto 15° landings, balconies, shelves, chajjas, bands, plain window sills stair cases and spiral staircase up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement with.

1:1.5:3 (1cement :1.5 c/sand :3 graded stone aggregate 20 mm nominal size).

Reinforcement for RCC work including straightening, cutting, bending, placing in position and binding all complete.

a)Thermo-Mechanically Treated bars

FORM WORKS:

Providing formwork i/c centering & shuttering so as to give a rough finish strutting & propping etc. height of propping and centering below supportingfloor to ceiling not exceeding 4 m. & removal for the same for in-situ reinforced and plain concrete work in : [Using 12mm shuttering ply]

Foundations, footings, bases of columns, etc. for mass concrete

Columns, pillars, posts and struts (Square, rectangular or polygonal in plan).

Sides or soffits of beams, beam haunchings, cantilevers, girders, bressumers and lintels not exceeding 1m in depth.

Flat surface such as suspended floor, roofs landings and the like

Stair cases with sloping or stepped, soffits i/c risers and stringers excluding landing

BRICK WORKS:

2nd class (local first class) brick work in foundation and plinth in cement mortar 1:3 (1 cement: 3 coarse sand)

Half brick masonry 2nd class (local 1st class) in cement mortar 1:3 (1 cement : 3 coarse sand) insuperstructure

Extra for half brick masonry in superstructure above plinth (floor one level) to floor two level.

Brick edging (brick laid on edge) in plinth protection with 2nd class brick local first class) i/c grouting with cement mortar 1:4 (1 cement: 4 fine sand).

WOOD WORKS:

Providing wood works in frames of doors, windows, clerestory windows & other frames, wrought framed & fixed in position.

Local best quality Teak Wood

P/F 38 mm. thick panelled, glazed or panelled and glazed shutters for doors, windows and clerestory windows i/c bright finished or black enamelled M.S. Iron butt hinges with necessary screws.

Local best quality Teak Wood

Providing & fixing M.S. grills of required pattern to wooden frames of window etc with M.S. flats at required spacing & frames all round bars with round headed bolts & nuts or by screws.

Ornamental grill

Providing & fixing bright finished brass 100 mm door mortice latch with one dead bolt & a pair of levers handles with necessary screws etc. complete (Indian make of approved quality).

Providing and fixing brass sliding bolts bright finished or black enamelled with nuts & screws etc.

Providing & fixing brass Tower bolts (barrel type) with screws etc. complete.

Providing & fixing brass handles with necessary screws etc. complete.

Providing & fixing M.S hooks & eyes.

Providing & fixing Aluminium haning floor door stopper,ISI marked, anodised (anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour and shade, with necessary screws etc.complete.

Single rubber syopper

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes,channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required ) and fitting the same with necessary stainless steel

FLOORING

20 mm thick cement plaster skirting (upto 30cm height) with cement mortar 1:3 (1 cement:3 coarse sand) finished with a floating coat of neat cement i/c. rounding of junctions with floors.

White glazed tiles 7.3 mm in flooring, treads or steps & landing laid on a bed of 12 mm thick cement mortar 1:3 (1 cement :3 coarse sand ) finished with flush pointing in white cement

White glazed tiles 10 mm thick in skirting risers of steps & dado on 10 mm thick cement plaster 1:3(1 cement:3 coarse sand) & jointed with white cement slurry.

20x30 cm size

Marble stone slab flooring over 20 mm (average) thick base of cement mortar 1 : 6 (1 cement: 6 coarse sand) laid and jointed with grey cement slurry including rubbing and polishing complete with

10 mm thick marble tiles in risers of steps , skirting , dado walls and pillars laid on 10 mm thick base of cement mortar 1 : 3 ( 1 cement: 3 coarse sand ) laid and jointed with grey cement slurry including rubbing and polishing complete

White

Extra for nosing in marble stone for treads

Providing and fixing ceiling at all heights including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanised with zinc coating of 120 gms/sqm (both side inclusive) as per IS: 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm flanges od 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs 230 mm interval, including fixing of gypsum board to

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095 - Part 1

Trapzodial Profile Pre-painted profile sheet roofing of approved brand DYNA Roof or equivalent with selt drilling screws of 68mm long Xylon coated screws with PVC washer & cap complete, excluding the coat of purlinsr & trusses.

Pre-painted Galvalume Sheet ( PPGL)

Trapixoidal Pre-painted Profile Sheet for Ridges Gutter or Valley 610 mm wide of approved brand DYNA Roof of equivalent fixed with self drilling screws of 68 mm long Xylon coated screws with PVC washer & caps completed, excluding the cost of Purlin Rafter and Trusses.

Steel work in built up tubular trusses including cutting, hoisting, fixing in position and applying a coat of approved steel primer red oxide zinc chrome primer conforming to IS:2074-1979) welded and bolted including special shape washer etc. complete.

a ) Electric resistant welded welded tube ( Conforming to IS : 1611- 1979 )

FINISHING:

12 mm cement plaster of mix :

1:3 ( 1 cement : 3 C/s )

15 mm cement plaster of mix : 1:3 (1 cement: 3c sand)

6mm cement plaster of mix : 1:3 ( 1 cement : 3 f/s )

Distempering (two or more coats) with oil bound washable distemper of approved quality on new work i/c priming coat of whiting to give an even shade.

Finishing walls with weather shield paint of approved quality on new work (three or more coats) to give even shade

Applying one coat of cement primer of approved quality on wall surface.

Applying ready mixed priming coat pink primer of approved quality on wood work.

Applying ready mixed priming coat (Red lead primer of approved quality) on steel work.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Painting (two or more coats) with synthetic enamel paint of approved quality of black or chocolate colour on wood work to give an even shade.

Painting (two or more coats) with synthetic enamel paint of approved quality all shades except black or chocolate on steel on new work to give an even shade.

EAVE BOARD

Providing and fixing 20mm plank as eave board with.

Uningthou wood.

Applying ready mixed priming coat pink primer of approved quality on wood work.

Painting (two or more coats) with synthetic enamel paint of approved quality of black or chocolate colour on wood work to give an even shade.

Construction of Teachers Quarter-III

EARTH WORKS:

Earth work in excavation in foundation trenches or drains including dressing of sides and ramming of bottoms lift upto 1.5 metres including getting out the excavated soil and disposal of surplus excavated soil asdirected within a lead of 50 metres

Hard/Dense Soil

Filling available excavated earth (excluding rock) in trenches, plinth sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering lead upto 50 metres lift upto 1.5 metre

Filling in plinth with sandy soil under floors including watering ramming, consolidating and dressing complete.

CEMENT CONCRETE WORKS:

Providing and laying cement concrete in foundation and plinth excluding the cost of centering and shuttering in

1:4:8(1 Cement:4 coarse sand:8 graded stone aggregate: 40 mm nominal size)

1:5:10 ( 1 cement:4 coarse sand:8 graded stone aggregate 40mm nominal size)

Providing plinth protection 50 mm thick in cement concrete 1:3:6 (1 cement: 3 coarse sand:6 graded stone aggregate of 20 mm nominal size) i/c finishing the top surface of concrete smooth.

Providing and laying damp-proof course 50mm thick with cement concrete.

1:2:4(1 cement :2coarse sand :4graded stone aggregate 20mm nominal size).

REINFORCED CEMENT CONCRETE WORKS:

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement - All works up to plinth level:

1:1:2 (1 cement : 1 coarse sand : 2 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in wall (any thickness) including attached pilasters, buttress plinth and string course fillets, column, pillars, piers, abutments, post and sntrut etc, up to floor five level excluding cost of centering, shuttering, finishing and reinforcement:

1:1.5:3(1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in Beams, suspended floors roof having slope upto 15° landings, balconies, shelves, chajjas, bands, plain window sills stair cases and spiral staircase up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement with.

1:1.5:3 (1cement :1.5 c/sand :3 graded stone aggregate 20 mm nominal size).

Reinforcement for RCC work including straightening, cutting, bending, placing in position and binding all complete.

a)Thermo-Mechanically Treated bars

FORM WORKS:

Providing formwork i/c centering & shuttering so as to give a rough finish strutting & propping etc. height of propping and centering below supportingfloor to ceiling not exceeding 4 m. & removal for the same for in-situ reinforced and plain concrete work in : [Using 12mm shuttering ply]

Foundations, footings, bases of columns, etc. for mass concrete

Columns, pillars, posts and struts (Square, rectangular or polygonal in plan).

Sides or soffits of beams, beam haunchings, cantilevers, girders, bressumers and lintels not exceeding 1m in depth.

Flat surface such as suspended floor, roofs landings and the like

Stair cases with sloping or stepped, soffits i/c risers and stringers excluding landing

BRICK WORKS:

2nd class (local first class) brick work in foundation and plinth in cement mortar 1:3 (1 cement: 3 coarse sand)

Half brick masonry 2nd class (local 1st class) in cement mortar 1:3 (1 cement : 3 coarse sand) insuperstructure

Extra for half brick masonry in superstructure above plinth (floor one level) to floor two level.

Brick edging (brick laid on edge) in plinth protection with 2nd class brick local first class) i/c grouting with cement mortar 1:4 (1 cement: 4 fine sand).

WOOD WORKS:

Providing wood works in frames of doors, windows, clerestory windows & other frames, wrought framed & fixed in position.

Local best quality Teak Wood

P/F 38 mm. thick panelled, glazed or panelled and glazed shutters for doors, windows and clerestory windows i/c bright finished or black enamelled M.S. Iron butt hinges with necessary screws.

Local best quality Teak Wood

Providing & fixing M.S. grills of required pattern to wooden frames of window etc with M.S. flats at required spacing & frames all round bars with round headed bolts & nuts or by screws.

Ornamental grill

Providing & fixing bright finished brass 100 mm door mortice latch with one dead bolt & a pair of levers handles with necessary screws etc. complete (Indian make of approved quality).

Providing and fixing brass sliding bolts bright finished or black enamelled with nuts & screws etc.

Providing & fixing brass Tower bolts (barrel type) with screws etc. complete.

Providing & fixing brass handles with necessary screws etc. complete.

Providing & fixing M.S hooks & eyes.

Providing & fixing Aluminium haning floor door stopper,ISI marked, anodised (anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour and shade, with necessary screws etc.complete.

Single rubber syopper

Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes,channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required ) and fitting the same with necessary stainless steel

FLOORING

20 mm thick cement plaster skirting (upto 30cm height) with cement mortar 1:3 (1 cement:3 coarse sand) finished with a floating coat of neat cement i/c. rounding of junctions with floors.

White glazed tiles 7.3 mm in flooring, treads or steps & landing laid on a bed of 12 mm thick cement mortar 1:3 (1 cement :3 coarse sand ) finished with flush pointing in white cement

White glazed tiles 10 mm thick in skirting risers of steps & dado on 10 mm thick cement plaster 1:3(1 cement:3 coarse sand) & jointed with white cement slurry.

20x30 cm size

Marble stone slab flooring over 20 mm (average) thick base of cement mortar 1 : 6 (1 cement: 6 coarse sand) laid and jointed with grey cement slurry including rubbing and polishing complete with

10 mm thick marble tiles in risers of steps , skirting , dado walls and pillars laid on 10 mm thick base of cement mortar 1 : 3 ( 1 cement: 3 coarse sand ) laid and jointed with grey cement slurry including rubbing and polishing complete

White

Extra for nosing in marble stone for treads

Providing and fixing ceiling at all heights including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanised with zinc coating of 120 gms/sqm (both side inclusive) as per IS: 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm flanges od 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs 230 mm interval, including fixing of gypsum board to

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095 - Part 1

Trapzodial Profile Pre-painted profile sheet roofing of approved brand DYNA Roof or equivalent with selt drilling screws of 68mm long Xylon coated screws with PVC washer & cap complete, excluding the coat of purlinsr & trusses.

Pre-painted Galvalume Sheet ( PPGL)

Trapixoidal Pre-painted Profile Sheet for Ridges Gutter or Valley 610 mm wide of approved brand DYNA Roof of equivalent fixed with self drilling screws of 68 mm long Xylon coated screws with PVC washer & caps completed, excluding the cost of Purlin Rafter and Trusses.

Steel work in built up tubular trusses including cutting, hoisting, fixing in position and applying a coat of approved steel primer red oxide zinc chrome primer conforming to IS:2074-1979) welded and bolted including special shape washer etc. complete.

a ) Electric resistant welded welded tube ( Conforming to IS : 1611- 1979 )

FINISHING:

12 mm cement plaster of mix :

1:3 ( 1 cement : 3 C/s )

15 mm cement plaster of mix : 1:3 (1 cement: 3c sand)

6mm cement plaster of mix : 1:3 ( 1 cement : 3 f/s )

Distempering (two or more coats) with oil bound washable distemper of approved quality on new work i/c priming coat of whiting to give an even shade.

Finishing walls with weather shield paint of approved quality on new work (three or more coats) to give even shade

Applying one coat of cement primer of approved quality on wall surface.

Applying ready mixed priming coat pink primer of approved quality on wood work.

Applying ready mixed priming coat (Red lead primer of approved quality) on steel work.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Painting (two or more coats) with synthetic enamel paint of approved quality of black or chocolate colour on wood work to give an even shade.

Painting (two or more coats) with synthetic enamel paint of approved quality all shades except black or chocolate on steel on new work to give an even shade.

EAVE BOARD

Providing and fixing 20mm plank as eave board with.

Uningthou wood.

Applying ready mixed priming coat pink primer of approved quality on wood work.

Painting (two or more coats) with synthetic enamel paint of approved quality of black or chocolate colour on wood work to give an even shade.

Construction Administrative Staff Quarter

EARTH WORKS:

Earth work in excavation in foundation trenches or drains including dressing of sides and ramming of bottoms lift upto 1.5 metres including getting out the excavated soil and disposal of surplus excavated soil asdirected within a lead of 50 metres

Hard/Dense Soil

Filling available excavated earth (excluding rock) in trenches, plinth sides of foundation etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering lead upto 50 metres lift upto 1.5 metre

Filling in plinth with sandy soil under floors including watering ramming, consolidating and dressing complete.

CEMENT CONCRETE WORKS:

Providing and laying cement concrete in foundation and plinth excluding the cost of centering and shuttering in

1:4:8(1 Cement:4 coarse sand:8 graded stone aggregate: 40 mm nominal size)

1:5:10 ( 1 cement:4 coarse sand:8 graded stone aggregate 40mm nominal size)

Providing plinth protection 50 mm thick in cement concrete 1:3:6 (1 cement: 3 coarse sand:6 graded stone aggregate of 20 mm nominal size) i/c finishing the top surface of concrete smooth.

Providing and laying damp-proof course 50mm thick with cement concrete.

1:2:4(1 cement :2coarse sand :4graded stone aggregate 20mm nominal size).

REINFORCED CEMENT CONCRETE WORKS:

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement - All works up to plinth level:

1:1:2 (1 cement : 1 coarse sand : 2 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in wall (any thickness) including attached pilasters, buttress plinth and string course fillets, column, pillars, piers, abutments, post and sntrut etc, up to floor five level excluding cost of centering, shuttering, finishing and reinforcement:

1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in Beams, suspended floors roof having slope upto 15° landings, balconies, shelves, chajjas, bands, plain window sills stair cases and spiral staircase up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement with.

1:1.5:3 (1cement :1.5 c/sand :3 graded stone aggregate 20 mm nominal size).

Reinforcement for RCC work including straightening, cutting, bending, placing in position and binding all complete.

a)Thermo-Mechanically Treated bars

FORM WORKS:

Providing form works i/c centering and shuttering so as to give a rough finish, strutting and propping etc.height of propping and centering below upporting floor to ceiling not exceeding 4 m and removal of the same for in-situ reinforced concrete and plain concrete work in

Foundations, footings, bases of columns, etc. for mass concrete

Columns, pillars, posts and struts (Square, rectangular or polygonal in plan).

Sides or soffits of beams, beam haunchings, cantilevers, girders, bressumers and lintels not exceeding 1m in depth.

BRICK WORKS:

2nd class (local first class) brick work in foundation and plinth in cement mortar 1:3 (1 cement: 3 coarse sand)

Half brick masonry 2nd class (local 1st class) in cement mortar 1:3 (1 cement : 3 coarse sand) insuperstructure

Brick edging (brick laid on edge) in plinth protection with 2nd class brick local first class) i/c grouting with cement mortar 1:4 (1 cement: 4 fine sand).

WOOD WORKS:

Providing wood works in frames of doors, windows, clerestory windows & other frames, wrought framed & fixed in position.

a) Local best quality Teak Wood

P/F 38 mm. thick panelled, glazed or panelled and glazed shutters for doors, windows and clerestory windows i/c bright finished or black enamelled M.S. Iron butt hinges with necessary screws.

a) Local best quality Teak Wood

Providing & fixing M.S. grills of required pattern to wooden frames of window etc with M.S. flats at required spacing & frames all round bars with round headed bolts & nuts or by screws.

Ornamental grill

Providing & fixing bright finished brass 100 mm door mortice latch with one dead bolt & a pair of levers handles with necessary screws etc. complete (Indian make of approved quality).

Providing and fixing brass sliding bolts bright finished or black enamelled with nuts & screws etc.

Providing & fixing brass Tower bolts (barrel type) with screws etc. complete.

Providing & fixing brass handles with necessary screws etc. complete.

Providing & fixing M.S hooks & eyes.

Providing & fixing Aluminium haning floor door stopper,ISI marked, anodised (anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour and shade, with necessary screws etc.complete.

Single rubber syopper

STEEL WORKS

Steel work in single section,i/c cutting,hoisting,fixing in position & applying a priming coat of red lead paint.

In M.S. Flate/Plate

FLOORING

20 mm thick cement plaster skirting (upto 30cm height) with cement mortar 1:3 (1 cement:3 coarse sand) finished with a floating coat of neat cement i/c. rounding of junctions with floors.

White glazed tiles 7.3 mm in flooring, treads or steps & landing laid on a bed of 12 mm thick cement mortar 1:3 (1 cement :3 coarse sand ) finished with flush pointing in white cement

White glazed tiles 10 mm thick in skirting risers of steps & dado on 10 mm thick cement plaster 1:3(1 cement:3 coarse sand) & jointed with white cement slurry.

20x30 cm size

Marble stone slab flooring over 20 mm (average) thick base of cement mortar 1 : 6 (1 cement: 6 coarse sand) laid and jointed with grey cement slurry including rubbing and polishing complete with

10 mm thick marble tiles in risers of steps , skirting , dado walls and pillars laid on 10 mm thick base of cement mortar 1 : 3 ( 1 cement: 3 coarse sand ) laid and jointed with grey cement slurry including rubbing and polishing complete

White

Extra for nosing in marble stone for treads

Providing and fixing ceiling at all heights including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanised with zinc coating of 120 gms/sqm (both side inclusive) as per IS: 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm flanges od 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs 230 mm interval, including fixing of gypsum board to

12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095 - Part 1

Trapzodial Profile Pre-painted profile sheet roofing of approved brand DYNA Roof or equivalent with selt drilling screws of 68mm long Xylon coated screws with PVC washer & cap complete, excluding the coat of purlinsr & trusses.

Pre-painted Galvalume Sheet ( PPGL)

Trapixoidal Pre-painted Profile Sheet for Ridges Gutter or Valley 610 mm wide of approved brand DYNA Roof of equivalent fixed with self drilling screws of 68 mm long Xylon coated screws with PVC washer & caps completed, excluding the cost of Purlin Rafter and Trusses.

Steel work in built up tubular trusses including cutting, hoisting, fixing in position and applying a coat of approved steel primer red oxide zinc chrome primer conforming to IS:2074-1979) welded and bolted including special shape washer etc. complete.

a ) Electric resistant welded welded tube ( Conforming to IS : 1611- 1979 )

FINISHING:

12 mm cement plaster of mix :

1:3 ( 1 cement : 3 C/s )

15 mm cement plaster of mix : 1:3 (1 cement: 3c sand)

Distempering (two or more coats) with oil bound washable distemper of approved quality on new work i/c priming coat of whiting to give an even shade.

Finishing walls with weather shield paint of approved quality on new work (three or more coats) to give even shade

Applying one coat of cement primer of approved quality on wall surface.

Applying ready mixed priming coat pink primer of approved quality on wood work.

Applying ready mixed priming coat (Red lead primer of approved quality) on steel work.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Painting (two or more coats) with synthetic enamel paint of approved quality of black or chocolate colour on wood work to give an even shade.

Painting (two or more coats) with synthetic enamel paint of approved quality all shades except black or chocolate on steel on new work to give an even shade.

EAVE BOARD

Providing and fixing 20mm plank as eave board with.

Uningthou wood.

Applying ready mixed priming coat pink primer of approved quality on wood work.

Painting (two or more coats) with synthetic enamel paint of approved quality of black or chocolate colour on wood work to give an even shade.

Construction of Support Staff Quarter

EARTH WORKS:

Earth work in excavation in foundation trenches or drains i/c dressing of sides & ramming of bottoms lift upto 1.5 m i/c getting out the excavated soil & disposal of surplus excavated soil as directed within a lead of 50 m.

Hard/Dense Soil.

Filling available excavated earth (excluding rock) in trenches, plinth sides of foundation etc. in layers not exceeding 20 cm in depth consolidating each deposited layer cum by ramming and watering lead upto 50 m and lift upto 1.5 m

Filling in plinth with sandy soil under floors i/c watering, ramming, consolidating & dressing complete.

Providing and laying cement concrete in foundation & plinth excluding the cost of centering & shuttering.

1:4:8 (1 Cement:4 coarse sand:8 graded stone aggregate: 40 mm nominal size)

Providing & laying damp-proof course 50 mm thick with cement concrete

cement concrete 1 : 2 : 4 (1 cement :2 coarse sand : 4 graded stone aggregate 12.5mm nominal size)

Providing plinth protection 50 mm thick in cement concrete 1:3:6 (1 cement:3 coarse sand:6 graded stone aggrt. of 20 mm nominal size) i/c finishing the top surface of concrete smooth.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work upto plinth level

1:1:2 (1 cement :1 coarse sand :2 graded stone aggregate 20 mm nominal size)

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :

1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

R.C.C. work in beams, suspended floors, roofs having slope uptp 15o landings, balconies, shelves, chajjas, lintels, band, plain window sills, staircases and spiral staircases above plinth level upto floor five level excluding the cost of centering, shuttering, finishing and reinforcement, with

1 : 1 .5: 3 (1 cement :1.5 coarse sand :3 graded stone aggregate 20 mm nominal size)

Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete.

Thermo-Mechanically Treated bars

FORMWORK

Providing formwork i/c centering & shuttering so as to give a rough finish strutting & propping etc. height of propping and centering below supportingfloor to ceiling not exceeding 4 m. & removal for the same for in-situ reinforced and plain concrete work in : [Using 12mm shuttering ply]

Foundations, footings, bases of columns, etc. for mass concrete

Sides and soffits of beams, beam haunchings, cantilevers, girders, bressumers and lintels not exceeding 1m in depth.

Columns, pillars, posts and struts (Square, rectangular or polygonal in plan).

Stair cases with sloping or stepped, soffits i/c risers and stringers excluding landing

BRICKWORK

2nd class (local first class) brick work in foundation & plinth in cement mortar 1:3(1 cement : 3 coarse sand)

Half brick mansonry 2nd class (local 1st class) in cement mortar 1:3 ( 1 cement : 3 c/sand ) in superstructure.

Extra for half brick masonry in superstructure above plinth upto floor two level .

Brick edging (brick laid on edge) in plinth protection with 2nd class brick local first class)i/c grouting with cement mortar 1:4(1 cement:4 fine sand).

WOODWORK

Providing wood work in frames of door, windows, clerestory windows and other frames wrought, framed and fixed in position.

Local best quality Teak.

P/F 38 mm. thick panelled, glazed or panelled and glazed shutters for doors, windows and clerestory windows i/c bright finished or black enamelled M.S. Iron butt hinges with neccesary screws.

Local best quality Teak wood.

Providing & fixing 25mm dia local best quality Uningthou curtain rods with brackets, plugs, etc. wherever required i/c painting polishing or oiling as required.

Providing & fixing bright finished brass 100 mm door mortice latch with one dead bolt & a pair of levers handles with necessary screws etc. complete (Indian make of approved quality).

Providing & fixing brass Tower bolts (barrel type) with screws etc. complete.

Providing & fixing brass handles with necessary screws etc. complete.

Providing & fixing Aluminium haning floor door stopper,ISI marked, anodised (anodic coating not less than grade AC 10 as per IS :1868)transparent or dyed to required colour and shade, with necessary screws etc.complete.

Single rubber stopper

STEEL WORK

Steel work in single sections, i/c cutting, hoisting, fixing in position & applying a priming coat of red lead paint

In M.S. Flat/Plate

In channel, angles & tees.

White ceramic glazed tiles 7.3 mm in flooring, treads or steps & landing laid on a bed of 12 mm thick cement mortar 1:3 (1 cement:3 coarse sand) finished with flush pointing in white cement.

White glazed tiles 10 mm thick in skirting risers of steps & dado on 10 mm thick cement plaster 1:3(1cement:3 coarse sand) & jointed with white cement slurry.

20x30 cm size

Providing and laying rectified ( Non-skid) Glazed Ceramic floor tiles 300x300 mm or more (thickness to be specified by the manufactured ) of 1st quality conforming to IS: 15622 of approved make in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement mortar 1:4 (1 Cement : 4 Coarse sand) including pointing the joints with white cement and matching pigments etc., complete

Marble stone slab flooring over 20 mm (average) thick base of cement mortar 1 : 6 (1 cement: 6 coarse sand) laid and jointed with grey cement slurry including rubbing and polishing complete with

White Marble slab 20mm thick

10 mm thick marble tiles in risers of steps , skirting , dado walls and pillars laid on 10 mm thick base of cement mortar 1 : 3 ( 1 cement: 3 coarse sand ) laid and jointed with grey cement slurry including rubbing and polishing complete

White

Trapzodial Profile Pre-painted profile sheet roofing of approved brand DYNA Roof or equivalent with selt drilling screws of 68mm long Xylon coated screws with PVC washer & cap complete, excluding the coat of purlinsr & trusses

Pre-painted Galvalume Sheet ( PPGL)

Trapzodial Pre-painted Profile Sheet for Ridges Gutter or Valley 610 mm wide of approved brand DYNA Roof or equivalent fixed with selt drilling screws of 68mm long Xylon coated screws with PVC washer & caps completed, excluding the coat of purlins rafters & trusses.

Pre-painted Galvalume Sheet ( PPGL)

Steel work in built up tubular trusses including cutting, hoisting, fixing in position and applying a coat of approved steel primer red oxide zinc chrome primer conforming to IS:2074-1979) welded and bolted including special shape washer etc. complete.

a ) Electric resistant welded welded tube ( Conforming to IS : 1611- 1979 )

Steel glazed windows and ventilators of standard rolled steel section joints mitred and welded with 15x3 mm lugs 10 cm long with steel plugs embedded in cement concrete block 15x10x10 cm of 1:3:6 ( 1 cement : 3 coarse sand : 6 stone aggregate20 mm nominal size ) or wooden plugs and screws of rawl plugs and screws or with fixing clips with bolt aand nuts as required including providing and fixing of 4 mm thick glass panes with glazing clips complete including applying a primer coat of approved steel primer excluding cost of metal beadings and others fittings except necessary hinges or pivots as required.

Ready made steel windows (side hung)

Ready made steel ventilators (top hung)

12 mm cement plaster 1:3 ( 1 cement : 3 coarse sand)

15 mm cement plaster1:3 (1 cement: 3 coarse sand)

Distempering (two or more coats) with oil bound washable distemper of approved quality on new work i/c priming coat of whiting to give an even shade.

Finishing walls weather shield paint of approved quality on new work (three or more coats) to give an even shade.

Finishing walls with textured exterior paint of required shade:

New work (Two or more coat applied @ 3.28 ltr/10 sqm over and including base coat of water proofing cement paint applied @ 2.20 kg/10 sqm)

Applying ready mixed priming coat pink primer of approved quality on wood work.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Painting ( two or more coats ) with synthetic enamel paint of approved quality of black or chocolate colour on wood work to give an even shade

Painting ( two or more coats ) with synthetic enamel paint of approved quality all shades except black or chocolate colour on steel on new work to give an even shade

EAVE BOARD

Providing and fixing 20mm plank as eave board with.

Uningthou wood.

Applying ready mixed priming coat pink primer of approved quality on wood work.

Painting (two or more coats) with synthetic enamel paint of approved quality of black or chocolate colour on wood work to give an even shade.

SH: Land Development

Excavation in hill Area in soil by mechanical means including cutting and treming of sides slops and disposing of excavated earth with all lift and lead upto 50 m.

M/s NE Enterprise

M/s Acura Ventures