COMPREHENSIVE MAINT TO BHIM ROAD, FAUJI ROAD, HAQIQAT ROAD AND MALL ROAD AREA OF AGE B/R-II UNDER GE (W) JRC

Amount

Demolition of brickwork or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc., but excluding ashlar facing, dressed stone work and precast concrete articles, complete all as specified & directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level)

Demolition of cement concrete (unreinforced) Roof , Floors (other than Ground floors), Beams, staircase, landing, chajjas and similar suspended work

Demolition of cement concrete (Re-inforced) of any description and in any position not otherwise specifically provided for.

M & L for Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc including brushing with neat cement slurry with 3.0 Kg of cement per Sqm complete all as specified & directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), rubbish off the debris out of MOD premises complete all as specified and directed

Taking down cement plaster/wall tiles including backing etc from brick/stone walls / concrete surfaces including raking out joints, hacking for key , scrubbing down with water etc complete all as specified and directed

Taking down chowkats or frames including shutters (without taking off shutters from the frame) not exc. 1.5 Sqm each, complete all as specified & directed.

Taking down chowkats or frames including shutters (without taking off shutters from the frame) exc. 1.5 Sqm but n exc 4.0 sqm each, complete all as specified & directed.

Taking down shutters of any description exc. 1 sqm and not exc. 2 Sqm each, complete all as specified & directed.

Taking down shutters of any description n exc. 1 sqm each, complete all as specified & directed.

Taking down, easing and adjusting shutters of any description, exceeding. 1.00 Sqm and not exceeding 2.00 Sqm each and re-fixing in the same or other opening completa all as specified and directed.

M&L for Brickwork with Fly Ash Bricks (old size), straight or curved on plan exceeding 6 metre mean radius built in cement sand mortar 1:6 complete all as specified.

M&L for except brick of any description in CM 1:6. complete all as specified.

M & L Brickwork with flyash bricks, straight or curved on plan to any radius in half brick thick walls, built in CM 1:6 Complete all as apecified and directed

M &L Providing precast cement concrete louvres and jallies Set in CM 1:4 Type B0 1:2:4 (12.50 mm graded aggregate) , 50mm thick (measured solid), including all mouldings but excluding frame Pre cast frame shall be measured separately and paid for under item 04032)

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50 X 100 MM comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugsor SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. complete all as specified and directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50 X 125 MM comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugsor SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. complete all as specified and directed.

S&F for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ choowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs fasteners shall be paid for separately). complete all as specified & directed.

S & F factory made single extruded WPC (Wood Polymer Composite) solid one side decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutterand fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer- In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)

S & F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30 mm thick size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S S `screws shall be paid separately

S&F of 35mm thick single piece Factory made wire gauge door shutters including of wire cloth (steel & aluminium XPM) manufacturing by PVC sheets printed 5mm thick on both side on frame made out of M.S tube 19 SWG, size 19mm x19 mm complete in all respect with lock rail and beautified by PVC beading all around fixed with PVC solvent cement complete all as per Drawing No CEPZ/TD-378/ ,Sheet 1/1 dated 27/12/2011 complete all as specified and as directed by Engr-in-Charge.

S&F of 35mm thick single piece Factory made wire gauge door shutters including of wire cloth (steel & aluminium XPM) manufacturing by PVC sheets printed 5mm thick on both side on frame made out of M.S tube 19 SWG, size 19mm x19 mm complete in all respect

S&F in repair factory made 18mm ( + 0.7mm) thick WPC cupboard shutter, prelaminated one side with coating of ultra voilet chemical, glossy/mat finish incl. 100% termite/water proof, fire retardant, Eco friendly, density not less than 600Kg/cbm finish at all edges for making edges lipping/bending, complete as per direction of Engineer-in-Charge and manufacturer's specifications.

Supply and fixing factory made uPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame 88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm 18mm), sliding mesh sash (26mm x 10mm) profile be inserted in required profile, frame will be fixed the wall with 8mm x 100mm long fasteners, Hardware Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. Area Not exceeding 2.00 Sqm Area Each complete all as specified and directed

S&F for Box type steel windows comprised of tubular frame and shutters made out of 1.25 mm thick MS sheet tube factory made with double side shutters wire gauged shutter & glass glazed shutter (wire cloth and glass panes will be measured and paid seperately) with side hung shutters with MS handles and MS peg stay dovetailed or welded incl 02 Nos, MS Tower bolts 150 mm long for each leaf and 8 mm square bar grill / guard bars at spacing as shown on Drg welded to MS flat iron frame work ,including other fittings ,hinges ,MS handles ,tarred hold fasts ,PCC blocks for hold fasts etc all as shown on Drg No CEPZ/TD -354/09 sheet 1/3 to 3/3 including two coat of synthetic enamel paint over one coat of red oxide zinc primer, complete all as specified and directed by Engr-in-charge.

M&L for Hasp and staple 100 mm in size, aluminium anodised, including bolt to hinge plate and fixed with screws.

S&F for continuous (piano) hinges, mild steel, bright finish width of flaps (when open ) 30 mm all as specified and directed.

S&F for Stainless steel fasteners of size 75mm long steel supports, fixed to walls, complete all as specified & directed.

S&F for Stainless steel designer handle (heavy duty) of 100mm size, fixed to drawers or cupboard shutters, complete all as specified & directed.

M & L for Magnet Ball catches with 8mm dia steel ball, and brass body and striking plate including letting in and fixed complete all as specified and directed

S&F for Butt hinges 100 mm long, stainless steel, medium weight with SS hinges pin and fixed complete all as specified.

S&F for Aluminium alloy, anodised, sliding door bolt 300 mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or castaluminium alloy and fixed . complete all as specified and directed.

S&F for Aluminium, anodised, barrel tower bolts 150 mm of extruded section and fixed. complete all as specified and directed.

S&F for Aluminium, anodised, handles 125 mm of extruded section and fixed.complete all as specified and directed.

S&F rubber lining fitted with aluminium powder coated strip, 100mm wide for door cill complete all as specified and directed.

S&F for floor door stopper of 140mm long cover plate of aluminium alloy body and tongue anodised with hard drawn steel spring, fixed in floor complete all as specified and directed

S&F for Mild steel, 300mm, ordinary rat tail rod patttern springs includding roller and roller plate complete fixed with screw or necessary welding to pressed steel door frame.

S&F stainless steel peg set of six of size 400mmx30mmx3mm size fitted with machine screw and wooden and plastic cleats (minium wt 190gms)

Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed in repair with statinless steel wire staples.

S&F for Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with statinless steel wire staples.

S&F, 4 mm thick sheet glass ordinary quality and glazing with oil putty in square not exc. 0.5 sqm in each pane , complete all as specified and directed.

S&F "as in repair" 25mm outer dia stainless steel decorative drapery rod of thickness 20 guage with stainless steel brackets near to ends with stainless steel finials with adopter for 25 mm dia drapery rod at both ends complete all as specified and directed.

Taking up or down steel tubing of 15mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store with all fittings, complete all as specified and directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc; and cutting chases for concealed water tubing ,etc., and making good, cutting not exc 10 cm girth in brick walls, complete all as specified.

Supply & fixing steel water tubing 15 mm bore medium grade galvanised with all fittings (ISI marked) fixed complete to walls, ceiling and floor. complete all as specified.

Taking up or down steel tubing of 20mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store with all fittings, complete all as specified and directed.

Supply & fixing steel water tubing 20 mm bore medium grade galvanised with all fittings (ISI marked) fixed complete to walls, ceiling or laid in floors complete all as specified.

Refixing old steel tubing 20 mm bore and connections in new or old position (walls, ceiling, floor etc.)

S&F for GI pipe 32 mm dia light grade in short length as spout pipe in sunken floor slab laid in slope to brick wall with PCC 1: 2:4 TYPE B -1

S & F inrepair Rotational moulded polyethlene water storage tanks three layers of 500 ltrs capacity ISI marked (cylindrical vergical with closed top) hoisted and fixed in position all as specified in SSR Part I including 20mm thick Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. (Minimum weight 20mm-210 gms including Dismantling of old brocken water tanks and refixing of inlet, outlet & over flow pipe etc complete all as specified and as directed.

S & F in repair Rotational moulded polyethlene water storage tanks three layers of 1000 ltrs capacity ISI marked (cylindrical vergical with closed top) hoisted and fixed in position all as specified in SSR Part I including 25mm thick Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. (Minimum weight 20mm-210 gms including Dismantling of old brocken water tanks and refixing of inlet, outlet & over flow pipe etc complete all as specified and as directed.

S & F inrepair 20mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 2 0 m m - 2 1 0 g m s . / 25mm-455gms/ 40mm - 690 gms) ®

Concealed Stop valve (ISI Marked), cast copper alloy screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of 5 mm bore and fixed.

Bib tap 15 mm bore long body, Brass CP, fancy type (long shank )., with crutch or butterfly handle screwed down screwed for iron/PVC pipe or for brass ferrule and fixed, complete all as specified.

Stop valve /Angle valve (ISI Marked), fancy type, chromium plated with long shank and cup screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron /PVC pipe or for unions of 15 mm bore andcomplete all as specified.

Supply & fixing CP Brass shower rose 200x200 mm size with with flexible brass arm 450-550mm long for 5 mm bore pipe complete

Supply and fixed Soap dish cantabile-clea (material SS finish, glossy) fixed to plugs with CP brass screws.

Supply & fixing in repair, Vitreous china squatting pan of pattern, long pan, 'Orissa pattern', size 580 x 440 mm white with integral foot rests (excl flushing cistern and flush pipe) but including provision concrete bedding CI floor trap etc complee

Supply & fixing, Vitreous china wash down water closet pan (Pedestal pattern) white (excl fixing bolts, flushing cistern and flush pipe) but including plastic water closet seat, white, closed pattern with flat bottom and cover and mild steel CP or aluminised hinging device.

S&F in repair plastic water closet seat cover, back closed pattern with flat bottom, and mild steel chromium plated or aluminised hinging device complete all as specified and directed.

S&F CP Brass Hand Shower (Health Faucet) with 8 mm dia,1.2 m long Long Flexible Tube Chrome Finish & Wall Hook for Water closet complete all as specified and directed.

Centre hole basin mixer without popup waste system with 450mm long braided hoses cast copper alloy for iron pipes 15 mm bore, screwed for iron pipe and fixed and all as specified and directed.

Supply & fixing in repair Push botton type dual flush type PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and push botton (incl brackets & flush pipe PVC 32 mm dia) capacity of 10 Litres.

Supply & fixing sink with drainage board made of stainless steel 1 mm thick with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets of angle iron and connecting union to pipe over all size 915 mm x460 mm and bowl size 400mmx300mmx 180mm complete all as specified and directed.

Fixing only in repair sink with drainage board made of stainless steel 1 mm thick with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets of angle iron and connecting union to pipe over all size 915 mm x460 mm and bowl size 410mmx330mmx 180mm complete all as specified and directed.

Supply & fixing in repair, Vitreous china wash basin, white flat back, size 550 x 400 mm excl taps, waste chain and plug and porcelain stopper but incl brackets.Complete all as specified and directed

Supply & fixing ,Vitreous China Urinal, Half stall type, white including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement, , flush pipe, grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) fixed incl supply and fixing of CP coupling, waste pipe and cp brass spreder all necessary fittings, complete all as specified and directed.

S & F corrugated waste pipe, 32 mm dia, suitable for WHBs/sinks/Urinal, including threaded PVC socket suitable for shank of waste coupling complete all as specified.

Brass CP towel rail 20mm dia 'D' type 60 cm long between flanges complete all as specified and directed.

S&F in repair PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and directed

M&L PVC (SWR) floor trap, dia of outlet in 75 mm, plain excluding grating, but including jointing with solvent cement fixed in repair.

Supply & fixing PVC grating square, 150 mm (Hinge pattern and with or without hole).

Supply & fixing in repair, 110 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls / trench with suitable clamp.

Supply & fixing , 110 mm bore PVC (SWR) bends any radius, with or without excess door.

Supply & fixing , 75 mm bore PVC (SWR) vent cowl

Supply & fixing in repair, 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls /trench with suitable clamp.

Supply & fixing , 75 mm bore PVC (SWR) bends any radius, with or without excess door.

S&F GI Tank Nipple 15mm bore all as specified

S&F GI Tank Nipple 20mm bore all as specified

S&F GI Tank Nipple 32mm bore all as specified

S&F GI Union 15mm bore all as specified

S&F GI Union 25mm bore all as specified

S&F GI Reducer 15 to 25 mm bore all as specified

S&F GI Reducer 20 to 25 mm bore all as specified

S&F GI socket 15 mm bore all as specified

M&L Non skid ceramic jointless coloured tiles, 7 to 8 mm thick (square/ rectangular) area of each tile exc 0.18 sqm but nexc 0.38 sqm in floor etc set & jointed in neat cement slury & pointed in white or coloured cement mixed with pigment to match over and including 15mm thick screed layer in cement mortar 1:6, complete all as specified and directed .

M&L Non skid ceramic jointless coloured tiles, 7 to 8 mm thick (square/ rectangular) area of each tile exc 0.18 sqm but nexc 0.38 sqm in skirting etc set & jointed in neat cement slury & pointed in white or coloured cement mixed with pigment to match over and including 10mm thick screed layer in cement mortar 1:4, complete all as specified and directed .

M&L Non skid ceramic jointless coloured tiles, 7 to 8 mm thick (square/ rectangular) area of each tile exc 0.11 sqm but nexc 0.18 sqm in floor etc set & jointed in neat cement slury & pointed in white or coloured cement mixed with pigment to match over and including 15mm thick screed layer in cement mortar 1:6, complete all as specified and directed .

M&L Glazed ceramic coloured tiles of size 450mmx300mm, thickness 7mm as in vertical surfaces such as skirting, dado, wall etc., set and jointed in neat cement slurry and pointed with coloured cement to match over and including 10mm thick rendering in cement mortar 1:4, complete all as specified & directed.

M&L Vitrified light shade ceremic tiles 600mmx1200mmx 10mm thick (Square/rectangular) polished in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 15mm thick screed bed in cement mortar 1:6, complete all as specified & directed.

M&L Vitrified light shade ceremic tiles 600mmx1200mmx 10mm thick (Square/rectangular) polished area of each tile not exceeding 0.36Sqm in skirting etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 10 mm thick rendering in cement mortar 1:4, complete all as specified & directed.

M&L for 25 mm thick (average thickness) PCC 1:2:4, type B-0 using 12.5mm graded stone aggregates as in floor by maintaing required gradient/undulation, finished even and smooth w/o using extra cement. Complete all as specified and directed

M&L Marble work Udaipur green 16mm to 18mm thick (table rubbed and polished)as in cooking platforms, treads, riser or landing of stair hall, window cill and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade of other than white and black incl cutting of 25 mm dia hole for gas pipe and incl rounding to edges complete all as specified and directed.

M&L Machine cut Kota stone slab flooring not less than 18-20mm thick (size of stone shall not less than 55cmx55cm), 75mm wide white marble border alround, laid over & including 20 mm thick screed base in CM 1:6, jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, grinding and polishing to yield mirror finish with machine, complete all as specified.

M&L Machine cut Kota stone slab not less than 16mm thick as in riser of steps, skirting, dado and pillar laid over & including 10 mm thick screed base in CM 1:4 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, grinding and polishing to yield mirror finish with machine, complete all as specified.

M&L for coloured machine pressed precast rubber moulded concrete interlocking red/yellow) paver block of any shape and size with 6-8mm white cement layer mixed with pigment and coated with epoxy coating having high glossy finish confirming to IS 15658-2006 of 60mm thickness, M-35 Grade, laid dry over and including 50mm thick sand filling under paver, properly levelled etc, including taking out existing interlocking paver block complete all as specified and directed.

M&L for concrete interlocking paver block any shape and size , Except tiles & refixing the same, complete all as specified and directed.

M&L for laying/spreading of sand as in 50 mm thick cushion to precast concrete interlocking paver block incl watering & consolidating. complete all as specified & directed.

M & L for Chequered cement concrete tile 20cmx20cmx25mm thick ,set and jointed over 20 mm screed bed in CM 1:4 and pointed in neat cement slurry in floor with grey pigment cement and pigment

M&L for 75 mm thick cement concrete type C-2, 1:3:6 (40mm graded agg) as in Sub-base to floor finishes.

Rendering 10 mm thick plaster in cement mortar 1: 3 on concrete surfaces as in ceilings finished even and smooth without using extra cement, complete all as specified.

Rendering 10 mm thick on other than fair face of brick work or concrete surface in CM 1:6, finished even and smooth without using extra cement.

M&L for 12 mm thick rendering in on Fair faces brick work and concrete surfaces of wall in CM,1:4 finished the surface even and smooth without using extra cement, mixing and including WPC @ 200ml/bag of cement, complete all as specified and directed.

Taking down cement plaster and decayed concrete of any description, upto tripple storey of building, from roof projection, chajja etc and making good the decayed portion with cement mortar 1 :3 mixed with water proofing compound as per manufacturers instruction or PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregate) including necessary form work and finally finished the surface with 15mm thick cement plaster in CM 1:3, complete all as specified and directed.

M&L for 75 mm thick cement concrete 1:3:6, type C1 (using 20mm graded agg) as in plinth protection finished even and smooth using extra cement.(incl necessary joint filling with mixture of paving bitumen & sand in 1:3)

Preparation of newly plastered surface of wall and applying two coat of oil bound distemper, white or tinted shade with and including priming surface with 1mm Thick wall care putty on walls, complete all as specified.

Complete removal of existing treatment of wall surfaces and applying two coat of oil bound distemper, white or tinted shade with and including priming surface with 1mm Thick wall care putty on walls, complete all as specified.

M&L for preparation of newly plastered external surfaces of walls applying two coats of cement based paint, white or tinted including curing before and after paint complete all as specified and directed.

M&L for preparation of old surfaces of walls of any description including washing down, rubbing, brooming down with wire brush, scrapping down smoke, roots, moulds, salts and treading oil and greasy spots, including taking down existing grass, vegetation, small trees and making good the disturbed surface with cement mortar 1:3 and applying one coat of cement based paint, white or tinted including curing before & after paint complete all as specified and directed.

M&L for preparing newly plastered surfaces and applying three coats of white wash as in ceiling etc.

M&L for preparation of new or previously untreated steel or iron surfaces of any description, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red-oxide primer.

M&L for preparing of Old painted surfaces of steel or iron surfaces of any description, over 10 cm width or girth and applying one coat of synthetic enamel paint.

M&L for preparing of new or previously untreated surfaces of wood of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer.

M&L for preparing of Old painted surfaces of wood of any description not otherwise described over 10 cm width or girth and applying one coats of synthetic enamel paint.

Dismantling of plain or corrugated AC sheeting, any gauge, thickness, including ridge etc as in roof covering.

Dismantling timber scantling 40 sq cm and over in section ,in any position etc complete all as specified & directed

M& L for PCC 1:2:4 type B-1 using 20mm graded crushed stone aggregate as in coping, bed plates benching,floor by maintaing required gradient/undulation etc slightly rounded or chamferred angles and throating, complte all as specified and directed.

S & F rolled section conforming to Fe-290 (Gde E-165) as in purlins,rafter,rails amd fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) incl distance pieces, cleats etc complete all as specified and directed.

S & F for Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550Mpa as in roof covering / cladding to wall, fixed with self tapping screws as specified.

Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of an colour having tensile strength of 550Mpa as in roof covering / cladding to wall, fixed with self tapping screws as specified.

S&F 1mm thick Plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 incl dismantelling of existing valley/gutter etc all as specified and directed.

M&L False ceiling of 8.00 mm thick gypsum tiles (600x600mm) laminated with PVC film on the face side & metalised polyester film on the back side with all four edges sealed with PVC film (shade either plain white or crack) fixed using T grid/Cross-T/Wall angle/level clip & suspenders of standard galvanised sections in a grid size of 600x600mm, including taking down existing ceiling board & grid work etc of any type/pattern complete all as specified and directed.

Taking down existing Aluminium door/window and refixing to the same opening after repairing, easing and adjusting incl replacement of damaged hinges, brass mortice lock, sheet glass, door closer, Elco Panel , floor spring, rubber neoprene packing, aluminium beading, glazing clips and SS screws complete all as specified and directed.( Mortice lock, sheet glass, hydraulic door closer, floor spring and composit panel to be measured and paid seperately under supply only.

S&F powder coated Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. having minimum thickness of powder coating 50 micron incl taking down complete all as specified and directed.

S&F powder coated Anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc.incl powder coating of any colour not less than 50 micron thickness complete all as specified and directed.

S&F powder coated Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) incl Powder Coating of minimum thickness of powder coating not less than 50 micron complete all as specified and directed.

Supply only Aluminium( extruded section body) Door closer hydraulically regulated, designation No. 1 universal type, suitable for door shutters up to 700 mm in width and of weight not more than 35 kg and fixed all as specified and directed.

Supply only Sheet glass 4.8mm thick ,ordinary quality fixed with aluminium beading and rubber gaskeet exc 0.50 sqm each. all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spribng clips and providing and fixing new onces exc 1.5 Sqm

Supply only for Aluminium 4 Lever Mortice lock, vertical type of size 100mm complete all as specified and directed.

Supply only for Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty. all as specified and directed.

S & F for 4mm thick Aluminium composite panel for fixing to Aluminium shutter and the like squares with aluminium beading/gasketc complete all as specified and directed.

M&L Reinforced cement concrete (nominal mix) in TypeB0 1:2:4 (12.5mm graded aggregate) for Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like

M & L for Precast reinforced cement concrete 1:2:4 type B1 (using 20mm graded crushed stone aggregate as in manhole cover slab and finishing the surface and necessary formwork complete all as specified directed by engr in charge

M&L TMT steel bars 6 to 8mm dia, cut to length bent to shape required including cranking bending etc and binding with and including mild steel wire (annealed) not less than 0.9mm dia.complete all as specified directed by engr in charge

Use and waste of formwork to soffits of WHB counter, plateform rough finished surfaces of suspended slabs such as roof slab,floor slabs landings and similar works complete all as specified and directed.

M & L 15 mm thick plaster in CM 1:4 with intergral water proofing compound and applying 75 mm thick padding and junction coved filling of PCC M-20 Nominal Mix (1:1.5:3) of 12.50mm Agg on the junction of floor and wall the surface shall than he cured and allowed to dry . Apply Epoxy Resins Coating, polymer Modified Cementation coating like brush bond of frsroc,pedilite and bostic as per manufactures instruction both on floor as well as on wall complete all as specified and directed by Engr in Charge

Supply only liquid water proofing compound Make : Dr. Fixit or STP

M&L for Cement concrete 1:5:10 type D-2 (using 40mm graded crushed stone aggregate) as in mass filling in sunken slab of toilets, complete all as specified.

Cleaning/clearing of sewage line (including manholes) 100mm to 150mm bore of any description, underground at any depth ,removing any type of blockage including desilting, descaling & dechocking of drains as well as manholes and depositing the sludge in a pit (including digging of pit) not less than 100 metres away from the site of cleaning and covering the sludge with layer of 2.5cm thick layer of earth and spraying unslacked lime on the pit and make line smooth functional all as specified and directed.

Note for ser item Nos 1.00 to 142.00 :- Rate quoted in items shall be inclusive of provision as under :- Making arrangement for establishment of centralized complaint centre in the existing building as under :- (a) Infrastructure required in Complaint cell i.e. telephone, furniture, stationery, transport and other necessary items/materials to establish a new complaint centre able to receive and manage complaints from the users by all means i.e Manual complaint mechanism, Software, Telephonic complaints mechanism, SMS complaint Mechanism and e-mail complaint mechanism and to maintain a consolidated list of complaints and its redressal mode indicating all its relevant data. (b) Computer data operator shall be able to manage all the necessary activities and having qualification as Graduate in any discipline with minimum one year certificate course of computer applications (from a Govt recognized institute). (c ) Provision and maintenance of all tools, plants, equipment and safety gear required for tradesmen under this contract. (d) Provision of communication facilities to supervisor and tradesmen. (e) Monitoring and management of complaints report from generation to execution of complaint including pending complaints. (f) Updating status of lodged complaints before change of eight hour shift. (g) Provision of motorized conveyance for deployment to all tradesmen under this contract. (h) Basic inputs to be noted from the complainants will be locality, Building No, Qtr No, Name and Rank of complaint and exact nature of complaint and mobile No/ telephone. (j) On lodging the complaint, the Complaint No will be assigned for reference. Also system should indicate an approximate time for repairs. Accordingly a corresponding complaint slip shall be generated by the system with all relevant info. Complaint slip should be printed in triplicate and to be handed over immediately to Supervisor who shall detail appropriate tradesmen for repair with required materials/store. One copy of complaint shall be retained in complaint centre and two copies with tradesmen. (k) On both copies of complaint slip, status of the complaint attended shall be endorsed by the complaint/user. One copy to be retained by the complainant and second copy to be with tradesmen for handing over in the complaint centre. Reasons for non attending of complaint etc shall be recorded alongwith estimate of expected time to attend and rectifying the complaint. (l) At the end of each day, summary of complaints shall be prepared and generated indicating No of complaints lodged, attended in time, reasons for not attending , probable time required for attending the pending complaints etc. (m) JE in charge of MES will review the complaints recorded in the system daily and will carry out personal inspection of complaints attended and its status and will take remedial measures in this regard. (n) AGE will visit the complaint cell at least thrice a week and GE at least once a week to check the efficacy of the system and record their remarks accordingly. Note : Contractor shall be responsible for followings :- (i) Installation of landline telephone connection with internet broadband facility, obtaining SIM cards for mobile phones for supervisor and workers, deployed by the contractor. (ii) Implementation of Bio-metric system for attendance of supervisors and workers, deployed by the contractor. (iiii) Payment of telephone bills, internet charges, mobile bills, expenses etc shall be borne by the contractor and no claim whatsoever on this account will be admissible by the department.

SARASWATI CONSTRUCTION CO (BID ID -3475099)

M/S Mittal Builders (BID ID -3475367)