Turnkey works for setting up of RBD Office at AIIMS, New Delhi

Amount

CIVIL WORKS

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm

1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C. kitchen and the like consisting of : i) I course of applying cement slurry @ 4.4 Kg/ sqm mixed with water proofing compound conforming to IS: 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. ii) II course of 20 mm cement plaster 1:3 ( 1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. iii) III course of applying blown or residual bitumen applied hot at 1.7 kg per sqm of area. iv) IV course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 Kg/ sqm.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigment etc., complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineerin-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with Zinc coating of 120 gms/ (both side inclusive), consisting of floor and ceiling channel 50 mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete. 75 mm overall thickness partition with 12.5 mm thick double skin fire rated board conforming to IS : 2095 : part I

Providing and fixing 12 mm thick frameless toughened glass partition of approved brand and manufacture, including top & bottom fixing arrangement counter opening and making necessary holes etc. for fixing required fittings, all complete as per direction of Engineer-in-charge

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double action hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-incharge (Door handle, lock and stopper etc.to be paid separately).

Vinyl Etching Glass Stickers: Supply and pasting of Vinyl Etching film in approved size and design in glass partition and door as per the instruction of Engineer in Charge.

Providing and fixing of frameless glass door SS Patch Lock with out handle in toughened glass including all necessary screws etc. complete.

Providing and fixing both side 2 nos SS H handle having min 450 mm length in toughed glass door including all necessary screws etc. complete.

Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90 mm x 45 mm having single rebate of 32 mm x 15 mm to receive shutter of 30 mm thickness. The laminate shall be moulded with fire resistant grade unsaturated polyester resin and chopped mat. Door frame laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fiber glass from all sides. M.S. stay shall be provided at the bottom to steady the frame.

Providing and fixing to existing door frames. 30 mm thick Fiberglass Reinforced Plastic (F.R.P.) flush door shutter in different plain and wood finish made with fire retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate all around, with suitable wooden blocks inside at required places for fixing of fittings and polyurethane foam (PUF)/Polystyrene foam to be used as filler material throughout the hollow panel, casted monolithically with testing parameters of F.R.P. laminate conforming to table - 3 of IS: 14856, complete as per direction of Engineer-in-charge.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete.

Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 250x10 mm

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade: Two or more coats on new work

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing 18 mm thick gang saw cut, mirror, polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 ( 1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade Area of slab upto 0.50 sqm

Extra for providing opening or required size & shape for wash basin/kitchen sink in kitchen platform, vanity counter and similar location in marble/granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Zebra Blinds: Providing and Fixing Zebra blinds for windows with approved colours as per Indian standards with following Specification Head Rail, Bottom Rail: Made of extruded aluminium powder-coated with high mechanical strength, UV resistant, anti-fogging polyester powders, expressly made for accessories to set inside IG units. Ladder Tape, Cords provided with 100% Polyester, Excellent dimensional stability and high mechanical & UV resistance. Modular and durable Chain for vertical movement.

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Plumbing Works

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Flat back wash basin size 450x300 mm with single 15mm C.P. brass pillar tap

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

Supplying and fixing CP Health Faucet superior quality ( Jagur or equvalent make ) including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid pipe; 32 mm dia

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore

Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. 15 mm nominal bore with 30cm length

Supplying and fixing PVC Floor Trap 100mmx75mm size without Jali including cutting open, boring through RCC slabs and making good the damages.

Providing and fixing SS grating of approved quality and colour. Rectangular type with openable circular lid 150 mm nominal size square 100 mm diameter of the inner hinged round grating

Supplying and fixing CP Towel rod 60cm or nearest available length including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

Supplying and fixing Stainless steel soap dish including cost of materials and labour charges etc complete as per the direction of site Engineer-in-charge.

Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer-in-Charge. Concealed work,including cutting chased and making good the wall etc.

20 mm pipe 12 Kgf/cm2

25 mm pipe 12 kgf/cm2

50 mm pipe 10 kgf/cm2

110 mm pipe 6kgf/cm2

Providing and fixing PVC pipes includes joints of pipes with one step PVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.

32 mm dia 10 Kgf/cm2

50 mm dia 10 Kgf/cm2

110 mm dia 4 Kg/cm2

FURNITURE WORKS

Ergonomic Modular Workstation - Workstations with average size of 600mm width X 750mm height having straight or curved top of optimum ergonomics as per approved drawings and direction of Engineer in charge. Both side Laminated Table top with MDF board of 18 mm thick and Frames and other panels shall be made up with pre-treated powder coated steel tubes and sheet having thick ness not less than 1.2mm as per the design that allows for any time easy modifications and durable powder coat finish in multiple colours and premium grade laminates inlays to match decor. All plywood edges to be fixed with PVC edge bands of 2mm thick and should be factory fixed. Cable Grommets and Powder coated Flip sockets with min 3 nos universal type power socket, 2 data points and 2 usb ports on table top , divided power and control wire ways from end to end. Key board tray with telescopic slides (nylon roller slides) of size 600mmx350 mm made out of 18mm thick pre laminated MDF board with decorative laminate on both side and pvc edge beeding. All works in approved colour and design as per the drawings/ images/ direction of engineer in charge. Elevation Area to be measured.

Ergonomic Cabinet L shape Modular Workstation - Workstations with average size of 600mm width X 750mm height having straight or curved top of optimum ergonomics, L shaped as per approved drawings and direction of Engineer in charge. Both side Laminated Table top with MDF board of 18 mm thick and Frames and other panels shall be made up with pre-treated powder coated steel tubes and sheet having thick ness not less than 1.2mm as per the design that allows for any time easy modifications and durable powder coat finish in multiple colours and premium grade plywood laminate inlays to match decor. All plywood edges to be fixed with PVC edge bands of 2mm thick and should be factory fixed. Cable Grommets and Pop up hydraulic sockets with min 3nos universal type power socket,2 data points and 2 usb ports on table top , divided power and control wire ways from end to end. Key board tray with telescopic slides (nylon roller slides) of size 600mmx350 mm made out of 18mm thick pre laminated MDF Board with decorative laminate on both side and pvc edge beeding. All works in approved colour and design as per the drawings/ images/ direction of engineer in charge. Note: Outer Elevation of both Sides Shall be measured

Individual Work Station Storage Unit: Storage Unit of size 450mm Length x 670mm Height x 450mm Depth made up of decorative laminated 18mm thick MDF Board in matching colour of workstation with 3 nos of drawer unit ( min heights for top drawer of 120mm, for middle drawer of 150mm height and for bottom drawer of 300mm. ) with suitable drawer channels having roller wheels. Also includes 4 nos of suitable wheels to be fixed in bottom in concealed manner, Individual chromium finished 100mm handles, Single locking system for 3 drawers, 2mm thick edge beading etc all complete as per the drawings/ images/ direction of engineer in charge.

Providing & fixing Toughened Glass Partition (8mm thick, 450mmx300mm, Single Rounded Edge) on workstation tables

Providing & fixing Magnetic Board for Front of tabletop (900mmx300mm,Both Rounded Edge) on workstation tables including supply of 6nos magnetic board pins.

Document Storage shelf: Providing and fixing of Wooden Shelf with Door laminated cabinets of length 900mm x height 2500mm made up of Pre-laminated MDF Board, exterior Grade-I 18 mm thick confirming to IS: 14587 with decorative lamination on both side with proper provision of racks and shelves. Storage unit of 400 mm deep with wooden shelves @ 500mm c/c. Each Shutter shall be fixed with 4 Nos of Hinges and Door Handles of 125mm size. All the edges to be finished with edge band and shelves to be fixed with proper bracket holders complete as per approved layout, drawings and instruction of Engineer in Charge. Note: Only front elevation will be measured.

Over Head Storage Cabinet: Providing and fixing of Over head storage cabinet of dimension 900mmX600mmX450mm made up of Pre-laminated MDF Board, exterior Grade-I 18 mm thick confirming to IS:14587 with decorative lamination on both side including inside middle partitions and with sliding door on front side with rollers, sliding channels, handles, locks etc. All the edges to be finished with edge band and shelves to be fix with proper bracket holders complete as per approved layout, drawings and instruction of Engineer In Charge. Note: Only front elevation will be measured.

Conference Table having standard size suitable for 10 seater or as per approved drawing, made up with flat pressed 3 layer & graded (medium density) Grade I, Type II conforming to IS: 12823 (exterior grade) Prelaminated particle board, round at the corners, top made of 36mm thick board, pressed with 0.4mm thick membrane foil clad pressed with PU glue. The foil shall be pre-coated with a layer of polyurethane for better scratch resistance. The table shall have under structure with verticals made of 25mm thick post-formed particle board & modesty made of 18mm thick pre-laminated particle board having decorative laminate on both sides. Table shall also have shelf below made of 18mm thick pre-laminated particle board. The Round corner piece shall be made up of 36mm thick board pressed with 0.4mm thick membrane foil clad pressed with PU glue and supported with post of 65mm dia. made of CRCA sheet duly powder coated as per salient technical features. The table should be only in one approved colour. The table shall also have provision for carrying wires & mounting switches etc. necessary provision for wire management, data/computer/telephone cabling. 3 Nos Flip box with 3 Nos Electrical Plugs and network Connectivity Ports in each box.

Executive Chair : Medium back ergonomic chair with headrest, five nos. star shaped Nylon base 640mm diameter, Castors: 50mm diameter nylon twin wheel, gas lift height adjustment, back angle adjustment and backrest height adjustment. Adjustable armrest providing natural resting for arms. Seat with PU cutted foam backed fabric, back rest with mesh type fabric, Upholstery: Heavy duty rubber backed fabric in BLACK.

Office Chair: Non-revolving executive chair with fixed armrest providing natural resting for arms. Seat with PU cutted foam backed fabric, back rest with mesh type fabric, Upholstery: Heavy duty rubber backed fabric in BLACK ( Size -55x60 cm)

Visitor Chair :Executive mid back cantileaver mesh chair overall size 600*520*550 mm. Chair to come in high quality fabric seat with pu foam and mesh back . Chair to be supported by chrome plated metal tube that holds the back and seat as one piece. Recommended make Godrej visitor or equivalent.

3 seater Sofa for visitors: - Supply and placing of 3 seater sofa finished with Fabric of approved shade & pattern, supported on wooden legs and frame. Contemporary design of elegance and comfortable, Covered with top-quality Imported Fabric upholstery as per approved colour/patterns. Sponge: high quality polymeric urethane foam 40 minimum density as the difference part, seat and back. Spring: imported spring for strong support. Minimum dimension W x H x D: 210 cm x 83.82 cm x 78.7 cm

Electrical Works

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in recessed medium class PVC conduit, making good the damages made in wall etc with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. Group C

Wiring for light/power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. (Recommended Material : Polycab, RR Kabel, V Guard, Havells)

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.( Recommended Material : RR Kabel/National/ Ralison/RKG/ Finolex / Polycab / Havells)

2 x1.5 sq.mm + 1x 1.5 sq. Mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

2 X 6 sq. mm + 1 X 6 sq. mm earth wire meter

Supplying and fixing 3 pin 5 A ceiling rose on the exising junction box / wooden block including connections as required.

S/F light plug point modular type accessaries : Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection, painting etc as required,

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs tobe used in non residential buildings).

S/F Power plug point with modular type switch : Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 15/16 and 15/16 amps modular switch, connection,painting etc as required.

S/F 20A SPN MCB industrial socket outlet : Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A, “C” curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

S/F 'C' series, MCB : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

S/F 'C' series, MCB : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Triple pole

Supplying and fixing following rating, four pole, (three phase and neutral), 415 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 100A

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 100 amps

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 8 way double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (but without MCB's and incomer) as required .(Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 8 way (4 + 24), Double door

Supplying and fixing DP sheet steel enclosure on surface/ recess along with 25/32 A 240 V "C" curve DP MCB complete with connections, testing and commissioning etc. as required

Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required. 3.5 core 35 sq mm with factory made clamp

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 2 X 10 sq. mm (19mm)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required. 3.5 X 35 sq. mm (19mm)

Supply, Installation, testing and Commissioning of three phase electronic type energy meter with LCD display with battery backup, class 1.00 CT. The whole unit to be mounted on suitable metal enclosure (powder coated with locking arrangement, separate enclosure for incoming and outgoing) with required HRC fuses/MCB/RCCB as required, Neutral link and all connections complete

Supply, installation, testing and commissioning of the following types of light fittings with all accessories on false ceiling, true ceiling or wall as directed and giving connections with 16/0.20 mm 3 core PVC insulated and sheathed round copper conductor flex wire or extending the original wiring and giving connections as required. All recessed type fixtures are to be supported independently with chains or GI wire anchored to the ceiling with anchoring bolt of necessary size. All loose wires above the false ceiling are to be neatly concealed by flexible metal/pvc conduits.( cost to include lamps & all consumables also)

Supply and installtion of 30-36W, 230V, 4300 lumen, Surface/Recessed Square LED Cool White light fixture of dimession 600mm X 600mm on false ceiling along with all accessories with intergrated driver THD<10% and connections as well as making good the damages as required at site Engineer. Recommended makes: Philips/Crompton/Wipro or equivalent.

Supply and installtion of LED tubelight of 6000K and 20-24W on wall or ceiling as directed and giving connections as required. All loose wires are to be neatly concealed. (Make: Philips, Wipro, Crompton or equivalent)

Supply and installtion of 10-15W, 230V, Surface/Recessed Square or Round LED Cool White light fixture on false ceilling along with all accessories with intergrated driver THD<10% and connections as well as making good the damages as required at site Engineer. Recommended makes: Philips/Havells/Wipro or equivalent.

Supply, Installation, testing and commissioning of wall mount fan (400mm sweep), adjustable speed. min 60 degree oscillation, swing, Adjustable upward and downward tilt mechanism, Protective Guard, Including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, mounting accessories, etc. as required. It shall be double ball bearning type. (Make: USHA, Cromption , Havells)

Supply, conveyance, installation, testing and commissioning of ceiling fans of the following sizes using standard accessories excluding resistance type regulator, wiring the down rod with PVC insulated and PVC sheathed 650/1100V grade 3 core round copper conductor flex wire or with extended original wiring etc. as required. 1200mm sweep - 3 star rated, 3 blade ceiling fan complete with 300mm down rod , canopies, shackles. (Make: USHA, Cromption , Havells)

Supply, Installation, testing and commissioning of exhaust fan in the existing opening having 1300-1400 rpm motor speed and 150 mm sweep. bearning type. (Make: USHA, Cromption, Havells or equivalent)

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Network /LAN works

48 Port Network Switch : Supply, Installation, testing and commissioning of : 10/100 Mbps 48-Ports Gigabit Switch with minimum 2 SFP modules . ( Make : D-Link/TP-Link/Netgear)

S/F Modular boxes, base & cover plate : Supplying and fixing 1 or 2 module ( 75 mm x 75 mm), GI box along with modular base, cover plate for modular switches in recess etc as required.

Providing and Fixing of RJ-45 socket outlet in the existing modular box with connections and all required.

Supplying,drawing and crimping with all accessories of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.1 run of cable from Port Switch to Data socket

Supply, installation, testing and commissioning of best quality cat-6 patch cord having 1 metre length complete as per specifications as required.

Supply and fixing of 2U wall mounting rack of dimension WxDxH (550 x 400 x 170 mm), along with supply and fixing of mounting brackets for support Lockable Front Door and Detachable Side Doors, Cable Manger and PDU of 4 or 6 sockets, with including cooling fan with accessories complete

Supply and Integration of Business IP Phone compatible with PoE and IP PBX system, having LCD Display of size minimum 2 inch along with accessories complete. Make: Matrix/Grandstream/Clixxo or equivalent.

Supply, Installation, and Integration of IP PBX Switch having capacity of minimum 80 concurrent calls, 50 attendee conference, Integrated 4 PSTN Trunk FXO Ports Plus 2 FXS Ports, Highest level of security protection using SRTP, TLS and HTTPS encryption, Supports up to 500 users, 80 SIP trunk accounts, minimum 1.5GHz Quad-core processor, 1GB DDR RAM, 8GB EMMC Flash,Built-in Call Detail Records (CDR) for tracking phone usage by line, date, etc. Make: Matrix/Grandstream/Clixoo or equivalent

Supply and connecting 2 mtr long CAT6 cable Patch cord having RJ45 connectors crimped at both ends, to the existing outlets as required. Make: D-Link/TP-Link or equivalent

Fire Fighting

Supply of ABC Type fire extinguisher of 2 Kgs. Make SAFEX / MINIMAX / CEASEFIRE or equivalent

Supply, Installation, Testing & Commissioning of Indoor IR Dome night vision cameras : 2.0 MP, 0.1 lux, Resolution 720 P ,AWB/ BLC/ AGC, min 20m range, Built-in IR illumination, white color case, PAL-CE/FCC approved. Make: CP PLUS/HIKVISION/Honeywell or equivalent

Supply, Installation, Testing & Commissioning of Outdoor IR Bullet night vision camera :2.0 MP,0.1 lux, Resolution 720 P,AWB/ BLC/ AGC ,min 20m range, Built-in IR illumination, white color case, DC12V, PAL-CE/FCC approved. Make: CP PLUS/HIKVISION/Honeywell or equivalent

Supply, Installation ,Testing & commissioning of Network Video Recorder : 16-Channel Embedded 4k, Real-time, with 4 TB HDD. Rate shall be inclusive of all accessories, termination of cables, etc complete. Make: CP PLUS/HIKVISION/Honeywell or equivalent

Supply and Installation of LED Color Monitor of minimum 22 inch screen, complete, FHD display Make: LG/Samsung or equivalent.

Providing 4U Rack including accessories. Make:CP Plus, Netrack

Supply and Installation of SMPS Power Supply Unit of 230V, capacity miniumum 450W including accessories

Supplying,drawing and crimping with all accessories of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required.1 run of cable from Port Switch to Data socket

Capital/Supply Item works

Supply, Installation, Testing and commissioning of 10 kVA True Online UPS system as per IEC 62040-3 with 415 +/- 15% V, 50 Hz, Single Phase input & Single Phase Output woring on 16 bit Microprocessor architecture, with inbuilt isolation transformer, 1 hour battery back up, battery rack accessories, suitable copper cabling work from incoming switch and to outgoing switch is also under contractor scope. Make: Liebert/Numeric/APC

Water Dispenser: Supply and errection of water dispenser can hold 20 litre water bottle having normal standing design with 14 liter refrigerator at bottom and having 3 temperature taps hot, plain and cold. 3 liter cooling and 5 liter heating capacity per hour. Body made of ABS plastic and tank made of Food grade stainless steel. Heavy duty bottle piercer with bottle holder. with min 1 year warranty. (Make : voltas / Blue star/ equivalent)

Air Conditioning

SITC of Inverter Air Conditioner: Supply, installation, testing and commissioning of Air Cooled High Wall mounted Split Air Conditioner of following capacity consisting of high wall mounted type room unit (fan coil) with cordless remote control and one number outdoor condensing unit comprising of enegy efficient suitable rotary compressor for operation on single phase, 230 V, 50Hz supply, fixing the outdoor unit on a raised platform as per manufacturers recommendation and fixing of room (fan coil) unit on wall, standard 3 m distance refrigerant copper piping with 13mm nitrile rubber insulation, providing and making interconnection between room & condenser as per site conditions, comprising of 1" dia drain PVC pipe with insulation 3m, canvas connections, full electrical cabling from power plug near indoor unit and to outdoor unit, ODU MS stand, first charge refrigarant gas, suitable stabilizer etc complete as required. ( Make : Voltas, Carrier, Blue Star, Siemens, Hitachi ) :2TR 3 star rated as per BEE

Supply and Installation of additional copper, drain piping with proper insulation in PVC truncking of size 100mm x 50mm and additional cable complete on wall/above false ceiling etc all complete.

Video Conference Works

Supply, Installation, Testing and commissioning of 55 inch LED Display having, Resolution: 4K Ultra HD (3840 x 2160) | Minimum Refresh Rate: 60 Hertz, Connectivity: minimum 2 HDMI ports to connect set top box, Blu Ray players, gaming console, Video conference units | minimum 2 USB ports to connect hard drives and other USB devices Sound : Minimum 20 Watts Output | Dolby Audio | Clear Sound, OS: Android/Google TV, Display: 4K Processor | 4K HDR, Operating System – Android Hardware Interface - Ethernet, Composite Video, Bluetooth 5, Mount – Movable Wall Mount Remote control. Make: Sony/TCL/Vu

Supply, Installation, testing and commissioning of All in One Video Conference Unit having following specifications: 1) Camera Full HD 1080p video calling (up to 1920 x 1080 pixels) at 30 frames-per-second7 • H.264 UVC 1.5 with Scalable Video Coding (SVC) • • minimum 90-degree field of view with autofocus • 4X digital zoom in full HD • Digital Pan, Tilt and Zoom from remote control or optional downloadable app • Mechanical tilt • Camera LED for active streaming indication 2) Speakerphone • Integrated full duplex speakerphone with echo and noise cancellation • 360-degree wideband audio with 12-foot diameter range • Bluetooth® and NFC enabled • LEDs for speakerphone streaming, mute, hold, and Bluetooth® pairing • Controls for call answer/end, volume, mute

Microphones – Two omni-directional microphones supporting 12-ft diameter range Speakers – Frequency response: 140Hz – 16KHz Connectivity Screen mirroring through WiFi connection to the device • HDMI connector for TV output Make: Logitech Conference cam Connect/Poly Studio

Supply, Installation, of Laptop computer. 12th Generation Intel® Core™ i5/ AMD Ryzen 5 5th generation processor, Genuine Windows 11 Single language, MS Office, Intel® UHD Graphics with shared graphics memory, minimum 1.7 GHz base clockspeed, 8 GB, DDR4, 3200MHz, 512GB SSD, 23.8 inch FHD (1920x 1080), Anti- Glare Narrow Border Non Touch Display, mouse and mouse pad. Make : Dell / HP or equivalent

Logix Solutions

M.H.HAZARIKA ENTERPRISE

panwar construction company

Mahendru Consultants

R S Enterprises

MUSHTAQ AHMED KHURWANI