CERTAIN B/R REPAIR TO OTM AND MD ACCN INCLUDING DAILY COMPREHENSIVE MAINTENANCE SERVICES IN ZONE B AT SUNJUWAN UNDER GE JAMMU

Amount

B/R Portion: - Taking down chowkhats or frames with shutters (without taking off shutters from the frames) of size not exceedng 1.5 Sqm each complete all as specified and as directed by Engineer-in-Charge.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) of size exceeding 1.5 Sqm but not exceeding 4.0 Sqm each complete all as specified and as directed by Engineer-in-Charge.

Taking down shutters of any description, area exceeding 1.00 Sqm and not exceeding 2.00 Sqm each complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing 1.25 mm thick pressed steel frames of size 105mm x 60mm for single doors including necessary fixing lugs, hinges, lock strike plate, etc complete all as per IS provisions all as specified and as directed.

Supply and fixing 1.25 mm thick pressed steel frames of size 125mm x 60mm for single doors including necessary fixing lugs, hinges, lock strike plate, etc complete all as per IS provisions all as specified and as directed.

Material and labour for PCC (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) as in filling in chowkhats, hold fast block etc. complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing 30 mm thick flush shutters for door solid core construction, with block board core and ply wood face panels with lipping to match complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing second class hard wood plain, framed, panelled shutters 30mm thick, (any number of panels) with panels of timber flat on both sides (feather edged) or of veneered particle board medium density wood particle board with commercial faces veeners supplied and fixed to chowkats complete all as specified and as directed.

Supply and fixing second class hard wood, glazed and skeleton shutters 30mm thick, open rebated and prepared to receive glass, gauze, etc without sash bar, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing gauze etc, size of members, supplied and fixed to chowkhats complete all as specified and as directed.

Supply and fixing stainless steel wire mesh 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed.

Material and labour for preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint (Ordinary tint) over a coat of pink primer complete all as specified and as directed.

Supply and fixing 100 mm long, butt hinges, medium weight, cold rolled mild steel complete all as specified and as directed.

Supply and fixing 150 mm long mild steel barrel tower bolts, stove enamelled black, with bright bolt and fixed complete all as specified and as directed.

Supply and fixing 150 mm long mild steel pressed handles, oval type, stove enamelled black complete all as specified and as directed.

Supply and fixing 250mm long mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and as directed.

Supply and fixing aluminium alloy, anodised, sliding door bolt 250mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and as directed.

Supply and fixing factory made solid PVC moulded door shutter with particle board core 28 to 30 mm thick (Stiles), with 2, 4, or 6 raised panel design with 2mm thick moulded PVC sheet on the front face and 2mm plain colour PVC sheet on back face, supplying and fixing in frame at site as per specification and drawing all as specified and as directed.

Supply and fixing factory made single extruded WPC (Wood Polymer composite) solid door/ window/ ceosetory windows and other frames/ chowkhat of size 65 x 100mm comprising of virgin PVC polymer of K value 58-60 (Suspension grade) Calcium carbonate and natural fibres (wood powder/ rice husk/ wheat husk) and non toxic additives (Max toxicity index 12 for 100 gms) fabricated with mitred joints after applying PVC solvent cement and screwed with full body threaded star headed stainless steel screws having minimum frame density of 750 kg/cum, screws withdrawal strength of 2200N (face) and 1100N (Edge), minimum compressive strength of 58N/mm², modules of elasticity 900N/mm² and resistance to spread of flame of class 'A' category with property of being termite/ borer proof water/ moisture proof and fire retardant and fixed in position with mild steel hold fasts/ lugs/ stainless steel dash fasterners of required dia and length complete as per the directions of Engineer-in-Charge. (Mild steel hold fasts/ lugs/ stainless steel dash fasteners shall be paid separately).

Supply and fixing 100 mm long, butt hinges, stainless steel, ISI marked complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing 150 mm long aluminium, anodised, barrel tower bolts of extruded section complete all as specified and as directed.

Supply and fixing 150 mm long extruded aluminium alloy handles, fabricated type, anodised complete all as specified and as directed.

Supply and fixing in repairs 250 mm long sliding door bolt, plate type, mild steel, stove enamelled black with bright bolt of not less than 12 mm dia with and including a minimum of six bolts and nuts, four on bolt plate and two on staple plate complete all as specified and as directed.

Supply and fixing in repairs 150 mm long mild steel, barrel tower bolt, stove enamelled black with bright bolt, ISI marked complete all as specified and as directed.

Supply and fixing in repairs 150 mm size mild steel, stove enamelled black, pressed handles, oval type complete all as specified and as directed.

Supply and fixing in repairs mild steel 300mm ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed.

Supply and fixing in repairs 100 mm long butt hinges, medium weight, cold rolled mild steel complete all as specified and as directed.

Supply and fixing in repairs aluminium anodised, barrel tower bolt of extruded section, size 150 mm complete all as specified and as directed.

Supply and fixing in repairs aluminium handles, cast type, anodised, size 150 mm complete all as specified and as directed.

Supply and fixing in repairs 200mm long aluminum tower bolt complete all as specified and as directed.

Supply and fixing in repairs 300mm extruded aluminum sliding door bolts plate type cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium section alloy and fixed in any position complete all as specified and as directed.

Supply and fixing in repairs stainless steel wire mesh 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed.

Supply and fixing aluminium frame powder coated of any colour as approved (Thickness of powder coating not less than 50 micron) for doors, windows, ventilators, partitions, with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed. Note: - Frame to walls etc shall be fixed with PVC rawl plugs and steel screws of length not less than 75mm at places as directed. Quoted rate shall be deemed to include the same.

Supply and fixing aluminium window and ventilator shutters, powder coated of any colour as approved (Thickness of powder coating not less than 50 micron), side hung type without sash bars, aluminium sections including necessary joining cleats, glazing clips, powder coated aluminium snap beading, screws, with aluminium grills complete all as specified and as directed. Note: - Glass and rubber neoprene packing/ rubber gasket shall be measured and paid for separately as “Supply only” under respective item of this Schedule.

Supply and fixing powder coated aluminium sliding window (three track) consisting of two shutter of glazed and one shutter of flyproof. Note: - The item shall be included as following: - (a) Aluminium powder coated frame of section 100 x 44 mm x 1.5 mm with or without rebate. (b) Aluminium powder coated window shutters of section 40 x 20 mm x 1.5 mm thick (Two shutter of glass and one shutter of wiremesh) including self locking catch and roller etc. (c) 5.5 mm thick coloured or tinted glass glazing as in aluminium door/ window/ ventilator with aluminium hollow beading/ glazing clip (included with shutters) size 19mm x 17mm made out of 0.70mm thick hollow section weighing not less than 0.97 Kgs/RM including rubber gasket. (d) Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples.

Supply and fixing 4.8mm thick sheet glass, ordinary quality and glazing with oil putty/ rubber gasket in square of any thickness in each pane for metal frames complete all as specified and as directed.

Dismantling boarding in any description fixed in any position with nails/ screws complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing for 18 mm thick single side prelaminated wood grain solid PVC sheet suitably fixed in shelves; Partitions and shelves of built-in cupboards, almirahs, book cases, toilet boxes, racks, pelmets and similar work including all hardware fittings (stainless steel Auto hinges, stainless steel designer handle, locking arrangement etc) as per direction and specifications.

Material and labour for 12mm veneered decorative plywood, grade - 1 (with BWR resin) with decorative face veneers on both faces, fixed with screws as in shelves to kitchen almirah and cupboard complete all as specified and as directed.

Supply and fixing 1mm to 2mm thick sunmica fixing to ply wood complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing Teak wood beading 20 mm wide complete all as specified and as directed.

Supply and fixing 75 mm long, butt hinges, medium weight, cold rolled mild steel complete all as specified and as directed.

Supply and fixing hasp and staple 100 mm aluminium anodised, safety type with mild steel hinges pin including bolt to hinges plates and fixed with screws complete all as specified and as directed.

Supply and fixing 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified and as directed.

Supply and fixing in repairs hasp and staple 100 mm aluminium anodised, safety type with mild steel hinges pin including bolt to hinges plates and fixed with screws complete all as specified and as directed.

Supply and fixing in repairs 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified and as directed.

Supply and fixing in repairs of floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor with overall length of vover plate 140 mm complete all as specified and as directed.

Supply and fixing in repairs door closer of aluminium (die cast) body, hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851mm to 1000mm width and of weight between 61 to 80 kg, ISI marked complete all as specified and as directed.

Supply and fixing in repair toilet paper holder, brass chromium plated, fancy type complete all as specified and as directed.

Supply and fixing 15mm dia toilet paper holder chromium plated bars including taking down old one complete all as specified and as directed. Make: - Jaquar Cat Part No AHS 1551 BP or equivalent in makes as specified in Group - 1 of Appx 'F'.

Supply and fixing in repair 75mm Aluminium mortice lock vertical type 4 lever complete all as specified and as directed.

Supply and fixing in repair of brass magic eye at door entrance complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repair 450 x 300 mm cabinet mirror 5 mm thick of high quality glass, seamless finish, light weight, high strength complete all as specified and as directed.

Supply and fixing in replacement steel plate racks of size 900 x 900mm complete all as specified and as directed.

Supply and fixing in repair curtain drapery rod 25 mm dia, mild steel, chromium plated, fancy type with fixing brackets and knobs at both ends as per site requirement complete all as specified and as directed by Engineer-in-Charge. Note: - The cost of brackets and knobs is deemed to be included in the quoted rate. Nothing extra shall be paid on this account.

Supply and fixing in repairs drapery curtain rod of metallic 20mm dia covered with PVC coating complete with mild steel bracket golden colour rings and side caps fixed in position by drilling holes in walls and fixed the brackets with rawl plug and steel screws complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing in repair stainless steel tubular towel rail 20 mm dia 'D' type, 600 mm long complete all as specified and as directed.

Supply and fixing in repair chromium plated soap dish, fancy type fixed to wall with chromium plated brass screws complete all as specified and as directed.

Supply and fixing 15mm dia soap dish chromium plated bars including taking down old one complete all as specified and as directed. Make: - Jaquar Cat Part No AKP-35731P or equivalent in makes as specified in Group - 1 of Appx 'F'.

Taking down old rusted and damaged steel window/ vent including guard bar and grill where exist of size not exceeding 1.5 Sqm each complete all as specified and as directed.

Supply and fixing box type steel windows comprised of tubular frame and shutters made out of 1.25 mm thick mild steel sheet tube factory made with double side shutters wire gauged shutter and glass glazed shutter with side hung shutters with mild steel handles and mild steel peg stay dovetailed or welded including 02 No's, mild steel tower bolts 150 mm long for each leaf and 8 mm square bar grill/ guard bars at spacing as shown on drawing welded to mild steel flat iron frame work, including other fittings, hinges, mild steel handles, tarred hold fasts, PCC blocks for hold fasts etc all as shown on drawing No CEPZ/TD -354/09 sheet 1/3 to 3/3 including one coat of red oxide zinc primer. The following items shall also be included in quoted rate of this item: - (a) 3 mm thick sheet glass ordinary quality and glazing with oil putty in square. (b) Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples.

Supply and fixing in repair Steel ventilators with top hung shutter including hinges, steel peg stay complete all as specified and as directed.

Dismantling strucural steel work including door gates and railings but excluding framed truss etc complete all as specified and as directed.

Supply and fixing mild steel framed work as steel gates, chowkhats and other similar work of angle or other section with gusset plates rails, braces etc complete driling for fixing of steel sheeting or other covering etc, confirming to Fe 290 Grade E-165 complete all as specified and as directed.

Supply and fixing mild steel framed work as in grills, gratings etc. with ends of bars shouldered and/ or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walkways, railings, framework of water tank and similar works conforming to Fe-410-0 or Fe-310-0 complete all as specified and as directed by Engineer-in-Charge.

Material and labour for welding in repairs exceeding 2.5cm but not exceeding 5cm in length and not exceeding 6 mm thick of metal complete all as specified and as directed.

Material and labour for painting to new steel surfaces of any description not otherwise described over 10 cm in width or girth including preparation of surfaces, priming with red oxide zinc chrome primer (one coat) and finishing with two coats of synthetic enamel paint complete all as specified and as directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden/ steel frames or stone or concrete or bricks surrounds glazed with putty complete all as specified and as directed.

Supply and fixing sheet glass 3mm thick, ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sqm in each pane complete all as specified and as directed. Note: - Contractor shall have no claim on irrespective of any height and scaffolding and safety responsibility will be of contractor.

Supply and fixing figured glass, pin head type, 4mm thick and glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

Taking down or up, 15 mm bore galvanised steel tubing and connections including cleaning for refixing or removal complete all as specified and as directed.

Supply and fixing GI tubing medium grade with all fitting and fixed to walls and ceilings or laid in floors, bore of pipe 15 mm complete all as specified and as directed.

Refixing old GI tubing with all fitting and fixed to walls and ceilings or laid in floors, bore of pipe 15 mm complete all as specified and as directed.

Taking down or up, 20 mm bore galvanised steel tubing and connections including cleaning for refixing or removal complete all as specified and as directed.

Supply and fixing GI tubing medium grade with all fitting and fixed to walls and ceilings or laid in floors, bore of pipe 20 mm complete all as specified and as directed.

Refixing old GI tubing with all fitting and fixed to walls and ceilings or laid in floors, bore of pipe 20 mm complete all as specified and as directed.

Taking down or up, 25 mm bore galvanised steel tubing and connections including cleaning for refixing or removal complete all as specified and as directed.

Supply and fixing GI tubing medium grade with all fitting and fixed to walls and ceilings or laid in floors, bore of pipe 25 mm complete all as specified and as directed.

Supply and fixing in repairs bib taps brass cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule for 15 mm bore GI pipe complete all as specified and as directed.

Supply and fixing in replacement bib tap, cast copper alloy fancy type, chromium plated, long neck with crutch or butterfly handle, screwed down, suitable for 15mm nominal bore iron pipe screwed for iron or brass ferrule and fixed complete all as specified and as directed.

Supply and fixing in repair bib tap 15 mm bore, high pressure of PTMT (minimum weight 90 grams) colour approved by Engineer-in-Charge, screwed for iron pipe and fixed complete all as specified and as directed.

Supply and fixing in repair pillar taps, cast copper alloy, with capstan head, chromium plated, screwed down, high pressure with long screwed shank and fly nuts, screwed for 15mm bore dia iron pipe complete all as specified and as directed.

Supply and fixing in repair grating 75mm dia of stainless steel with and without hole having minimum weight 75 gm complete all as specified and as directed.

Supply and fixing in repair PVC grating 125 mm dia complete all as specified and as directed.

Supply and fixing in repairs stop valves/ angle valves, cast copper alloy chromium plated screwed down, high pressure, brass with crutch or butterfly handle, screwed both ends for iron pipe or for unions, for bore dia of pipe 15 mm bore complete all as specified and as directed.

Supply and fixing in repairs stop valves, cast copper alloy screwed down, high pressure, brass with crutch or butterfly handle, screwed both ends for iron pipe or for unions, for bore dia of pipe 15 mm bore complete all as specified and as directed.

Supply and fixing in repairs stop valves, cast copper alloy, screwed down, high, fancy type chromium plated, pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions 20 mm bore complete all as specified and as directed.

Supply and fixing in repairs brass chromium plated shower rose 125mm size with swivel joints, fixed complete all as specified and as directed.

Supply and fixing in repair ball valves 20 mm bore, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe of 20 mm dia (minimum weight 210 grams) and fixed complete all as specified and as directed.

Supply and fixing in repairs ball valves 25 mm bore, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe of 25 mm dia (minimum weight 455 grams) and fixed complete all as specified and as directed.

Supply and fixing in repair PVC connection 15 mm size with PTMT nuts of length 450 mm complete all as specified and as directed.

Supply and fixing in repairs 15mm dia PVC connection with brass check nut of length 600mm complete all as specified and as directed.

Material and labour for vitreous china wash basin, white, flat back, size 580 x 440mm, including brackets and cutting for and pinning in ends of brackets, fixed in repairs including 32mm bore brass chromium plated waste fitting and 32mm bore PVC waste pipe of sufficient length complete all as specified and as directed.

Supply and fixing in repairs vitreous china Squatting pan, 'Orissa' pattern, size 580 x 440 mm white, with integral foot rest excluding flushing cistern and flush pipe including connection to trap, to flushing pipe, anti-syphonage pipe, etc complete including making good to floor complete all as specified and as directed.

Supply and fixing in repairs vitreous china wash down water closet pan (Pedestal pattern) white complete including seat and cover, flush pipe including all joints complete all as specified and as directed.

Supply and fixing in repair plastic water closet seat cover, white, closed pattern with flat bottom and cover and mild steel chromium plated hinging device complete all as specified and as directed.

Dismantling rotational moulded polyethylene water storage tank of capacity exceeding 250 litres but not exceeding 500 litres complete all as specified and as directed by Engineer-in-Charge.

Material and labour for rotational moulded polyethylene water storage tanks of capacity 500 litres, (cylindrical vertical tanks with closed top) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc complete all as specified and as directed. Notes: - (i) The water storage tanks shall be 3 layers, HDPE tanks moulded to seamless perfection of rotational moulding process. The tanks shall be manufactured only from FDA approved special grade of polyethylene and shall be certified fit for portable water. (ii) The tanks shall be white coloured and ISI marked. Also refer paras 18.60 and 18.60 A of MES Schedule Part-I. (iii) Payment for inlet, outlet and over flow pipes shall be made separately. However cost of providing necessary GI fittings such as nipples with check nuts for inlet and outlet pipes, GI plug with check nut for over flow pipe and 30 cm long wash out pipe, GI 20mm nominal bore, medium grade and check nut for wash out pipes of size as per actual requirements and ball valve as directed by the Engineer-in-Charge shall be deemed to be included in the unit rate of this item.

Dismantling rotational moulded polyethylene water storage tanks exceeding 500 litres but not exceeding 1000 litres capacity complete all as specified and as directed.

Material and labour for rotational moulded polyethylene water storage tanks of capacity 1000 litres, (cylindrical vertical tanks with closed top) hoisted and fixed in position including making necessary arrangements for fixing inlet, outlet and over flow pipe and provision of wash out pipe etc complete all as specified and as directed. Notes: - (i) The water storage tanks shall be 3 layers, HDPE tanks moulded to seamless perfection of rotational moulding process. The tanks shall be manufactured only from FDA approved special grade of polyethylene and shall be certified fit for portable water. (ii) The tanks shall be white coloured and ISI marked. Also refer paras 18.60 and 18.60 A of MES Schedule Part-I. (iii) Payment for inlet, outlet and over flow pipes shall be made separately. However cost of providing necessary GI fittings such as nipples with check nuts for inlet and outlet pipes, GI plug with check nut for over flow pipe and 30 cm long wash out pipe, GI 20mm nominal bore, medium grade and check nut for wash out pipes of size as per actual requirements and ball valve as directed by the Engineer-in-Charge shall be deemed to be included in the unit rate of this item.

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and refixing in position after cleaning and removing all scale and dirt etc from tanks and from mouths of circulating pipes etc complete (capacity of tank exceeding 250 litres and not exceeding 500 litre) complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing 32mm in repair waste coupling chromium plated for wash hand basin complete all as specified and as directed.

Supply and fixing in repair 32 mm waste coupling for kitchen sink complete all as specified and as directed.

Supply and fixing in repair PVC waste pipe 32 mm bore complete all as specified and as directed.

Supply and fixing in repairs PVC valveless, syphonic action type flushing cistern, low level, white, with inlet ball valve, float and handle including brackets 10 litres capacity complete all as specified and as directed.

Supply and fixing in repair (Syphon internal fitting) of PVC low level cistern as per existing pattern to make the PVC low level cistern fully functional complete all as specified and as directed.

Supply and fixing in repair spray jet, brass chromium plated, with and including 1.5 metre long PVC flexible reinforced pipe for EWC, for bore dia of pipe 15mm complete all as specified and as directed.

Supply and fixing in repair brass chromium plated wash hand basin mixer non telephonic for mixing hot and cold water screwed down for iron pipe 15 mm bore complete all as specified and as directed.

Supply and fixing in repair brass chromium plated wall mixer non telephonic for mixing hot and cold water screwed down for iron pipe 15 mm bore complete all as specified and as directed.

Supply and fixing in repair PVC cover (lid only) for PVC water storage tank of capacity 500 litres with locking arrangement and hinges complete all as specified and as directed.

Supply and fixing in repair sinks made of stainless steel 1.0 mm thick kitchen sink with drainage board, plugs washers and waste coupling including bedding in cement mortar to dwarf wall or including supply and fixing cantilever brackets of mild steel angles and connecting union to 800 mm long PVC waste flexible pipe 40 mm dia, over all size 915 mm x 460 mm and bowl size 410 mm x 330 mm x 160 mm complete all as specified and as directed.

Supply and fixing in repair towel ring with material brass with glossy finish with fitting complete all as specified and as directed.

Supply and fixing in repair rubber gasket of 2.5 mm thickness (minimum) and width 60 mm, fixed with steel screws and black nails with plate washers to wooden door to cover the gap between door and floor complete all as specified and as directed.

Taking down eaves, gutters and rainwater pipes (any size or pattern) including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and as directed.

Supply and fixing 75 mm bore PVC (SWR) soil, waste and vent pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed.

Supply and fixing 110 mm bore PVC (SWR) soil, waste and vent pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed.

Supply and fixing in repair PVC pipe (SWR) floor trap with grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B-1, 75mm dia complete all as specified and as directed.

Supply and fixing PVC pipe (SWR) bends (any radius), diminishing pieces or tappers 110mm dia with access door complete all as specified and as directed.

Supply and fixing PVC pipe (SWR) bends (any radius), diminishing pieces or tappers 75mm dia with access door complete all as specified and as directed.

Supply and fixing PVC pipe (SWR) branch pieces, double (equal or unequal) ordinary or inverted (spigot or socket type) or with parallel branches 110 mm dia complete all as specified and as directed.

Supply and fixing in repair PVC vent cowls 110mm dia complete all as specified and as directed.

Supply and fixing in repair PVC (SWR) couplers for 75 mm bore pipe complete all as specified and as directed.

Supply and fixing in repair PVC (SWR) couplers for 110 mm bore pipe complete all as specified and as directed.

Supply and fixing in repair PVC (SWR) reducers for 110 mm bore pipe larger bore measured complete all as specified and as directed.

Supply and fixing in repair PVC (SWR) 110 mm bore 'P' traps complete all as specified and as directed.

Supply and fixing in repair stack clamp out of 50mm x 5mm flat iron stays including bolt and nuts and securing ends of stays to walls or roof for 75 mm bore piece complete all as specified and as directed.

Supply and fixing in repair stack clamp out of 50mm x 5mm flat iron stays including bolt and nuts and securing ends of stays to walls or roof for 100 mm bore piece complete all as specified and as directed.

Taking down cement or cement lime plaster/ terrazo finish of any description from brick or stone walls including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed by Engineer-in-Charge.

Material and labour for rendering 5 mm thick in cement and sand mortar (1:3) on cement concrete surfaces as on ceiling including finishing the surface even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge. Note: - Contractor shall have no claim on if plaster is carried out in patches irrespective of any height.

Material and labour for rendering 15mm thick on fair faces of brick or concrete surfaces in cement mortar (1:6) finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge. Note: - Contractor shall have no claim on if plaster is carried out in patches irrespective of any height.

Material and labour for rendering 15 mm thick cement plaster on concrete solid block/ brick walls in two coats, first coat of 10 mm in cement mortar (1:4) and second coat of 5mm in cement mortar (1:4) mixed with liquid water proofing compound finished in even and smooth without using extra cement complete all as specified and as directed. Note: - Liquid water proofing compound will be measured and paid separately.

Supply only liquid integral water proofing compound ISI marked complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of newly plastered surfaces of ceiling and applying three coats of white wash complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of newly plastered surfaces of ceiling and applying two coats of oil bound distemper complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of newly plastered surfaces of wall including cornices, pillasters etc and applying two coats of cement based paint, white or tinted over a coat of alkali resistant priming paint complete all as specified and as directed.

Material and labour for applying two coats of oil bond distemper over a coat of wall care putty on walls after preparation of newly plastered surfaces complete all as specified and as directed.

Material and labour for complete removal of existing treatment of wall including cornices, pillasters etc by scrapping down and applying two coats of cement based paint, white or tinted complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of old surfaces by complete removal of existing treatment of walls including pillars etc. by mechanical equipment like electric wall sander and applying two coats of oil bound distemper using rollers over a coat of primer including two coats/ layer of wall care putty complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparation to old decorated, plastered or unplastered surfaces of ceiling, by brooming down, scrapping down smoke spots, moulds, moss and efflorescent salts etc. and applying two coats of white (lime) wash including cornices pillasters etc complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) complete all as specified and as directed.

Material and labour for 25 mm thick PCC (1:2:4) type B-0 (using 12.5mm graded crushed stone aggregate) including finishing the surface of concrete topping even and fair without using extra cement complete all as specified and as directed by Engineer-in-Charge.

Material and labour for 75 mm thick cement concrete (1:3:6) type C-2 (using 40 mm graded crushed stone aggregate) in plinth protections/ hardstanding, finished even and smooth without using extra cement complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing, removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

Material and labour for coloured non-skid ceramic tiles 600 x 600 x 7 to 10 mm thick fixed on floors with approved tile adhesive and provided with 4mm spacer, spacer gaps to be filled with approved epoxy grout complete all as specified and as directed by Engineer-in-Charge. Note: - Epoxy grout should be filled to a depth equal to half the thickness of tiles.

Material and labour for Glazed ceramic coloured tiles in vertical surfaces 600 x 300 x 7 to 10 mm thick, fixed on walls with approved tile adhesive and provided with 4mm spacer, spacer gaps to be filled with approved epoxy grout complete all as specified and as directed by Engineer-in-Charge. Note: - The ends of corner tiles at all horizontal and vertical joints shall be mitred/ provided with PVC corner strips whichever found aesthetic and approved by GE at ground, to match the edges properly. There should not be any voids behind any tiles. The epoxy grout to be filled to a depth equal to half the thickness of tiles. The rates quoted shall be deemed to be all inclusive.

Material and labour for 20 mm thick granite black (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills cooking platforms and like including pointing into white cement (1:2) using marble dust with admixture of pigment to match shade of granite laid over and including screed bed or bedding layer of mortar 15mm thick for laying floor in cement mortar (1:4) finished even and rough to receive top layer complete all as specified and as directed.

Material and labour for machine cut kota stone slab flooring not less than 19mm thick (size of stone shall not less than 55cm x 55cm), 75mm wide white marble border allround, laid over and including 20 mm thick screed base in cement mortar (1:6), jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, grinding and polishing to yield mirror finish with machine complete all as specified and as directed.

Dismantling of stone slabs and tiles of any description or thickness in floors/ dado etc laid bedded and pointed in any mortar complete all as specified and as directed.

Material and labour for granite 18-20 mm thick (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and as directed.

Material and labour for 25 mm thick (average thickness) PCC (1:2:4), type B-0 (using 12.5mm graded crushed stone aggregates) as in floor by maintaining required gradient/ undulation, finished even and fair as in roof padding including preparation of surface and mix with water proofing compound and finished even and fair without using extra cement complete all as specified and as directed. Note: - WPC will measured and paid separately as supply only.

Complete removal of the existing roof treatment any no's of layers taken out membrane, PCC padding/ roof, tiles etc including grabbing up of tree roots, roughening and preparation of surfaces of old concrete floor by picking, scrubbing down with steel brushes, sweeping, cleaning and washing down with water to remove dust etc. and applying the following roof treatment complete all as specified and as directed. (a) Applying 1st course of 15 mm thick screed bed with cement mortar (1:4) over old concrete surface. (b) Applying 2nd course of bituminous primer @ 0.4 kg/Square Metre conforming to IS-3384 over screed bed. (c) Applying 3rd course of a coat of bonding material with blown type bitumen of grade 85/25 heating to working temperature of 180 centigrade and applied @ 1.2 kg/Square Metre. (d) Applying 4th course of APP (Atactic Polypropylene) modified polymeric 3mm thick, weight not less than 3.6 kg/Square Metre with 160 Grams/Square Metre non woven polyester made at center core reinforced laid with 75 mm side overlap and 100 mm overlap. The membrane shall be laid with LPG torch and overlap sealed and finished neat. (e) Applying 5th course of a coat of bonding material with blown type bitumen of grade 85/25 heating to a working temperature of 180 centigrade and applied @ 1.2 kg/Square Metre. (f) Applying a coat of bituminous based aluminium paint as finishing coat.

Supply and fixing in repair sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and as directed.

Supply and fixing 225 x 225mm dia glass shelf chromium plated bars including taking down old one complete all as specified and as directed. Make: - Jaquar Cat Part No AQN 771 or equivalent of makes as specified in Group - 1 of Appx 'F'.

Supply and fixing in repair glass corner of size 300mm x 300mm with 5.5 mm thick glass and stainless steel clip and stainless steel railing all round the shelf double storey complete all as specified and as directed by Engineer-in-Charge.

Supply and fixing acrylic corner shelf 225 mm including taking down old one complete all as specified and as directed.

Supply and fixing in repair chromium plated health faucet fixed type suitable for EWC's with 1.5 mtr stainless steel tube complete all as specified and as directed.

Supply and fixing in repair 15mm bore chromium plated hand shower (health faucet) 1 m flexible tube with wall hook complete all as specified and as directed by Engineer-in-Charge.

Demolition of brick work, built in cement mortar including all quoins, arches, pillars etc complete all as specified and as directed.

Material and labour for brickwork with fly ash bricks straight or curved on plan exceeding 6 m mean radius built in cement mortar (1:6) complete all as specified and as directed.

Material and labour for treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar (1:2) (1 cement : 2 coarse sand) to match the existing floors complete all as specified and as directed.

Material and labour for ATT along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and as directed.

Supply and fixing RO connection tap of brass/ chromium plated body for 15mm dia pipe including fittings with RO and make functional complete all as specified and as directed.

Dismantling of fibre glass reinforced translucent corrugated sheeting in roof covering sun shed or rain shed etc. complete all as specified and as directed.

Supply and fixing fibre glass reinforced translucent corrugated sheeting with two corrugation side laps fixed with 'L' or 'J' type hooks complete all as specified and as directed.

Supply and fixing 30mm width of flaps (when open) continuous (piano) hinges mild steel bright finish or electro galvanised complete all as specified and as directed.

Supply and fixing in repair 18mm thick factory made 100% solid WPC flush shutter (for cupboard and vanity etc) made from co-extruded three layer rigid foam sheet (Single extruded) with 0.8 to 1mm thick outer layer having density not less than 1400 kg/cum and density of central core not less than 600 Kg/cum, manufacturer by an ISO 9001/2015 certified company complete all as specified and as directed.

Supply and fixing in repairs vitreous china white wash down water closet pan single piece including fixing bolts, flushing cistern, soft close seat cover and flush pipe with 'P' trap, connecting pipe complete all as specified and as directed. Make: - Jaquar Cat Part No LYS-WHT-38751P180UFSM or equivalent in makes of Group - 1 as specified in Appx 'F'.

E/M Portion: - Taking down old unserviceable copper/ aluminium point wiring concealed/ batten (light, fan, socket or power) complete, including fixtures and fittings such as switches, sockets, ceiling roses, bell push, bell electric, lamp holder, bulk head fitting, pendants, regulators, sockets, light fitting and any type of switch board wooden/ iron, round block etc removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors, etc complete all as specified and as directed.

Material and labour for point wiring for one light/ fan/ call bell point controlled by one 5 Amp switch with 1.5 Sqmm two single core multistranded copper conductor FRLS, PVC insulated (unsheathed) heavy duty cable including continuous earth wire of size 1.5 Sqmm copper conductor multistranded FRLS, PVC insulated (unsheathed) drawn into existing concealed PVC rigid/ 1.8mm wall thickness ISI marked including pressed steel modular metal flush boxes with suitable white cover plate with frame of any way i.e. (1 to 12 way as per site requirement) for mounting modular switches, sockets, fan regulators etc complete all as specified and as directed. Notes: - (a) Wiring shall be done by using proper colour coding including making disturbed surface good. (b) Earth wire shall be of green colour. (c) On RCC roof/ ceiling PVC conduit shall be provided on surface with proper fixing clamps all as directed by Engineer-in-Charge.

Description all as per Ser item No 170.00 here-in-before but 5 Amp socket outlet on same board complete all as specified and as directed.

Description all as per Ser item No 170.00 here-in-before but socket outlet 5 Amps independent board complete all as specified and as directed by Engineer-in-Charge.

Description all as per Ser item No 170.00 here-in-before but for one 6 pin socket outlet 15 Amps on independent board with cables 2.5 Sqmm size complete all as specified and as directed.

Supply and fixing of modular switch 1 way 6 A, 1 module, 240 volts ISI marked complete all as specified and as directed.

Supply and fixing of modular switch 1 way 16 A, 1 module, 240 volts ISI marked complete all as specified and as directed.

Supply and fixing of modular socket, 6A - 2/3 pin combined 2 module, 240 volts ISI marked complete all as specified and as directed.

Supply and fixing of modular socket 6A/16A - 2/3 pin combined 2 module, 240 volts ISI marked complete all as specified and as directed.

Supply and fixing of fan step regulator, 120W 1 module, 240 volts ISI marked complete all as specified and as directed.

Material and labour for distribution board sheet steel powder coated for MCB with copper bus bar and neutral link earthing stud SPN 8 way 240 volts double door complete all as specified and as directed by Engineer-in-Charge. Note: - Distribution board and MCB's should be of same make.

Supply and fixing in replacement of 5 to 32 Amp MCB 240 V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles in the MCB distribution board complete with connection, testing and commissioning complete all as specified and as directed.

Supply and fixing in replacement MCB 40 Amp 240 V, 10 KA 'B' curve in the MCB distribution board complete with connection, testing and commissioning complete all as specified and as directed.

Supply and fixing of SPN 32 Amp rating 240 V, 10 KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB distribution board complete with connection, testing and commissioning complete all as specified and as directed.

Supply and fixing MCB SPN 40 to 63 Amp rating 240 V, 10 KA 'B' curve in the MCB distribution board complete with connection, testing and commissioning complete all as specified and as directed.

Supply and fixing MCB TPN 40 to 125 Amp in the distribution board complete with connection, testing and commissioning complete all as specified and as directed.

Supply and fixing switch piano, flush type single pole one way 5 Amp, 240 volts complete all as specified and as directed.

Supply and fixing of switch piano, flush type single pole one way 15 Amps, 240 volts complete all as specified and as directed.

Supply and fixing socket outlet 2 in 1, 3 pin, 5 A complete all as specified and as directed.

Supply and fixing of socket outlet 5 pin, 15 Amp, flush type, 240 Volts, 6 pin flush type complete all as specified and as directed.

Supply and fixing of switch socket outlet combined 5 pin 5 amp flush type, 240 volts complete all as specified and as directed.

Supply and fixing switch socket outlet combined 2 in 1, 3 pin 5 amp and 15 amp flush type, 240 volts complete all as specified and as directed.

Supply and fixing for bell push, flush type single pole, 5 Amp, 240 volts complete all as specified and as directed.

Supply and fixing ceiling rose 3 terminal surface type complete all as specified and as directed.

Material and labour for lamp holder, PVC/ Polycarbonate type with back plate suitable for batten fittings complete all as specified and as directed.

Material and labour for self ballast LED retrofit lamp with PVC body and PC Diffuser 9 watt 230 Volt 6500K complete all as specified and as directed.

Supply and fixing of LED lights fitting 1 x 20 W, 220 V, AC decorative box type complete with LED tube rod 20 watts driver, holder and power factor >0.95, 100 Lumen/Watt, 6500 K cool day type conforming to ISI including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete (4' ft long) with LED rod 20 watt, 230 Volts 50 Hz complete all as specified and as directed.

Supply and fixing of LED light fitting mirror type with high output diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

Supply and fixing of call bell Ding Dong AC 230 Volts, single pole complete all as specified and as directed.

Material and labour in replacement sub main wiring with proper colour coding, insulated, unsheathed, multistranded, copper conductor FRLS, cable of 2 run 6 Sqmm for phase and neutral and one run of 6.0 Sqmm for earth wire unsheathed, multistranded, copper conductor FRLS, drawn through the existing rigid PVC concealed conduit fixed on wall. Two runs of cable for phase/ neutral and one run of cable for earth will be measured and paid as one unit length complete all as specified and as directed. Note: - Wiring shall be done in proper colour coding.

Material and labour in replacement sub main wiring with proper colour coding, insulated, unsheathed, multistranded, copper conductor FRLS, cable of 2 run 4 Sqmm for phase and neutral and one run of 4.0 Sqmm for earth wire unsheathed, multistranded, copper conductor FRLS, drawn through the existing rigid PVC concealed conduit fixed on wall. Two runs of cable for phase/ neutral and one run of cable for earth will be measured and paid as one unit length complete all as specified and as directed. Note: - Wiring shall be done in proper colour coding.

M/S RSJ BUILDER AND SUPPLIERS (BID ID -3306113)

M/S Sukhmani Construction Co. (BID ID -3305549)

M/S VED PAUL MAHAJAN (BID ID -3313285)

M/S TRIKUTA BUILDERS (BID ID -3313201)

M/S RAVINDER SINGH (BID ID -3313433)

M/S PRITHIVI RAJ AND SONS (BID ID -3306095)