PROVN OF DEFI SINGLE OFFRS ACCN AT UDHAMPUR

Amount

Sch 'A' Part-I (Building Work):-This Schedule is not Pre-Priced by MES and the Pre-Priced rate indicated as "Rs. 0.00" under col.5 signifies this fact only.

Construction of Block of Defi Single Officers Accn complete all as shown on drawings and as specified.

Construction of Block of pump house building with ramp complete and all as shown on drawings and as specified.

Construction of Semi Underground Sump of capacity 5000 gallons, complete all as shown on drawings and as specified.

Total Amount of Sch 'A' Part - II (Site Clearance)

Total Amount of Sch 'A' Part - III (Internal Water Supply)

Total Amount of Sch 'A' Part - IV (Internal Electric Supply)

Total Amount of Sch 'A' Part - V (Plumbing Work)

Total Amount of Sch 'A' Part - VI (Protective Work)

Total Amount of Sch 'A' Part - VII (Area Drainage Work)

Total Amount of Sch 'A' Part - VIII (Sewage Disposal Work)

Total Amount of Sch 'A' Part -IX (Road, Path and Culvert Work)

Total Amount of Sch 'A' Part - X (External Water Supply)

Total Amount of Sch 'A' Part - XI (External Electric Supply)

Total Amount of Sch 'A' Part - XII (Lightening Protection Work)

Total Amount of Sch 'A' Part - XIII (Fire Fightinh Work)

Total Amount of Sch 'A' Part - XIV (Compound Wall and Gate Work)

Total Amount of Sch 'A' Part - XV (Water Heater/Geyser Work)

Sch 'A' Part - XVI (Misc Items of work) Note : This Schedule is not Pre-Priced by MES and the Pre-Priced rate indicated as "Rs. 0.00" under col.5 signifies this fact only.

Construction of septic tank for 50 users (Brick construction) complete all as shown on drg No. CEUZ /TD-1585/2021 sheet -1/4 & 4/4 and as specified.

Construction of soakage well (Brick construction) 1.80m dia and 4.5m deep below inlet pipe level (depth from inlet pipe to ground level 45cm), complete all as specified and shown on drg No. CEUZ/TD-1585/2021 sheet -1/4 & 4/4.

50mm dia, foot valve, conforming to IS-4038, complete all as specified and directed.

Centrifugal monoblock pump set mounted on a common base plate and coupled directly through a set of flexible coupling with induction motor for operation AC 415 volt, 3 phase, 50Hz, water pump discharge capacity 180 LPM at 30 Mtr head, suitable RPM, including suitbale size and capacity of starter, single core copper wire of suitable size for making connection of starter to motror of length as per site requirement, PCC foundation as per manufacturer design, complete all as specified and directed.

Cutting existing water line connection 80mm/150 mm dia and making suitable size for jointing 80mm dia pipe including welding, bending and material and labour for necessary fittings of size as per site requirement etc. complete all as specified and directed

Brick masonry valve pit of size 60 cm x 60 cm x 60 cm (inetrnal dimensions) including excavation and earthwork in any type of soil, plastering all wall surfaces internally and flush pointing to brickwork externally as the work proceeds complete including angle iron 50 x 50 x 6 mm frame, MS sheet cover 3.15 mm thick with 12 mm dia handle, locking arrangement and painting withy two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer, complete all as shown on drawing as specified and directed.

Provn of MS pipe 4.8mm thick 150mm dia, flanged at both ends and cover with ends plates by nut and Bolts having openings inlet 50 mm dia butterfly valve-02 Nos, outlet 80mm dia butterfly valve-02 Nos both end of MS pipe flanged welded with respect to their size including necessary nuts, bolts washers, insertion sheet, packing & painting the pipe with synthetic enameld over a coat of red oxide primer, fixing the complete unit in the PCC pillar, using PCC 1:2:4 type-B-1, using 20mm graded crushed stone aggregate, complete all as specified and directed.

LED 35/36 watt, IP 66 LED street light luminaries on GI bracket comprising of die cast aluminium housing with weather proof gasket of lamp and driver compartment with 120 degree view angle lumen output> 100 lumen/watt, lumen maintenance > 70% at 50000 hrs, colour temp 5000-6500k, CRI> 70, THD< 15%, PF> 0.95 and LM 80 test compliance. The driver must be integrated APFC with short circuit protection, reverse polarity protection against 5 KV high surges and comply with IEC 61000-3, IEC-61547. The lumanairs must have secondary optics with perfectly matched lens for better light control including making electrical connection, complete all as specified and as directed.

Integral LED aviation light comprising of aluminium housing with polycarbonate enclosure, 302 Nos. LED are provided, complete all as specified and directed

GI bracket 40mm dia at 120 degree of length 1.5 m, complete all as specified and directed

Junction box outdoor type of size 250 mmX 250mmx150 mm of steel sheet 1.6mm thick painted with two coats of synthetic enamel paint over a coat of red oxide primer having aluminium bus bar 2 Nos of capacity 100 amps mounted on porcelain/PVC insulator suitable for connection of minimum 2 nos LT cables of size 10 sqmm 2.0 core including clamps, nuts and bolts etc, 1 No MCB SP 6 Amps, 240 Volts, rupturing capacity 10KA, 'C' curve complete all as specified and directed.

Perforated type GI cable trays of size 450mm wide x 40mm x 40mm. for supporting LT sub main cables fabricated from perforated 2mm thick MS CRCA sheet duly galvanised with expention coupler plates duly galvanised, with bolts washer and nuts. knock out hole cable connections as per approved design. including supporting steel, fish plates, fixing accessories, nut bolts, down rods, dash fastners as required complete all as specified and directed.

Hose cabinet for hose reel made of 18 SWG gauge MS sheet of size 750mm x 750mm x 280mm and door frame made of 16 SWG MS angle iron frame capable for accomodating of hose reel of size 20mm dia x 30 Mtr length complete with coupling branch pipe etc. complete all as specified and directed.

MS cabinet (approx size 750mm x 600mm x 450mm) to including fire brigade inlet connections fabricated from 16 gauge sheet with full front glass door and locking arrangement painted and mounted on masonry platform, complete all as specified and directed.

Automatic air release valve 50mm dia suitable for domestic water with 50mm gun metal stop valve, complete all as specified and directed.

Gun metal fire brigade inlet connection for connecting to external fire fighting main consisting of 2 Nos 63mm dia instantaneous type male coupling with built in check valves and 100mm dia flanged outlet complete with all accessories, complete all as specified and directed.

Light weight squeeze grip type CO2 fire extinguisher having 3 Kg capacity complete all as per IS-15683 specifications, complete all as specified and directed.

Dry powder (ABC) type fire extinguisher having 4 Kg capacity complete all as per IS-15683 specifications, complete all as specified and directed.

Fire bucket stand (for storing dry sand) having 04 Nos MS fire buckets & MS fire bucket stand (canopy type) for hanging of fire buckets complete all as per IS-2546 specifications, complete all as specified and directed.

Supply only LED bulb 9 watt suitable for fixing on lamp holder complete all as specified and directed.

20 W LED Tube (4ft) having minimum 1850 lumens with extruded engineering plastic housing, polycarbonate diffuser, G-13 polycarbonate end cover. The LED with 120 degree view angle, > 102 lumen/ watt, lumen maintenance > 70% at 50,000 hrs, colour temperature of 5000-6000, >70 colour rendering. The driver must be integral APFC and constant current type having THD <20% and power factor >0.9 with reverse polarity protection and open circuit protection with suitable batten fitting complete all as specified and directed.

MCB single pole 240 volts any rating from 5 to 32 amps, 'C' Curve, with rupturing capacity 10 KA, including providing thimble for out going cables complete all as specified and directed.

MCB SPN 240 volts any rating from 32 to 63 amps, 'C' Curve, with rupturing capacity 10 KA, including providing thimble for out going cables complete all as specified and directed.

PVC conduit, concealed type, 25mm dia having wall thickness not less than 2mm, ISI marked inclusive of all fittings such as elbows, tees, bends, reducers etc; as required fixed in chases/under floors/slab etc. complete all as specified and directed.

Metal box of size 75x75 mm on surface/ in recess with 3mm phenolic cover for mounting switch socket etc as required complete all as specified and directed.

Telephone M.S. tag box with hinged cover having locking arrangement as per telephone deptt approval and having 10 pair tag etc. as required complete all as specified and directed.

Supplying and fixing the following in the existing sheet steel box including connections etc. as required complete all as specified and directed:-

RJ 11 Telephone socket complete all as specified and directed

TV socket complete all as specified and directed

2 pair, 0.51 mm PVC insulated, PVC sheathed annealed tinned copper conductor telephone wire drawing in existing conduit complete all as specified and directed.

CP brass two way angle valve, for 15mm bore dia pipes complete all as specified and as directed.

Fancy type health foucet with 8mm dia 1mtr long flexible tube chromium plated of 15mm bore complete all as specified and directed.

Supply, Installation, Commissioning and testing of Diesel engine driven generating set of capacity 25 KVA with AMF panel complete with suitable acousatic enclosures all as per central pollution control board guide lines, 50 cycle per second with 0.8 power factor, engine as per IS-10001/10002 and alternator as per IS 13364 complete. The Engine and alternator shall be capable to take 10% over load for one hour in every 12 hours operation. The alternator of rating 25 KVA of generator set shall be directly coupled with Diesel Engine mounted on common base plate with alternator sand all specified and comprising of the following:-

(A) Diesel Engine :- Vertical V type, 4 cylinder diesel engine of min 25 KVA rated at 1500 RPM as per ISO 3046/BS-5514/649 or 10002 direct injection type with turbo charger and water cooled engine electric starting system, arrangement of starting and the engine shall be capable of running 12 hours continuously and with 10% of overloading for one hour in each 12 hours running, The engine shall be equipped with all standard fittings all as per manufacture's recommendations and with latest CPCB norms. Engine shall be directly coupled with alternator mounted on common base plate with the following:- (a) Electric Motors 12 volts with batteries as per manufacturer recommendation with battery charger and battery charger having electronic control consisting of diodes, rectifiers contacts, resistance etc. The battery charger shall be able to charge the battery at all time whenever electric supply is given to the battery charger through control panel. (b) Heavy duty industrial silencer fitted with expansion joint and silencer pipe duly lapping with asbestos rope from engine to outside power house building up to 0.50 meters and independently supported with and including frame fixed to wall/floors. (c) Fly wheel with coupling bolts. (d) Lub oil filter. (e) Instrument panel comprising of microprocessor based controller for measuring parameters like coolant temperature, running hours, lubricating oil pressure etc.

(f) Engine speed governor (Electro Mechanical) class AI, Governing as per BS 5514. (g) Air filter (Dry type). (h) Turbocharger of suitable capacity. (j) Gera pump for forced feed lubrication. (k) Fuel Injection pump. (l) Fuel filter double bowl. (m) Microprocessor based controller in panel for high cooling water temperature and lo lube oil pressure with alarm and shut down facility. (n) Radiators. (o) Flexible rubber coupling. (p) Set of fuel pipes of suitable length. (q) Base plate. (r) Fuel tank capacity as per manufacture's design with all connecting pipe and fabricated MS stand including level gauge. (s) Anti vibrating pads and mounting for the generators set, Engine and alternator. (t) Lagging of exhaust manifold with asbestos rope to exposed pipes. (u) 40mm bore flexible exhaust pipe with end flanged.

(B) Alternator :- Alternator of rating capacity 25 KVA and capable to take 10% extra load at every 12 hours interval for one hour, 3 phase, 4 wire, 50Hz, 415 volts, 0.8 power factors, 1500 RPM self excited self regulated required to be coupled with above engine. The alternators shall be conforming to IS-4722 & IS-4728 as per following specifications:- (a) Type : Salient poles, single bearing brushless type suitable for direct coupling to engine. (b) Rating : Guaranteed to deliver required output at the ambient temp conditions. Suitable for an over load of 10% for 1 hour in every 12 hours operations. (c) Voltage regulation : Provided with fast response thyristors type electronics automatic voltage regulators, which holds output voltage with in desired limits (+/- 1%) (d) Self excited - self regulated. (e) Alternator loading : suitable for taking rated load immediately after machines reaches rated voltage and speed. (f) Vibration : Suitable for direct coupling with engine and mounted on Common MS channel base frame. (g) Enclosures: Screen protected drip proof enclosure with IP- 23 degree of protection. (h) Cooling : Air cooled type with radial fan mounted on rotors. (j) Control panel shall be provided with PC 1.1 Controller and digital display for measuring of line / phase voltages / currents, frequency etc. and having MCCB of 63 Amps with overload and short circuit protection.

(C) AMF Panel :- (i) Standard control panel for DG set shall be made of fabricated sheet cubical type with front hinged cover, with internal copper wiring and of suitable size complete with microprocessor based controller with following features :- (a) State of the art compact Microprocessor based fully configurable technology. (b) Integration of all engine and alternator parameters. (c) For ease of viewing, high performance graphical LCD and prominent display. (d) Event logging history for easy of maint/service. (e) Capability of withstanding wide range of operating temp. (f) Individual touch buttons for manual, auto and test mode. (g) LED indications for genset status and alarms. (h) Battery conditions monitoring. (j) Statistical cumulative counters like, No of starts, Engine run Hrs, Kwh. (k) Setting provisions for different parameters on front panel. (l) Two Nos. Microprocessors based EDO, MCCB 63 Amps, 25 KA breaking capacity, one for main supply and other for DG set supply. (m) Two No contactors of 100 Amps capacity for main and DG. (n) Aluminium bus bars of 100 Amps capacity provided with termination.

(ii) Display Parameters :- (a) Electrical parameters : Phase voltage , line current, frequency, average voltage, average current, KW, KWH, KVA, KVAR, power factor. (b) Mechanical parameters : Lube oil pressure coolant, temp, engine speed, fuel status, engine run hours, battery voltage. (iii) Protections :- (a) Electrical protections : Under/Over voltage , under/over frequency, phase failure. Phase sequencer reverse, over current. Over KW. (b) Mechanical Protections : Under/over speed, low lube oil pressure, high engine coolant temp, low fuel level alarm, start/stop fail, charging alternator fail. (iv) Cable entry gland plate with out cable glands. (D) Connection of alternator control panel to LT panel with PVC insulated unarmoured single core copper cable of size 25 Sqmm, 1100 volts grade including copper tube terminal heavy duty at both ends for connections and 40m long.

(D) Foundations :- DG Set shall be installed on new foundations block as per manufacture recommendations including excavation works for foundations, provision of cable ducts, making good any damage to existing structure, fuel piping from fuel tank to generator set with medium grade GI tubing and cold water piping system (Medium grade GI tubing from nearest water point to radiator of engine with brass tap and stop cocks and fittings, complete connecting the existing earthing strips to control panel, DG set and generator. Note:- The size of GI tubing shall be as per literature of manufacturer or as directed by GE if not mentioned in literature of manufacturer.

(E) Testing:- Pre commissioning test shall be carried out as mentioned in tender documents. The quoted rate/amount shall be deemed to be included for this provision. Nothing extra shall be paid on this account.

Point wiring with 1.5 sqmm PVC insulated FRLSH unsheathed copper conductor single core multi strand flexible cable and 1.5 sqmm PVC insulated unsheathed copper conductor single core cable (green colour) as earth lead in, concealed type, drawing in and including PVC conduit 25 mm dia, having wall thickness not less than 2mm for one lights/fan point/bell points controlled by one switch, complete all as specified and directed.

All as per serial item No '51' above, but for one socket outlet 3 pins 5 amps controlled by one switch on independent board complete all as directed.

Point wiring with 4 sqmm PVC insulated FRLSH unsheathed copper conductor single core multi strand flexible cable and 4 sqmm PVC insulated unsheathed copper conductor single core cable (green colour) as earth lead in, concealed type,drawing in and including PVC conduit 25 mm dia, having wall thickness not less than 2mm for one lights/fan point/bell points controlled by one switch complete all as specified and directed.

Point wiring for AC, 240 volts, 20 Amp, polycarbonate industrial 3 pin (IP 65/66) socket outlet, independent, with 20 Amps double pole MCB in poly carbonate enclosure , including circuit wiring of any length from the distribution board or/ switch board etc. with two 6 sqmm. PVC insulated, stranded, flexible unsheathed, FRLSH copper conductor single core cable, concealed type, drawing in and including PVC conduit of suitable dia having wall thickness not less than 1.6mm along with one x 4 sqmm. PVC insulated, stranded, unsheathed, flexible, FRLSH copper conductor cable for loop earthing etc. as required complete all as specified.

Point wiring with 1.5 sqmm PVC insulated FRLSH unsheathed copper conductor single core multi strand flexible cable and 1.5 sqmm PVC insulated unsheathed copper conductor single core cable (green colour) as earth lead in, concealed type,drawing in and including material and labour for PVC conduit 25 mm dia with fittings, having wall thickness not less than 2mm for staircase lights controlled by two way switch, complete all as specified and directed.

Modular switch, one way 6 Amp, 240 Volts complete all as specified and as directed.

Modular switch, one way 16 Amp, 240 Volts complete all as specified and as directed.

Modular Socket, 6A 2/3 Pin combined 2 module, 230 V complete all as specified and directed.

Modular Socket, 6A/ 16A – 2/3 Pin combined 2 module, 230 V complete all as specified and directed.

Sub main wiring with two single core FRLSH PVC insulated unsheathed 1100 volts grade cable with stranded copper conductor (2 run of cable) of size 10 Sqmm drawing through and including material and labour for concealed rigid non metallic PVC conduit with fittings medium grade ISI marked 25mm dia including one single core FRLS PVC insulated unsheathed 1100 volts grade cable with stranded copper conductor of size 10 sqmm one run as earth continuity conductor connected to common earth and earth dolly, complete all as specified and directed. Note:- Three run of 10 sqmm FRLSH cable and one run of rigid non matelic PVC conduit of 25mm dia shall be considered as one unit of RM for payment purpose.

Sub main wiring with three single core FRLSH PVC insulated unsheathed 1100 volts grade cable with stranded copper conductor (3 run of cable) of size 16 Sqmm drawing through and including material and labour for concealed rigid non metallic PVC conduit with fittings medium grade ISI marked 25mm dia including one single core FRLS PVC insulated unsheathed 1100 volts grade cable with stranded copper conductor of size 16 sqmm one run as earth continuity conductor connected to common earth and earth dolly complete all as specified and directed. Note:- Three run of 16 sqmm FRLSH cable and one run of rigid non matelic PVC conduit of 25mm dia shall be considered as one unit of RM for payment purpose.

Modular switch 2 way 6A, 1 module complete all as specified.

Earthing complete with galvanised steel earth plate electrode 600mmx600mmx6mm thick buried directed in ground (earth plate not less than 2.25m deep below normal ground level) with top edge of the plate not less than 1.5m below normal ground level) connected to and including galvanised strip 25x4mm by means of bolts, nuts, check nuts and washers of galvanised iron including PCC 1:2:4 in pit, angle iron 25x25x3mm frame work with precast RCC 1:2:4 cover reinforced with 8mm dia TMT bars @ 150mm C/C both ways and 12 mm dia MS fabricated handle, medium grade GI watering pipe 20mm bore with funnel, wire mesh and light grade GI protection pipe 40mm bore upto 7.5m length for drawing in earth lead wire, salt, charcoal, etc. Including excavation and earth work in any type of soil, removal of surplus soil to a distance not exc. 50m complete all as shown in electrical plate No 3 of MES schedule 2009 (Pt-I) and connected to main control board all as specified or indicated including testing on completion, complete all as specified and as directed.

Earthing complete with galvanised steel earth plate electrode 600mmx600mmx6mm thick buried directed in ground (earth plate not less than 2.25m deep below normal ground level) with top edge of the plate not less than 1.5m below normal ground level) connected to and including galvanised strip 32x6mm by means of bolts, nuts, check nuts and washers of galvanised iron including PCC 1:2:4 in pit, angle iron 25x25x3mm frame work with precast RCC 1:2:4 cover reinforced with 8mm dia TMT bars @ 150mm C/C both ways and 12 mm dia MS fabricated handle, medium grade GI watering pipe 20mm bore with funnel, wire mesh and light grade GI protection pipe 40mm bore upto 7.5m length for drawing in earth lead wire, salt, charcoal, etc. Including excavation and earth work in any type of soil, removal of surplus soil to a distance not exc. 50m complete all as shown in electrical plate No 3 of MES schedule 2009 (Pt-I) and connected to main control board all as specified or indicated including testing on completion, complete all as specified and as directed.

Earthling complete with galvanized steel earth plate electrode 600x600x6mm buried directly in ground (earth pit not less than 2.25 m deep below ground level) with top edge of earth plate not less than 1.5m below normal ground level connected with galvanized iron earth lead wire 4mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel complete with 15mm dia GI light grade protection pipe, 20mm dia GI medium grade watering pipe with funnel including charcoal, dust, salt, PCC M-15 type B1 in pit with angle iron (25x25x3)mm frame work with precast RCC 1:2:4 type B-1 cover reinforced with 8mm dia TMT bars @ 150mm C/C both ways and 12mm dia MS fabricated handle, test point etc. in and including light grade GI protection pipe 15mm bore up to 5m length for drawing in earth lead wire, all as shown in electric plate No. 3 of SSR Part-I complete with necessary earth work in any type of soil, removal to a distance not exceeding 50m, testing on completion complete all as specified & directed.

Supply, Installation, testing and commissioning of 8 passengers lift, PM Gearless (Located above shaft) speed 1.5 mps, lift with single speed motor 415 volts, 3 phase, AC, 50 Hz, supply confirming to IS-14665, suitable to serve G+5 upper floors with AC Variable Voltage & Variable Frequency drive (VVVF drive) UPS supply complete with all standards accessories, simplex automatic and manual dual controlled operation with/without attendant, centre opening doors with door drive (electric motor driven mechanism) sliding stainless steel doors, automatic rescue device (ARD) systems, 3D infra red sensor in full height of door & built in announcing systems without hand set (04 Nos, one each in car, Machine room & near Ground Floor landing door) complete all as specified and directed as under:-

ELEVATORS :- (i) Type and capacity of lift 08 passangers - 544 Kgs. (ii) Speed 1.5 m/sec with single speed motor. (iii) Type of drive - AC Variable Voltage and Variable Frequency. (iv) Machine Room - Located above the hoist way. (v) Travel - 28.8 Metres (Approx). (vi) Serving - Ground to 8th floor (Floor designation will be 0,1....). (vii) Nos of stop - 6 (viii) Hoist way dimensions 1900mm(w) x 1900mm (D). (ix) Power Supply - 415 Volts, 3 phase, AC, 50 Hz. (x) Auxiliary - AC, single phase, 220 volt, 50 Hz. (xi) Car Size (inside) - 1300mm (L) x 1100mm (W) x 2200mm (H). (xii) Pit depth - 1600mm. (xiii) Head room - 4200mm. (xiv) Car Enclosure - Car ceiling & panel - SS hairline finish, panelling of standard thickness with adequate LED lighting on ceiling covered with translucent acrylic cover fitted with powder coated aluminium frame and concealed fan(CT002) with powder coated aluminium grill.

(xv) Car flooring - Aluminium chequered palte flooring, car illumination : LED lights. (xvi) Nos of entrance - Front opening in all landings. (xvii) Car Entrance - Centre opening, power doors in stainless steel hairline finish. (xviii) Door safety - Full height infra red curtain. (xix) Landing Entrance - Centre opening power doors in stainless steel hairline finish for car and landing at all floors. (xx) Clear opening - 800mm (w) x 2000mm (h). (xxi) Controls - Full colective simplex. (xxii) Indicators. (a) Car COP - Panel height with seven segment red indicator and round surface mounted buttons. (b) Landings - Seven segment Red indicator and round surface mounted buttons. FEATURES:- (a) Direction and position indicators in car. (b) Emergency alarm. (c) Facia Plate. (d) 2 phase fireman drive. (e) Two way hands free press & speak intercom. (f) Full height infra red safety curtains with criss cross beams.

(g) Pit ladder. (h) Emergency light rechareable battery. (i) Adjustable guide shoes. (j) Micro movement LED based buttons. (k) +10% to -10% voltage fluction with stand capacity. (l) Mirror on rear side (half height). (m) Over speed governer. (n) Load weighing device. (o) Automatic phase reversal. (p) Mannual rescue operation. (q) Pressure limiter in doors. (r) Car door lock. (s) Automatic rescue device/Automatic landing device to be operated with maintenance free landings as specified . Note :- The lift shall be installed by the Enginners of the Manufacturer only. The testing of the lifts shall be carried out by the manufacturer in the presence of the rep of accepting officer and through the authorised agency of the State Govt.

LED decorative wall mounting light fitting brushed nickel finish fixture with airily diffuser and making all connection using flexible copper cable of suitable size complete all as specified and directed.

Chandra Construction (BID ID -3257523)

vijay builders (BID ID -3258828)

SHIVAE CONSTRUCTION (BID ID -3262893)