MMNPPNA_23_24_62 Improvement of Borpatra Ali as Gaurab Path under Mukhya Mantrir Nagariya Pakipath Nirman Achani (MMNPPNA) for the year 2023-24, Jorhat MB

Amount

5.2(ii) Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous/granular surface cleaned with mechanical broom. (Including cost of testing of materials at site and laboratory as directed by the deptt.) (b) dry & hungry bituminous surface (III) With Bitumen emulsion CRS-1

17.3 Bituminous Concrete Providing and laying semi dense bituminous concrete with 100-120 TPH batch type HMP producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 to 5 % of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MoRT&H specification clause No. 508 complete in all respects) (including carriage up to initial lead of 5.0 km from quarry and carriage of mixed materials up to 10.0 Km initial lead from mixing plant) (Including cost of testing of materials at site and laboratory as directed by the deptt.) A (a) With hydrated lime / cement as filler ( refer table 500-9 of MoSRT&H specification), (I)'with 60/70 or VG-30 grade bitumen, (ii) for Grading-II ( 13 mm nominal size )

17.10 I/A/Plain/Reinforced cement concrete, in open foundation complete as per drawing and technical specification including steel shuttering formwork. PCC Grade M30.(ii) Using Batching Plant, Transit Mixer and Concrete Pumpr

16.38 Providing and laying of hot applied thermoplastic compound 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, thickness of 2.5 mm is exclusive of surface applied glass beads as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes and conforming to the MoSrt&H specifications Road Marker (Edge Line), Road Marker (Center Line)

10.80 Painting Lines, Dashes, Arrows etc on Roads in Two Coats on New Work (Painting lines, dashes, arrows etc on roads in two coats on new work with ready mixed road marking paint conforming to IS:164 on bituminous surface, including cleaning the surface of all dirts, dusts and other foreign matter, demarcation at site and traffic control.)

10.20 A (I) Retro reflectorised Traffic sign: Providing and erecting of Retro-Reflectrorised cautionary, mandatory & informatory sign as per IRC: 67 made of high intensity encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick fixed on an angle iron of 25x25x4mm supported on a mild steel angle iron post 75mm x 75mm x 6mm firmly fixed to the ground by means of properly design foundation with M-15 grade Cement concrete 45cm x 45cm x 60cm, 60cm below ground level as per approved drawing and sign. ( All the Steel work must be Tata/Sail/or any other approved brand) (i) 90cm equilateral traingle

10.20 A (I) Retro reflectorised Traffic sign: Providing and erecting of Retro-Reflectrorised cautionary, mandatory & informatory sign as per IRC: 67 made of high intensity encapsulated lens type reflective sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick fixed on an angle iron of 25x25x4mm supported on a mild steel angle iron post 75mm x 75mm x 6mm firmly fixed to the ground by means of properly design foundation with M-15 grade Cement concrete 45cm x 45cm x 60cm, 60cm below ground level as per approved drawing and sign. ( All the Steel work must be Tata/Sail/or any other approved brand)(iii) 90cm circular

10.3(A)/I Direction and place identification sign more than 0.9sqm size board. Providing and erecting direction and place identification retro-Reflectrorised sign as per IRC:67 made of encapsulated lens type reflective sheeting vide clause 801.3 fixed over aluminium sheeting, 2mm thick with area exceeding 0.9sqm fixed on an angle iron of 25x25x4mm supported on a mild steel angle iron post 75mm x 75mm x 6mm, 2 nos. firmly fixed to the ground by means of properly design foundation with M-15 grade Cement concrete 45cm x 45cm x 60cm, 60cm below ground level as per approved drawing and sign. . ( All the Steel work must be Tata/Sail/or any other approved brand)

10.20 Road Markers/Road Stud with Lens Reflector Providing and fixing of road stud 100 x 100 mm die cast in aluminium, resistant to corrosive effect of salt and grit, fitted with lense reflectors, installed in concrete or asphaltic surface by drilling holes 30 mm upto a depth of 600 mm and bedded in a suitable bituminous grout or epoxy mortar, all as per BS:873 (Part 4) 1973.

Demolishing brick work manually/by mechanical means including stacking of serviceable materials and disposal of unserviceable materials within 50 meters lead as per direction of Engineer-in-charge.

Demolishing R.C.C work manually/by mechanical means including stacking of steel bars and disposal of unserviceable materials within 50 metres lead as per direction of Engineer-in-charge

Earthwork in excavation by mechanical means (Hydraulica excavator)/manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10sqm on plan) including geeting out and disposal of excavated earth lead upto 50m and lift upto 1.5m, as directed by Engineer-in-charge All kinds of soil

Brick on edge flooring with bricks of class designation 7.5 on a bed of 12mm ceent morter, including filling the joints with same morter, with commom burnt clay non modular bricks: 1:6(1cement : 6 coarse sand)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering-All work up to plinth level: 1:3:6(1cement:3coarse sand(zone-III) derived from natural sourse:6 graded stone aggregate 20mm nominal size derived from natural sources)

Brick with common burnt clay F.P.S (non modular) bricks of class designation 7.5 in foundation and plinth in: Cemnt mortar 1:6(1 cement:6 coarse sand)

Half Brick with common burnt clay F.P.S (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V levelcement mortar 1:4 (1 cement:4 coarse sand)

Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Mild steel and medium Tensile Steel bars

Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Mild steel and medium Tensile Steel bars

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement-All work up to plinth level: 1:1.5:3(1 cement: 3 graded stone aggregate 20mm nominal size derived from natural sources)

Reinforced cement concrete work in walls (any thickness), including attached plaster, butresses, plinth and string courses, fillet, columns, pillars, piers, abutments, post and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement: 1:1.5:3 (1cement: 1.5 coarse sand (zone-III) derived from natural sourse : 3 graded stone aggregate 20mm nominal size derived from natural sources)

15mm cement plaster on the rough side of single or half brick wall of mix: 1:6 (1 cemeny" 6 fine sand)

Fishing walls with water proffing cement paint of required shade: New work (Two or more coats applied @3.84 kg/10sqm)

Centering and shuttering including strutting, propping etc. and removal of forms for Foundation, footing, base of columns etc for mass concrete ,Footing Rectengular,Column

Centering and shuttering including strutting, propping etc. and removal of forms for Foundation, footing, base of columns etc for mass concrete,Lintels,Beams,Plinth Beams,Girders,etc.Columns,Pillars,Piers,Abutment,Posts and Struts

Centering and shuttering including strutting, propping etc. and removal of forms for Foundation, footing, base of columns etc for mass concrete(Columns,Pillars,Piers,Abutment,Posts and Struts )

Providing/Painting Mural with cement morter with paint as per design and directed by Engineer-in-charge

ILLUMINATION WORK :Supplying and Installation of antique design steel light for Gaurab path through both sides of the road with underground cabling

M/S. M.P. AGARWALLA