ADDN/ ALTN/ IMPROVEMENT OF TOILET BLOCK OF CERTAIN OTM ACCN AT AF STN BHISIANA

Amount

B/R WORKS

Demolition of concrete above ground floor for sunken portion exc 15 cm thick and removing the rubbish out side MD land complete all as specified.

M&L for 15 mm thick rendering in cement mortar (1:3) as in sunken portion mixed with water proofing compound 3% by weight of cement, finishing surfaces even & smooth without using extra cement complete all as specified and as directed. Note :- Water proofing compound shall be Measured and Paid Seperately

Supplying only integral water proofing compound, ISI marked complete all as specified and as directed.

M&L for Bitumen blown any grade, applied hot, two coats to concrete surfaces at the rate of 1.5 Kg per Sqm per coat complete all as specified.

Polythene film, 50 micron thick, laid on a coat of bitumen primer, @ 0.30 to 0.50 kg per sqm in sunken area complete all as specified and directed by Engineer In Charge.

M&L for PCC (1:5:10) type E-2 using 40mm graded stone aggregate as in filling of sunken and mass concrete complete all as specified and as directed.

M&L for 50mm dia GI spout pipe fixed in sunken floors by means of cutting holes in wall bedded in cement mortar and making good the disturbed portion of wall complete all as specified and directed.

Taking down cement plaster on brick or stone masonry Including raking out joints, hacking for key scrubbing down with water etc including removing from site complete all as specified and as directed.

M&L for 15 mm thick plaster in 1:4 cement mortar and finishing the surface even and fair without using extra cement including applying two coat of cement base paint over and a coat of primer after preparation of new plastered surfaces.

M&L for 15mm thick cement plaster in CM (1:6) on fair faces of brick or concrete surfaces and finishing the surface even and fair (without using extra cement) etc including applying three coats white wash and after preparation of plastered surfaces complete all as specified and directed.

M&L for 5 mm thick cement plaster 1:3 on fair faces of brick work or concrete surfaces in ceiling and finishing the surface even and fair (without using extra cement) etc including applying three coats of white wash and after preparation of plastered surfaces complete all as specified and directed.

Applying a coat of white wash over and after preparation of existing old decorated plastered/unplastered surfaces of walls, pillars, cornices by brooming down etc complete all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing up), and rubbish off the premises complete all as specified.

M&L for Non Skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors etc. including 15mm thick screed bed in CM (1:6) set and jointed in neat cement slurry and pointed in white or coloured cement to match copmplete all as specified and directed. NOTE : Cost of Cement Screed Bed shall deem to be include in the Quoted Unit Rate.

M&L for Glazed ceramic coloured tiles in vertical surface 350x250x7mm / 450x300x7mm thick including 10mm thick cement plaster in CM 1:4 set and jointed in neat cement slurry and pointed in white or colour cement to match complete all as specified and directed. NOTE : Cost of Cement Screed Bed shall deem to be include in the Quoted Unit Rate.

M&L for 25mm thick Cement concrete type B-1, 1:2:4 (20mm graded aggregate) as in sub base complete all as specified and directed.

Dismantling Stone slabs and tiles of any description or thickness laid bedded & pointed in any mortar in floors/walls, aprons including removing from site complete all as specified and directed by Engineerin Charge.

M&L for fixing of granite 18-20mm thick of any type ( table rubbed and polished in steps, jambs pillars, window cill, cooking platform and like in cement mortar 1:4 incl pointing in white cement complete all as specified and directed by Engineer in Charge.

M&L Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store

Refixing 15 mm bore old steel tubing and connections in new or old position (walls, ceiling, floors, etc.) incl new GI fiitings as required.

M&L for 15 mm dia tubes medium grade galvanised with all fitting and fixed to walls and ceilings or laid in floors complete all as specified.

Taking up or down 20 mm bore steel tubing and connections, including cleaning for refixing or removal to store

Refixing 20 mm bore old steel tubing and connections in new or old position (walls, ceiling, floors, etc.)

M&L for 20 mm dia tubes, medium grade, galvanised with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed by Engineer-in-charge.

M&L Taking up or down 25 mm bore steel tubing and connections, including cleaning for refixing or removal to store

Refixing 25 mm bore old steel tubing and connections in new or old position (walls, ceiling, floors, etc.)

Material and labour 25 mm dia tubes medium grade galvanised with all fitting and fixed complete to walls and ceilings or laid in floors

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth in brick wall complete all as specified.

Dismantling water tanks exc 500 ltr and not exc 1000 ltr and removing to store complete all as specified and directed.

S&F for Rotational moulded polyethylene water storage tanks triple layer 1000 ltr capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified and directed.

S&F Gun metal gate valves 20mm dia with iron wheel head screwed both ends for iron pipe complete al as specified and directed.

S&F Ball valves 20mm high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed complete all as specified and as directed.

S&F in repair Vitreous china squatting pan , 'Orissa' pattern, size 580 x 440 mm white, with integral foot rests complete including provision of lime concrete bedding and fixing PVC (SWR) 'P’ trap complete all as specified and as directed.

S&F in repair china wash down water closet padestal pattern white excluding flush and fix to position, including seat cover and connection to drain etc all as specified as directed.

S & F in repair vitreous china wash hand basin white, oval type counter top of size 550mmx400mm fixed on and including cast iron cantilever bracket, 32mm dia brass waste coupling and 32 mm dia PVC waste pipe, waste fitting etc. complete all as specified and directed by Engineer in Charge.

S&F in repair Vitreous China Urinal, full stall type, white (excluding flushing cistern, flush pipe and waste pipe) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing flush pipe, grating and Union for discharge pipe complete all as specified and directed by Engineer in Charge.

S&F in repairs CP Urinal spreader fixing with 15 mm dia pipe for urinal complete all as specified & directed.

S&F 32 mm Waste fittings/coupling, brass, chromium plated for sinks, basins, etc. with long screwed shanks and fly-nuts complete all as specified and directed by Engineer in Charge.

S&F PVC (SWR) floor trap (Medium duty), plain with SS grating with hole/without hole including jointed with solvent cement of 75 mm outlet dia complete all as specified and directed.

S&F PVC (SWR) floor trap (Medium duty), plain with SS grating without hole including jointed with solvent cement of 110 mm outlet dia complete all as specified and directed.

S&F in repairs flush pipe of Polyethylene of low or high density or PVC 32 mm dia, for low level cistern complete.

S&F in repairs PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed.

S&F in repair 15mm dia brass chromium plated centre hole wash hand basin with accessories in wash basin for mixing hot and cold water, screwed down for 15 mm dia bore GI Pipe complete all as specified and directed.

S&F in repair 15 mm bore Angle cock, cast copper alloy, fancy type chromium plated screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed.

S&F 15 mm bore 2 way Angle cock, cast copper alloy, fancy type chromium plated screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed.

S&F in repairs 15 mm bore Stop Valve chromium plated with long shank and cup (concealed type) ,cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union and fixed in repairs complete all as specified and directed by Engineer in Charge.

S&F CP Health Faucet with 1.20 mtr metalic expandable tube & hook complete all as specified and directed by Engineer in Charge.

S&F CP Hands free Jet spray flat nozzle with 1.0 mtr metalic including holder complete all as specified and directed by Engineer in Charge.

S&F in repar PVC connections 15 mm size with PTMT nuts of length 450mm complete all as specified and directed by Engineer in Charge.

S&F in repairs CP Tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed by Engineer in Charge.

S &F in repairs 15mm dia Bib taps, Chromium plated, screwed down, screwed for iron pipe or for brass ferrule and fixedcomplete all as specified and directed by Engineer in Charge.

S&F in repairs Chromium plated shower rose 125 mm size with or without swivel joints,including fixing to steel pipe or union complete all as specified and directed by Engineer in Charge.

S&F SS Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed by Engineer in Charge.

Demolition of cement concrete in ground floors and paving n exc 15 cm thickness (below or above ground level) incl removal of debries complete all as specified and directed by Engineer in Charge.

M&L for 75mm thick PCC (1:3:6) type C-2 using 40mm graded stone aggregate as in plinth protection complete all as specified and as directed.

Demolition of brick or stone boulder masnory, built in cement mortar including all quoins, arches, pillars, etc., but excluding ashlar facing, dressed stonework and percast concrete articles complete all as specified and directed by Engineer in Charge.

M&L for Brick work with subclass B bricks, staright or curved on plan exc 6.00 mtr mean redius, built in cement mortar (1:6) complete all as specified and as directed.

M&L for Brick work with subclass ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in 1:4 cement mortar complete all as specified and directed by Engineer in Charge.

S&F in repairs 110 mm bore PVC (SWR) pipes (Medium duty) single socketed in any length with rubber ring joints fixed to walls/floor with and including clamps, nut bolts including dismantling of old outlet pipe etc.

S&F in repairs 75 mm bore PVC (SWR) pipes (Medium duty) single socketed in any length with rubber ring joints fixed to walls/floor with and including clamps, nut bolts including dismantling of old outlet pipe etc.

S&F 110 mm bore PVC (SWR) bends any radius complete all as specified and as directed.

S&F 75 mm bore PVC (SWR) bends any radius complete all as specified and as directed.

S&F PVC (SWR) junction single Tee/'Y' junction equal or unequal 110 mm dia complete all as specified and ditected.

S&F PVC (SWR) junction single Tee/'Y' junction equal or unequal 75 mm dia complete all as specified and ditected.

S&F in repair 32 mm dia PVC waste pipe for WHB and urinal 90 cm long with union, complete all as specified and directed. equivalent).

S&F in repairs box type steel ventilator glazed & gauged factory made with side hung shutters including box type hinges with steel handle and steel peg stay,necessary grills and guard bars and 4mm thick froasted glass & wiremesh including preparation & applying two coats of Synthetic enamel paint over a coat of red oxide including taking down existing window and making good the disturbed portion with PCC or Plaster and painting the surface to match with the existing surface complete all as specified and as directed.

Taking down Chowkhats or frames with shutter not exc 1.5 Sqm each (without taking off shutters from the frames) complete all as specified and as directed.

S&F Solid PVC door frame of size 50mm x 95mm made out of 5mm plain coloured PVC sheet reinforced with MS square tube, supplying & fixing in opening as per specification and drawing complete all as specified and as directed.

S & F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm Plain colour PVC Sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as shown in SSR Part – II 2010 and as directed by Engineer-in-Charge.

100mm size stainless steel butt hinges complete all as specified and directed by Engineer in Charge.

100mm size stainless steel handles complete all as specified and directed by Engineer in Charge.

150mm long stainless steel tower bolt complete all as specified and directed by Engineer in Charge.

Taking down chowkats & shutters without taking off shutters from the frame, size of opening exc. 1.50 sqm but not exc 4 sqm each complete all as specified and directed by Engineer in Charge.

S&F Pressed steel frames for doors with one or more rebates including necessary fixing lugs,hinges, lock strike plate, etc complete all as specified and directed of size 105 X 60mm complete all as specified and directed by Engineer in Charge.

M&L for PCC (1:3:6) type C-1 using 20 mm graded agg as in back of pressed steel chowkhats etc complete all as specified and directed by Engineer in Charge.

Supply and fixing IInd class hard wood (Hollock) 35mm thick plain framed, factory made panelled shutters (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS-1003 (part – I), kiln seasoned and chemically pressure treated complete all as specified and directed by Engineer in Charge.

S&F 100mm Butt hinges medium weight, cold rolled mild steel complete all as specified and directed by Engineer in Charge.

S&F 200mm Aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and directed by Engineer in Charge.

S&F 150mm Aluminium handles, cast type anodised complete all as specified and directed by Engineer in Charge.

S&F 250 mm Mild steel Sliding door bolts plate type stove enamelled black with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts,four on bolt plate and two on staple plate and fixed complete all as specified and directed by Engineer in Charge.

M&L applying Two coats of Synthetic enamel paint over a coat of pink primer including prepration of new or previously untreated wooden surfaces of any description not otherwise described over 10 cm width or girth complete all as specified and directed by Engineer in Charge.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for reinforcement cut as required to facilitate demolition, complete all as specified and directed by Engineer in Charge.

M&L for 60 mm thick reinforced precast cement concrete 1:1:2 type B-1 (using 20mm graded stone aggregate) as in man cover bromatic slabs finish fair even and smooth without using extra cement ( Top surface will be chequred finish) including necessary form work including 2mm thick CR sheet with 2 coastly of bitumen paint and two sunk steel handle 12mm dia to surface, complete all as specified and directed.by Engr-in-charge. Note: (Reinforcement shall be measured and paid saperately)

S&F TMT MS bar 8mm dia & over, cut to length, bent to shape required, including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including MS wire ( annealed) not less than 0.9 mm dia complete all as specified and directed by Engineer in Charge.

E/M WORKS

Taking down Copper/Aluminium Point Wiring (Light, Fan, Socket or Power) including Fixture and Fittings such as Switches, Ceiling Roses, Pendants, Regulators, Sockets, Light Fittings of any description and Making Good Disturbed Surfaces of Walls, Floors, etc. so as to match with the Existing Finishes, complete all as specified and as directed.

Taking down/out unserviceable main switches and DB's including MCBs of any size / type and of any description and Making Good Disturbed Surfaces of Walls, Floors, etc. so as to match with the Existing Finishes, complete all as specified and as directed.

M&L for concelaled Point Wiring with 1.5 Sqmm (nominal area) 1100 Volt PVC insulated unsheathed FRLS multi-stranded Single Core Copper Conductor Cable with 1.5 Sqmm (nominal area) 1100 Volt PVC insulated unsheathed FRLS multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuity Wire, drawn through and including Rigid Non-metallic PVC Conduit 19mm in size, medium grade, ISI marked and its Accessories in Concealed (Partly)/ Surface (Partly) with necessary grouting of required size and depth on Wall and Making Good in Cement Mortar 1:3, providing PVC Gang Box (minimum 2.0mm thick)/Sunk Mild Steel Pressed Terminal Box (1.6mm thick) of suitable size duly painted with Red Oxide Metal Primer with 3.0mm thick Plastic Laminated Sheet Top Cover (as per Site requirement) for mounting Switches, Sockets, Fan Regulators, etc. Earth Continuity Wire connected to Common Earth dolly for ONE LIGHT/FAN POINT/ BELL POINT CONTROLLED BY ONE 1-WAY SWITCH 6 AMP, complete all as specified and as directed.

All as described above Item No 90 but Concealed point wiring 2.5 sqmm single core multi stranded copper conductor PVC insulated & unsheated cable 1100 volt grade and 1.5 sqmm PVC insulated and unsheated cable 1100 volt grade with multi stranded copper conductor for earth wire for 15/16 amp multi purpose socket combination point on the independent board complete all as specified and directed by Engineer in Charge.

M&L Switch Piano 6 Amp, Flush type, Single Pole, 1-way and , complete all as specified and as directed.

M&L Switch Piano 16 Amp, Flush type, Single Pole, 1-way, complete all as specified and as directed.

M&L Socket 16 Amp, Piano, Flush type, 2-in-1, multi-purpose, complete all as specified and as directed.

S&F Ceiling Rose, 65x17 mm Terminals, PVC Polycarbonate, Isolated body and complete all as specified and as directed.

M&L Sub-main Wiring with 2-Runs of 4.0 Sqmm (nominal area) 1100 Volt, PVC insulated unsheathed FRLSH multi-stranded Single Core Copper Conductor Cable and 1-Run of 4.0 Sqmm (nominal area) 1100 Volt, PVC insulated unsheathed FRLSH multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuty Cable along with the Wiring drawn in PVC Conduit medium grade 25mm dia including making Good Disturbed Surfaces of Walls, Floors, etc. so as to match with the Existing Finishes, complete all as specified and as directed by Engineer in Charge. Note: (a) The quoted unit rate shall include cost of PVC Conduit (b) Two Runs of Copper cable along with One Runs for earthing and one Run of PVC Conduit shall be measured as one unit.

S&F MCB DB 4-way, Single Pole & Neutral, Double Door type IP 3 , Regal Grey Colour, Sheet Steel Phosphatised, Powder Coated with 63 Amp rate Bus-bar, Neutral Link Earth Bar & Din Rail duly embedded/Concealed upto Wall surfaces including Connecting up with Existing Cable Incoming and Outgoing with Cable Lugs as per requirement and and Making Good Disturbed Surfaces of Walls/Roofs/Floors, etc. so as to Match with the Existing Finishes, complete all as specified and as directed.

S&F MCB Single Pole & Neutral, 40 to 63 Amp, 240 /415 Volt, AC, 'C' Series for fixing on MCB DB’s, 10 kA, 50 Hz , 35mm2 Terminal Capacity insulated sliding shutter including Connecting up and Fixing in DB of any make/ type, complete all as specified and as directed.

Supply and fixing 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning, complete all as specified and directed by Engineer in Charge.

M&L in repair earthing complete with galvanized steel earth plate electrode 600x600x6.3 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below normal ground level, the earth electrode surrounded by adequate quantity of charcoal dust and salt to a packed thickness of 15cm on all side and including connected to and including galvanized earth lead wire 4.0 mm dia upto 7.5 mtrs long by means of nuts and bolts, check nuts and washers of GI and connected to earhing test point and earth dolly all as shown in electrical plate No 3 of MES SSR Part-I and testing on completion including necessary excavation and earth work in any type of soil, PCC (1:3:6) type C1 chamber, pre-cast RCC slab 50mm thick in cement concrete (1:2:4), type B1, reinforced with welded steel wire fabric or XPM, (weight not less than 4 Kg per Sqm) with cast iron frame, funnel with watering pipe 20mm dia medium grade, wire mesh and lugs, GI protection pipe, 15mm dia, light grade, 7.5 mtr long for protection of earth lead upto test point etc all as specified and as directed.

Collecting Exhuast Fans of 400/450 mm sweep any type from Store yard of AGE E/M of any make/model, moving to reputed workshop as directed by GE/Engineer-in-Charge, dismantaling the same, cutting and removing the old defective/burnt out winding, cleaning the core of the fan motor, re-winding the fan motor by using machine with supper enemelled copper winding wire and using insulating materials, varnishing the assembly and re-assembling the fan including testing etc. complete all as specified and directed by Engineer-in-Charge. MAKE of winding wire : Devi Dayal/Chetak/HTP Thulax. Note: (a) All defective/unserviceable parts/items other than winding wire, varnish, insulating material, bearings, capacitors and flexible wires shall be measured separately and paid for under respective item of this schedule.

S&F in repair Exhaust fan blades (Set of three blades) suitable for 400/450 mm sweep duly painted with synthetic enameled paint fixed in replacement complete all as specified and directed.

S&F in repair Ball bearing of Exhaust fansof any sweep/size/make/ model fixed in replacement complete all as specified and directed by Engineer-in-Charge.

S&F in repair Louvers made of GI Sheet, suitable for 450 mm sweep exhaust fans fixed in replacement complete all as specified and directed.

S&F 1X18 watt incl taking down wall mounted, new generation LED T-8 Retro fit for multipurpose application with LED Rod, made from exturded aluminium housing, polycarbonate diffuser including all fixing accessories & connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed by Engr-in-Charge.

S&F Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of capacity 20 Amp, all as specified and directed by Engineer in Charge.

Supply and fix electric water heater, storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc complete all as specified and directed by Engineer in Charge.

M/s BALDEV SINGH

M/s Luxmi Constructions

M/s R.K. CONSTRUCTIONS

GUPTA AND ENGINEERS

M/S GOYAL BUILDERS

SUBHASH ARORA CONSTRUCTION CO

SIDHU CONSTRUCTIONS