SPECIAL REPAIRS TO P-89 (MT GARAGE) AT NAD TROMBAY UNDER GE (NW) MANKHURD

Amount

Taking down cement plaster on brick or stone walls, etc, including raking out joints, hacking for key, scrubbing down with water , etc complete all as specified and directed.

Dismantling of brick work /stone boulders built in cement mortar including all quins, arches, pillars etc complete all as specified and as directed.

M & L Brick work with sub class 'B' bricks straight or curved on plan exceeding 6 m mean radius built CM 1:4 complete all as specified.

M&L for Ready mix plaster 10mm thick on faces of bricks or concrete surface including necessary scaffolding upto 18m height, including preparation of wall surfaces etc complete all as specified and directed,

M&L for Ready mix plaster 15mm thick on bricks or concrete surface including dubbing coat to match with existing with necessary scaffolding upto 18m height including preparation of wall surfaces etc complete all as specified and directed,

Chipping, removing carefully loose/damaged concrete incl plastering (total thickness upto 60mm ) from RCC surfaces of columns, beams,Chajas, soffits of slabs etc by low impact Hammer/Breakar without damaging the structure & cleaning the surfaces with wire brush etc and disposal of debris out side MOD land, complete all as specified and directed. Note: Hard concrete shall not be removed by force.

M&L for cleaning existing reinforcement by sand blasting with suitable pump as directed by the GE and wire/ rotary wire brush to a shining bright finish, making the surfaces free from loose material, dirt etc complete and applying two coats of alkaline rust converting primer conforming to ASTM-B-117 of make. "Feovert" of "Krishna Conchem" OR "Roff Rust Cleaner' of 'Pidilite' OR 'Shali Rustoff' of 'STP Ltd', on rebars with time interval of 1 hr between the coats, complete all as specified and directed. (Note :- Mode of measurement: superficial area of concrete will be measured.)

M&L for Anticorrosive Treatment to Reinforcement Epoxy Zinc Primer of M/s. Dr. Fixit by application on exposed reinforcement in two coats with time interval of minimum 4 hours between each coat. The application shall be done by brush after cleaning/wire brushing to the exposed steel surfaces, complete all as specified and directed . Note:- Mode of measurement: superficial area of concrete will be measured.

M&L for providing mild steel TMT bars in various structural RCC elements like column, beams and Slab etc. including cutting, bending, fixing the bars, tying with binding wires etc. complete all as specified and directed. Note: This item is applicable for additional bars required in the existing RCC structures.

M&L for Epoxy bond coat of Make Fosroc (NITOBOND-EP) OR EPOXY BONDING AGENT of Dr. Fixit OR equivalent of M/s. Krishna Conchem as approved by GE over exposed concrete surfaces prior to application of any type of mortar to ensure bond between old concrete & new concrete by brush application complete all as specified and directed.

M&L for building up the profile of structural members by using Polymer mortar HB of Dr Fixit, while the bonding agent is still tacking upto 20mm thickness including levelling, profiling etc complete all as specified and directed.

M&L for building up the profile of structural members by using Polymer mortar HB of Dr Fixit, while the bonding agent is still tacking upto 40mm thickness including levelling, profiling etc in two layers, each layer not exceeding 20mm, complete all as specified and directed.

M&L for casting & repairing of excessively damaged distressed RCC members (exceeding 60mm in thickness) with prebatched, prepacked, single component ready to use microconcrete from Fosroc (Renderoc RG) or equivalent of Dr. Fixit as approved by GE, at any level/ height and at any lead or lift as directed including prefabricated water tight formwork, centering, scaffolding, also including mixing , laying, levelling, finishing, curing etc as per manufacturer's specifications and all other relevant worksincl scaffolding upto 18 mtr height complete all as specified and directed. (Note : Reinforcement only shall be measured and paid separately).

M&L for leakage / seepage proof coating consisting of preparing the new/old surfaces of existing exterior walls, parapet walls, chajjas etc. and applying Primeseal primer of M/s Dr Fixit or equivalent chemical of M/s STP Ltd as approved by the GE or one coat of Chemstic PDE 600 elastomeric coating (and allowing to dry for 8hrs) under torch dry condition and subsequently applying two coats of water proofing decorative elastomeric coating system Raincoat of M/s Dr Fixit with DFT 100microns or Shalicryl 215 of M/s STP Ltd or Chemstic PDE 600 elastomeric coating (the surfaces after painting one coat shall be allowed to dry for 6 to 8hours before application of next coat) including necessary scaffolding etc complete all as per manufacturer instructions and all as specified & directed. Notes: (i) The aforesaid treatment shall be got executed by the contractor from the authorised applicator of the manufacturer(s) and also necessary authenticated documents on account of above shall be submitted by the contractor to the GE. (ii) Payment for filling cracks for old surfaces shall be made for separately (iii) Payment for complete removal of existing treatment over old surfaces shall be made for

M&L for prepration of newly plaster/concrete surface of wall and applying two coat of distemper oil emulsion on walls with one coat of primer ( chalk white on plastered surfaces) and including 3mm thick putty applying complete all as specified and directed

M & L for preparing old decorated surfaces of wall (plastered or unplastered or previously white washed ) & applying one coat of white wash complete all as specified

M& L for complete removal of existing treatment on surfaces of walls and applying two coats of oil bound distemper over chalk whiting including 3 mm wall care putty one coat of primer applying on walls for smooth finish complete all as specified & directed

Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces.

M&L Preparation of old plastered or un-plastered surface of ceiling and applying one coat of oil bound distemper complete all as specified and directed.

Demolition of stone slabs and tiles laid beded and pointed in any mortar of any description or thicknes in floors , aprons etc

M&L for Light Shade Vitrified Ceramic tiles 10 mm thick (square/ rectangular) of approved size, area of each tile not exceeding 0.36 Sqm in floors etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, over and including 15mm thick cement mortar screed bed in CM 1:6 etc, complete all as specified and directed.

M&L for Light Shade 600x100x10mm thick size Vitrified Ceramic tiles, on vertical surfaces such as skirting etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, over and including 10mm thick cement mortar backing coat in CM 1:4 etc, complete as specified and directed.

M&L for coloured glazed ceramic tiles Glazed ceramic tiles invertical surface 350x 250x 6-7 mm/ 450X 300X 6-7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match as in skirting/dados including 10mm thick rendering in CM 1:4 as in backing coats of tiles finished the surfaces rough to receive tiles etc complete all as directed and specified.

M&L for Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade complete including 15 mm thick CM 1:6 screed bed for laying floor finishes all as specifed and directed..

M&L for PCC 1:3:6 type C2 (using 40mm graded stone aggregate) as in plinth protection 75mm thick, with expansion joints & top surface finished even and smooth without using extra cement etc complete all as specified and directed.

S&F in repair 18/19 mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work including dismantling if any

Demolition of lime concrete or lean concrete from sunken floor including floor tiles, hacking of surfaces after cleaning with wire brush (floor and adjoining walls) and disposing off debris outside MOD land complete all as specified and directed.

M & L for filling of lean concrete 1:5:10 type E2 (using 40 mm graded stone aggregates ) in sunken portion, as per requirement complete all as specified and directed.

M&L for PCC 1:2:4, type-B, using 20mm graded stone aggregate as in sub base of floors and for any other purpose in any location mixed with WPC @ 2% by weight of cement, complete all as specified and directed. Note: Supply only WPC will be measured and paid separately.

M & L for special treatment for sunken portion of WCs/Bath & toilet etc executed in following stages : Stage 1: Providing 15mm thick plaster in CM 1:3 mixed with water proofing chemical of Dr.Fixit or Shalicrete 'R' of STP Ltd in the proportion/quantity all as per manufacturer's instructions. State 2 : Primer-Mix Tarfelt LM of STP Ltd (diluted with water in ratio 1:1) @ 250 gms/sqm and apply the primer on the plastered surfaces. Stage 3 : Application of 1st coat of Tarfelt LM of STP Ltd (without dilution with water) @ 1Kg/Sqm by brush all as per manufactuer's instructions. Stage 4: Laying fyber glass cloth (weight not less than 50gram/ Sqm) over the 1st coat while the coated surface is still sticky. Stage 5: After 6 to 7 hours interval, apply second coat i.e. final coat of Tarfet LM of STP Ltd (without Dilution with water) @ 1kg/ Sqm by brush as per manufacturer's instructions. Stage 6: Providing 10mm thick protective plaster in CM 1:3 mixed with STP No. 1 @ 250ml/50 Kg cement all as per manufacturer's instructions. Stage 7: Carryout ponding test for 48 hours to ensure water tightness of repaired sunken portion. NOTES :(i) Mode of measurement: Actual area treated (floor and adjoining walls) will be measured and paid . (ii) The above treatment shall be got executed through applicator of manufacturer and necessary authenticated documents on account of above shall also be produced by the contractor.

Supply and fixing of 16 mm outer diameter CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings (including provision of special fittings i.e. brass elbow, brass tee, Male brass threaded adaptor, female brass threaded adaptor etc required for fixing of bib tap, stop valve with CPVC pipes) concealed in walls/ ceiling or laying in floors etc., also including cutting chases, grooves and making good the same in CM 1:3 after fixing of pipes / fittings, including taking down of old pipecomplete all as specified and directed.

Supply & fix 20mm bore GI tubing, medium grade with and including all fittings and fixed to walls and ceilings or laid in floors, including taking down of old pipecomplete all as specified and as directed.

Supply & fix 40mm bore GI tubing, medium grade with and including all fittings and fixed to walls and ceilings or laid in floors, including taking down and removal complete all as specified and as directed.

S&F in repairs PVC (SWR) floor trap, plain with grating including jointing with solvent cement 75mm dia out let including grating connecting jointing to waste pipe and taking out existing unserviceable traps by hacking out concrete joints and making good of surfaces complete all as specified and as directed .

S&F PVC connections 15mm size with PTMT nuts of length 600mm

S&F in repair towel rail 600mm long fixed with and including chromium plated brass screws and wooden/plastic cleats (Min wt 190 gms)

S&F in repairs high level/low level PVC flushing cistern with PVC flush pipe, brackets, and PVC connection complete of 10 Ltr capacity.

S&F in repairs 15mm bore Bib taps, cast copper alloy with crutch or butterfly handle, screwed down screwed for iron pipe or for brass ferrule fancy type chromium plated.

S&F in repairs 15mm bib taps two way cock, cast copper alloy with crutch or butterfly handle, screwed down screwed for iron pipe or for brass ferrule fancy type chromium plated. Make : Jaquar or Equivalent

S&F in repairs pillar taps 15 mm; of cast copper alloy with capstan; head chromium plated screwed downend with pressure with or without lettered hot or cold with long screwed shank and fly nuts, screwed for iron pipe& fixed complete all as specified

S&F in repairs stop cock 15mm cast copper alloy with crutch or butterflty handle, screwed down screwed for iron pipe or for brass chromium plated with fancy type shank and cup(concealed type)

S&F in repairs Grating doom 100mm dia of PTMT

S&F in repairs Swivel shower of PTMT any colour for fixing with 15mm pipe. (Minimum weight 40gms) ® Shower arm 15 mm size, 195mm long with bend of 45degree with flange of PTMT any colour.(Minimum weight 40gms

S&F hand shower (health Faucet) with 8mm dia 1 mtr Long flexible tube & wall hook complete all as specified .

S&F in repairs Wash basins, Vitreous China (flat back or angle back type) any size, including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe flat back, size 580x450irun (for Hospilal use) excluding taps, waste, chain and plug and porcelain stopper but including brackets

S&F in repairs Soap dish, any type, fixed to plugs with chromium plated brass screws

M&L for 35 to 40 mm thick machine cut, prepolished cuddappa stone slab as in plateform for fixing oval shape wash hand basin(including cutting the slab to oval shape to accomdate the sink and WHB), pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of stone slab etc,also including moulding/rounding to edges of the slab, including dismantling of existing tile slab complete as specified and directed.

M&L Machine cut kota stone slab flooring 20-25mm thick as in flooring, treads, risers, landing etc over 15mm thick cement screed base CM 1;6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing including dismantling of existing floor complete all as directed.

All as item above but except stone (for mirror polished only)

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations

S&F in repair 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls all complete all as specified and directed.

All as per item no. 60 above, but 75mm bore in repair

S&F in repair Vitreous china squatting pan orrisa pattern of size 580 x 440mm with integral foot rest and 'P' or 'S' trap including lime concrete bedding connecting flushing pipe and taking out old WC pan & lime concrete and unserviceable connections and making good for floor etc complete all as specified and as directed

S&F in repair Vitreous china Wash down water closet (Pedestal pattern), complete white (excluding fixing bolts, flushing cistern and flush pipe) and 'P' or 'S' trap including lime concrete bedding connecting flushing pipe and taking out old WC pan & lime concrete and unserviceable connections and making good for floor etc complete all as specified and as directed

Removing plant/growth including its roots upto 1.00m of plant height at any location/at any storey and of any description and treating the surfaces with Acid (HCL) and making good surfaces with cement mortar 1:4, complete all as specified and directed.

S&F 110mm bore PVC (SWR) bends

S &F PVC (SWR) bends, 75 mm bore,

S &F PVC (SWR) junction single(single T), 110 mm bore, equal or unequal

S &F PVC (SWR) junction single(single T), 75 mm bore, equal or unequal

S &F PVC (SWR) branch piece,double( Singe Y) 75mm bore equal or unequal

S &F PVC (SWR) branch piece,double (single Y) 110 mm bore equal or unequal

Taking down chowkats or frame with shutters ( without taking off shutters from the frame ) exceeding 1.5 Sqm but not exc 4 Sqm each including complete all as specified and directed.

Taking down chowkats or frame with shutters ( without taking off shutters from the frame ) Sqm but not exc 1.5 Sqm each including complete all as specified and directed.

S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 50 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant as per specifications drawing as directed by the Engineer - in -charge . Material test certificate and authentication should be compulsory provided by the manufacturing company.and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F stainless steel wire cloth 0.36mm mm nominal dial of wire and average width or aperature 1.40mm for fixing to wooden door/ window shutters in any position with new beads/ steel section as required for securing including dismantling of old jalli and painting to match with existing complete all as specified and as directed.

S&F for Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer- In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)

S&F solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with Square tube, supply and fixing in opening as per specification given under SSR Part II 2010 including making good the disturbed surface all as specified and directed. Make: SYNTEX/SHALIMAR/RAJSHRI

M&L for factory made solid PVC panel type PVC door shutter 30mm thick consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rails, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and jointed together with solvent supplying and fixing in the frame at site as per specifications and drawing given under SSR Part II 2020 complete all as specified and directed. Make : SYNTEX/SHALIMAR/RAJSHRI

S&F 100 mm long stainless steel butt hinges fixed with stainless steel screw

S&F aluminum anodised barrel tower bolts of extruded section of size 150 mm length

S&F aluminum anodised barrel tower bolts of extruded section of size 200 mm length

S&F 150 mm extruded aluminum alloy handles, fabricated type anodised

S&F aluminum anodised sliding door, bolts with hasp and staple ( bolt type ) and fixing clip of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminum alloy, length of bolts 250 mm.

M&L PCC (1:2:4) type B1 using 20 mm graded stone aggregate as in hold fast, bed plate, coping, surface chanels etc including necessary form work complete all as specified and as directed.

M& L for preparation surfaces of new or previsouly untreated wood based surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer.

M& L for preparation old surfaces of wood of any description over 10 cm width or girth and applying One coat of synthetic enamel paint as specified.

Demolition of brick/cement concrete (unreinforced) / pcc tiles from existing roof/terrace etc and also removing/taking down of existing water proofing treatment of any thickness in any position including cleaning the surfaces of roof etc with wire brush complete and removing the retreived debris out side MD land, all as specified and directed.

M&L cement plaster (1:3) with 10 mm thick to be finished smooth without using extra cement mixed with WPC @ 2% by weight of cement, , complete all as specified and directed. Note : WPC shall be measured and paid separately as supply only.

Taking down complete existing APP membrane and M & L for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified with the following specifications complete all as specified and directed:- (a) Applying oil bound bitumen primer @ 0.40 litre/ Sqm manufactured by the same manufacturer as that of APP with a density 0.87-0.89 Kg per litre at 25 degree centigrade on the prepared dry surface. (b) Laying APP modified water proofing membrane reinforced with non woven polyester fibre weight not less than 160gm/Sqcm using butane torch by torch application with 10cm side lap and 15cm end lap. (c) Physical properties of membrane shall be as under:- (i) Membrane weight not less than 3.50 Kg/Sqm. (ii) Non woven polyester weight not less than 160gm /sqm. (iii) Softening point of membrane not less than 150 degree Celsius. (iv) Joint tensile strength-longitudinal not less than 650N/Sqcm and transverse not less than 450 N/Sqcm (v) Tear strength-longitudinal not less than 300 N & transverse not less than 250 N. (vi) Elongation : > 20% in both directions. (vii) Impermeability/water tightness at 2 Kgf/cm2. (viii) Water absorption - Not more than 1% on mass within 24 hours. (ix) Cold flexibility - Minimum (-) 20C. (x) Dimentional stability % change = Maximum 1%. (d) Over the membrane provide a finishing with solar reflective bitumen aluminium paint @ 0.10 Kg/Sqm as prescibed by manufacturer. (Note :- Bitumen primer paid separately)

S&F standard aluminium section powder coated (minimum thickness of powder coating shall be 50 micron and colour shall be as approved by GE ) as in frame, shutters for doors, window / ventilators, fixed / openable / sliding or in any pattern, cut to size, jointed with cadmium plated steel screws, including rubber beading or gaskets for fixing glass, provision of hinges, screws, plugs, handle, lock, roller, Nylon ball bearing etc complete all as specified and directed (Aluminium section shall be of make Jindal/Hindalco/ Indalco) Note:- Weight of Aluminium sections as per actual or as per IS or as per manufacturer, whichever is less, shall only be considered for payment. Cost of other items / accessories required for entire completion of the work shall be deemed to be included in the quoted rate. However glass panes, shall be measured and paid separately as supply only under respective item.

Supply only 4mm thick sheet glass, ordinary quality fixed in aluminium window along section all as specified and directed

Supply only Stainless steel wire cloth.0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples in aluminium windows or along with 'F' section complete all as directed by EIC.

Dismantling wrought iron or mild steel work of any description not otherwise provided for etc, complete all as specified and directed.

S&F bands, straps , supports or stays for rain water, ventilating pipes including bolts, clamps, hold fasts etc and similar small articles to Fe-410-0 or Fe-310-0 all as specified & directed.

S&F aluminium anodised Grills of approved design for window / ventilators and fixing with F/U channel including drilling as required in RCC sections in rectangular or architectual type balcony opening in existing building, complete all as specified and directed. Note: The Grills shall be of Model DG-100/DG-102 of Make Deco or equivalent make as approved by the GE.

S&F cast iron covers and frame grade FG 150 unmachined as in manhole covers etc including locking arrangement,and removing old Unsv covers complete all as specified

M & L Cement Concrete Type D2 1:4:8 (40 mm graded aggregate) in subbase 75 mm thick

M & L for sand filling under floors or in foundations including watering and consolidation

S & F MS bands, straps, supports or stays for rainwater, ventilating pipes, including bolts if reqd, hooks(stay), hook and pintle hinges, large hasp and staples, clamps, hold fasts, wall ties, plain angle cleats for securing purlins to wood trusses or rafters and similar small articles confirming to Fe-290 Gde E-165.

Preparation of new steel and iron surfaces of any description over 10 CM width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer.

M & L for Ready Mix concrete of M 40 Grade in pavement/hardstanding of flexural strength 40kg/per square centimetre in field using 400 kg of cement per cubic metre including vaccume dewatering complete all as specified and directed.

M & L for formwork to sides of concrete foundations and plinth beams and similar work vertical or to batter for flat and fair finished surfaces complete all as specified and directed

M & L for forming 12mm thick construction joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound Grade 'A' thk of concrete slab 150 mm complete all as specified and directed.

M& L for Acid resistant tiles of 15 mm thick vitreous ceramic unglazed set jointed and pointed in chemical resistant mortar resin type in floors completed as specified and directed

S& F in repairs steel rolling shutters without ball baering gear operated type without ball bearing as sppecified and including top cover anchoring rod hasp and staples and one shope coat of promer erected in position as indicated complete and wicket door including 4 lever mild steel safety lock lacakble from both side (area of of wicket door to be only measured)

S & F safety lever locks mild steel with 4 lever locks rolling shutters.

S& F ball bearing for rolling shutters

M & L in repairs for point wiring with PVC insulated FRLS unsheathed 1100 Volts grade single core multistranded copper conductor cable 1.5 Sqmm drawn in and including PVC concealed conduit of suitable size of wall/ RCC slab/ ceiling/ colunms/ beams etc with all accessories, fittings, PVC junction boxes etc, with suitabe sunk pressed steel boxes for modular fittings not less than 1.6 mm thick, including Modular cover plate of suitable size etc with necessary fixing accessories and earth continuity conductor cable of 1.5 Sqmm size connected to common earth and earth dolly including 1.6 mm thick pressed steel terminal boxes concealed in wall mounting switches / sockets / fan regulators fixed with Cadmium plated machine screws including taking down of old us worn out wiring, socket and fittings etc complete all as specified for one light / fan / bell point controlled by one switch. Note : 1. Two runs of cable, one run of earth wire, one run of PVC conduit will be measured and paid one unit. Make of conduit :- Sudhakar/ Precision/ Diamond, Make of wire :- Finolex/ Havells/ Polycab/ KEI

-Ditto- all as per item No 99 above but for one 5A 2pin/3pin switch socket out let multipurpose on independent Board.

All as per item No. 99 above but wiring complete with 2.5 Sqmm for 3 pin 15A socket multipurpose on independent board

S&F Switch Piano , one way, flush type, 5 Amps, 230 Volts ISI marked complete all as specified and directed. Make : Anchor/ Leader/ Maru/ Crabtree

S&F Switch Socket combination 2 in 1 , 5 Amps, flush type, 5 Pin, 230 Volts ISI marked, complete all as specified and directed. Make : Anchor/ Leader/ Maru/ Crabtree

S&F Switch Socket combination 2 in 1 , 5/15 Amps, flush type, 6 Pin, 230 Volts ISI marked complete all as specified and directed. Make : Anchor/ Leader/ Maru/ Crabtree

S&F ceiling rose three terminal, 230 Volts ISI marked PVC / Polycarbonate body, complete all as specified and directed. Make : Anchor/ Leader/ Maru/ Crabtree

S&F fan regulator, electronic stepped (5 step), 230 volts ISI marked, 100 watt, flush type and connecting-up, complete all as specified and directed. Make : Anchor/ Leader/ Maru/ Crabtree

S&F in repairs modular type 6A one way SP switch 1 module confirming to IS: 3854-1997 with fingure proof terminal complete all as specified and directed. Make : Anchor (Panasonic)/Legrand/ Havells (Crabtree)

S & F in repairs modular type 2/3 pin 6 Amps socket 2 module conforming to IS: 1293-2005 complete all as specified and directed. Make : Anchor (Panasonic)/Legrand/ Havells (Crabtree)

S & F in repairs modular type 2/3 pin 16 Amps socket 2 module conforming to IS: 1293-2005 complete all as specified and directed. Make : Anchor (Panasonic)/Legrand/ Havells (Crabtree)

S & F in repairs modular type 16 A one way SP switch 1 module confirming to IS: 3854-1997 with fingure proof terminal complete all as specified and directed. Make : Anchor (Panasonic)/Legrand/ Havells (Crabtree)

S & F in repairs modular type 120W step fan regulator of 2 module size conformng to IS: 11037-1984 complete all as specified and directed. Make : Anchor (Panasonic)/Legrand/ Havells (Crabtree)

Supply & Fix in repairs Modular Bell push flush type 6 Amp, 1 module, 230 Volts complete all as specified and directed.

Supply and fix in repairs bell ding dong AC 230 V single pole. complete all as specified and directed.

S & F in repairs Modular Blank plate 1 module suitable for Modular switch boards all as specified and as directed

S & F Modular cover plate 12 modules

S & F Modular cover plate 8 modules

S & F Modular cover plate 3 modules

S & F Modular cover plate 1 modules

Supply & Fix smart extruded aluminium LED batten (4ft) of capacity 20W with higher efficacy microwave sensor to save more energy, reduces the light intensity by 70% during non- occupancy, operating on 230V, 50Hz, AC Supply having luminous efficacy of not less than 100 lumens/watts, CCT 6500K, P.F>0.9, 2.5 KV surge protection, made out of extruded aluminium with decorative end caps elegently designed complete all as specified. Make :-BAJAJ/ JAGUAR/ WIPRO

Supply and fixing recessed mounted 2ft x 2ft LED luminaire 36 W with deep drawn CRCA housing efficacy of 120 lm/w, 220 V AC of CCT 5700K with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete. Make :-BAJAJ/ JAGUAR/ WIPRO

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC of CCT 6500K, decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engr-in-charge. Make :-BAJAJ/ JAGUAR/ WIPRO

S & F LED light fitting 1X10W Bulkhead luminaires of PDC housing including LED light driver, equipped with 2 kv in-built surge protection wtih IP65 protection rating of CCT 5700K connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. Make :-BAJAJ/ JAGUAR/ WIPRO

Taking down in repairs old unserviceable ceiling fan 1200 mm sweep by disconnecting the electric power supply, unscrewing the bolts and nuts, removing the blades and transporting to workshop to undertake repairs by rewinding of burnt out winding using suitable gauge copper wire, replalcement of worn out capacitor 2.5 mfd - 01 No., PVC canopy - 02 No's and bearing including scrapping of old paint and applying two coats of synthetic enamelled white paint over a coat of red oxide primer complete and refixing back at site complete all as directed.

Supply and fix Ceiling fan with BLDC motor complete with blade, canopy, down rod, mounting hook, rubber insulator etc, the colour of fan shall be of Elegant White/Dubai white/ White CF without remote control alongwith batteries and accessories 230 V, 1200 mm sweep, BEE 5 Star rated complete including takingdown old unserviceable fan all as directed by Engr-in-Charge. Make : Havells (Efficiencia Neo (BLDC 26 W) /Orient / Bajaj / Panasonic (Captor i-Kraft) Note : Unserviceable ceiling fans shall be deposit to MES store.

Supply & Fix Heavy duty Metallic Body Exhaust fan of sweep 380 mm with frames, blades including provision of mounting anchor fasterners aluminium louvers made of aluminium sheet of 0.5 mm thickness provision of three core 1.5 sqmm copper cable from ceiling rose to fan, making opening of required size in cement mortar brick wall/ RCC for fixing of exhaust fan, making good the disturbed surfaces in CM 1:4 including scafolding if any required to carry out the work in building of height up to 20 meters complete. Make - ALmonard/ Orient/ Crompton

Taking down old unserviceable exhaust fan 300 mm sweep by disconnecting the electric power supply, unscrewing the bolts and nuts, removing the blades and transporting to workshop to undertake repairs by rewinding of burnt out winding using suitable gauge copper wire, replalcement of worn out capacitor 2.5 mfd - 01 No. and bearing including scrapping of old paint and applying two coats of synthetic enamelled white paint over a coat of red oxide primer complete and refixing back at site complete including provision of new louvers of shutter type of suitable size all as specified and directed.

S & F in repairs MCB DB, 12 way, SPN, double door, 240 Volts and including cutting chases in wall, concealing DB in wall, making good the disturbed surfaces and making all connections complete including taking down old us DB all as specified and directed. Note: Quoted rate shall be deemed to include for provision of copper bus bar of 200 Amps rating. Make :-LEGRAND / SCHEINDER / L & T.

S & F in repairs MCB SPN 20 to 32 Amps, 240 Volts, 50 Hz, 10 KA Breaking capacity. Make :- LEGRAND/ SCHEINDER/ L&T

S & F in repairs MCB SP 5 to 32 Amps, 240 Volts, 50 Hz, 10 KA Breaking capacity. Make :- LEGRAND/ SCHEINDER/ L&T

S&F modular type 3/5 pin socket with one single pole MCB 20 Amp 230 Volts complete all as specified including concealing in wall suitable for Geyser, AC and Domestic appliances complete all as specified and directed. Make - Havells/ Legrand/ Schneider

M&L in repairs for sub main wiring with two single core 4.0 Sqmm PVC insulated FRLS multistranded flexible copper conductor cable 660/1100 volts grade down in through non metalic PVC casing caping with and including PVC insulated 4 Sqmm single core single strand copper conductor as continous earth wire in green colour connected to common earth dolly all as specified and as directed. (Make :- PRESFIT/ PRECISION - Casing caping), (Make :- FINOLEX/ KEI/ POLYCAB - PVC Copper wire) Note : 1. Two runs of cable, one run of earth wire, one run of PVC casing capping of 4.0 sqmm will be measured and paid one unit.

M&L in repairs for sub main wiring with two single core 6.0 Sqmm PVC insulated FRLS multistranded flexible copper conductor cable 660/1100 volts grade down in through non metalic PVC casing caping with and including PVC insulated 6 Sqmm single core single strand copper conductor as continous earth wire in green colour connected to common earth dolly all as specified and as directed. (Make :- PRESFIT/ PRECISION - Casing caping), (Make :- FINOLEX/ KEI/ POLYCAB - PVC Copper wire) Note : 1. Two runs of cable, one run of earth wire, one run of PVC casing capping will be measured and paid one unit.

M&L in repairs for sub main wiring with two single core 1.5 Sqmm PVC insulated FRLS multistranded flexible copper conductor cable 660/1100 volts grade down in through non metalic PVC casing caping with and including PVC insulated 1.5 Sqmm single core single strand copper conductor as continous earth wire in green colour connected to common earth dolly all as specified and as directed. (Make :- PRESFIT/ PRECISION - Casing caping), (Make :- FINOLEX/ KEI/ POLYCAB - PVC Copper wire) Note : 1. Two runs of cable, one run of earth wire, one run of PVC casing capping will be measured and paid one unit.

S & F in replacement building Security light fitting 35/36 Watt made up of pressure die cast alluminium body with mid power LED as lighting sources and PC cover having Top opening separate driver compartment with IP 65/66 protection and impact resistance of IK 07 including fixing arrangements and taking down old rusted bracket fittings complete all as per directed by Engr- in – charge. Make :- JAQUAR/ WIPRO/ PHILIPS/ BAJAJ

S & F in replacement of GI steel tubing medium grade 40 mm dia and length up to 1.5 meter bent to shape of offset angle upto 45degree for fixing of security /street light fittings including MS clamps made of 32mm x5mm flat iron, nuts , bolts, etc all as directed by Engineer in charge

M & L in repairs for Earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised MS strip 32 x 6 mm by means of bolts, nuts, check nuts and washers all as shown in Electrical Plate No.3 connected to earthing test point all as specified or indicated including testing on completion.

Taking down carefully including water servicing of outdoor & indoor which including cleaning of cooling coils, tightning of loose terminations and refixing of same Window and split type AC 1.5/2.0 TR and carrying out brazing/ welding and replacement of worn out connected items complete all as specified and directed.

Supply and fix in repairs copper tube of size 1/4" bore including brazing etc with rubberised insulation and tape suitable for supply pipes for air conditioners complete all as specified and directed.

Supply and fix in repairs copper tube of size 5/8" bore including brazing etc with rubberised insulation and tape suitable for supply pipes for air conditioners complete all as specified and directed.

Supply and fix in repairs PVC drain pipe of size 5/8" bore for supply pipes for air conditioners complete all as specified and directed.

Supply and fix in repairs 4 core 2.5 sqmm PVC insulated FRLS multistranded flexible copper conductor cable 660/1100 volts grade ISI marked complete all as specified and directed.

Supply and fix in repairs Heavy duty Water Proof Powder coated mounting bracket for installation of outdoor unit of air condiioner made out of 2 mm thick high grade steel with suitable fastener, MS nuts, bolts M8 x 45mm, washer, bolt M8 x 30mm nut, bolts & washers etc. duly painted complete set all as specified and directed. Make :- Companion Sleek, Aircool Sales Corporation or equillant make Note : A sum of Rs 41,557.00 towards sch of credit shall be deducated to arrive the contract sum.

M/s Shree Construction Co

AM ENTERPRISES

M/s Mukesh Engineers

KRISHNA ENGINEERS

Joy builders

Parmatma Enterprises

M/s Mohd Altaf Hanif Qureshi

Vishal Builders

RAJU AND COMPANY