REPAIR TO ROOF TREATMENT, SUNKEN FLOOR, CHAJJA, FACIA TO OTM/MD ACCN AT 508 ABW, CHHEOKI.

Amount

Demolition of cement concrete in ground floor and paving not exceeding 15cm thick below or above ground level unreinforced complete all as specified and directed. .

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Demolition of brick work built in cement mortar of any description including all quoins arches, pillars, etc and removing debris complete all as specified and directed.

M & L Brick work with fly ash bricks, straight or curved on plan exceeding 6m mean radius, built in cement mortar 1:6 complete all as specified and directed

M & L for brickwork with fly ash bricks, straight or curved on plan to any radius in half brick thick walls, built in 1:4 CM complete all as specified and directed

M&L for reinforced cement concrete 1:2:4 type B1 using 20mm graded aggregate as in slabs supported on walls, beams, and columns in floors, roofs landings, balconies ,canopies , deck slabs and in shelves and the like complete all as specified and directed. Note:- Reinforcement to be measured & paid separately under respective item.

Form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick, for rough finished flat surfaces of concrete complete all as specified and directed.

Form work to edges of concrete flats, openings, floors & roofs and sides of RCC/PCC bands in walls and similar work exceeding 10cm but not exceeding 20cm wide for rough finished surfaces of concrete complete all as specified and directed.

Use & waste of form work to sides and soffit of floor or roof beams, beam haunching, girders, bressumers, lintels, cantilevers, shelves including supports, overhangs chajja etc also splays between floor & roof beam etc for rough finished surface of concrete complete all as specified and directed

M&L TMT bar 10 mm dia & over cut to length, bent to shape required ,including cranking ,bending spirally for hooping for columns, hooking end and binding with and including mild steel wire and annealed not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M&L TMT bar 5 mm dia & over upto & including 10 mm dia in stirrups, spaces and binders , cut to length, bent to shape required ,including cranking ,bending spirally for hooping for columns, hooking end and binding with and including mild steel wire and annealed not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M&L for 75 mm thick cement concrete 1:3:6 type C2 using 40 mm graded stone aggregate in plinth protection finished even and fair including necessary form work and cutting of joints etc complete all as specified.

Dismantling of floor hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises and removing debris complete all as specified and directed.

M & L for non skid joint free coloured ceramic floor tiles 7 to 8 mm thick (square/ rectangular) area of each tile exc 0.11 sqm but n exc 0.18 sqm, in floor ,wall etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the surface with 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and directed.

M&L non skid, joint free ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.18 and n.exc 0.38 Sqm in floor, shelves etc, set and jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles over and including 15 mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified and directed.

M&L non skid, joint free ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.18 and n.exc 0.38 Sqm in vertical surface set and jointed in neat cement slurry & pointed in coloured cement to match the shade of tiles over and including 10 mm thick screed bed or bedding layer in cement mortar 1:4 complete all as specified and directed.

M&L for joint free glazed ceramic coloured wall tiles in vertical surface 450X300X 6-7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10 mm thick rendering in 1:4 CM complete all as specified and directed.

M&L for joint free glazed ceramic coloured wall tiles in vertical surface 1200 X 600 X 9-10 mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick rendering in 1:4 CM complete all as specified and directed.

M&L for joint free vitrified ceramic coloured tiles 9 - 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.42 sqm but not exceeding 1.00 Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles over & including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for joint free vitrified ceramic coloured tiles 9 - 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.42 sqm but not exceeding 1.00 Sqm in skirting, dados etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match tiles over & including 10mm thick rendering in CM 1:4 complete all as specified and directed.

Taking down cement plaster on brick or stone walls including wall tiles etc. with raking out joints, hacking for key, scrubbing down with water, etc and removing debris complete all as specified and directed

M&L for rendering 15mm thick in CM 1:6 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 10mm thick in CM 1:3 on ceiling surfaces of RCC or brick surface finished even & smooth without using extra cement complete all as specified and directed.

M&L for preparing new plastered or unplastered surfaces of wall and applying two coats of oil bound distemper over a coat of primer over & including 1 mm wall care putty on wall including rubbing with sand paper to achieve a smooth surface and sharp straight edge etc complete all as specified and directed.

M&L for preparing of newly plastered wall surface by sanding and applying two coat of exterior weather proof anti algae 100% acrylic emulsion over a coat of exterior water based primer. The primer and paint will be applied through airless spray technology with max working pressure of 3300 PSI by Trucare Graco Machine / Airless paint sprayer / Airless sprayer machine and capable of operational single spray gun with a maximum material hose length 150 M working complete all as specified and directed. Note: (i) Airless spray machine of Make VAnds Engineering solutions / Surya 9 (Jaguar) / Control Pro 190 (Wagner) shall be used for painting. (ii) Sanding of new surface to be done by mechanical sander with 1500-2700 rpm, with internal dust extraction system for clean environment, certified by paint manufacturer.

Taking down existing sunken portion treatment by demolition of old concrete and carry out the sunken treatment as in following steps given below :- (a) S&F of drainage spout GI pipe 40 mm dia bore light grade upto outside of outer wall (Approx 450 mm to 600 mm long). (b) M&L for PCC 1:1.5:3 type A-0 using 12.5mm graded stone aggregate, 50 mm thick laid in slope towards drainage out spout pipe mixed with waterproofing chemical as per manufacturer instructions of MAKE :FOSROC/SIKA/ Pidilite/STP. Khurra 150mmx150mm (min) at appropriate location for free flow of leaked water if any, towards drainage spouts shall be provided integrally while laying PCC.Fixing of spout shall be done with same PCC as in this item. (c) M&L for 18 mm thick cement plaster in CM 1:3 on vertical faces mixed with water proofing chemical of MAKE :301 Pidicrete URP of Dr Fixit / SIKA/ Pidilite/FOSROC/STP (d) Work shall be executed while concrete is green and proper curing and ponding test shall be done before laying drainage/water supply pipes upto the entire satisfaction of Engineer in charge. (e) Applying two coats of top seal coat layer of SIKA / FOSROC /Pidilite/Dr Fixit/STP on vertical as well as horizontal surface. (f) Drainage and water supply pipe if required & test for leakage/sanitary pipes and shall be laid to slope and a clear gap underneath the pipes shall be made available by providing suitable cement concrete blocks. (g) M&L PCC1:5:10 type E-2 using 40 mm graded stone aggregate as reqd depth at site including 150mm thick 20mm single sized stone agg to provide a filter media. (h) M&L PCC 25 mm thick 1:2:4 type B-0 using 12.5 mm grade stone aggregate as level course.

(j) M&L for 7 to 8 mm thick non skid ceramic coloured joint less tiles (square/ rectangular) area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm as in floors etc; laid jointing in neat cement slurry and pointed filled with epoxy chemical make: SIKA/FOSROC/PIDILITE/ Dr Fixit/STP.mixed with pigment to match with shade of tiles over and including 15 mm thick screed bed in CM 1:6 complete all as specified and directed. Note:- (i) Waterproofing Treatment shall be undertaken alongwith laying of drainage pipes/Sanitary pipes/ Drainage Spout etc (ii) The work shall be carried out as per the direction of Engineer in Charge. (iii) The sunken treatment work shall only be carried out after written approval of Engineer in charge for Leakage/seepage of water/sanitary pipes. (iv) Cost of drainage spout shall deemed to be included in the item however sanitary pipe, water pipe line if required shall be paid separately under respective item. (v) Laying of Chemical required for various applications shall be as per manufacturer instructions. (vi) Top plan area shall only be measured and paid.

Taking up or down 15 mm bore GI steel tubing and connections on (walls, ceiling, floors, etc.) including cleaning complete all as specified and as directed

Taking up or down 20 mm bore GI steel tubing and connections on (walls, ceiling, floors, etc.) including cleaning complete all as specified and as directed

Cutting chases, pinning in making good to facing where required for concealed water tubing and making good cutting not exc. 10 cm girth in brick walls complete all as specified and directed

S&F of steel water tubing, medium grade, ISI marked galvanised, 15 mm bore with all fittings, fixed to walls and ceiling or laid in floors complete all as specified and directed

S&F of steel water tubing, medium grade, ISI marked galvanised, 20 mm bore with all fittings, fixed to walls and ceiling or laid in floors complete all as specified and directed.

S&F in repair stop valve angular type 15mm dia, fancy type chromium plated with long shank & cup (concealed type) screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe or for unions and fixed complete and fixed all as specified and directed.

S&F in repair brass CP WHB mixer for mixing hot & cold water screwed down for iron pipe in the bore of 15mm dia pipe complete all as specified and directed.

S&F in repair vitreous china wash basin oval type under over counter shape of size 550x460 mm laid over stone slab including brackets of approved size including necessary cutting for and pinning in ends of brackets in cm 1:3 including 32 mm dia Chromium plated waste coupling complete all as specified and directed

S&F 15 mm bore PVC connection 60 cm long heavy duty with brass fly nuts & washer for hot and cold water complete all as specified.

S&F in repair brass chromium plated shower rose 125 mm size , shower arm with or without swivel joints complete all as specified and directed.

S&F in repair PVC flushing cistern 10 ltr capacity valve less symphonic action type low level with and including ball valve float & handle, waste pipe & brackets complete set all as specified and directed.

S & F in repairs vitreous China white wash down water closet pan (pedestal pattern) including fixing bolts, plastic water closet white. seat cover closed pattern with flat bottom (white colour) and cover and mild steel chromium plated or aluminium hinging device complete all as specified and directed.

S&F in repairs WC squatting pan “Orissa Pattern” of size 580 x 440mm white with integral foot rest (excluding flushing cistern & flush pipe) including connection to trap and to flush pipes etc and lime concrete bedding complete all as specified in SSR and including 'P' or 'S' trap complete all as specified and directed.

S&F in repair rotational moulded, triple layer HDPE water storage tank (white colour three layer) of 1000 ltrs capacity(Cylindrical vertical with closed top) ISI marked fixed in position on existing places complete and refixing of inlet, outlet & overflow pipe etc, complete all as specified and directed.

S & F in repairs 600 mm long tubular towel rail , brass chromium plated of 20 mm dia complete all as specified and directed.

S&F 15 mm dia health faucet abs body with 8 mm dia 01 mtr long flexible tube & wall hook chromium plated complete all as specified and directed.

S&F solid PVC frame (Single rebated) of size 60 x 30 mm made out of solid PVC foam with homogeneous fine cellular structure having smooth outer integral skin with suitable metal stiffener and fixed with 100 x 8 mm sheet metal CSK screw complete all as specified and directed. Note:- Door frame shall be water proof, termite proof, elegant and should have excellent screw holding strength to fix hinges and hold doors properly for a long life.

S&F factory Made Solid PVC Moulded Door Shutters 28 to 30 mm thick with partical board core (stile:) with 2,4 or 6 raised panel design with 2 mm thick 3D wood grain moulded prelam PVC Sheet polyurathene painted on the front Face & 2 mm prelam PVC sheet on back face & fixing in frame at site fixed in repair complete all as specified and directed.

S&F for 100 mm long anodised aluminium butt hinge of extruded aluminium alloy with galvanised mild steel hinge pin complete all as specified and directed.

S&F 125 mm long anodised aluminium barrel tower bolt of extruded section, fabricated type fixed with screw complete all as specified and directed.

S&F 125 mm long anodised aluminium handles of extruded section, fabricated type fixed with screw complete all as specified and directed.

S&F 150 mm long anodised aluminium handles of extruded section, fabricated type fixed with screw complete all as specified and directed.

S&F 200 mm long anodised aluminium barrel tower bolt of extruded section, fabricated type fixed with screw complete all as specified and directed.

S&F in repair 300mm long aluminium alloy anodised sliding door bolts , with hasp staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast-aluminium alloy complete all as specified and directed .

S&F 300 mm, ordinary rat tail rod pattern springs of mild steel including roller and roller plate complete all as specified and directed.

S&F 75 mm long alumium alloy extruded type door stopper of double legged with rubber shoe in bottom complete all as specified and directed.

Cutting holes in brick walls built in cement mortar, for inserting hold fasts exceeding half brick but not exceeding one brick and making good dismantled portion in CM 1:3 or cement concrete 1:2:4 type B1 complete all as specified and as directed.

All as per item No 56 but wire gauged window complete all as specified and directed.

All as per item No 58 but wire gauged window complete all as specified and directed.

S & F framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

M&L for rigid PVC foam profiles ventilator, horizontal frame member is made of profile of required size 88 x 12 mm and vertical member strips are made of 71 mm x 28 mm with MS pipe stiffener ( 19 x 19 x 0.8 mm thick) vertical frame member with help of required size CSK screw and adhesive, total unit is fixed with help of bracket / fasteners including 4 mm thick frosted glass & SS jalli as per requirement complete all as specified and directed.

S&F aluminium section powder coated frame of colour as approved fixed type ventilator with one or more rebates including joining cleat for fixing etc complete all as specified and directed.

S&F in repair powder coated aluminium anodised door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing handles 2 Nos in each door, hinges, anodised aluminium snap beading screws with provision of double action floor spring etc complete all as specified and directed.

S&F powder coated aluminium anodised window and ventilator, side hung type, without sash, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long(1No), hinges type B 21 100mm long( 2 Nos) suitable handle (1No) complete all as specified and directed.

S&F powder coated aluminium anodised wire gauged window without sash, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long(1No), hinges type B 21 100mm long( 2 Nos) suitable handle (1No) complete all as specified and directed.

S&F 5 mm thick glass each pane fixed on aluminium door shutter with and including aluminium beading, rubber gasket etc complete all as specified & directed.

S&F for Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples all as specified & directed.

S&F in repair Stainless steel tubing of 25 mm dia for curtain rod fancy type with brackets including end cap (wall to wall or flush to wall) for securing to curtain rod complete all as specified & directed.

Dismantling boarding any description fixed with screw or nails and similar work complete all as specified and directed

M&L for 20 mm thick PVC board made out of 18 mm thick PVC ply and 1 mm thick PVC ply free from rigid one side prelaminated and another side plain colour, PVC sheet stuck on both side with solvent cement adhesive to make the board of 20 mm thick cup board and wardrobes complete all as specified and directed

M&L for 18 mm thick coloured MDF board with hardwood fibers prelaminated both sides including cutting as in kitchen cabinet, almirah shutter including teakwood liping 6 mm thick with necessary lipping as in repair complete all as specified and directed.

All as per Srl item No. 71 but as in shelf and partition including 6 mm thick teak wood lipping with necessary polishing complete all as specified and directed.

M&L for 100 mm size stainless steel hinges auto close type complete all as specified and directed.

M&L for 125 mm size stainless steel handle flush type complete all as specified and directed.

S&F 30mm width of flaps continuous (piano) hinges, mild steel, bright finish or electro galvanised complete all as specified.

S&F 40 mm width of flaps continuous (piano) hinges brass complete all as specified.

S&F 100 mm hasp & staple safety type of aluminium anodised including bolt to hinges plate and fixed with screws complete all as specified and directed.

S&F ball & catches with 8 mm dia steel ball and brass body and skirting plate including letting in and fixed complete all as specified and directed.

S&F 40 mm dia brass polished cup board knobs fixed with nut, screw & washer of mild steel bright finished complete all as specified and directed.

S&F stainless steel roller plate with rollers suitable for sliding cupboard drawer complete all as specified and directed.

S&F stainless steel tray, bucket & basket of suitable shape and size for modular kitchen & fixing as per manufacturer's instruction complete all as specified and directed.

Dismantling of brick tiles or terracing tiles, single layer on roofs complete all as specified and directed.

Demolition of roof treatment by using hand electric drills, cutting machine, chisel etc (direct use of hammers on RCC roof for demolition is strictly prohibited) of roof treatment including padding concrete of any description including mud in roof any thickness with & including roughening old concrete surface by picking, sweeping clean and washing down with water to remove dust etc complete all as specified & directed.

M&L for PCC 1:2:4 type B0 using 12.5 mm graded stone aggregate as in roof curbing, padding over roof slab complete all as specified and directed. Note - Average thickness shall not exceed 40mm

M&L for rendering 10 mm thick on concrete surface when concrete is green on roof surface in cement mortar 1:3 mixed with liquid water proofing compound finished even & smooth without using extra cement complete all as specified and directed.

Supply only Water proofing compound complete all as specified and directed

Schedule of Credit (MINUS) Rs. 42170.00 B/F from Serial Page No. [Note : Details of items for schedule of credit is given on Srl Page No. ] This amount shall be automatically deducted to arrive at tendered sum

M/S VIVEK DUBEY

Airways Enterprises

Vijay Builders