PROVN OF SINGLE JCO ACCN OF AD REGT AT DHANGU MILITARY COMPLEX AND PROVN OF RCC FRAMED SECURITY WALL NEAR GD POST NO 9 AT 2 ASD UNDER GE SOUTH PATHANKOT

Amount

Surface excavation not exc 30 cm deep and averaging 15 cm deep and getting out in hard dense soil.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth for foundation etc in any type of soil and getting out complete all as specified.

Excavating over area not exc 1.5 m deep & getting out in any type of soil

Returning filling in including spreading, levelling, watering and well ramming in layers n. exc 25cm thick all as specified.

Removal of excavated material soil n. exc 50m and depositing where directed at a level n. exc. 1.5 above the starting point all as specified.

M & L for cement concrete M-10 nominal mix (using 40 mm graded stone aggregate) as in foundation filling and mass concrete.

M&L PCC 1:4:8 type D-2 using 40mm graded agg. as in foundation filling and mass concrete complete all as specified.

M & L for reinforced cement concrete M-25(design mix) using 20 mm aggregate in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified.

M & L for reinforced cement concrete M-25(design mix) using 20 mm aggregate in columns, pillars, piers, posts and struts

M & L for reinforced cement concrete M-25(design mix) using 20 mm aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified & directed.

M & L for reinforced cement concrete M-25(design mix) using 20 mm aggregate in beams, cantilevers, shelves, bressummers, lintels over 1.5m span

M&L for RCC(M-25) design mix as in wall/ retaining wall, any thickness above top of footings; including attached pilasters and buttresses, complete all as specified & directed.

M&L Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work vertical or to batter Rough finished surfaces of concrete Flat

M&L Formwork to sides of pillars, posts, struts, piers, columns and stanchions Rough finished surfaces of concrete Square, rectangular or polygonal

M&L Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) - Rough finished surfaces of concrete - Flat

M&L Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc Rough finished surfaces of concrete Flat

M&L mild steel TMT bars 10mm dia and over cut to length, bent to shape, required including cranking, bending, spirally for hopping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified .

Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified.

M&L Brickwork with fly ash old size bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) complete all as specified and directed.

M&L for Brick work with fly ash bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1: 4

M&L for Brick work with fly ash bricks, straight or curved on plan exc 6 m mean radius built in cement mortar 1: 4 in half brick thick wall.

M&L cutting chases, pinning in brick work for concealed water tubing and making good to facings where required and pointed in cement mortar 1:3 cutting not exceeding 10cm girth all as specified.

S&F15mm bore tubes medium grade galvanized ISI marked with all fittings short pieces and fixed complete to walls all as specified.

S&F Tubes 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors - Bore of tube 20mm

Supply and lay in trenches/ on roof/ on wall/ 25mm dia bore steel water tubing galvanised medium grade with all fittings of following sizes, complete all as specified and directed.

Supply and lay in trenches/ on roof/ on wall/ 40mm dia bore steel water tubing galvanised medium grade with all fittings of following sizes, complete all as specified and directed.

S&F for 25mm dia gun metal gate valve with iron wheel head screwed both ends for iron pipe of following sizes complete all as specified and directed by Engr-in-charge.

S&F for 40mm dia gun metal gate valve with iron wheel head screwed both ends for iron pipe of following sizes complete all as specified and directed by Engr-in-charge.

Cutting cast iron pipes up to 80 mm dia and reducing to required length in position for insertion of new tees, branches, etc all as directed by Engr-in-charge. Note : CI fittings/Lead joints will be measured and paid under relevent items

M&L for construction of masonry valve chamber of size 750x750x750mm complete including demolition and removing of debris of the existing chamber all as specified and as directed.

M&L for 15mm thick plaster in cement mortar 1:4 on fair faces of brick work or concrete surfaces finishing the surfaces even and smooth without using extra cement all as specified.

M&L rendering 10mm thick on concrete in CM 1:3 in facia or edging of chajjas,ceiling and roof projection making the line in true shape finished even & smooth without using extra cement all as specified.

M&L for Rendering 10mm thick in cement mortar 1:6 on fair faces of brick work or concrete surfaces finishing the surfaces even and smooth without using extra cement, complete all as specified & directed.

M&L for preparing the new plaster surface and applying three coats of white wash on ceiling, complete all as specified & directed.

M&L for two coats of cement base paint over a coat of primer over prepared surface of wall, complete all as specified & directed.

M& L for two coats of synthetic enamel paint over a coat of red oxide on steel surface, complete all as specified & directed.

M&L for two coats of oil bound distemper over a coat of primer over prepared surface of wall by applying 1-2 mm thick wall care putty complete all as specified.

M&L for broken stone or boulder hardcore of guage n exc 63mm, deposited, spread and levelled in layers n exc 15 cm thick, watered and rammed to a true surface

M&L 75 mm thick PCC 1:4:8 as in sub base of floors etc and finishing the surface even and smooth without using extra cement complete all as specified.

M&L providing glazed ceramic coloured tiles in vertical surface 350x250x7mm/ 450x300mmx7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile, over 10mm thick rendering in CM 1:4 all as specified.

M&L Vitrified ceramic tiles 8 mm thick (Square/rectangular) polished area of each tile not exceeding 0.36 sqm in floor or dado/skirting etc set and jointed in neat cement slurry and pointed in coloured cement match the coloured tiles over 15mm thick screed bed in cement mortar 1:4 all.

M&L Non skid ceramic colour tiles 7 to 8 mm thick ( sq/ rect) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

M&L for 20mm Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, win- dow-cills, cooking plat- forms and like in cement mortar (1:4) including point- ing in white cement (1:2) us- ing marble dust with admix- ture of pigment to match with shade of granite.

S&F pressed steel frame for doors made out of MS sheet 1.25mm thick of size 125x60mm for with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc including filling of concrete 1:3:6 type C-1 back of chowkhats all as specified.

S&F 35mm thick HDF prelaminated (Wenga/Teak coloured ) moulded shutter PUF(Poly urathane foam ) insuation with minimum density 40Kg/Cum filled in between two HDF sheets of thickness 3.2mm both & border covered with 10mm thick PVC sheet as per Drg No. CEPZ/TD-378/sheet 1/1 dated 27/12/2011 complete all as specified and directed.

S&F 35mm thick single piece factory made wire gauge door shutter of (steel & aluminium XPM) manufacturing by PVC sheets printed 5mm thick on both side on frame made out of MS tube 19 SWG size 19 x 19mm complete in all respect with lock rail & beautified by PVC beading all around fixed with PVC solvent cement complete as per Drg No.CEPZ/TD-378/Sheet 1/1 dated 27/12/2011 complete all as specified and directed.

S&F Solid PVC door frame(Single frame) of size 60mmx30mm made out of solid PVC foam with hmgenous fine cellular stucture having smooth outer integral skinwith suitable metal stiffner and fxed with 100x8 sheet etal CSK screw cmplete all as specified and shown on drawing.Note :- Door frame shall be water proof, terite proof, elegant and should have excellent screw holdig strength to fix hinges abnd hold doors properly for a long life)

S&F for Factory Made Solid PVC Moulded Door Shutter wood free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing

S&F steel window/ventilator with tubular frame factory made of size 79mm x 39mm, 16 gauge rectangular tubular frame with side hung shutter both for glazed and wire gauge with glazing bars 12x3mm flat iron incl projecting type hinges with steel handle and steel peg stay dovetailed or welded incl 2 Nos tower bolts 100mm long and 10mm square bar grills complete, including two coats of synthetic enamel paint over one coat of red oxide primer all as specified & as shown on drg No CEPZ/TD-245/01 and 246/02 sheet ½ & 2/2 (excluding glass & wire guage).

S&F sheet glass 3.00mm thick ordinary quality and glazing with oil putty in square n.exc 0.50Sqm in each panes complete all as specified and directed.

S&F glavanized mild steel wire cloths 0.56mm nominal dia and average width of aperture 1.18mm & fixed with tint tacks or glavinized wire staples complete all as specified and directed.

S&F 300mm ordinary mild steel springs ISI marked including roller and roller plate complete including all necessary welding if required.

S&F 150mm long aluminium, anodized barrel tower bolts of extruded section ISI marked

S&F 150mm extruded aluminium alloy handle fabricated anodized ISI marked .

S&F 100mm long butt hinges medium weight cold rolled ISI marked mild steel .

M&L for 10mm thick rendering in Cement mortar 1:4 mixed with WPC 3% by weight of cement on fair faces of concrete roof surfaces , finished even and fair to receive treatment on roof complete all as specified and directed.

Providing and laying of water proofing treatment of roof APP (Atactic Polyproplyllen) modified prefabricated five layer 3mm thick water proofing membrane, super thermply non woven polyester mat reinforcement of 160 gsm, weight of membrane @ 3.6 Kg/Sqm over a solvent based bitumen primer @ 0.3 Ltr Sqm by the same manufacturer conforming to IS:3384-1986 , The membrane shall be laid using bitmun torch.The end lap should be 100 mm and the side lap must be minimum 75 mm the membrane shall be first laid up to the parapet wall junction and then shall be overlapped with another membrane (flashing) with an overlap covering up to a distance of 300mm. In case parapet height is less than/ up to 500 mm, membrane shall be terminated at the top of parapet.All rain water pipe opening shall be suitably sealed with the APP membrane all as specified and directed. (The rate includes for filling cracks in existing roof with cement putty using suitable bonding agent (shalcrate 42) before laying cement plaster)

Supply only liquid water proofing compound of approved brand.

S&F angle valve 15mm bore size fancy type cast copper alloy chromium plated as per Cat Part No. T0410C of Prayag or technocommercial equivalent complete all as spd & directed.

S&F stop valve 15mm bore size concealed fancy type, as per Cat Part No.T0413C of Prayag or technocommercial equivalent complete all as spd & directed.

S&F 20mm bore stop valve cast copper alloy, screwed down high pressure with crutch or butterfly handle, screwed both ends for iron of pipe or for unoins all as specified.

S&F Chromium Plated wall mixture valve cast copper alloy fancy type for mixing hot and cold water screwed down high pressure with capstan head screwed both ends for iron pipe 15mm bore dia complete all as specified and directed.

S & F long nose bib taps 15mm bore size fancy type cast copper alloy chromium plated as per Cat Part No.T1006C of Prayag or technocommercial equivalent complete all as spd & directed.

S&F Centre hole basin mixture valve, cast copper alloy fancy type, chromium plated, for mixing hot and cold water screwed down high pressure with capstan head screwed both ends for iron pipe 15mm bore dia complete all as specified and directed.

S&F for CP Soap Dish fixed with and incl CP screws of as approved by Engr-in-Charge.

S&F Tubular towel rail 20mm dia ‘D’ type 60cm long between flanges brass chromium plated.all as specified and approved.

S&F rotational moulded polythene water storage tank triple layered (Cylindrical vertical with closed top hoisted fixed in position all as specified capacity of tank 1000 ltrs including inlet and out let connections 20 mm air and 15 mm dia GI pipe medium grade.

S&F in repair 20mm PTMT ball valve high pressure with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed complete all as specified

S&F in repairs vitreous china wash down water closet (pedestal pattern) including fixing bolts and connecting to drain pipe including seat cover plastic flat bottom and jet spray and connection to flush pipe, anti syphonic pipe etc complete all as specified and directed.

S&F flush pipe of polythene of low or high density tube 32mm dia for low level cistern.

S&F PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets of 10 Ltr capacity.

S&F for 550x400mm counter top oval wash hand basin model comet of light shade including CP coupling CP bottle trape complete with and incuding top finished with 25mm thick granite over and incuding cement screed 15mm thick in cement mortar 1:4 jointed and pointed in coloured cement complete all as specified and directed .

S&F brass chromium plated overhead shower rose 125mm size with 225mm arm with swivel joints fixed in repairs as per Cat Part No.BS-73 of Prayag or technocommercial equivalent including fixing to steel pipe or union all as specified.

S&F, PVC connection 15mm bore size with two nuts and washers of length 450mm all as specified and approved.

S&F Cast iron branch pieces, single ( equal or unequal), ordinary or inverted (spigot or socket type) or with parallel branches, 100mm bore.

S&F 100mm bore cast iron bends any radius diminishing pieces or tapers (larger bore measured) complete all as specified.

S&F100mm bore sand cast, cast iron soil waste and vent pipes ISI marked in any length with or without ears with lead joints laid in floors or in trenches all as specified.

S&F Cast iron floor trap, dia of outlet 75mm with CI grating including jointing to waste pipe fixed in PCC M-15 (nominal mix) complete all as specified.

S&F 75mm bore cast iron bends any radius diminishing pieces or tapers (larger bore measured) complete all as specified.

S&F 75mm bore sand cast, cast iron soil waste and vent pipes ISI marked in any length with or without ears with lead joints laid in floors or in trenches all as specified.

S&F 50mm bore sand cast, cast iron soil waste and vent pipes ISI marked in any length with or without ears with cement joints fixed to walls all as specified.

Cast iron cowl suitable for pipes of 50mm bore.

Salt glazed stone ware gully traps, square mouthed, type 'P' 150mm x 150mm including excavation and earth work, set in PCC M-10(Nominal mix) block measuring jointing in cement mortar (1:1) all as specified.

Stack clamp out of 50mm by 5mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing of stays to wall or roof for 50mm bore pipe.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other frame/Chowkhat of size 45x70mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum , screw withdrawal strength of 2200N (Face) & 1100N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with properly of being termite/borer proof, water/moisture proof and fire retardant 152 Section 8 and fixed in position with MS hold fast/lugs/SS dash fasteners ofvrequired dia and length complete as per direction of Engineer-in-charge.

S&F prelaminated 18mm thick lead free factory made 100% solid WPC (wood polymer composite) sheet having high natural fiber content 25 to 30% wood colour sheets with density not less than 500 Kg/Cum and the weight of sheet of 1 sqm should be 11 Kg (+-5%) manufactured by ISO 9001-2015 certified company the sheet should be 100% water proof termite proof, fire retardent, manufactured by single layer extrusion process with excellent screw holding capacity and shore D hardness complete including all fittings like handle, hinges, hydraulic stopper, beading etc as per direction of Engineer-in-charge.

S&F in repairs 25mm dia stainless steel curtain rod fixed with stainless steel brackets & ornaments end cap fixed with screws,gutties etc design/ shape approved by Engr-in-charge complete all as specified and directed. .

M&L for treating the backfill in contact with foundation at the rate of 7.5 Lit of emulsion per square metre of vertical with backfill to be measured)

M&L for treating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre

M&L Treating the top surface of filled earth at the rate of 5 litres of emulsion per square metre of surface

M&L for 40mm thick cement concrete type B1, 1:2:4 (using 20mm graded crushed stone aggregate) finished even and smooth without using extra cement as in flooring, complete all as specified & directed. Note- Glass dividing strips shall be measured & paid separately as supply only

Supply only 38mm wide and 3mm thick glass dividing strips in flooring by fixing in position and making square or rectangle for casting concrete in flooring.

M&L for Providing cement concrete 1:2:4, type B1 (using 20mm graded crushed stone aggregate) mixed with water proofing compound as per manufacturer

M&L 200mm Reinforced concrete pipes, class NP-3, laid and jointed complete with collarsthick including demolition and breaking up drain pipes in cement mortar including demolition of PCC bedding and hunching complete all as specified and directed

M&L Concrete bed to drain pipes including packing under,and haunching against the sides of pipes after they are laid and tested in Cement concrete 1:4:8 type D-2 using 40 mm graded crushed stone aggregate for Bore of pipe in 200mm, complete all as specified and directed.

Material and labour for for precast reinforcement cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in landings, cover slabs (for manholes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces set in cement mortar (1:4) complete all as specified and as directed. Note:- Reinforcement shall be measured and paid separately).

S & F mild steel posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to, complete all as specified and directed.

Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars barred iron doors ladders; framed balusters; walk ways railings framework of water tanks, Square bars and similar work, complete all as specified and directed.

S&F galvanised 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured), complete all as specified and directed.

S&F for punched tape concertina coil of dia 410 mm (15 Nos round ) each coil to be streched to 6 mtr length secured and fixed in position having minimum tensile strength of 1620 N/Sqmm of specing steel core wire of size 2.6 mm, complete all as specified and directed.

M&L for broken glass coping on top of walls in cement mortar 1:3, complete all as specified and directed.

Forming V grooves in plaster n exc 10mm deep and n exc 10mm on face, complete all as specified and directed.

PVC (SWR) pipes 110mm dia single socketed in any length with rubber ring joints fixed to walls, complete all as specified and directed.

Hand packing (any thickness ) of broken stone or boulders at back of walls over arches etc and raising to the required level, complete all as specified and directed.

M&L for RCC pipe 450 mm dia NP-3 with PCC 1:3:6, complete all as specified and directed.

M&L for except boulder pitching is grouted with cement and sand mortar 1:6, complete all as specified and directed.

M & L for good quality dry sand cushioning to under ground electric cable on layer of 8 cm thick before laying the cable and second layer of 15 cm thick after laying the cable all as specified in clause 19.75 of MES Schedule part-I (2009) Note : Sand shall be fined sand as specifed and punned thickness shall be measured and paid.

Supply and laying sub class 'B' bricks of old size (230x115x75 mm) or of size locally available , laid along alignment of cable as protection to cable in trenches complete all as specified and directed by Engineer-in-Charge

M&L for point wiring with PVC insulated fire retardant stranded copper conductor cable of 1.5 sqmm in PVC concealed conduit heavy duty and pressed steel terminal boxes (for mounting switches /sockets/ regulators/ceiling roses etc ) made of not less than 16 gauge MS sheet and 6cm depth covered with 3mm thick laminated bakelite sheet fitted with brass screw and washers and drawing 1.5 sqmm PVC insulated fire retardant stranded copper conductor cable as earth continuity wire in green colour connected to common earth and each terminal box/fitting all as specified and directed by Engr-in-Charge (Phase Neutral and earth wire shall be provided in standard colour code R,Y,B for phase, Black for neutral green for earth wire). Note In ceiling Portion surface conduit wiring shall be carried out.

One light point or one fan point or bell point controlled by one switch SP one way 230 Volts.

One 3 pin socket out let 5/6 Amps on same board.

One socket out let 5/6 Amps on Independent board.

All as per srl item No 110.03 above but for 15/16 Amps socket out let independent with 4.0 sqmm copper conductor and.

M&L for switch Piano flush type single pole one way 5/6 Amp

M&L for switch,socket combination 2 in 1 , 3 pin, 5 and 15 Amp flush type all as specified and directed.

M&L for switch,socket combination 3 pin, 5 Amp flush type all as specified and directed.

M& L for bell push flush type 5/6 amp all as specified.

Supply and fix Buzzer Ding Dong, AC 230 volt single pole

M&L for socket outlet 2 in 1, 3 pin, 5 Amp flush type all as specified and directed.

Supply and fixing fan regulator electronic type with hum free snubber circuit with 4/5 steps 240 volts complete all as directed

M&L for ceiling rose 2-3 terminal size 65x20mm all as specified and directed.

S&F lamp holder Angle type insulated body with back plate for batten fitting, fixing with proper round block.

S&F for in replacement sheet metal enclosure with DB's (grouted in walls) double door type for MCB's 08 ways with 200 Amps 240 volts rated bus bar all as specified.

S&F in replacement existing unsv distribution board iron clad, double door with IP-43 1K-09 protection suitable for MCCB as incommer and MCB as outgoing 415 Volts 3 phase 50 C/s 4 way, complete with appropriate size copper bus bar and neutral link complete with one MCCB 3 pole 415 Volts 100 Amps rating with rupturing cap 16 KA of the same make as of distribution board & including cutting chases to wall for fixing DB and making good the disturbed wall surface all as required at site or directed by Engr-in-Charge

S&F for 6 to 32 amp MCB SP rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning and all as specified and directed

S&F for 32 amp MCB SPN, 50 C/S rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of following poles and current carrying capacity in the MCB DB complete with connection testing and commissioning and all as specified and directed

S&F for in replacement inverter type LED fitting 1x20W LED including LED tube 4 feet long having bipin holder, connector block etc complete all accessories prewired and connecting electrically to ceiling rose using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 sqmm 3 core all as required at site or directed.

S&F for in replacement existing UNSV decorative ultra slim square profile type fitting 4 feet long with LED tube light fitting 18 watt complete all accessories prewired and connecting electrically to ceiling rose using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 sqmm 3 core all as required at site or directed.

S&F for in replacement bldg security light fittings with LED security light fittings 35 watt, IP 65 having pressure die cast aluminium alloy housing, prismatic polycarbonate cover complete including making connection with 3 core copper flexible cable of suitable size including galvanised iron pipe bracket 0.90 mtr long of 25 mm dia and fixing with bldg for fixing of street light fitting all as directed.

Supply and Fix in replacement existing unsv decorative ultra slim square profilesleek LED mirror light fitting 2 feet long 1x10 W including LED tube 2 feet long of same make having ballast, bipin holder, connector block etc complete all accessories prewired and connecting electrically to ceiling rose using PVC insulated and overall sheathed flexible copper conductor cable of size 0.75 sqmm 3 core all as required at site or directed.

S&F inverter type LED Lamp 10 watt 230 volts complete all as specififed and directed.

S&F for sheet metal enclouser single pole and neutral with a 2 pin and earth plug and socket 20 A 240V complete with one single pole MCB of capacity 20 A complete all as specified and directed.

S&F for in replacement of ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. with brushless direct current motor (BLDC) without remote complete all as specified and as directed.

S&F for exhaust fan made of sturdy Engineering steel body with complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm complete all as specified and as directed.

M&L for Sub main wiring in PVC concealed conduit with 2 Nos single core PVC insulated copper conductor cable FRLS size 4 sqmm multistrand in concealed conduit with 4 sqmm PVC insulated FRLS as earth continuity wire using suitable size of copper thimble including provn of PVC coduit heavy duty ISI marked of adequate size.

M&L for Sub main wiring in PVC concealed conduit with 2 Nos single core PVC insulated copper conductor cable FRLS size 6 sqmm multistrand in concealed conduit with 6 sqmm PVC insulated FRLS as earth continuity wire using suitable size of copper thimble including provn of PVC coduit heavy duty ISI marked of adequate size.

Supply and lay cable XLPE insulated armoured heavy duty electric cable with aluminium counductor, 1100 volts grade of crosssectional area 16 Sq mm 2 core.Note: Earth work (Excavation, Returning & refilling and removal), sand cushining, cable protection cover, GI protection pipe shall be measured and paid for seperately under respective item of Schedule

Earthing complete with galvanised steel earth plate electrode, 600x600x 6.3mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised iron GI earth wire 4mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion

Supply, install, testing and commissioning of storage type electric water heater of 25 ltr capacity, BEE 5 star rated suitable for 8 bar pressure with nano polymer coated tank, incoloy heating element, rust proof ABS body etc complete all as specified and directed.(Note : Rate quoted deemds to be inclusive of anchor bolt, and pvc connetion) complete all as specifed and directed by Engr-in-Charge.

Note: In case the tenderer quotes different rates for similar item then lowest rate shall only be applicable for payment and contractor shall not have any claim on this account.

M/S Ajay Kumar Mahajan

Sandeep Kumar

VIJAY CONSTRUCTION CO

Jay Ann Construction Company

Mahajan Enterprises

jagdambe traders