SR TO TOILETS BLOCK OF CERTAIN OTM BLDGS (P-1, P-5 ETC) ,PROVN AND ADDN/ ALTN TO STROM/ RAIN WATER DRAINAGE AT CERTAIN PLACES ,PROVN OF WATER PROOFING TREATMENT AT CERTAIN BLDG ,and certain SANCTION AND MW AT AFS KHILLS UNDER GE AF THANE

Amount

Dismantling floor, paver block ,hearth or wall tiling including cement morter beddind (but not backing removing seviceable tiles to store and rubbish off the premises ,complete all as specified and as directed.

M&L for Glazed ceramic coloured (colour & shade as approved) tiles non skid of size 400x400x7mm thick as in floor set and jointed in neat cement slurry over and including 15mm thick screed in cement mortar (1:6) and pointed in white cement with pigment to match the colour of tiles complete all as specified.

All as per Srl Item No-02.00 hereinbefore but as on vertical surfaces such as skirting/dado over and including 10 mm thick rendering in cement mortar (1:4), complete all as specified.

M&L for Non-skid coloured ceramic (colour & shade as approved) tiles 7 to 8mm thick (Square/rectangular as per approved sample) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm in floor set and jointed in neat cement slurry over and including 15mm thick screed in cement mortar (1:6) and pointed in white cement with pigment to match the colour of tiles complete all as specified.

Material & labour for Glazed ceramic coloured tiles in vertical surfaces 450x350x7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over including 10 mm thick rendering in cement mortar (1:4) on fair faces of brick work or concrete surfaces complete all as specified and directed

Demolition of un-reinforced cement concrete in any position complete all as specified.

M&L for Cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in plinth protection, 50mm thick as in sub base, surfaces finished even and fair without using extra cement as in plinth protection including provision of construction joints ,complete all as as specified and as directed by Engr-in-Charge.

Demolition RCC Roofs, flors (other than ground floors), beams staircases, landing, chajjas, and similar suspended work ,complete all as as specified and as directed by Engr-in-Charge.

M&L for use & waste wooden form work (rough finished surfaces ) to sides & soffits of Chajjas, parapets & facia and similar work n. exc 200 mm thick,,complete all as as specified and as directed by Engr-in-Charge.

M&L for RCC type B1, 1:2:4 (20 mm graded Stone agg) as in Chajja, facia & RCC Slab etc.,complete all as as specified and as directed by Engr-in-Charge.

M&L for Mild steel TMT Mild steel bars 10mm dia and over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mmdia or securing with clips ,complete all as as specified and as directed by Engr-in-Charge.

Taking down wooden chowkhats or frames with shutters (without taking off shutters from the frames) of size not exceeding 1.50 Square metre each including cutting holes in brick walls of appropriate size for insertion of cement concrete blocks for hold fasts complete all as specified.

Taking down shutter of any description of exceeding 1 sqm but not exc 2 Sqm complete all as specified and as directed.

S&F Pressed steel frames made of 1.25mm thick MS sheet of profile 105x60mm for door and window frames with one rebate including lock strike plate, shock absorber, 20mm dia 60mm long MS conduit for housing of a drop bolt, treating of internal surfaces of chowkhats with coal tar or black paint including hinges, hold fasts/lugs etc complete all as specified.

M&L for Cement concrete (1:3:6), type C-1 using 20mm graded stone aggregate as in filling of steel chowkhats including necessary form work complete all as specified.

M&L for cement concrete (1:2:4) type B-I using 20mm graded stone aggregate as in drain surface channel, bed block ,coping,benching, sides of paver block and similar work incl. necessary form work complete all as specified.

S&F 35mm thick IInd class HW rail and style plain framed panelled factory made shutter (Two panel) with lock rail and panel of 9mm BWP,commercial ply or 12mm veneered particle beard with commercial veneering on both faces. The size of rail and stile as per IS :1003 (Part-I) kiln and chemically pressure treated , complete all as specified and as directed by Engineer-in-charge..

S&F Solid PVC door frame of size 50 mm x 47 mm made of 5 mm plain colour PVC sheet reinforced with mild steel square tube ,supplying and fixing in opening as per site specification and drawing shown in SSR Part-II ,complete all as as specified and as directed by Engr-in-Charge.

S&F for Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, supply and fixing in the frame at site specification and drawing shown in SSR Part-II ,complete all as as specified and as directed by Engr-in-Charge.

S&F for 150 mm Aluminium anodised, barrel tower bolts of ex truded section and fixed complete all as specified.

S&F for 75 mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified.

S&F for 100 mm Extruded aluminium alloy handles, fabricated type, anodised complete all as specified.

S&F anodised aluminium powder coated frame for doors,windows,ventilators with one or more rebated incl joining cleat for fixing etc. complete all as specified

S & F Anodised aluminium powder coated door shutters aluminimum section weighing 0.55 Kg/m incl necessary joining cleats glazing clips, rubber neoprene packing, handles 2 nos in each doors, hinges, anodiesed aluminium snap beading screw etc complete all as specified and directed.

S&F 5mm thick PVC plain colour PVC sheet in strips & channel feathered at the edges for fixing on Solid PVC Wall Linning, insulated PVC Wall Lining, and Solid PVC Partitions inclusive of solvent Cement and fixing at site complete all as specified and directed.

S&F 5.5 mm thick sheet glass, ordinary quality in Aluminium door with solar control film 50 micron in squares exc 0.5 sqm each pane complete all as specified.

S&F Brass mortice lock 100 mm,4 levers, vertical type, fixed to cupboard shutters, complete all as specified.

S&F Hydraulic door closer of aluminium die cast body,designation No-3 universal type suitable for door shutter of 851 mm to 1000 mm weight between 61 Kg to 80 kg etc, complete all as specified.

S&F Aluminium tower bolts powder coated , 150 mm long and fixed with steel screws, complete all as specified.

S&F 100mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-22 complete all as specified and directed.

M&L for Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket tc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

M&L for Powder coated aluminium (minimum thickness of powder coating 50 micron) work for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM Rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge.

M&L for Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved esign/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer in-charge.

S&F 4mm thick Sheet glass, ordinary quality and glazing with glazing clip and powder coated aluminium beading in square n exc 0.5 sq. m in each pane complete all as specified and directed.

S&F Stainless steel wire cloth 0.36mm nominal dia wire and average width of aperture 1.14mm and fixed with powder coated aluminium beading/wood beading complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden/ steel frames, glazed with putty or fixed with beads complete all as specified and directed

S&F 3 mm thick, plain sheet glass ordinary quality and glazing, with oil putty or with wooden beads, in squares n.exc 0.50 Sqm in each complete all as specified.

S&F for 150 mm Aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified.

S&F for 150 mm Extruded aluminium alloy handles, fabricated type, anodised complete all as specified.

S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

M&L for Preparation of new wooden or wood based surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified.

S&F Framed mild steel work of grade E-165 (Fe-290) as in framed work such as doors, gates or frame for cooler stand with gusset plates, rails, braces etc, drilled for fixing of sheeting or other covering of door etc, to be prepared for hanging or sliding etc including either hooks and hinges or steel hanging door fittings and hanging and fixing complete all as specified.

S&F Pre painted galvalume aluminum zink coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for Preparation of new steel surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified.

S&F PVC cabinet mirrors of size 550x400x75mm incl necessary shelves made of PVC sheets of minimum 5mm thick and mirror fixed on the front side of shutter complete all as specified and directed ( Make - Neelkamal, Prayag, Supreme)

Taking up or down existing steel water tubing, 15mm bore alongwith connections fixed/laid in any situation, complete all as specified.

Taking up or down existing steel water tubing, 20mm bore alongwith connections fixed/laid in any situation, complete all as specified.

Supplying and laying of CPVC pipes 20 mm outer dia of SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Supplying and laying of CPVC pipes 25 mm outer dia of SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

S&F for Brass Elbow of 20 mm outer dia complete all as specified and directed.

S&F for reducer Brass Elbow (3/4 X ½) of 20 mm outer dia complete all as specified and directed.

S&F for Female Brass Threaded Adaptor (FTA/ FBTA) of 20 mm outer dia complete all as specified and directed.

S&F Galvanised iron steel water tubing, 15mm bore, medium grade with all fittings and fixed to walls and ceilings or laid in floors complete all as specified.

S&F Galvanised iron steel water tubing, 20mm bore, medium grade with all fittings and fixed to walls and ceilings or laid in floors complete all as specified.

Fixing only, after cleaning old serviceable steel water tubing, 15mm bore and connections in new or old position using new fittings complete all as specified.

Fixing only, after cleaning old serviceable steel water tubing, 20mm bore and connections in new or old position using new fittings complete all as specified.

S&F, in repair, Towel rail, 19mm dia brass chromium plated, 600mm long with fancy type brass chromium plated brackets on both sides and fixed with steel screws and wooden/rawl plugs complete all as specified.

S&F, in repairs, PVC low level flushing cistern (white) of 10 liters capacity with inlet ball float valve, PVC flush pipe and necessary fixing arrangements and connecting to water pipe and WC etc and fixed complete all as specified.

S&F, in repair, 500 litres capacity rotational moulded, triple layer polythene water storage tanks (cylindrical vertical with closed top) hoisting and fixed in position on roofs including fittings & dismantling existing water storage tank, complete all as specified.

S&F 20mm bore PTMT ball valve high pressure with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed, complete all as specified.

S&F in repair stop cock 15 mm cast copper alloy screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe etc , complete all as specified.

S&F in repair Bib tap of CP brass, 15mm bore, fency type screwed down, screwed for iron pipe or for brass ferrule complete all as specified. .

S&F vitreous china squatting pan of pattern “Orissa Pattern” size 580 mm x 440 mm white with ‘P’ or ‘S’ trap, front or back inlet any pattern including provision of lime concrete bedding etc complete all as directed.

S&F ,in repair, Viterous China wash down water closet pan (pedestal pattern), white incl. Seat and cover (excluding fixing bolts, flushing cistern and flush pipe) complete all as specified and directed.

S&F Vitreous China urinals, Half Stall (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe ) , complete all as specified.

S&F Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) , complete all as specified.

S&F Vitreous China urinals, Full Stall (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe ) , complete all as specified.

S&F, in repair, Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position , complete all as specified.

S&F,in repairs,15mm bore stop valves of cast copper alloy, screwed down, high pressure with crutch or butter fly handle, fancy type, chromium plated, with long shank and cup (concealed type) fixed complete all as specified.

S&F Wash hand basin, flat back 550x400mm vitreous china (white) including PTMT waste fittings, 32mm bore size, waste pipe, PVC, 32mm bore, angle iron/cast iron brackets of required size complete all as specified.

S&F in repair 15mm bore pillar tap, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified.

S&F PVC connections 15mm size with PTMT nuts of length 450 mm etc suitable for 15mm bore of pipe complete all as specified.

S&F 50 mm Low density polyethelne (LDPE) pipes of pressure rating 6kgf/sq. cm complete all as specified.

S&F 125mm dia CP brass shower rose with swivel joints, any colour including shower arm 15mm dia, 195mm long with bend of 45 degree with flange of CP brass as in repair complete all as specified.

S&F for Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified.

Dismantling CI pipe alongwith fittings of 75/100mm dia, below or above ground level or laid in floors, jointed in cement mortar and taking out complete all as specified.

S&F 75mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified. (fitting measured separately).

S&F 75mm bore PVC (SWR) floor trap, plain with grating including jointing with solvent including jointing to waste pipe in run lead as in repairs complete all as specified.

S&F 75 mm bore PVC (SWR) branch piece, single (single Y) equal or unequal complete all as specified.

S&F 75 mm bore PVC (SWR) bends any radius complete all as specified.

S&F,in repair,110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to walls including distance pieces and stack clamps as in rain water pipes as complete all as specified.

S&F ,in repair,PVC (SWR) branch pieces, double 'Y' shape (equal or unequal) or with parallel branches 110 mm dia ,complete all as specified and directed by Engr-in-Charge.

S&F,in repair, PVC (SWR) junction, single 'T' (equal or unequal) 110 mm dia ,complete all as specified and directed by Engr-in-Charge.

S&F ,in repair, PVC (SWR) junction, double 'T' (equal or unequal) 110 mm dia ,complete all as specified and directed by Engr-in-Charge.

S&F 110 mm bore PVC (SWR) bends/shoe any radius fixed to walls including distance pieces and stack clamps complete all as specified.

S&F, in repair, grating doom 100 mm dia of PTMT (Minimum weight 25 gms) complete all as specified and directed.

S&F, in repair, grating doom 125 mm dia with waste hole of PTMT. (Minimum weight 40 gms) complete all as specified.

M&L for machine cut cudappa stone slab 20-25 mm thick over cement screed base as in jambs and soffits of lintel laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab incl rubbing and polishing including 10mm thick rendering in CM 1:3 ,complete all as specified ans directed by Engineer-in-Charge.

M&L for Surface preparation of non structural part by gentle chipping by manually to make the surface rough and thoroughly cleaned with air as per standard practice and directions of Engineer -in-charge (including removal of external plaster, wherever exists) COST inclusive of transportation, labour, conveying debris away from the out side of MD land, tools and tackles, lead and lift etc including necessery scaffolding ,form work etc, complete all as specified and as directed by Engr-in-Charge.

M&L for Providing and laying Renderoc SP-40 shrinkage controlled polymer modified single component, alkaline resistant fibre reinforced, thixotropic, cementitious patch repair mortor supplied in 25 kg moisture resistant bag when mixed with clean water at w:p ratio 0.18, achieves compressive strength (BS 1881 Pt. 116) -> 20 MPa at 1 day & > 45 MPa at 28 days. Tensile strength (BS 63199 Pt7)>2.5 Mpa at 28 Days, Flexural strength (BS 6319 Pt.3)>7 Mpa at 28 Days, During Shrinkage to ASTM C157-93, 28 days<1000 microstrain. Typical application inclues mixing entire bag with clean water about 4.25 ltr to 4.5 ltr, mixed with suitable container with heavy duty slow speed mixer machine to achieve lump free mortor consistency, placing and finishing the same with trowel carefully compacting the same around the rebars and finishing to bring it in line with existing concrete surface on the beams, slab, piles etc, where tha thickness of application is less then 50 mm in patch as per specification after applying bounding coat item rate is inclusive of materials all labour tools and tackles, scaffloding and transportation etc. complete as per specification and as directed by Engr-in-Charge.

Demolition of ashlar facings, dressed stonework, precast concrete articles and precast concrete block walling complete all as specified.

M&L for cement concrete (1:3:6), type C1 (using 20mm graded stone aggregate) straight or curved on plan exc 6 mtr mean radius, exc 10 cm width and set in CM (1:6) all as specified and as directed by Engr-in-Charge.

Taking down cement plaster or terrazzo from brick walls of any description, racking out joints, hacking for key, scrubbing down with water etc complete all as specified.

M&L for Rendering/plastering, 15 mm thick in cement mortar (1:4) on brick/block or concrete surfaces, surfaces finished even and smooth without using extra cement complete all as specified.

M&L for 15mm thick rendering in cement mortar (1:6) on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement complete all as specified.

M&L for 10mm thick rendering in cement mortar (1:3) on concrete surfaces, finished even and smooth without using extra cement as in ceiling complete all as specified.

M&L for preparation of newly plasterd surface of concrete or brick surfaces and applying Two coats ( having proportion @1.67 Litr/10 Sqm) of acrylic smooth exterior paint of required shade and including priming coat of exterior primer applied @ 2.20 Kg / 10 sqm, complete all as specified and as directed by Engr-in charge.

M&L for Preparation of newly plastered surfaces of walls & applying two coats of OBD on chalk whiting on plastered surfases complete all as specified.

M&L for Preparation of newly plastered surfaces of Wall & applying two coats coats of white wash complete all as specified.

M&L for Preparation of newly plastered surfaces of ceiling & applying three coats coats of white wash complete all as specified.

M&L for Preparation of old decorated surfaces of wall and applying one coat of white lime wash (white washing) on walls including corneces, pillars complete all as specified and directed.

M&L for Preparation of old decorated surface of wall and applying one coat of oil emulsion distemper complete all as specified.

M&L for Providing and applying plaster of paris putty of 1 mm thickness over plastered surface to prepare the surface even and smooth complete all as specified.

M&L for cleaning and preparation of old painted surface of wall apply one coats of weather proof paint camouflage pattern complete all as directed.

M&L for preparation of old surface of wall in any position washing down with water and cleaning the surface from all loose dirt, chalk, grease, fungal etc and finishing wall with one coat of weather proof acrylic paint etc ,complete all as specified and as directed by Engr-in-Charge.

M&L for Preparation of old decorated surfaces on ceiling and applying one coat of white lime wash including cornice and pillars etc complete all as specified.

M&L for Preparation of old painted wood or wood based surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for Preparation of old decorated surface of steel surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified.

Demolation of unreinforcement cement concrete of any description and in any position not otherwise specially provided for or as in Sunken complete all as specified

M&L Cement concrete (1:5:10) type E-2 using 40mm graded stone aggregate in foundations, filling and mass concrete, as in filling under sunken floor portion complete all as specified.

M&L APP modified polymeric membrane with mineral finish on top min 3 mm thick & weighing n. less than 3.5kgs/sqm with mineral reinforced with polyster non-woven fabric(wt n.less than 150gm/m2) laid over cold bituminous primer by torch application method with min overlap of 75mm on longitudinal direction & 100m in the transverse direction complete all as specified and directed.

M&L for Rendering/plastering, 10 mm thick in cement mortar (1:3) on concrete surfaces of sunken floor and applying bitumen blown any grade and applied two coats to concrete surface / rendering at the rate of 1.5 kg per sqm per coat and treating the sunken floor complete all as specified and directed.

Supply only integral water proofing compound complete all as specified.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation or for taking out/laying cable etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n.exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard/dense soil as specified and directed.

Demolition of brickwork or stone boulders masonry built in CM incl all quins, arches, pillers etc complete all as specified.

M&L Plain Cement concrete type C-2 (1:3:6) using 40 mm graded stone aggregate in surface channels and drains as specified and directed.

M&L for Pre-cast cement concrete block masonry Type C1 1:3:6 (20mm graded stone aggregate) with solid blocks, exc. 10 cm in width and set in CM 1:6 complete as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds,mitred/ stopped end etc complete all as specified.

Returning filling in including spreading, levelling, watering and well ramming in layers not exc 25 cm thick in soft / loose soil complete all as specified.

Removing excavated material exc. 250 m but n exc. 500 m and depositing where directed complete all as specified.

M&L for Concrete bed to drain pipes of 300 mm dia including packing under, and haunching against the sides of pipes after they are laid and tested; in cement concrete 1:3:6 type C2 complete all as specified and directed.

M&L for Reinforced concrete pipes, class NP2, 300 mm dia of pipe, laid and jointed complete with collars all as specified and directed .

M&L providing preast cement concrete type B1 1:2:4 (20mm graded aggregate) as in cover slab for drain etc. and setting in cement mortar 1:4 complete all as specified and directed. (Note : Reinforcement shall be measured and paid separately.)

S&F framed works such as grills gratings etc, with ends of bars shoulders and or reveted, or forged into spike framed guard bars barred iron doors ladders framed blusters, walk way railing , frame work of water tank and similar work con- forming Fe.290 Gde-E-165 all as specified and directed .

Surface excavation n.exc 30cm deep and averaging 15 deep and getting out in soft/loose soil complete all as specified.

M&L Hardcore of guage n.exc 63mm, deposited, spread and leveled in layers n exc 15cm thick, watered and rammed to a true surface in broken bricks all as specified and directed.

M&L for PCC 1:4:8 (using 40 mmgraded stone agg) type D2 as in foundation and sub base etc complete all as specified and directed.

M&L for chequered cement concrete tiles (reflective type) with mixture of white and grey cement in equal proportion and no pigments of size 30cmx30cmx25 mm thick, set, jointed and pointed in neat cement surry in floors including 20 mm thick screed bed in CM 1:6 for laying floor tiles complete all as specified and diected.

M&L for sand filling under floors or paving or in foundation or for cable protection etc including spread, levelled rammed and watering (as required) complete all as specified and directed.

Labour only (except tiles) for arranging existing serviceable machine pressed precast concrete inter locking paver block with grey cement and pigment (Reflective type) in any shape and size confirming to IS-15658-2006 of 60 mm thickness M-35 grade in proper levelling and other as specified and directed. (Note: existing serviceable paver block shall be used against this item, nothing shall be paid extra on this account).

M&L Machine pressed precast coloured concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with mixture of grey cement and pigment complete as specified and directed.

Excavating in post holes (or similar holes) each n exc 0.5cu.m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in hard/dense soil complete all as specified and directed.

M&L for cement concrete Type C2 1:3:6 (40 mm graded aggregate) in foundations, columns, pillars, post holes filling and mass concrete including caps and bases as specified and directed.

S&F Mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment complete (Fe-410W Gde-E 250 quality-A) all as specified and directed.

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S.1161-1979 grade St.-240 as specified and directed.

M&L for Pre-painted galvatume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified and directed.

M&L for Cutting chases, pinning in, making good to facings on stone concrete block or slab walls where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for inserting/concealed roofing sheets etc. and making good cutting exceeding 20cm girth as specified and directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified.

Removing existing water proofing treatment where so ever exist (except concretepadding) and removing debris/rubbish off the site as directed

Demolition of cement concrete of any description and in any position provided as in roof padding, roof curb etc complete all as specified and as directed. Note: - (a) Demolition should be done carefully to roof slab. (b) Any damage occurred in the roof surfaces during demolition shall be made good by the contractor without extra cost to the department. (c) Disposal of debris/retrieved materials shall be thrown out of site at place as directed.

M&L for providing PCC type B-1, (1:2:4) using 20mm graded stone aggregate as in roof padding laid in slope as per requirement mixed with integral water proofing liquid admixture as per manufacturer's instructions complete all as specified and as directed. Note: (i) Integral water proofing liquid admixture shall be measured and paid separately under appropriate item here in after

Supply only Liquid water proofing compound

Labour only of taking up or down steel tubing and connections of 20mm bore of pipe including cleaning and refixing in the same position as in wall/ roof /walls, etc during carrying out of water proofing treatment without damaging to existing services, etc. all as specified and directed.

Labour only of taking up or down steel tubing and connections of 25 to 32mm bore of pipe including cleaning and refixing in the same position as in roof /walls, etc during carrying out of water proofing treatment without damaging to existing services, etc. all as specified and directed.

Labour only for disconnecting existing over head tanks of capacity exc.500 and n.exc 1000 ltr, setting aside or lowering if required for repair of roof water proofing treatment and hoisting, reconnecting and re-fixing in position after necessary work without damaging to existing services etc. all as specified and directed.

Material and labour for water proofing treatment with APP based standard membrane over PCC padding in roof with the following courses of treatment for:- (a) Apply bituminous primer (IS 3384) @ 0.40 Kg per sqm of the surface area including cleaning the surfaces complete all as specified. (b) Apply APP plastomeric bitumen based mineral finished water proofing membrane polyester reinforced(3 Kg/Sqm) with 10cm over laps and torch bonded at joints including surface preparation before and after application of treatment as per manufactures instruction complete all as specified. (c) The entire surface of finished APP membrane shall finally be painted with one coat of Solar reflective bituminous aluminium paint @ 0.1 ltr per Square Meter and other as prescribed by manufacturer ,complete all as specified and as directed by Engr-in-charge.

S & F anodised aluminium snap grid frame work for false ceiling Size of grid 605 x 605mm incl hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified and directed.

S&F Non-combustible (Fire resistance) false ceiling board 4 mm thick as per Manufacturer instruction/ specification complete all as specified and directed.

M&L for point wiring with 1.5 Sqmm (nominal area) FRLSH insulated multi-stranded copper conductor confirming to IS 694 in and including Medium duty PVC casing capping (ISI marked) including fitting & accessories, with MS concealed terminal boxes with 3mm thick laminated BakeliteHylum sheet top cover for mounting switch, socket etc including 1.5 Sqmm stranded copper conductor with green PVC insulation earth continuity conductor 1.5 Sqmm connected to the common earth dolly and controlled by one switch ,complete all as specified and as directed by Engr-in-charge. of the following:-

One bell or buzzer point controlled by one push button on same board with other or independent switches

One Lightl/ceiling fan & exhaust fan point controlled by one switch .

One 3 pin socket outlet, 5 amps, on independent board

All as per Srl Item No 151.00 above but with 2.5 Sqmm for One 3 pin 16 amps socket outlet point controlled by one 16 amps switch on independent board

M&L of Sub-main Wiring with 2-Runs of 1.5 Sqmm (nominal area) 1100 Volt, PVC insulated unsheathed FRLSH multi-stranded Single Core Copper Conductor Cable and 1-Run of 1.5 Sqmm (nominal area) 1100 Volt, PVC insulated unsheathed FRLS multi-stranded Single Core Copper Conductor Cable (Green Colour) as Earth Continuty along with the Wiring drawn in CONDUIT/casing caping complete all as specified and as directed. Note : (i) Three length of wire along with conduit will be measured as one Length.

Supply and Fix and fix bell Buzzer,AC 230 volt single pole,complete all as specified and as directed by Engr-in-charge.

Supply and Fix Bell push button flush type 5 Amps ,complete all as specified and as directed by Engr-in-charge.

Supply & Fix switch piano flush button single pole one way 5 Amps, 230 V ,complete all as specified and as directed by Engr-in-charge.

Supply and fixing 5 Amps 3/5 Pin switch socket combination outdoor type with IP-65/66 protection complete all as speciified and directed.

S&F Ceiling rose, surface bakelite, 65mm x 50mm two to three terminals. ,complete all as specified and as directed by Engr-in-charge.

Taking down Exhuast fan, sealing cable end, dismantling blades and removing fan and blades to store complete all as speciified and directed.

S & F the Exhaust fan, steel body AC single phase, 230 volts size 300mm sweep with lower shutter including cutting hole and making good disturbed surface complete all as specified.

S & F the Ceiling fan, single phase, 230 volts size 1200mm sweep with provision of fan hook complete all as specefied.

S & F Distribution board, SP&N ,Prewired ,Netural links,blanking plates, double door 4 way, outdoor type with IP-65/66 protection, with provision for MCB SP&N as incommer and SP/DP MCB as outgoing and electrically connecting up ,complete all as specified and as directed by Engr-in-charge.

S & F MCB SP 6 to 32 Amps 240 volts 50 HZ having 10 KA ,complete all as specified and as directed.

S & F MCB SPN 40 Amps 240 volts 50 HZ having 10 KA ,complete all as specified and as directed.

Supply,laying, testing and commissioning XLPE insulated, screened, PVC bedded, galvanized strip or armored power cables (heavy duty) with stranded aluminium conductor ,1100 Volts grade underground cable of size 2 core 6 Sq mm complete all as specified and as directed.

Supply and laying un reinforced precast concrete cable cover class LV type-II, flat size 250mmx150mmx 40mm laid in trenches complete all as specified and directed by Engr-in-charge.

Supply and fix GI pipe 40 mm dia light grade complete with all fitting for cable supporting/protection complete all as specified and directed.

M&L for taking down carefully flat plate type solar water heater of Capacity 500/400 LPD after disconnecting incoming water supply, outlet chromium plated steel tubes hot water supply connection, air pipe,solar flat type collector plate (qty-04 Nos), hot water storage tank from the foundation. Refixing, testing commissioning of the plates ,solar hot water tank after complete cleaning of glass surface of plate and cleaning of storage tank and making connection of inlet and outlet steel tubings. Note :-(i)The cost of any brazing if required at site is deemed included in this item nothing shall be paid extra in this account. (ii) PCC/RCC for foundation, frame work for support of solar water heater shall be measured and paid separtely. (iii) Any damaged caused to flat plate collector or solar water heater storage tank, repair/replacement cost to be bear by contractor nothing shall be paid extra in this account.

M&L for Reinforced cement concrete (nominal mix) Type B1 1:2:4 (20 mm graded aggregate) in Foundations, including rafts,footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete all as specified and directed by Engineer-in-Charge.

M&L for insulation material for chromium plate steel outlet pipe of solar water heater as per recommended by manufacturer and all as specified by Engineer-in-Charge.

Taking down carefully copper/aluminium point wiring (light,fan,bell, socket or power) complete including fixtures and fittings such as switches, ceiling roses, holders,regulators, sockets, tube light fittings and making good disturbed surfaces of walls, floors etc to match with existing surfaces of colour shade complete all as specified and directed.

Supply & fix modular switch 6 Amps, one way, one module complete all as specified and directed.

Supply & fix modular switch 16 Amps,one way, one module complete all as specified and directed.

Supply & fix modular socket 6 A/16 Amps, 6 Pin combined, two module complete all as specified and directed.

Supply & fix in repair LED lights 1x20 watt ,220 V, AC decorative box type with driver , holder including LED tube light connecteing up with three core flexible copper conductor cable of suitable size from ceiling rose including connector block etc.and necessary fixing arrangement at any height and removing old unserviceable item complete all as specified and directed.

Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified.

M/s Qureshi Construction Co

Shree Gajanan Enterprises

Vinod Enterprises