8937-NIT-34-22-23 REPAIR TO SUNKEN FLOOR, PLUMBING SANITARY SOIL AND WASTE FITTINGS IN MD ACCN i.e. SHIVAJI ENCLAVE, PEERU SINGH ENCLAVE, BADLU SINGH ENCLAVE AND WATER SUPPLY ENCLAVE IN ZONE B AND N UNDER AGE BR III OF GE (N) BATHINDA AT BATHINDA MIL

Amount

SCHEDULE 'A' B/R Works

Demolition of cement concrete (unreinforced) in first floor, ground floor, sunken portion and paving at any thickness below or above floor level of any description and in any position including removing rubbish material from building and thrown in low lying empty area (as per direcction of AGE/JE) at any distance upto 500 metres from the site complete all as specified and as directed by Engineer-in-Charge

Material and labour for sunken treatment to sunken floor, cleaning the surface by wire brush, rendering to floor and sides with 10mm thick in cement mortar (1:3) including mixing of liquid WPC in mortar @ 200ml per bag of cement of 50kg, finished even and smooth without using extra cement, complete all as specified and as directed by Engineer-in-charge. NOTE:- (i) WPC for mixing in CM shall be measured & paid separately as Supply only.

Material & Labour for PCC (1:5:10) type E-2 using 40mm graded stone aggregate as loose filling of sunken floors complete all as specified and as directed by Engineer-in-charge.

Material and labour for 25mm thick cement concrete (1:2:4), type B-0 using 12.5 mm graded stone aggregate as in floor, sunken floor etc, finished rough to receive tiles, including mixing of liquid WPC in mortar @ 200ml per bag of cement of 50kg, complete all as specified and as directed by the Engineer-in-Charge. (Note :- WPC shall be measured & paid separately as Supply only)

Resecuring, easing and adjustments of shutters (any description and any size of shutter exc. 1 Sqm and not exc. 2 Sqm each) without taking down from chowkhat/frame including oiling, tigtening of screws, minor repairs, adjustment of hinges, adjustment of fittings like handle/tower bolt/door stopper etc complete all as specified and as directed by Engineer-in- charge. Note :- Screws if required for adjustment of fittings the cost of screws shall be included in the unit rate.

Demolition of brick work or stone / boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, in any description including cleaning and stacking serviceable brick for re use and balance removing rubbish from the site complete all as specified and as directed by Engineer-in-charge.

Material and labour for brick work with sub class ‘B’ old size burnt clay bricks, straight or curved on plan exc. 6 metre mean radius built in cement mortar (1:6) complete all as specified and as directed by Engineer-in-charge.

Demolition of floor hearth or wall tilling including cement mortar bedding but not backing including removing rubbish material from the site to a distance not exceeding 100 metre and deposited as directed complete all as directed by Engr-in-Charge

Material and labour for Non Skid ceramic coloured tiles 7 to 8 mm thick square or rectangular area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, as in floor set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement, tiles laid over and including 15 mm thick bedding layer (screed) in cement mortar (1:6) complete all as specified and directed by Engineer-in-Charge.

Material and labour for Glazed ceramic coloured tiles of size 350mmx 250mm / 450mmX 350mm// 450mmX 300mm, 7mm to 8mm thick, as in vertical surface set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile including necessary cutting as per site requirement, tiles laid over and including 10 mm thick (Av thickness) bedding layer (rendering) in cement mortar (1:4) complete all as specified and as directed by Engineer-in-Charge.

Demolition and cutting of floor tilling (broken tiles only as directed, without damage/demolition adjoining good tiles) area not exceeding 0.5 Sqm including cement mortar bedding layer and cleaning the area properly and removing rubbish material from the site and deposited as directed and after that fixing new non skid ceramic tiles to match with existing tile size and colour/sade, laid over and including 15mm thick bedding layer (screed) in cement mortar (1:6) and neat cement slurry, including pointed in white or coloured cement to match the shade of tile complete all as specified and directed by Engineer-in-Charge.

Demolition and cutting of wall tilling (broken tiles only as directed, without damage/demolition adjoining good tiles) area not exceeding 0.5 Sqm on vertical surface as in dados, skirting etc., including cement mortar bedding layer and cleaning the area properly and removing rubbish material from the site and deposited as directed and after that fixing new glazed ceramic tiles to match with existing tile size and colour/sade, fixing over and including 10mm thick bedding layer (plaster/screed) in cement mortar (1:4) and neat cement slurry, including pointed in white or coloured cement to match the shade of tile complete all as specified and directed by Engineer-in-Charge.

Material and labour for rendering/plastering appx 15mm thick (matching with existing plaster thickness) in cement mortar (1:6) on old brick or concrete surfaces of walls/pillars /cornices in patches matching with existing, finished even and smooth without using extra cement including old rusted plaster taking down, raking out joints, hacking for key and scrubbing down with water complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for rendering/plastering appx 10mm thick (matching with existing plaster thickness) in cement mortar (1:3) on any face of ceiling in patches matching with existing, finished fair and even and smooth without using extra cement including old rusted plaster taking down, raking out joints, hacking for key and scrubbing down with water complete all as specified and as directed by the Engineer-in-Charge.

Material and labour for rendering/plastering 15mm thick in cement mortar (1:4) on any face of Brick walls or concrete surfaces (external surface), finished even and smooth without using extra cement including old rusted plaster taking down, raking out joints, hacking for key and scrubbing down with water complete all as specified and as directed by the Engineer-in-Charge.

Supply & fixing in repair vitreous China squatting pan 'Orissa' pattern white of size 580mmx440mm white with integral foot rests and CI 'P' or 'S' trap (excluding flushing cistern, flush pipe above floor), including demolation of tile, PCC, taking out mass concrete filling and re filling PCC (1:7:12) type F2 after fixing of WC and trap with proper joints leakproof including PVC flush pipe upto finished floor level, and making good with 30mm thick cement concrete (1:2:4) type B0 finished rough as a sub base to recieved tile work and including all other connected work as required upto entire satisfaction of Engineer-in-charge complete all as specified and as directed by Engineer-in- charge. (NOTE : Tile work with screed and Sunken floor water proofing treatment shall be measured and paid separately under appropriate item of this schedule.

Supply & fixing in repair vitreous china wash down water closet pan (pedestal pattern, EWC) white clour (excluding flushing cistern and flush pipe) including connection to drain etc., including plastic water closet seat with cover (white clour) closed pattern with flat bottom and mild steel chromium plated or aluminised hinging device including stainless steel chromium plated jet spray with 01 mtr long PVC pipe with CP connector and necessary nut bolts and with necessary CP screws and plug for fixing WC complete all as specified and as directed by Engineer-in- charge.

Supply & fixing in repair vitreous china semi pedestal pattern (anglo indian type), white colour (excluding flushing cistern and flush pipe) including connection to drain etc., including plastic water closet seat with cover (white clour) closed pattern with flat bottom and mild steel chromium plated or aluminised hinging device including stainless steel chromium plated jet spray with 01 mtr long PVC pipe with CP connector and necessary nut bolts and with necessary CP screws and plug for fixing WC complete all as specified and as directed by Engineer-in- charge.

Supply & fixing in repair Plastic water closet seat cover, any colour, closed pattern with flat bottom, and mild steel chromium plated or aluminised hinging device complete all as specified and as directed by Engineer-in- charge.

Supply and fixing in replacement 10 litres capacity PVC valveless syphonic action type low level flushing cistern (white colour) with inlet, ball valve, float, handle including brackets and 32mm dia PVC flush pipe, PVC Connection 450 mm long with PTMT nuts suitable for 15mm bore pipe complete all as specified and directed by Engineer-in-Charge.

Supply and fixing hand shower (health faucet) ABS body including 1 meter long 8mm dia flexible tube and including wall hook including taking down old any type shower complete all as specified and as directed by Engineer-in-charge. Make :- Cat Part ALD-CHR-593N of Jaquar or equivalent (Equivalency approved by GE) in make mentioned in Appx A to PSS-II

Supply and fixing in replacement jet american JS-02, including pipe 1 mtr long with CP connecctor, fixing in EWC and to angle valve for water connection complete, all as specified and as directed by Engineer-in-charge.

Supply & fixing in replacement vitreous china wash basin, white, flat back of size 550mm x 400mm, including 32mm chromium plated waste coupling and PVC waste pipe including, supply & fixing of pillar tap, bracket and cutting for and pinning in end of bracket or erecting complete all as specified and as directed by Engineer-in-Charge.

Supply & fixing in replacement Bottle trap of PTMT having minimum water seal of 25mm and discharge pipe 32mm bore dia including necessary packing, union and cleaning cap and fixed complete all as specified and as directed by Engineer-in-Charge. Note :- The minimum weight shall be as given in SSR or in relevant IS.

Supply & fixing in replacement 32mm bore pipe Low density polyethylene pipes (LDPE) of pressure rating 6kgf/cm2 fixed complete to walls, ceilings or in floors etc. complete all as specified and as directed by Engineer-in-Charge.

Supply & fixing in replacement mixer valve 15mm bore, brass (cast copper alloy) chromium plated, mixer for mixing hot & cold water suitable for WHB or fixed to wall, screwed down for iron pipe 15mm bore complete all as specified and as directed by Engineer-in-charge. Note :- The minimum weight of mixer valve shall be as given in SSR or in relevant IS.

Supply and fixed in repairs flush kit of any type accessories with inlet ball valve float and handle complete all as specified and as directed by Engineer-in-charge.

Supply and fixing in replacement waste pipe (LDPE) and waste coupling, suitable for 32mm waste coupling, for sink/WHB, complete all as specified and as directed by Engineer-in-Charge.

Supply & fixing in replacement stainless steel sink made out of 1.00mm thick sheet, overall size 495mm x 420mm with bowl size 410mm x 330mm x 160mm, kitchen or laboratory with plugs, washers, waste pipe including bedding in cement mortar, fixing in existing space or fixing with cast iron cantilever brackets and connecting union to waste pipe, including taking down old unserviceable sink, complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in replacement stainless steel sink with drainage board made out of 1.00mm thick sheet, overall size 915mm x 460mm with bowl size 410mm x 330mm x 160mm, kitchen or laboratory with plugs, washers, waste pipe including bedding in cement mortar, fixing in existing space or fixing with cast iron cantilever brackets and connecting union to waste pipe; including taking down old unserviceable sink, complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in replacement Plate rack stainless steel for kitchen of Minimum size 24"x30"x10" Made out of not less than 1 mm thick SS Sheet including hanging material and including taking down old unserviceable plate rack, complete all as specified and directed by Engineer-in-Charge.

Supply & fixing rotational moulded polyethylene water storage tank white colour of capacity 500 litres (cylindrical vertical, triple layered with closed top), hoisted and fixed in position including making inlet and out let connection and fixing ball valve and gate valve including dismantling/taking down of existing unserviceable PVC water storage tanks of any description complete all as specified and as directed by Engineer-in-charge. (Note :- Float valve and gate valve shall be measured & paid separately as Supply only under appropriate item of BOQ.)

Cleaning and removing all scale and dirt, etc, from existing serviceable PVC tanks (OHT) of capacity upto 500 litrs without disconnecting or lowering, taking out mud from tank after proper drain out the water (manualy or mechanically ) including from mouths of circulating pipes etc. after cleaning checking all inlet and out let connections and tightening the same as required, Lid of tank refix properly complete all as specified and as directed by Engineer-in-charge.

Taking up or down existing galvanised steel water tubing (GI pipe)/ PVC KITEC 15mm bore including fitting/connection from wall/ceiling/floor/concealed etc. including removing from site/keeping aside for reuse (serviceable as good condition as directed) complete all as specified and as directed by Engineer-in-charge.

Taking up or down existing galvanised steel water tubing (GI pipe) / PVC KITEC 20mm bore including fitting/connection from wall/ceiling/floor/concealed etc. including removing from site/keeping aside for reuse (serviceable as good condition as directed) complete all as specified and as directed by Engineer-in-charge.

Taking up or down existing galvanised steel water tubing (GI pipe) / PVC KITEC 25mm bore including fitting/connection from wall/ceiling/floor/concealed etc. including removing from site/keeping aside for reuse (serviceable as good condition as directed) complete all as specified and as directed by Engineer-in-charge.

Supply and fixing galvanized steel tubing (GI pipe) medium grade 15mm bore ISI marked with all new fittings like elbow, tee, union, socket, reducer etc. and fixed complete to walls, ceiling and laid in floor or concealed in walls including cutting chases in wall (as required) and making good disturbed surfaces of walls including cutting and threading of existing pipe any dia for insertaion of tee branch including hole in wall to pass the pipe out side for connection as per site requirment complete all as specified and as directed by Engineer-in- charge.

Supply and fixing galvanized steel tubing (GI pipe) medium grade 20mm bore ISI marked with all new fittings like elbow, tee, union, socket, reducer etc. and fixed complete to walls, ceiling and laid in floor or concealed in walls including cutting chases in wall (as required) and making good disturbed surfaces of walls including cutting and threading of existing pipe any dia for insertaion of tee branch including hole in wall to pass the pipe out side for connection as per site requirment complete all as specified and as directed by Engineer-in- charge.

Supply and fixing galvanized steel tubing (GI pipe) medium grade 25mm bore ISI marked with all new fittings like elbow, tee, union, socket, reducer etc. and fixed complete to walls, ceiling and laid in floor or concealed in walls including cutting chases in wall (as required) and making good disturbed surfaces of walls including cutting and threading of existing pipe any dia for insertaion of tee branch including hole in wall to pass the pipe out side for connection as per site requirment complete all as specified and as directed by Engineer-in- charge.

Re-fixing old serviceable 15mm bore galvanised steel water tubing (GI pipe) including all fittings like elbow, tee, union, socket, reducer etc. in new or old portion/position to walls, ceiling and laid in floor/concealed in walls etc and making good disturbed surfaces of walls complete all as specified and as directed by Engineer-in-charge. (Note :- Old serviceable pipe and fittings obtained from taking up or down (here-in-before) item of this BOQ shall be reused after necessary cleaning internally.

Re-fixing old serviceable 20mm bore galvanised steel water tubing (GI pipe) including all fittings like elbow, tee, union, socket, reducer etc. in new or old portion/position to walls, ceiling and laid in floor/concealed in walls etc and making good disturbed surfaces of walls complete all as specified and as directed by Engineer-in-charge. (Note :- Old serviceable pipe and fittings obtained from taking up or down (here-in-before) item of this BOQ shall be reused after necessary cleaning internally.

Re-fixing old serviceable 25mm bore galvanised steel water tubing (GI pipe) including all fittings like elbow, tee, union, socket, reducer etc. in new or old portion/position to walls, ceiling and laid in floor/concealed in walls etc and making good disturbed surfaces of walls complete all as specified and as directed by Engineer-in-charge. (Note :- Old serviceable pipe and fittings obtained from taking up or down (here-in-before) item of this BOQ shall be reused after necessary cleaning internally.

Supply & fixing in replacement 450 mm long PVC connection 15mm size with PTMT nuts complete all as specified and as directed by Engineer-in-charge.

Supply and fixing in replacement brass bib tap, with crutch or butterfly handle with capstan head, screwed down, screwed for iron pipe or for brass ferrule 15mm bore complete all as specified & directed by Engineer-in-charge. Note :- The minimum weight shall be as given in SSR or in relevant IS.

Supply and fixing in replacement bib tap cast copper alloy, chromium plated fancy type, long body with crutch or butterfly handle with capstan head, screwed down, screwed for iron pipe or for brass ferrule 15mm bore complete all as specified & directed by Engineer-in-charge. Note :- The minimum weight shall be as given in SSR or in relevant IS.

Supply and fixing in replacement stop valve/angle valve cast copper alloy, chromium plated fancy type screwed down high pressure with crutch or butterfly handle, screwed both ends suitable for 15mm bore iron pipe complete, all as specified & directed by Engineer-in-charge. Note :- The minimum weight of stop valve/stop cock/angle valve shall be as given in SSR or in relevant IS.

Supply & fixing in replacement pillar tap cast copper alloy with capstan head, chromium plated, fancy type, high pressure with or without letter 'Hot' or 'Cold' with long shank and fly nuts screwed for iron pipe or for brass ferrule 15mm bore complete, all as specified & directed by Engineer-in-charge. Note :- The minimum weight of tap shall be as given in SSR or in relevant IS

Supply & fixing in replacement brass cromium plated shower rose 125mm size, with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and as directed by Engineer-in-charge.

Supply & fixing in replacement brass chromium plated/stainless steel tubular towel rail 20mm dia 'D' type, 600mm long between flanges fixed to plug , bracket with chromium plated brass screws all as specified and directed by Engineer-in-Charge.

Supply and fixing in replacement ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball (polythene float) complete, screwed suitable for 20mm bore iron pipe complete all specified and as directed by Engineer-in-charge. Note :- The minimum weight of ball valve shall be as given in SSR or in relevant IS.

Supply and fixing in replacement ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball (polythene float) complete, screwed suitable for 25mm bore iron pipe complete all specified and as directed by Engineer-in-charge. Note :- The minimum weight of ball valve shall be as given in SSR or in relevant IS.

Material & Labour for 100 mm bore cast iron soil waste and vent pipe (spun pipe ) in any length with or without ears, fixed to wall with stack clamps (interval of 1m) made out of FI 50x5mm and 16mm dia round iron stay and jointing with cement mortar including dismantling/taking down/out old pipe complete all as specified and as directed by Engineer-in- charge.

Material & Labour for 75 mm bore cast iron soil waste and vent pipe (spun pipe ) in any length with or without ears, fixed to wall with stack clamps (interval of 1m) made out of FI 50x5mm and 16mm dia round iron stay and jointing with cement mortar including dismantling/taking down/out old pipe complete all as specified and as directed by Engineer-in- charge.

Material & Labour for 100 mm dia cast iron floor trap with CP grating including jointing to waste pipe with solvent fixed in cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate including taking out old floor trap complete all as specified and directed by Engineer-in-Charge.

Material & Labour for 75 mm dia cast iron floor trap with CP grating including jointing to waste pipe with solvent fixed in cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate including taking out old floor trap complete all as specified and directed by Engineer-in-Charge.

Supply & fixing in replacement 100mm bore cast iron bends (any radius)/elbo, diminishing pieces or tapers (larger bore measured) with oval access door fixed with cement joints complete all as specified and as directed by Engineer-in- charge.

Supply & fixing in replacement 75mm bore cast iron bends (any radius)/elbo, diminishing pieces or tapers (larger bore measured) with oval access door fixed with cement joints complete all as specified and as directed by Engineer-in- charge.

Supply & fixing in replacement 100mm bore CI branch pieces single (equal or unequal), ordinary or inverted (Spigot or socket type) or with parallel branch fitted with oval access door as specified & directed by Engineer-in- charge.

Supply & fixing 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall, including taking down old unserviceable pipe, complete all as specified and as directed by Engineer-in- charge.

Supply & fixing 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall, including taking down old unserviceable pipe, complete all as specified and as directed by Engineer-in- charge.

Supply & fixing for PVC (SWR) bends 110mm bore any radius, complete all as specified and as directed by Engineer-in- charge.

Supply & fixing PVC (SWR) junction single, (Single T) equal or unequal suitable for 75mm bore pipe fixed to walls or laid in floor complete all as specified and as directed by Engineer-in- charge.

Supply & fixing ir repair Stainless steel CP grating round or circular 125mm dia with or without waste hole complete all as specified and as directed by Engineer-in-charge.

Supply and fixing in repair PVC (KITEC) straight coupler compression 16mmx20mm for PVC compression pipe of dia 16/20 mm complete all as specified and as directed by Engineer-in-charge.

Supply and fixing in repair PVC (KITEC) Tee 3 side coupler composite compression 20mmx20mm for PVC compression pipe of dia 20/25 mm complete all as specified and as directed by Engineer-in-charge.

Supply and fixing in repair PVC (KITEC) elbow one side coupler and one side threaded composite compression 16mmx20mm for PVC compression pipe of dia 16/20 mm complete all as specified and as directed by Engineer-in-charge.

Supply and fixing in repair PVC (KITEC) Tee 2 side coupler one side threaded composite compression 16mmx20mm for PVC compression pipe of dia 16/20 mm complete all as specified and as directed by Engineer-in-charge.

Supply and fixing in repair PVC (KITEC) elbow both side coupler composite compression 16mmx20mm for PVC compression pipe of dia 16/20 mm complete all as specified and as directed by Engineer-in-charge.

Supply and fixing GI PVC (KITEC) water tubing, medium grade, 15mm bore ISI marked with all fittings and fixed to wall and laid in floor complete all as specified and as directed by Engineer-in- charge.

Supply and fixing GI PVC (KITEC) water tubing, medium grade, 20mm bore ISI marked with all fittings and fixed to wall and laid in floor complete all as specified and as directed by Engineer-in- charge.

Supply only liquid water proofing compound complete all as specified and as directed by the Engineer-in-Charge. Make : Dr Fixit/Fosroc/BASF/STP

Material and labour for preparation of new plastered surface and newly plaster in patch works on surface of walls/pillars /cornices by brooming down with using broom/sand papering or by any other mean, washing down with water and applying two coats of cement base paint as per approved tint/colour with using paint brush complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparation of new plastered surfaces of walls/pillars /cornices by brooming down with using broom/sand papering or by any other means, and preparing the surfaces smooth by applying white cement based putty to make the surface even and smooth by using sander machine (with provision of dust sucking) upto entire satisfaction of Engineer-in-charge, and after preparing the surfaces applying two coats of oil bound distemper (washable), as approved tint/colour by using paint roller brush complete all as specified and as directed by Engineer-in-Charge.

Material and labour for preparing newly plastered and newly plaster in patch works on surface of ceiling by sand papering or by any other mean and after preparing the surfaces applying three coats of white wash complete all as specified & directed by Engineer-in- charge

AGGARWAL CONSTRUCTION CO.

M/s DHEERAJ JAIN CONSTRUCTION COMPANY

M/s Kamal Builders

M/S VIAJY BUILDERS & DEVELOPERS