DEMOLITION AND RECONSTRUCTION OF BOUNDARY WALL AT CSD DEPOT AT BRICHGUNJ MILITARY STATION UNDER GE BRICHGUNJ PORT BLAIR

Amount

Rough excavation not exceeding 1.5m deep and getting out in hard dense soil complete all as specified and directed.

Excavation in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, etc or not exceeding 10 Sqm on plan and not exceeding 1.5m in depth for shafts, cesspits, manholes, pier holes, etc and getting out in hard dense soil complete all as specified and directed.

Excavation in trenches, exceeding 1.5m wide and not exceeding 3.0m in depth for foundation, etc or not exceeding 10 Sqm on plan and not exceeding 3.0m in depth for shafts, cesspits, manholes, pier holes, etc and getting out in hard dense soil complete all as specified and directed.

Returning, filling in excavated approved soil, including spreading, levelling, watering and well ramming in layers not exceeding 25cm each complete all as specified and directed.

Removing excavated soil to a distance not exceeding 50m and depositing where directed. at a level not exceeding 1.5m above the starting point complete all as specified and directed.

M&L PCC 1:3:6 type C2, using 40mm graded aggregate as in foundation concrete including demolition complete all as specified and directed..

S&F Mild steel TMT bars 10mm dia and over as reinforcement for concrete, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

S&F Mild steel TMT bars 5 to 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L for RCC M-30 using 20mm graded stone aggregate as in Foundations, footings, foundation beams; plinth beams; bases for columns, etc including demolition complete all as specfied and directed. Note:- Rate shall be inclusive of removal of debris and deposition at low lying area outside MD premises.

M&L for RCC M-30 using 20mm graded stone aggregate as in columns, pillars, piers, posts, beam and struts etc including demolition complete all as specfied and directed. Note:- Rate shall be inclusive of removal of debris and deposition at low lying area outside MD premises.

M&L for RCC M-30 using 20mm graded stone aggregate as in beams, cantilevers, bressummers, lintes over 1.5m span including demolition complete all as specfied and directed. Note:- Rate shall be inclusive of removal of debris and deposition at low lying area outside MD premises.

Use & waste of Form work to sides & soffits of lintels over 1.5m clear span, floor or roof beams, cantilevers, etc for fair finished flat surfaces of concrete complete all as specified and directed.

Use & waste of Form work to sides of square or rectangular columns, pillars, posts and struts for fair finished surfaces of concrete complete all as specified and directed.

Use & waste of Form work to sides of concrete foundations, footings, bases of columns, sides & soffits of foundation and plinth beams and similar work for fair finished flat surfaces of concrete complete all as specified and directed.

M&L Precast cement concrete type C1 1:3:6 (20mm graded agg) block masonry with solid block exc 10cm in width and setting in CM 1:6 complete including demolition all as specified and as directed.

M & L rendering 10mm thick in CM 1:4 on other than fair face of brick work or concrete surfaces to be finished fair and even smooth without using extra cement complete all as specified and as directed.

M&L Preparation of newly plastered surfaces of wall & applying Two or more coatsof 100% Premium acrylic emulsion paint havingVOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance,dirt resistance exterior paint of required shade(Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces over a coat of putty complete all as specified and directed.

M&L PCC 1:2:4 type B1, using 20 mm graded aggregate as in coping etc., including necessary formwork and demolition complete all as specfied and directed. Note:- Rate shall be inclusive of removal of debris and deposition at low lying area outside MD premises.

M&L cement concrete Type B1 1:2:4 using 20mm graded stone aggregate as in Bed blocks and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specfied and directed.

S&F Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as direced.

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 including dismantling complete all as specfied and directed..

S&F in repairs Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured)

S&F Concertina coil fencing with Punched Tape Concertina Coil made from High Tensile Spring Steel, High Carbon Wire conforming to IS-4454 [Part-1], of Grade-SM duly Hot Dipped Galvanised as per IS-4826 with 230GSM, 600mm dia, 10 Metre openable length, with Galvanised coating and Punched Tape material as per IS-513, having 50Nos Rounds per 6 Metre Length [before stretching], having medium barbs [barb Length 24±1mm, Barb Width 19±1mm, Pitch between Two Barbs 35±1mm], Spring Core wire [2.6mm thick] of high tensile strength of 165Kg/Sq.mm with tape [0.522mm thick] and weight 43.478Grams/Metre and fixing "Y" or Trapezoidal shaped angle iron brackets placed at 2.00m to 3.00m apart and with 6/9 horizontal RBT [Reinforced Barbed Tape] Wire, Stud tied with GI staples and GI clips to retain horizontal including necessary bolts and coating with Px Compound [Anti Rust] complete all as specified and directed. Note Horizontal Barbed Wire & angled iron supports shall be measured and paid seperately.

M&L Painting two coats of synthetic enamel paint over a coat of red oxide including preparation of new steel surfaces of any description over 10cm in width or girth not other wise described complete all as specified and directed.

A N KUMAR

Gulmarg Electrical Service

M/s Karbhagam Sales Agency

M/s Kamal Electrical

DEEPAK AGENCIES

RS ENGINEERING WORK

Nirman Construction Company

P Babu