Providing LIS to Okhoo in GP Lug da Ghat in Tehsil Ramshehar District Solan HP

Amount

Cutting in earth work and disposal of excavated earth in all lead and lift in all kind of soil.

Excavation in foundation trenches upto all depths in all classification of earth work such as pick work,jumper work, saturated soil including bailing of pumping out water,blasting soft/hard rock where blasting is prohibited.In all lifts including trimming and dressing of sides,levelling of beds to correct grade i/c shoring,strutting,planking timbering and dewatering wherever required,stacking the usable and un-useable material / soil separately and after laying, jointing of pipes returning the useable soil in trenches in trenches in 15 cm (fifteen centimeters) layers including consolidating of each of each deposited layer by ramming and watering and disposing of all surplus excavated soil un useable materials as directed within all leads & lifts including restoration of un-metalled surfaces to its original condition and including cost of diverson for traffic night signals, fixing caution boards, crossing over trenches for excess to houses, fencing etc.complete in all respect with in all leads & lifts as per the direction of the Engineer-in-charge.

Excavation in drain and channels etc. earth work for pipes upto all depths in all classification of earthwork such as pick work, jumper work, saturated soil including bailing or pumping out water, blasting soft/hard rock or chiseling soft/hard rock where blasting is probihited in all lifts including jungle clearence wherever required, trimming & dressing of sides, levelling of beds to correct grade including shoring/struting, planking , timbering & dewatering wherever required stacking the useable/unuseable material/soil seperately & after laying, jointing & testing of pipes, returning the useable soil in trenches in 15cm layers including consolidating of such deposited layer by ramming & watering & then disposing of all surplus excavated soil/ unuseable material as directed with in all leads & lifts including restoration of un-metalled surfaces to its original condition & including cost of diversion for traffic, right signals, fixing caution boards, crossing over trenches for acess to houses, fencing etc. complete in all respect with in all leads and lifts and as per direction of the Engineer-in-charge at site of work.

Providing and laying cement concrete 1:6:12 ( I cement : 6 sand : 12 graded stone aggregate 40mm nominal size ) and curing complete excluding the cost of form work in foundation and plinth including carriage of material in all leads & lifts.

Providing and laying cement concrete 1:4:8 ( I cement : 4 sand : 8 graded stone aggregate 40mm nominal size ) and curing complete excluding the cost of form work in foundation and plinth including carriage of material in all leads & lifts.

1st classBrick work using common burnt clay building bricks in foundation and plinth in cement mortar 1:6(1cement:6sand)

Providing and laying damp proof course 38mm thick with cement concrete 1:2:4(1cement : 2 sand :4graded stone aggregate) 12.5mm nominal size) and curing complete.

Providing and laying cement concrete work 1:1.5:3(1cement:1.5 sand :3 graded stone aggregate 20 mm nominal size)and curing complete excluding cost of form work and reinforcment for reinforced concrete form work and reinforcement for reinforced concrete work in i/c carriage of material within all lead and lifts

Flat surfaces such as slab etc.

In walls(any thickness but not less than 0.10m thickness,) partitions and string courses and like

Applying a coat of hot bitumen(mexphalt 80/100 or equivalent) using 1.70Kg.per square metre on damp proof course after cleaning the surface of cloth lightly soaked in kerosene oil.

Frist class brick work using common burnt clay building bricks in supper structure in all heights and depth in cement mortar 1: 6 (1cement:6sand)

Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm so as to give a fair finish including centring,shuttering,struting and propping etc with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 mtrs. and removal of the same for insitu,reinforced concrete and plain concrete and plain concrete work in :-

Flat surfaces such as slab, soffits of suspended floors, roofs, landings and the like.upto 200 mm thickness .

Vertical surfaces such as walls (any thickness but not less than 0.10m thick) partitions and the like including attached pillasters buttresses, plinth and string courses and the like

Providing and laying cement concrete work 1:2:4(1cement:2sand: 4 water borne aggregate 20mm nominal size & curing complete excluding the cost of form work and reinforcement for reinforced concrete work in suspended floors, roofs, landing shelve and their supports balconies beams, girders bressumers and centilevers upto floor two level.

Providing & Placing Tor steel reinforcement for RCC work i/c bending,binding and placing in possition complete including bending wire upto floor all level including carriage of material in all leads & lifts

15mm cement plaster in single coat in rough side of brick/stone masonery for interior plastering upto floor two level including arrises,internal,founded angles,chamfers and/or rounded angles chamfers and/or rounded angles not exceeding in girth & finished even and smooth in cement mortar 1:5(1cement:5sand).

Pointing on brick work with cement mortar 1:3(1cement:3sand) ruled pointing.

Providing and fixing pressed steel door frames manufactured from commercial MS sheets of 1.25mm thickness including hinges, jump lock jamp. Bead and if required angle threshold of MS angle 50 x 25 mm or base tie of 1.25mm pressed MS welded or rigidly fixed together by mechanical means, adjustable lugs with split and tails to each jamp i/c steel butt hinges 2.5mm thick with guards, lock strike plate and shock as specified and applying a coat of steel primer after pretreatment or surface as directed by Engineer-in-charge.

Profile---"A"

Profile---"B"

Providing and fixing 1mm thick M.S.sheet door with frame of 40mmx40mmx6mm angle iron 3.15mm M.S. gusset plate at the junctions and corners including all necessary fittings, complete including applying a priming coat of red lead paint.using flat 30mm x6mm for diagonal braces and control cross/pieces.

Filling in plinth with sand under floors including watering ramming consolidating and dressing complete.

Providing and laying cement concrete flooring 1:2:4 (! cement:2 sand:4 water borne aggregate 20mm nominal size laid in one layer finished with a floating of neat cement 40mm thick.

P/F on wall face PVC rain water pipe i/c fitting and complete in all respect.

White washing with lime on undecorated wall surface(two coat) to give an even shade i/c throughly brooming the surface to remove all dirt,dust,mortar dirt and other foreign matter.

Hirmachi colour wash on decoated wall surfaces(Three coats) to give an even shade i/c thoroughly brooming the surface to remove all dirt,dust mortar drops and loose scale of hirmachi wash and other foreign matter.

Providing plinth protection 50mm thick in cement concrete 1:3:6(1cement:3sand:6water borne stone aggregate 20mm nominal size)including finishing the surface of concrete smooth.

Painting two coats(excluding priming coat)on new steel work based surfaces,with ready mixed paint,brushing to give an even shade including cleaning of all dirt,dust and other foreign matter,sand papering and stopping,with paint other than white.

Providing and fixing aluminium tower bolts(berral type)anodized transparent or dyed to required shade and colour with screws etc. complete (250 x 16) complete i/c carriage of materials with in all leads and lifts.

Providing and fixing M.S fan clamp type-I of 16mm dia M.S bar bent to shape with hooked ends in RCC during laying including printing the expossed portion of loop, all as per standard design complete.

P/F MS grills of required pattern in wooden frames/pressed steel frame with M.S.flat square/round bars 12mm dia with round headed bolts and nuts or by screws Plain grill complete i/c carriage of materials with in all leads and lifts.

Providing and fixing C.I Man hole cover pre-tab cement manhole cover with frame complete i/c carriage of materials with in all leads and lifts.

Providing ,Laying ,jointing and testing of galvanised MS pipe 65 mm dia CI Vent & scour pipe complete in all respect.

Providing ,Laying ,jointing and testing of galvanised MS pipe 100mm dia for scour complete in all respect.

Providing & fixing M.S. gate of angle iron and flat 6 mm thick with frame I/c locking arrangment andplacing in position complete i/c carriage of materials with in all leads and lifts.

Finishing wall with water proofing cement paint of approved brand and manufacture and of required shade on undecorated wall surfaces (two coats) to give an even shade after thogoughly brushing the surface to remove all dirt and remains of loose powered materials.

Wiring for light/Fan point/Exhaust fan point/call bell point with 1.5 Sq.mm PVC insulated heat resitant flame retardent (HRFR) and low smoke single core (flexible) copper conductor cable in PVC casing and capping and earthing the light point with 1.5 sq.mm HRFRLS /PVC insulated single Group "C" as required including carriage of all material within all leads and lifts.

Wiring for light/power plug with 2 x 4 Sq.mm PVC insulated heat resistant flame retardent (HRFR)and low smoke single core (flexible ) copper conductor cable in PVC casing and caping along with 1 no, 4sq. mmHRFRLS/PVC insulated single core copper as required including carriage of materials within all leads and lifts.

Wiring for light/power plug with 4 x 4 Sq.mm PVC insulated heat resistant flame retardent (HRFR)and low smoke single core (flexible ) copper conductor cable in PVC casing and capping along with 2no, 4sq. mm HRFRLS/PVC insulated single core copper as required including carriage of materials within all leads and lifts.

Wiring for light/power plug with 2 x 1.5 Sq.mm PVC insulated heat resistant flame retardent (HRFR)and low smoke single core (flexible ) copper conductor cable in PVC casing and capping along with 1 no, 1.5 sq. mmHRFRLS/PVC insulated single core copper conductor cable as required including carriage of materials within all leads and lifts.

Wiring for circuit / sub main wiring with 4 x 1.5 Sq.mm PVC insulated heat resistant flame retardent (HRFR)and low smoke single core (flexible ) copper conductor cable in PVC Casing & capping along with 2 no, 2.5sq. mm(4x2.5+2x2.5) HRFRLS/PVC insulated single core copper conductor cable as required including carriage of materials within all leads and lifts.

Supplying and fixing metal box of 100 x 100 x 60mm deep (Nominal size) on surface/recess with suitable size phonolic leminated sheet cover fixing 3 pin 15/16 amps socket tumber/piano type switch connections painting etc. including carriage of materials within all leads and lifts

S/F of 6amps to 32 amps rating 10 KA breaking capacity ,240 Volts, "C" curves miniature circuit breaker of following poles in the existing MCB DB complete with connections testing and commissioning etc. as required including carriage of materials within all leads and lifts Category -A single pole.

Supplying and fixing 40 Amps/50 amps / 63 Amps rating 10 KA breaking capacity 240 Volts "C"curves miniature circuit breaker of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required including carriage of material within all leads and lifts.Double pole Category- B 63 Amps.

Supplying and fixing of following way single pole and neutral sheet steel MCB distribution board 240 volts,on surface/recessed complete with tinned, copper busher neutral link, earth bar, din bar, detachable gland plate, interconnections, including painting, earthing etc. as required : Single door 8 way.

Providing, installing, testing and commissioning of 25 LED Light (categary "A" including wiring with 1.5 Sq mm PVC insulated copper conductor single core cable etc.as required .

Providing, installing, testing and commissioning of ceiling fan and regulator including wiring the rod of standard length(upto 30 cm) with 1.5 Sqmm PVC insulated copper conductor single core cable etc.as required 1200 mm sweep Category A.

Providing, installing, testing and commissioning of 1x36 watt -FTL (T8) shock proof slim (categary "A" including wiring with 1.5 Sq mm PVC insulated copper conductor single core cable etc.as required .

Earthomg woth G.I pipe earth, pipe 4.5 mtrs length, 40 mm dia including acessories and providing masonary encloures with cover plate having locking arrangement and watering pipe, (but without charcal coke and salt complete as required including carriage of material within all leads and lifts.

Extra using salt and charcoal for pipe earth electrode as required including carriage of material within all leads and lifts.

Supplying and laying 6 SWG (4mmdia) G.I wire on surface or in recess for loop earthing alongwith exisint surface/recessed conduit sub main, as required including carriage of material within all leads and lifts.

Supplying and fixing wall mounted metal board welding construction fabricated with minimum 25mm x 25mm x3mm angle framed work with 20mmx3mm steel iron as intermediate no, including painting etc. as required including carriage of material within all leads and lifts.

Rising Main:-Providing, Laying,jointing testing & commissioning at site in trenches bevelled ended BIS marked galvanized MSERW pipes confirming to IS/ISO 3188/2019 latest with upto date ammendments of following dia with steel grade A or L-210, having wall thickness & per rmt weight as mentioned below & capable of withstanding required test pressure as prescribed in BIS code , in randum lengths of 5.5 to 6.5 mtrs. The pipe ends shall be bevelled suitable for butt welding, including the cost of jointing with butt welding confirming to IS 816-1969 or latest as applicable ends with upto date ammendments ( leak Proof ) in three layers at site of work with welding roads of standard make & all allied acessories whatever required for welding at site, tail pieces tees,bends & other specials manufactured from parent pipes as applicable to the particular reach & of approved specification as per site condition and cutting of pipes wherever required as per site requirement i/c carriage in all leads & lifts The pipe shall have zinc coating inside & outside confirming to IS- 4736-1986 or latest with upto date ammendments & shall be engraved with YST - 210, code IS- 1978 or its equivalant. The laying shall confirm to BIS 5822-1970 or latest with upto date ammendments to the entire satisfaction of the Engineer-in-charge( Earth work shall be measured & paid for seperately ) .

From To Nominal Dia Thickness Class Grade

Booster Stage

0 90 200 mm 4.80 MSERW A or L-210

Main Stage

0 120 200 mm 5.60 MSERW A or L-210

120 360 200 mm 5.20 MSERW A or L-210

360 1460 200 mm 4.80 MSERW A or L-210

Providing, welding and fixing M.S plate flanges of 200mm dia (Nominal bore) of following flange Table conforming to BIS specification No. 6392-1971 or latest with upto date ammendments to pipe after every 100 Jointsr or as per site requirement including cutting of pipes wherever required, welding in three layers (leak proof) confirming to specification as per prescribed in relevant IS Code i.e IS 816-1969 or latest as applicable with upto date ammendments with nuts, bolts & washers & specials etc. confirming to IS-1963 or latest with upto date ammendments including packing sheet i.e asbestos fibre sheet minimum 3mm thick and painting with anticrossive paints complete in all leads,lifts and carriage of material at site and as directed by the Engineer-in-charge.

From To Nominal Dia Flange Table

Distribution System of HDPE Pipe:- Providing,Laying, jointing,with butt fusion welding testing and commissioning of high density polyethylene pipe for use in buried water main and services and for water supply below ground , duly ISI marked ( IS-4984-1995) as amended upto date of grade PE 80 & of class PN 4.0 ,PN 6.0 & PN 8.0 of the following diameter,i/c cost of fitting, bends ,Tees other jointing material etc complete in all respect. (Earth work work to be measured and paid for separately) complete in all respect, including entire carriage of materials upto all leads and lifts and as per direction of Engineer-in-Charge.

HDPE pipe 140 mm dia PN 4.0 PE 80 IS:4984

HDPE pipe 140 mm dia PN 8.0 PE 80 IS:4984

HDPE pipe 160 mm dia PN 4.0 PE 80 IS:4984

HDPE pipe 160 mm dia PN 6.0 PE 80 IS:4984

HDPE pipe 160 mm dia PN 8.0 PE 80 IS:4984

Pumping Machinery -Mono SUBMERSIBLE :-Supply, errection, testing &commissioning of star rated enrgy efficient Mono Submersible pumping set of KSB/Calama/ WPIL/ Crompton/BS/ SABAR / Oswal/ Kirloskar or any other approved make conforming to latest relevant BIS Code 8034:1976. The pump should be fitted with bronze impeller or suitable alloys suitable for handling Clear water having greased packed bearings and shaft with wound stator on motor side and with soft protection sleeve on pump side ensuring better life for shaft coupled to a submersible squirrel cage electric induction motor (water proof type) of required HP & 2900/1450 rpm of reputed make conforming to BIS 9283-1979 latest with upto date amendments, totally dust and water proof for submersible duty isolated from the pump by intermediate casing with double mechanical seal in oil chamber and grease packed lubricated bearings and provided with stainless steel thrust bearing plate to with stand non vertical loads with minimum wear and tear. It should also be fitted with a device to take up expansion of water with the heating of motor. The pump set should include water level guards, erection clamps , cable clips, depth gauge NRV & Sluice valves of approved class etc. The work should be completed to the entire satisfaction of the Engineer-in – Charge. The HP are indicative, the design /drawings of Pumping Machinery is to be got approved by L-1 Contractor from the competent authority before placing supply order for the same after finalisation of tender.The rates shall be for complete Job to run the machinery in proper working. The pumping machinery & its accessories/ valves /piping work etc. should meet with the following requirements. (i) Sluice Valves/Reflux Valves to be provided on delivey line:- These shall be double flanged valves of approved make & size of valves shall be same as dia of R-main.The class of valves shall be of cast iron PN-1.6 (ii) Power shunt Capactor:- Capacotors shall be of suitable KVAR so as to improve power factor to 0.95 or above. (iii) Pannel Board:- It shall be of suitable size & capable to accomodate all above electrical accessories i/c providing & fixing in position these accessories & interconnections with cable of appropriate size & specifications. (iv) Startes:- Starters shall be of approved make & of suitable rating suitable of safe running and operation of given motor or pumping machinery It shall be mounted on panel board with magnetic type over load release & dashpot, time lag,under voltage release with initial oil filling if required. (Detailed requirement of P/M & its allied accessories electromachnical components & valves etc. shall be as per design data sheet no1)

Booster house :- 1 set (1 working ) for duty condition discharge of = 23.94 LPS with Total Head of = 36.70 mtr. The BHP is to be offered by the bidder & rate shall be filled in by the contractor per set. )

CENTRIFUGAL PUMING MACHINERY (SUMP WELL TO D/TANK):- PUMPING MACHINERY CENTRIFUGAL:- Supply ,Installation ,Testing & Commissioning of star rated energy efficient horizontal spindle, horizontal/ radial split casing/end suctions (back pull out arrangement)single/ double/ multistage centrifugal pump suitable for operation, in parallel of recommended make such as Mather and platt/ KSB/Kirloskar/Jyoti /Beaconweir BS&BE or any other approved make confirming to BIS-1520-1980 with upto date ammendments, read with IS:9137-1978 or latest edition suitable for lifting clear water for under mentioned characteristics with bronze/Bronze with 2.5% Nickel impellers, dia of 405mm priming funnels, casing ring and shaft sleeves of bronze/ steel, shaft of SS:410/AIS 1431 Chrom in plated with cast iron casing coupled directly through a flexible coupling on a Common MS base plate to squirrel cage screen protected drip proof induction motor/TEFC/CACA of standard make such as Kirloskar/BHEL/ Crompton/NGEF/GEC/ Siemens / Jyoti/Area Brown Boven (ABB)/CGL and suitable for operation on 11 KV HT, 50 cycles/second 3 phase AC electric supply. The power of electric motor/motors should be at least (+) 10% in excess of the maximum power required by the pump / pumps in the operation range of (+) 10% and (-) 15% of the duty point head. The motor/ motors should be as per IS: 325-1978 with upto date amendments read with IS:900-1972. The starting current of the motor shall be limited to not more than 4.5 to 5 times of full load current.

It should include cost of bearing nuts, bolts and painting etc and should meet the following requirement including Pump sets (working + standby), All electrical equipments such as Starter, ICTP switches, MCB, Bush bar chamber, MCB, Panel board indicating lamps, Ammeter, Voltmeter, Hour run meter should be of electronic type , incoming and outgoing water proof cable for panel board, Double loop earthing, copper cable pressure gauge, capacitor, common header, sluice valve, NRV including erection and testing complete necessary piping for suction and common header and control valves alongwith electrical works including all taxes, insurance, transportation, freight charges, inspection charges, loading, unloading, conveyance to Departmental stores/ site, stacking, etc. including specials and wastage etc.; complete as per Tender Specifications and instruction of Engineer in charge. The HP are indicative, the design/drawings of Pumping Machinery is to be got approved by L-1 Contractor from the competent authority before placing supply order for the same after finalisation of tender. The rates shall be for complete Job to run the machinery in proper working. The pumping machinery & its accessories/valves/piping work etc. should meet with the following requirements. (i) Sluice Valves/Reflux Valves to be provided on delivey line:- These shall be cast steel double flanged valves of approved make & size of valves shall be one size higher than delivery size of offered pump.The class of valves for stage cast steel ASA-300 . (ii) Reflux Valves to be provided in Rising Main:- It shall be be double flanged cast steel valve of approved make & size of valve shall be same as dia of rising main pipe. The class of valve shall be Cast steel ASA-300 (iii) Piping work (Common Header, Delivery pipes & Suction pipes):- The piping work shall be of same specifications as the R-main in intial RD's. The size of common header shall be same as dia of R-Main. in No case pipe wall thickness shall be less than 4.80 mm. The common header & delivery pipes shall be properly jointed with flanges of appropriate Flange table with butt welds. (iv) Power shunt Capactor:- Capacotors shall be of suitable KVAR so as to improve power factor to 0.95 or above. (v) Pannel Board:- It shall be of suitable size & capable to accomodate all above electrical accessories i/c providing & fixing in position these accessories & interconnections with cable of appropriate size & specifications. (vi) Startes:- Starters shall be of approved make & of suitable rating suitable of safe running and operation of given motor or pumping machinery It shall be mounted on panel board with magnetic type over load release & dashpot, time lag,under voltage release with initial oil filling if required. ( Detailed requirements of P/M & its allied accessories electromechnical components valves etc shall be as per design data sheet no 1)

Sump well to D/tank - 1 set (1 working ) for duty condition discharge of = 23.94 LPS with Total Head of = 218.40 mtr. The BHP is to be offered by the bidder & rate shall be filled in by the contractor per set.)

AMAR SINGH GOVT CONTRACTOR

puneet angra

chirag seth

Anurag Deep

Bharat Panwar

Vijay Kumar