Providing Road Safety Arragements at CTC Medu New bus stand in Pollachi Municipality

Providing and Laying of hot applied Thermoplastic compound 2.5mm thick including reflectorising glass beads@ 250 gms. per sqm.area, thickness of 2.5mm.is exclusive of surface applied Glass Beads as per IRC: 35 The finished surface to be level, uniform and free from streaks and holes etc. Complete as per MORT & H specification No.803.

Providing and erecting of retro reflectorised Hazard Marker Traffic sign made out of high intensity prismatic grade sheeting confirming to type IV standards of IRC 67-2012 and ASTM D4956-09, Specification and fixed over 2mm thick aluminum sheet fixed over a back supporting frame of 25mm x 25mm x 3mm mild steel angle and supported on mild steel angle iron post 75mm x 75mm x 6mm and 0.60m below ground level. The sign post should be painted as per IRC 67-2012 and firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cm x 45cm x 60cm size including cost and conveyance of all materials, equipment, Machinery and Labour with all Leads and lifts, Loading charges necessary for satisfactory completion of the work as directed by the engineer in charge. High intensity Retro- Reflector sheet shall consist of Minimum coefficient of retro – Reflection as per Table 6.6 of IRC 67-2012.The retro-reflective sheeting shall be covered under 7 years warranty issued for field performance and a certified copy of three years outdoor exposure report shall be obtained as per IRC 67-2012(as per MORTH specification no 801)

Providing and fixing of retro reflectorised cautionary mandatory and informatory signs (without definition board) made out of high intensity prismatic grade sheeting confirming to type IV standards of IRC 67-2012 and ASTM D4956-09, Specification and fixed over 2mm thick aluminum sheet fixed over a back supporting frame of 25mm x 25mm x 3mm mild steel angle and supported on mild steel angle iron post 75mm x 75mm x 6mm with a clear height not less than 2.10m from the ground level to the bottom of the sign board and 0.60m below ground level. The sign post should be painted as per IRC 67-2012 and firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45cm x 45cm x 60cm size including cost and conveyance of all materials, equipment, Machinery and Labour with all Leads and lifts, Loading charges necessary for satisfactory completion of the work as directed by the engineer in charge. High intensity Retro- Reflector sheet shall consist of Minimum coefficient of retro – Reflection as per Table 6.6 of IRC 67-2012.The retro-reflective sheeting shall be covered under 7 years warranty issued for field performance and a certified copy of three years outdoor exposure report shall be obtained as per IRC 67-2012(as per MORTH specification no 801) (90cm Stop Board )

Providing and fixing reflective road studs of category A Raised pavement markers made out of poly carbonate/methyl methercrylate/Abs Moulded body confirming to ASTM D 788 and reflective panels with micro prismatic lens capable of providing total internal reflection of the light entering the lens face with retro-reflectance and chromaticity values conforming to ASTM D 4280. The Reflective raised pavement markers shall also confirm to the MORTH circular No RW/NH. 33023/10/97-DO.III dt 11.06.97 and the height, width and length shall not be less than 15mm,90mm and 100mm and with minimum reflective area of 13 sq.cm on each side and the slope to the base shall be 35+/- 5 degree. Each reflector shall have a CIL not less than values Specified in Table 2 of said MORTH circular. The Strength of detachment of the integrated cylindrical shanks,(of diameter not less than 19*/- 2mm and Height not less than 30*/- 2mm) from the body is to be a minimum value of 500kgf.Fixing will be drilling Holes on the road for the Shanks to go inside,without nails and using epoxy resin based adhesive as per manufacturer's recommendation and complete as directed by the engineer.The marker Shall support a Load of 13635kg tested in accordance with ASTM D4280 and confirming to IRC 35 - 2015 guidelines and MORTh Specification 804 etc.,complete

Supplying and installation of delineators (road way indicators,hazard markers and object markers) 80-100cm high above ground level,painted at alternatively black and white in 15cm wide strips,fitted with 80 x 100mm rectangular or 75mm dia circular reflectorised panels at the top,buried or pressed into the ground and confirming to IRC-79 etc.,complete(as per MORTH specification No .806

GST18%