Loading
Loading…
New
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope, Go/No-Go checksEligibility, required documents, scope of work and Go/No-Go checks for this tender, in one click.
Tender Value
₹94.8 L
EMD Value
₹1.9 L
Closing Date
19 Nov 2026, 12:00 pm
Eligibility, documents, scope, Go/No-Go checksEligibility, required documents, scope of work and Go/No-Go checks for this tender, in one click.
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
90 days
Expenditure
Capital (Works)
ELECTRICAL
15 conditions · 4 needing a document upload
The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less ; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB of GCC-April-2022 along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
The tenderer shall posses the valid Electrical Contractor's license and Supervisory License issued by any State/Central Govt. licensing board for the required voltage level or above with their tender paper. Tenders without valid electrical contractor's license & Supervisory license will summarily be rejected.
The tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i) Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii) One similar work costing not less than the amount equal to 60% of advertised value of the tender.
Definition Of Similar Work : - 1.Erection of LT or above voltage level distribution panels. OR2.Erection and commissioning of LT or above voltage level line (over head or underground.)3.Electrification/Rewiring of service building bungalow and quarters. OR4.Supply and erection of tower light. OR5.Lighting of station/Administrative building/Circulating area.
32 conditions · 6 needing a document upload
Scanned copy of PAN (Permanent Account Number) and Goods and Services Tax Registration Certificate indicating GSTIN should be uploaded. In case of non-availability / non-applicability of any of these documents, reasons should be furnished under 'Remarks'. GSTIN along with other details required under CGST/SGST/UTGST/IGST Act may also be submitted by the successful tenderer immediately after the award of contract.
Scanned copy of EPFO registration certificate and ESIC registration certificate should be uploaded along with tender offer.
In case the tenderer is a partnership firm, an undertaking by all partners of the firm shall be uploaded in compliance to clause no.18.11(iii) of Tender Form (Second sheet) in the prescribed format as per Annexure-10 of the attached document with description 'Formats to be Used'. In case the tenderer is a Sole Proprietorship Firm / HUF / Registered Company, an undertaking shall be uploaded in compliance to clause no.14 (ii)- (a) / (b) / (e) of Tender Form (Second sheet) in the prescribed format as per Annexure-11 of the attached document with description 'Formats to be Used'. In case the tenderer is Registered LLP, an undertaking shall be uploaded in compliance to clause no.14 (ii)- (f) of Tender Form (Second sheet) in the prescribed format as per Annexure-12 of the attached document with description 'Formats to be Used'.
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Attested copies of the documents pertaining to constitution of the concern (Sole Proprietorship Firm / Partnership Firm /Registered Company/ Registered Trust / Registered Society /HUF etc.) as described in detail at clause no.14 of Tender Form (Second Sheet) of GCC 2022 as well as legal competency of the person signing the tender offer (Power of Attorney) should be uploaded clearly indicating the nature of the firm. Power of attorney shall be submitted even if the person signing on behalf of the tenderer is authorized for that purpose through partnership deed / Memorandum of Understanding / Article of Association or such other document, failing which tender is liable to be rejected. Sole proprietorship firm shall have to submit notarized copy of the affidavit. In case the tender is signed and submitted by the proprietor himself /herseIf, no power of attorney is required. Railway reserves the right to legally scrutinize original copies of such documents as and when required. After opening of the tender, any document pertaining to the constitution of Sole Proprietorship Firm / Partnership Firm / Registered Company/ Registered Trust / Registered Society / HUF etc. shall be neither asked nor considered, if submitted. Further, no suo moto cognizance of any document available in public domain (i.e., on internet etc.) or in Railway's record/office files etc. will be taken for consideration of the tender, if no such mention is available in tender offer submitted.
The tenderer will have to make payment towards Earnest money deposit (EMD) against this tender through online payment modes like net banking, debit/ credit cards etc. available on IREPS portal (www.ireps.gov.in). The tenderer is required to pay the Earnest Money deposit before he can prepare and submit his bid. Any firm recognized by Department of Industrial Policy and Promotion (DIPP) as 'Startups' shall be exempted from payment of Earnest Money on submission of Registration Certificate issued by appropriate authority. 100% Govt. owned PSUs shall be exempted from payment of earnest money deposit. Labour Cooperative Societies shall deposit only 50% of above earnest money deposit on submission of necessary documents.
In support of their credentials, the Tenderers should submit along with their tenders document - List of Plant and Machinery available on hand (own/hired) and proposed to be inducted (own/ hired) to be given separately for the subject work .
The Earnest Money and Cost of tender booklet : There is one mode for submssion of EMD through online payment. The bidders will have to make payment towards tender document cost and earnest money against the tender through online payment modes like net banking, debit/ credit cards etc. available on IREPS portal in favour of FA & CAO, ECR, Hajipur payable at Hajipur executed by State Bank of India or any of the Nationalized Banks or Scheduled Bank.
Eligibility criteria for works tender in respect of partnership firms:-
in case the tenderer is a partnership firm s , the experience, solvency and turn over shall be in the name and style of the firm only.
If the tenderer is a partnership firm, all the partners shall be jointly and severally liable for successful completion of the work and no request for change on the certification of the firm shall be entertained.
During the currency of the contract, no partner of the firm shall be permitted to withdraw from partnership business and in such and event it shall be treated as breach of trust and abandonment of the contract.
JOINT VENTURE will not be permitted for the tenders.
Any Conditional offer will be summarily rejected.
Rates are inclusive of all taxes/GST, license fee, royalty charges etc. legally leviable by State, Central Govt. and/or any other local authority.
Earnest Money and Tender Document Cost: -All the tenderers / Contractors have to deposit full earnest money and tender document cost as stipulated in the tender document through online modes as permitted in IREPS application.
After opening of the tender, any document pertaining to the constitution of Sole Proprietorship Firm / Partnership Firm / Registered Company/ Registered Trust / Registered Society / HUF etc. shall be neither asked nor considered, if submitted. Further, no suo moto cognizance of any document available in public domain (i.e., on internet etc.) or in Railway's record/office files etc. will be taken for consideration of the tender, if no such mention is available in tender offer submitted.
Tenderers shall note that the submission of supporting documents at the time of on line bidding of tender, is important and they shall ensure the same. However Railways may seek clarification/details/documents in this regard.
Before submitting the offer, please read carefully complete e- tender document including annexed document, Standard General Condition of Contract. Special Condition of Contract, bill of quantities etc. Your digital signature on the etender form will be considered as your confirmation that you have read and accepted all the condition laid down in the document stated above.
This contract shall be governed by "Indian Railways General Condition of Contract, April-2022" which is uploaded with up to date correction slips (if any).However, tenderers need not upload the same along with their bid. Tenderers are responsible for knowledge of GCC and its amendment.
Electrical work in connection with work "At Narkatiaganj - Development of second entry with circulating area.
EL-G-SPJ-36-ET-26-27~ECR
EL-G-SPJ-36-ET-26-27
Open
Works - General
180 Days
Samastipur, Bihar
₹0
₹1.9 L
27 Oct 2026
27 Oct 2026
5 Nov 2026
131 items across 1 schedule
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | 94,79,606.14 | ||
| — | 700.00 | — | — | ||
| Wiring for light point/fan point/exhaust fan point/call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface/recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. copper cable/wire make - Havells, Finolex, Anchor,Polycab,KEI.PVC pipe make - Malhotra, Bansal, Jyotiplast,Simplex. | — | — | — | 3,15,133 | |
| — | 480.00 | — | — | ||
| Wiring of 5 amp. point single core 2x1.5 sq mm copper wire on platform surface trusses including supply and fixing of ceiling rose board, fuse kitkat, indicator and connection etc with all other accessories complete in all respect. PVC board make - Cany/classic/Harson. Ceiling rose fuse kit-kat, Indicator make - Havells, HPL, Cona. | — | — | — | 78,408 | |
| — | 3540.00 | — | — | ||
| Wiring of sub-main Concealed/ surface(Normally concealed) in heavy gauge 2 mm PVC conduit pipe with single core PVC insulated multi strand copper conductor cable 2 x 2.5 sq. mm multi strand (36/0.3 No./Nominal dia of wire in mm.)for phase and neutral and 1 X 2.5 Sq. mm cable for earth. The colour coding of cable red for phase, black for neutral and green for earth must be maintain .The rates per meter includes PVC pipe 1 meter length and 03 nos 1 meter copper wire with other accessories, if more than two wires are required to be drawn for other circuit than higher size pipes are to be used or separate pipe as required as per site requirement. copper cable/wire make - Havells, Finolex, Anchor,Polycab,KEI. PVC pipe make -Malhotra, Bansal, Jyotiplast, Simplex. | — | — | — | 3,50,566.2 | |
| — | 1600.00 | — | — | ||
| Wiring of sub main concealed / surface (Normally concealed) in heavy gauge 2 mm PVC conduit pipe with single core PVC insulated multi strand copper conductor cable 2 x 4 sq.mm multi strand (56/0.3 No./Nominal dia of wire in mm.) for phase and neutral and 1 x 4 Sq. mm cable for earth. The colour coding of cable red for phase ,black for neutral and green for earth must be maintained. The rates per meter includes PVC pipe 01 meter length and 03 nos 1meter copper wire with other accessories. If more than three wires are required to be drawn for other circuit than higher size pipes are to be used or separate pipe as required as per site requirement. copper cable make - Havells,Finolex, Anchor, Polycab,KEI', R R Kabel. PVC pipe make - Malhotra, Bansal,Jyotiplast,Simplex. | — | — | — | 1,82,160 | |
| — | 800.00 | — | — | ||
| Wiring of sub main concealed / surface (Normally concealed) in heavy gauge 2 mm PVC conduit pipe with single core PVC insulated multi strand copper conductor cable 2 x 10 sq.mm multi strand (56/0.3 No./Nominal dia of wire in mm.) for phase and neutral and 1 x 10Sq. mm cable for earth. The colour coding of cable red for phase ,black for neutral and green for earth must be maintain. The rates per meter includes PVC pipe 01 meter length and 03 nos 1meter copper wire with other accessories. If more than three wires are required to be drawn for other circuit than higher size pipes are to be used or separate pipe as required as per site requirement. copper cable/wire make - Havells,Finolex, Anchor,Polycab,KEI. PVC pipe make -Malhotra, Bansal, Jyotiplast, Simplex. | — | — | — | 1,74,240 | |
| — | 15.00 | — | — | ||
| Supplying and fixing of 15/16 A modular switch on the existing modular plate & switch box including connections but excluding modular etc. as required. Make - Havells,Anchor, Cona. | — | — | — | 2,316.6 | |
| — | 15.00 | — | — | ||
| Supplying and fixing of 6 pin 15/16 A modular socket outlet on the existing modular plate & switch box including connections but excluding modular etc. as required. Make - Havells,Anchor, Cona. | — | — | — | 2,925.45 | |
| — | 4.00 | — | — | ||
| Supplying and fixing of 1 or 2 Module(75 mm x75 mm) GI box along with modular base & cover plate for modular switches in recess etc.as required Make - Cona/Havells/Anchor. | — | — | — | 903.4 | |
| — | 6.00 | — | — | ||
| Supplying and fixing 3 module(100 mm x 75mm), GI box along with modular base & cover plate for modular switches in recess etc. as required Make - Cona/Havells/Anchor. | — | — | — | 1,472.1 | |
| — | 8.00 | — | — | ||
| Supplying and fixing 4 module(100 mm x 75mm), GI box along with modular base & cover plate for modular switches in recess etc. as required Make - Havells, Anchor, Cona | — | — | — | 1,982.64 | |
| — | 10.00 | — | — | ||
| Supplying and fixing of 6 Module (200mmx75mm) ,GI box along with modular base & cover plate for modular switches inrecess etc. as required. Make - Havells,Anchor,Cona. | — | — | — | 3,046.7 | |
| — | 4.00 | — | — | ||
| Supplying and fixing 8 module (125 mm x 125mm), GI box along with modular base & cover plate for modular switches in recess etc. as required Make - Havells, Anchor, Cona | — | — | — | 1,376.36 | |
| — | 4.00 | — | — | ||
| Supplying and fixing of 12 Module (200mmx200mm) ,GI box along with modular base & cover plate for modular switches inrecess etc. as required. Make - Havells,Anchor,Cona.. | — | — | — | 1,658.28 | |
| — | 10.00 | — | — | ||
| Supplying and fixing suitable size GI box with modular plate and cover in front on surface orin recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16A modular switch, connections etc. as required. Make - Havells, Anchor, Cona. | — | — | — | 4,441.3 | |
| — | 50.00 | — | — | ||
| Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3/5 pin5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required. Make -Havells, Anchor, Cona. | — | — | — | 17,895 | |
| — | 245.00 | — | — | ||
| Installation, testing, commissioning and Supply of 2x18 W LED (4 ft) indoor tube light fitting with LED tube voltage range 90v-300v AC. Wiring/ connection of fitting with not less than1.5 sq.mm cu. Similar to Havells batten cat no.REGALBATTENTSUPTO2X22W SSBSWH and tube cat. no. PHOTONULTRAE2.01213T8SSTL18WLED865SPC. Wire through PVC flexible pipes. Fixing of fitting with aluminium. clamps and steel nut- bolts. Luminaire warranty period will be five years from the date of installation. Make of luminaire - Philips, Havells, Bajaj, Greatwhite. | — | — | — | 2,53,829.8 | |
| — | 25.00 | — | — | ||
| Installation. Testing,commissioning and Supply of 20W LED (4ft) inverter LED batten with square profile and polycarbonate channel lithium ion battery with charging time 8 hours-10 hours and back up time upto 4 hours indoor tube light fitting. Wiring/connection of fitting with not less than 1.5 sq mm cu. Similar to Havells cat no.LHEXACP7ENIW020. Wire through PVC flexible pipes. Fixing of fitting with aluminium clamps and steel nut-bolts. Luminaire warranty period will be five years from the date of installation. Make of luminaire - Philips, Havells, Bajaj,Crompton, C&S. | — | — | — | 15,925 | |
| — | 35.00 | — | — | ||
| Fixing, connection and supply of 36 W LED high performance 2x2 surface mounted luminaires which provides soft-light and glare free symmetrical illumination, Fixture size: (LxWxH) in (560x560x45) mm similar to Havells cat. no.: PLANOSUR2x2PLS36WLED840G2S including all accessories as per site requirement. Make of luminaire - Philips, Havells, Bajaj, Crompton, Greatwhite. Luminaire warranty period will be five years from the date of installation. | — | — | — | 2,73,000 | |
| — | 35.00 | — | — | ||
| Fixing, connection and supply of 36 W LED 2x2 ft ultra slim recessed pannel similar to Havells cat. no.: VENUSNEO2X2PLR36WLED 857G2 including all accessories as per site requirement. Make -Bajaj. Philips, Havells, Greatwhite. Luminaire warranty period will be five years from the date of installation. | — | — | — | 1,15,024 | |
| — | 50.00 | — | — | ||
| Fixing, connection and supply of 18 W LED recessed mounted pressure die-cast aluminium luminaire in powder coated white finish in round profile with optimized heat sink for efficient heat dissipation and independent 20 electronic LED driver similar to Havells cat, no.: EDGEPRONEORDDLRISWLED840S including all accessories as per site requirement. Make of luminaire-Philips, Havells, Bajaj, Crompton, Greatwhite. Luminaire warranty period will be five years from the date of installation. | — | — | — | 1,25,000 | |
| — | 50.00 | — | — | ||
| Fixing, connection and supply of 18 W LED surface mounted pressure die-cast aluminium luminaire in powder coated white finish in round profile with optimized heat sink for efficient heat dissipation and independent electronic LED driver similar to Havells cat. no.: EDGESURFACERDDLR18WLED840S including all accessories as per site requirement. Make of luminaire -Philips, Havells, Bajaj, Crompton, Greatwhite. Luminaire warranty period will be five years from the date of installation. | — | — | — | 1,50,000 | |
| — | 100.00 | — | — | ||
| Supply, installation, testing & fixing of 10 W LED 2 ft plastic batten with white acrylic cover, luminaire type BCLSB 10 WH to similar 20 Bajaj Havells, Halonix, Surya, Philips, LED Luminaire warranty period will be five years. | — | — | — | 34,096 | |
| — | 50.00 | — | — | ||
| Installation, connection, testing & commissioning of ceiling fan and regulator including all accessories as per site requirement. (Fan and regulator will be supplied by Railway.) | — | — | — | 841.5 | |
| — | 20.00 | — | — | ||
| Installation ,testing & commissioning of Exhaust fan with required material such as nut bolt, connection cable etc. as per instruction of site incharge. | — | — | — | 910.8 | |
| — | 250.00 | — | — | ||
| Supply and Fixing of copper pipe of condenser coil during installation/ shifting of split AC1.5/2.0 ton capacity. | — | — | — | 24,830 | |
| — | 27.00 | — | — | ||
| Installation, testing, commissioning and supply of DBOXx MCB protected power unit 16/25 Amp. 240 volt with sheet steel enclosure 16/25A MCB DBOXX MCB protected power unit HSN Code: 8536. Make - Havells, L&T, Legrand. | — | — | — | 17,864.55 | |
| — | 30.00 | — | — | ||
| Earthing arrangement by providing earth electrode of Gl pipe 50 mm dia (B class) 4.5 meter long with flange including 6 SWG Gl earth wire from earth pipe to connecting point on switch board to distribution board/pole etc. as per site requirement including masonry enclosure as per Tech specification at annexure 'A' relevant ISS & IE rules and site requirements. A suitable CI/MS/RC Coover as approved by Rly. Representative, cover with locking arrangement shall be provided. | — | — | — | 70,200 | |
| — | 4.00 | — | — | ||
| Supplying and fixing of 4 strips CU BBC 300 mm long of 100A cap, Make- Standard/Havells/Bentec/C&S | — | — | — | 19,496 | |
| — | 6.00 | — | — | ||
| Supplying and fixing of 4 strips CU BBC 300 mm long of 200A cap, Make- Standard/Havells/Bentec/C&S | — | — | — | 48,528 | |
| — | 4.00 | — | — | ||
| Provision of fabrication, installation, testing & commissioning of LT panel board fabricated of 14 SWG MS sheet metal fabricated dust and vermin proof cubical type complete with bus bar enclosed wall mounting including painting with 02 coats of synthetic paint equipped, fitted and connected to feeders/bus bars with MCCB 4 pole 200Amp. Breaking capacity 50kA -01 no. (as incoming) 100Amp. MCCB four pole breaking capacity 50kA-02 nos. & 63 Amp. four pole MCCB breaking capacity 50kA-02 nos. (as out going) with ammeter '0-100A'-05 nos. voltmeter (0-500) LED indication lamp (RYB) - 03 nos. HRC fuse -01 no., copper bus bar 20 Kg on the pre- fabricated LT panel. Make of MCCB-Havells, L&T, ABB, Legrand. | — | — | — | 3,10,550 | |
| — | 8.00 | — | — | ||
| Supplying and fixing 8 way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, inter connections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator). Make-Havells, Anchor, Capital. | — | — | — | 20,584 | |
| — | 4.00 | — | — | ||
| Supplying and fixing 16 way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, inter connections, powder painted including earthing etc. as required.(But without MCB/RCCB/Isolator) Make- Havells, Anchor, Capital. | — | — | — | 12,564 | |
| — | 108.00 | — | — | ||
| Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of single pole in the existing MCB DB complete with connections, testing and commissioning etc. as required. Make-Havells Anchor.Capital. | — | — | — | 27,648 | |
| — | 16.00 | — | — | ||
| Supplying and fixing following rating, double pole, (single phase and neutral), 240 volts, 6-40 Amp RCBO having a sensitivity 30mA in the existing MCB DB complete with connections, testing and commissioning etc. as required., 25 amps. make-Havells, HPL, Legrand,L&T,C&S, Anchor. | — | — | — | 69,280 | |
| — | 250.00 | — | — | ||
| Supplying and installing of 300 mm width X 62.5 mm depth X 2.0 mm thickness size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required. Make-OBO Leviton Cone | — | — | — | 2,32,000 | |
| — | 36.00 | — | — | ||
| Fixing & Supply of 40W LED post top Lantern, Decorative Post Top LED light fitting, Spun aluminium housing,LED with clear diffuser, integral driver with 2 feet steel pipe stand and IP 66 protection similar to Trans rail Model - TLLPTALPDCANEMONE-40W, Make-Bajaj, Crompton, Havells. Philips and Transrail. | — | — | — | 5,23,800 | |
| — | 36.00 | — | — | ||
| Fixing and supply of 3 mtr CI-CA-GI combo pole with PU paint on surface along with arrangement to mount post top lantern. Bajaj, Crompton, Havells, Philips and Trans rail. | — | — | — | 6,98,400 | |
| — | 36.00 | — | — | ||
| Fixing and supply of M16x400mm long TS-600 grade foundation bolts along with required templates for 3m pole. | — | — | — | 41,904 | |
| — | 2000.00 | — | — | ||
| Laying and fixing one no. XLPE/PVC Aluminium Conductor 1100 Volt grade of size exceeding 25 sq mm but not exceeding 120 sq mm on surface/wall/rail pole through Gl pipe as per site required. (If cables will be supplied by Railway to contractor and transportation up to site shall be done by contractor.) | — | — | — | 39,500 | |
| — | 3500.00 | — | — | ||
| Laying and fixing of one number XLPE Cable 1100V grade of size exceeding 25 Sq.mm direct in ground one meter depth including excavation, sand cushioning, and refilling to trench as required. (If cables will be supplied by Railway to contractor and transportation up to site shall be done by contractor.) | — | — | — | 1,43,045 | |
| — | 3500.00 | — | — | ||
| Laying of one no. additional PVC insulated and PVC sheathed/XLPE cable of 1100V grade up to 120 sq. mm direct in ground including excavation, sand cushioning protective covering and refilling of trench as required. (If cables will be supplied by Railway to contractor and transportation up to site shall be done by contractor.) | — | — | — | 75,565 | |
| — | 1050.00 | — | — | ||
| HDD cabling including cost of hiring of HDD machine at site (Cable will be supplied by Railway) including handling of stores materials, preparation of site and boring for placing of 100 mm inner dia HDPE/ DWC pipe for crossing of HT/LT XLPE cable together at Bridges/Culverts/Track/Pucca road crossing. Boring trench shall be minimum 3 mtr below the river bed and 1 mtr below Track/Road/Pucca Road crossing area. This includes supply of HDPE/DWC pipes and accessories as per requirement of site and cost of fuel & all other items which will be required for laying of cable through it. The work shall be executed as per instruction of site engineer. (a) Boring up to length 150 mtr. | — | — | — | 10,61,161.5 | |
| — | — | — | Above/ 668250.00 Below/P | ||
| Fixing and supply of LED street light 60 W New generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embedded PC cover having TOP Opening seperate driver compartment with IP66 protection and impact resistance of IK07 on pole/wall with suitable size G.I. Pipe of medium gauge smooth bend with 120degree (2 feet + 1 feet) long, MS clamp, Nut bolt etc. as required, Kit-kat fuse 16amp in suitable size MS box should be provided with G.I. pipe. Wiring/connection of fitting and kit-kat fuse will be done with not less than 2.5 sq.mm aluminium wire through G.I. pipes and PVC flexible pipes complete in all respect. Similar to Havells cat. no.ENDURAPEARLNEOSL60WLED757PASYTOPCAST. Make of Luminaire, Philips, Havells, Bajaj, Crompton. LED Luminaire warranty period will be 05 years. | — | 90.00 | — | — | |
| — | 60.00 | — | — | ||
| Fixing and supply of LED street light 90 W New generation energy saving and environmental friendly long life LED street light made up ot pressure die cast aluminium housing with high efficiency LEDs as lighting source and lens embedded PC cover having TOP Opening eperate driver compartment with IP66 protection and impact resistance of 1K07 on pole/wall with suitable size G.I. Pipe of medium gauge smooth bend with 120degree (2 feet+I feet) long, MS clamp, Nut bolt etc. as required, Kit-kat fuse 16amp in suitable size MS box should be provided with G.I. pipe. Wiring/ connection of fitting and kit-kat fuse will be done with not less than 2.5 sq.mm aluminium wire through G.I. pipes and PVC flexible pipes complete in all respect. Similar to Havells cat, no. ENDURAOMNIPLUSSL90WLED757SASYTOPC. Make of Luminaire -Philips, Havells, Bajaj, Crompton, Panasonic. LED Luminaire warranty period will be 05 years. | — | — | — | 5,69,340 | |
| — | 32.00 | — | — | ||
| Supply, delivery & Fixing of octagonal pole hot Dip Galvanized in single dip average 70 micron DFT, designed for maximum wind speed of 169KM/Hr., BOP-7030 type pole of 6 m long, top dia 70mm, bottom dia. 130mm sheet thickness 3mm, in single section with Base plate (220x220x12)mm (LxBxT) with 4x20mm dia. 700mm long with 100mm projection foundation bolt complete with smart pack junction box with bakelite sheet, 6A MCB & stud terminals (for mounting inside base component of pole) and internal wiring for terminal to fitting with 2x2.5 sq.mm cable including single arm bracket 1 mtr. long suitable for 3 to 10 mtr. pole of reputed make. Make Bajaj, Transrail, Bansal, Jindal, Gammon Group | — | — | — | 4,95,040 | |
| — | 32.00 | — | — | ||
| Making of foundation suitable for 3 to 8 mtrs octagonal pole as per site incharge/4'X4'X4' manufacture dimension as per site requirement. | — | — | — | 74,961.6 | |
| — | 296.00 | — | — | ||
| Design, manufacture, display of wall/hanging/floor mounting type LED illuminated sign/direction boards in half elliptical shape. The display sheet shall be of unbreakable 040 translucent polycarbonate sheet of 2 mm thickness. The text/graphics matter visibility shall not be less than 160 deg. The approved colour text and graphics shall be printed/router cut on monomeric calendered vinyl of 70 um thickness and shall be firmly pasted on display sheets. The mounting arrangement shall be hanging, wall mounting, ceiling mounting, pole mounting or floor mounting and as per site requirement. The signange shall have the integral mounting arrangements with sturdy structural frame and ACP cladding on the back side of the signage to avoid rusting and entry of dust. The LED board shall have uniform illumination with 4-8 W/sq.ft and brightness more than ambient light. suitable size end cap of 1.5 mm thick SS 304 should be provided. | — | — | — | 5,18,000 | |
| — | 296.00 | — | — | ||
| Erection and installation of wall/hanging/floor mounting type LED illuminated sign/direction boards in half elliptical shape. The display sheet shall be of unbreakable 040 translucent polycarbonate sheet of 2 mm thickness. The text/graphics matter visibility shall not be less than 160 deg. The approved colour text and graphics shall be printed/router cut on monomeric calendered vinyl of 70 um thickness and shall be firmly pasted on display sheets. The 58 mounting arrangement shall be hanging, wall mounting, ceiling mounting, pole mounting or floor mounting and as per site requirement. The signange shall have the integral mounting arrangements with sturdy structural frame and ACP cladding on the back side of the signage to avoid rusting and entry of dust. The LED board shall have uniform illumination with 4-8 W/sq.ft and brightness more than ambient light, suitable size end cap of 1.5 mm thick SS 304 should be provided. | — | — | — | 78,440 | |
| — | 288.00 | — | — | ||
| Installation, testing, commissioning and fixing of 3D LED based name boards on ALP sheet of 3mm gauge thickness with projected alphabets of made of acrylic sheet in size of standard height as per space of alphabets with LED chip modular light. The work is including of erection of LED Board with minor modification on existing structure with required extra MS angle with painting of structure. Board in Hindi, English & Urdu. | — | — | — | 2,77,588.8 | |
| — | — | — | Above/ 290700.00 Below/P | ||
| Supply of 1140 LPM capacity Submersible Pump with Motor (20 HP) suitable for 415 Volt, 3 Phase 50Hz, Discharge Head 46 Mtrs. Complete with all accessories spares and tools (such as chain wrench, pipe wrench, allein keys, double ended spanners of Taparia make required for subject pump). As per attached Annexure 'A' for Pump motor capacity 1140 LPM at 46 m head set. make- KSB, Kirloskar Brothers Ltd, Jyoti. Inspection by consionee. | — | 2.00 | — | — | |
| — | 1.00 | — | — | ||
| Installation, erection, testing and commissioning of Submersible Pump Set 1140 LPM capacity complete with all accessories including electrical connection and supply of all suitable/required material in connection with installation of pump. | — | — | — | 8,880.6 | |
| — | 4.00 | — | — | ||
| Installation, testing, commissioning and supply of 20 HP automatic star delta submersible pump controller three phase max operating current 135% (A):40.5A, OLR(A):22 A-30 A, contractor: 32A including all accessories as per site requirement. Make - Havells, Crompton,C&S. | — | — | — | 77,706.2 | |
| — | 350.00 | — | — | ||
| Provision, fixing/laying at underground/surface/wall & supply at site of double walled corrugated (DWC) pipes or GI pipe for power cable protection with IS 14930 part- II along with the socket coupler. T joints to be provided at the junctions where ever required. Size of outer dia 120 mm/inner dia 103.5 mm. The pipe should be ISI marked. | — | — | — | 1,13,200.5 | |
| — | 500.00 | — | — | ||
| Fabrication as per site requirement and erection on pre erected steel tubular/rail pole/Cage for water cooler of MS Cross Arm bracket with nut bolt, clamp etc including supply of cross arm bracket Nut-bolt, clamp etc. | — | — | — | 38,000 | |
| — | 2.00 | — | — | ||
| Installation, testing & commissioning of water cooler 150 ltr capacity with nut bolt with other accessories(inner pipe, outer pipe etc) as per requirement of site instruction of site charge. | — | — | — | 2,609.4 | |
| — | — | — | Above/ 245916.00 Below/P | ||
| Supply of 11 mtr high mast system totally hot dip galvanized having in One Section, Top dia 100mm, bottom dia 360mm and Sheet thickness 3mm, PCD-445 MM, suitable for 50m/sec. wind velocity as per IS 875 Part 3 along with head frame, luminaries carriage suitable to install 06 nos. of luminaries in symmetrical arrangement and accessories required such as supply of raising lowering system of 11 M high mast comprising Single Gear Double drum (SGDD), 7/19 construction, 5mm diameter SS wire rope having Two Wire Rope System, trailing cable, connector, integral power tool motor, manual handle, junction box etc. Make-TRANSRAIL, Bajaj, Philips, Surya, Crompton, VALMONT | — | 3.00 | — | — | |
| — | 3.00 | — | — | ||
| Supply of foundation bolts M24 X 850 MM.TS 600. manufactured from special steel along with nuts, washers, anchor plates and templates. Make- TRANSRAIL, Bajaj. Philips, Surya. Crompton. VALMONT | — | — | — | 20,493 | |
| — | 18.00 | — | — | ||
| Fixing, connection and supply of LED Flood Light 250 Watt Energy saving, environmental friendly, long life, exclusive innovative die-cast aluminium IP66 Nood light, suitable for highlighting architectural facade and general purpose lighting. Similar to Bajaj GLFAM F 275L WH SY PC SD V2-113984. (LED Light Warranty will be five Years). Make of luminaire -Philips. Havells, Bajaj, Crompton, Transrail | — | — | — | 1,35,253.8 | |
| — | 3.00 | — | — | ||
| Supply of LED type single dome aviation obstruction light. Make-TRANSRAIL, Bajaj, Philips, Surya, Crompton, VALMONT. | — | — | — | 8,197.2 | |
| — | 3.00 | — | — | ||
| Supply of feeder panel comprising main incoming 32A TPN MCB, auto tirne switch, 25A TP contractor, reversing starter and protective system etc as required for operation of high mast system. complete and raise lower push button. Incoming 35sq.mm and outgoing 16 & 2.5sq.mm terminals. Make- Havells. Anchor, HPL | — | — | — | 49,183.2 | |
| — | 3.00 | — | — | ||
| Construction of suitable shallow foundation with 1:2:4 concrete for the highmast considering the safe soil bearing capacity at site as 10 T/sq mtr at 2 meter depth with all materials and labour. | — | — | — | 92,218.5 | |
| — | 3.00 | — | — | ||
| Erection of the high mast with the help of suitable tools and plants, wiring of luminaries with all wiring materials like PVC insulated PVC sheathed flexible cable of suitable copper conductor cores of 1.5 sq.mm, lugs, MCB and all labour. | — | — | — | 40,986 | |
| — | 3.00 | — | — | ||
| Installation of the outdoor stand mounted feeder pillar by grouting tie stand in concrete. | — | — | — | 10,246.5 | |
| — | 16.00 | — | — | ||
| Fabrication, supply & fixing of Mobile/laptop charging board with 10 Nos. switches & Sockets combined modular type in two ladders 5 Nos, in each ladder with indication lamp made of 25 x 25 Sq.mm square pipe heavy duty Hylum sheet thickness 3 mm. board size 3'x2.5"x6". Make of switch Havells, Cona ISI make approved by competent authority. | — | — | — | 30,576 | |
| — | 2.00 | — | — | ||
| Supply at site, installation, testing and commissioning of color signal light panel with automatic operation of 3 source of supply capacity 60 amp Approved by RDSO/LKO connection on incoming as well as outgoing, testing of frequency of changing over from one source of supply to another source of supply. Make - JAPS RDSO approved. | — | — | — | 89,746.66 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
GCC_April-2022_2022_CE-I_CT_GCC-2022_POLICY_27.04.22.pdf
ATTACHMENT
ACS01to11_new.pdf
ATTACHMENT
ANX-VVA.pdf
ATTACHMENT
annualturnoverformatCAVIB.pdf
ATTACHMENT
DECLARATIONREGARDINGASSOCIATIONWITHGAZETTEDRAILWAYOFFICERENGINEER-1.pdf
ATTACHMENT
Mandateform.pdf
ATTACHMENT
Letterofcredit.pdf
ATTACHMENT
TenderDocument2ndEntryNKE_.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .