EEE-II/TC/2021-22/24.3

Amount

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (but without charcoal/ coke and salt ) as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 6 SWG dia G.I wire on surface or in recess for for loop earthing as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size in the existing RCC/ HUME/ METAL pipe as required. (a) Upto 35 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 kV grade of following size in the existing masonry open duct as required. (a) Upto 35 sq. mm

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc..direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required.63 mm dia (OD-63 mm & ID-51 mm nominal)

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc. in the existing trench, complete as required. 63 mm dia (OD-63 mm & ID-51 mm nominal)

Supply of XLPE insulated PVC sheathed Al.conductor armoured cable 1.1 KV grade confirming to IS of following size:- a) 2x10 sq.mm

Supply of XLPE insulated PVC Sheathed Aluminium Conductor un armoured cable 1.1 KV grade confirming to IS 7098 of following size. A) 2 core 10 sq mm

Supply and drawing following sizes of FRLS PVC insulated copper conductor , single core cable in the existing surface/recessed steel/PVC conduit as required.(a) 2x2.5 Sq mm

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/recessed steel/PVC conduit as reqd. a) 2X1.5 Sq mm

Supply & fixing of 32mm dia G.I.Pipe 1Mt. long bracket i/c wiring with 1.5 sq.mm copper conductor wire as reqd.

Fabrication, supplying, & Fixing Class -B Galvanised Single overhang arm bracket made out of 250 mm long galvanized top tube with cap and 250 mm long 32 mm dia galvanized pipe with tightening bolts complete as required,

Supply and fabrication of pole protection system made up of 8SWG steel wire mesh of size 25mmx75mm rectangular with 50mmx50mmx6mm MS angle iron for supporting the mesh and grounding the protection system in suitable quality of CC etc as reqd.

SITC of 60 watt LED Street light Luminiare fitted with lens, made of pressure die cast aluminium housing & toughened glass cover complete with the following specifications as reqd. Total System Wattage= 60 Watts + /- 5% Luminaire Efficacy (Lumens/Watt): >= 100 Lm/Watt Power Factor: >= 0.95 Protection: IP66

SITC of 150W LED Flood Light luminiare fitted with lens, made of pressure die cast aluminium housing & toughened glass cover complete with the following specification as reqd. (b) Total system wattage =150 watt +/- 5% (d) Luminaire Efficacy>=100 Lm/w (e) Power Factor>=0.95 (f) Protection Class- IP-66

Fabrication, supply & erection of following size flange mounted hot dip galvanized octagonal pole made out from HT steel plate,window with flash cover with full vertical window cover at appropriate height from the base plate on existing cement concrete pedestal as required. i/c supplying and fixing of 6 mm thick laminated mounted sheet inside the window mounted on and i/c providing and welding 3 Nos GI strips 4 mm thick of suitable length and having suitable size tapped holes as reqd,terminal block suitable for 25 Sq mm conductor - 4 Nos & shorting links on DIN channel i/cpdg and fixing DIN channel of suitable lenght, 6 amp. SPMCB 'C' characteristics, earth stud, cable support clamp suitable for upto 4X25 Sq mm cable.,Logo/Name of manufacturer shall be embossed on the pole. Galvanization as per relevant IS.(a) 5.0 Meter Height, 3 mm thick, bottom dia of 130 mm & top dia of 70 mm base plate of size 225x225x12 mm thick

Fabrication , Supplying,Installation,testing,Commissioning of 12 mts.high mast System with its accessories ,Mast shaft shall be in one section , hot dip galvanized 4mm thick(Single dip ) inside & out sides &suitable for wind velocity as per IS 875 part3 .There shall be in longitudinal seam weld per section and No circumferential weld. It should also included accessories For High Mast head frame ,2 point suspension system with steel wire rope 5mm dia. (7/19construction) single drum winch ,galvanized lantern carriage arrangement suitable for 4/6 Nos. Flood Light luminaries symmetrically And its control gears boxes and lighting finial ,the mast shall have integral type manual tool mounted at the base compartment of its raising and lowering operation with foundation bolts and Anchor plate and control panel housing suitable RCC (1:2:4) shallow foundation of size 1m(L) x 1m wide and 2m deep i/c excavation of earth, providing cutting, bending and placing in position, reinforcement of cold twisted bars of 12 mm dia -2100mm long (approx.) - 16 nos.and reinforcement of cold twisted bar of 8 mm dia - 3700 mm (approx.) - 13 nos. (with 150 mm spacing) as required with positioning of foundation bolts and providing DWC HDPE pipe for cable entry & exit as required for the high mast considering The safe soil bearing capacity at site as 10T/sqm at 2mts. Depth with all material i/c 4Nos S.P MCB,63Amp.DPIsolator etc as reqd. Logo/Name of manufacturer shall be embossed on the pole. Galvanization as per relevant IS.Logo / Nmae of manufacturer shall be embossed on the pole. Galvanization as per relevant IS.

Providing and Laying in position 1:2:4 grade reinforced cement concrete foundation of size 450mm(L)x450 mm wide and 1000 mm deep i/c excavation of earth, providing cutting, bending and placing in position, reinforcement of cold twisted bars of 12 mm dia-960 mm long (approx)-8 Nos. and reinforcement of cold twisted bars of 8 mm dia-1400 mm (approx)-6 Nos(with 150 mm spacing) as required with supplying and positioning of 4 Nos foundation bolts 16 mm dia, 600 mm long, J type i/c 2 Nos template anchor plated of size 225mmX225mmX3mm and providing DCW HDPE for cable entry and exit as required for 3 m and 5 m pole.