SPECIAL REPAIRS TO BUILDING NO T-18 AT LEKHAPANI MIL STN

Amount

Dismantling of plain or corrugated steel sheeting any guage, thickness including Nanital or similar pattern roof coverings complete all as specified and as directed.

Dismantling of wall and ceiling boards (fiber, pulp, insulation etc.) or insulation boards/slabs/blankets, any thickness, including frames and cover fillets complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as directed.

Taking down roof trusses, coupled rafters or trussed beams of clear span above 4 mtrs and upto 8 mtrs and refixing the same after repair/renewal of demaged wooden members (New members shall be measured and paid separately) complete all as specified and directed by Engineer-in Charge.

Dismantling timber scantlings in unframed timber work 40 sq.cm and over in section, in any position and keeping serviceable scantling in safe custody for reuse complete all as directed by Engr-In-Charge.

Dismantling timber fillets, rails, posts, rafters, purlins, etc in unframed work under 40 Sq.cm in section in any posotion complete all as directed.

Demolition of reed, lathing, single or double, including battens and plaster or chicken wire lathing complete all as directed.

Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars etc. but excluding ashlar facings, dressed stone work & precast concrete articles complete all as directed.

Demolition of unreinforced cement Concrete floor as in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as directed.

Taking down chowkat or frame with shutters (without taking off shutters from the frame) not exceeding 1.5 sqm each including iron mongries and making good to disturbed surfaces complete all as specified and as directed.

Taking down chowkat or frame with shutters (without taking off shutters from the frame) exceeding 1.5 sqm but not exceeding 4.0 sqm each including iron mongries and making good to disturbed surfaces complete all as specified and directed by the Engineer-in-Charge.

M&L for brick work with sub class old size 'B' bricks, straight or curved on plan to any radius, built in cement mortar 1:4 as in half brick thick walls complete as specified and directed.

M&L for 2nd class hard wood scantling, clean swan, timber fixed as in unframed work complete all as specified and as directed.

Fixing only for 2nd class hard wood scantling, clean swan, timber fixed as in unframed work complete all as specified and as directed. Note :- Serviceable scantling obtained from dismantling shall be reused.

M&L for 2nd class hard wood scantling, clean swan, timber fixed as in framed work complete all as specified and as directed.

Fixing only for 2nd class hard wood scantling, clean swan, timber fixed as in framed work complete all as specified and as directed. Note : - Serviceable timber scantling obtained from dismantling shall be reused.

S&F galvanised steel wire netting 0.5 to 0.6 mm dia and 25 mm size of mesh for lathing, fixed with tinned of wire staples to wooden frame in all including all laps, cutting and waste complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 on fair faces of brick or concrete surfaces in two layers (5mm thick finishing layer over 10mm thick backing layer) finished fair and even with mixing water proofing compound to top layer as per manufacturers instruction and as directed (WPC will be measured separetely).

Supply only Integral water proofing compound of approval brand complete all as specified and directed.

M&L for preparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of primer complete all as specified and directed.

M&L for rendering 10.mm thick plaster in cm (1:6) on fair faces of brick work or concrete surfaces including finishing top even and smooth without using extra cement complete all as specified & directed.

M&L for preparation of new plastered surfaces of wall and preparing surfaces as directed and applying two coats of distemper oil emulsion over a coat of primer with & including 1 mm thick wall care putty complete all as specified & directed.

S&F 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

S&F roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc Fe 410 -W (GdeE- 250) quality A complete all as specified and as directed.

Fixing only roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. complete all as directed. Note : - Serviceable truss and purlins obtained from dismantling shall be resued.

Supply & Fixing plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment cofirming to Fe 410 -W (Gde- E- 250) quality-A complete all as specified and directed.

M&L for Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, longbut length of bolt exc 5cm but n exc 10cm long

M&L for pre-painted hot dip aluminium-zinc alloy metallic coated corrugated steel sheet, any pattern corresponding to IS15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ 150, 0.50mm thick of an approved colour and having yield strength of 550 MPa as in roof covering fixed with self tapping screws as specified including necessary scaffolding and safety measures at any floor complete all as specified and as directed

M&L for hot dip aluminium-zinc alloy metallic coated plain steel sheet as per IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ 150, 0.50mm thick of an approved colour and having yield strength of 550MPa as in ridge/valley/gutter/eaves boardings fixed with self tapping screws as specified including necessary scaffolding and safety measures at any floor complete all as specified and as directed.

Providing and fixing inter locking metal grid (snap grid for false ceiling) of size 605mm x 605mm in true horizonatal level, hot dipped galvanised steel sections consisting of main “T” runner with suitably spaced joints to get required length and size 24mm x 38mm made from 0.30mm thick (Min) sheet spaced at 1200mm centre to centre and cross “T” of size 24mm x 28mm made of 0.30mm thick (Min) sheet, 1200mm long spaced between main “T” at 600mm centre to centre to form a grid of 1200mm x 600mm and secondary cross “T” of length 600mm and size 24mm x 28mm made of 0.30mm thick (Min) sheet to be interlocked at middle of the 1200mm x 600mm panel to form grids of 600mm x 600mm and wall angle of size 24mm x 24mm x 0.4mm. Main “T” runner to be suspended from purlins or truss member using 2 to 3 mm dia GI wire, 1200mm x 600mm centre to centre all complete for all heights as per specifications and as directed by Engineer – in - Charge.

M & L for 4 mm thick high pressure, oceanic pre-primed, self embossed, non asbestos fibre cement decorative board, water, termite and fire resistant for insulation ad acoustic purpose to be placed in grid system hold down clips with provision of high fixtures, air conditioning, diffuser and ducts, sprinkler, smoke detector etc, complete all as per manufacturer instructions.

S&F 30 mm thick, flush door shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides & both face is covered with decorative face veneer with lipping / frame to match & fixed to chowkats complete all as specified & directed.

S&F 35 mm thick, hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a) fitted to chowkats complete all as specified & directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified & directed.

S&F 100 mm size, butt hinges extruded aluminium alloy with galvanised mild steel hinges pin, anodised and fixed, type B-21 complete all as specified and as directed.

S&F 200 mm size, aluminium anodised , barrel tower bolts of extruded section & fixed complete all as specified and as directed.

S&F 150mm size aluminium handles, cast type, anodized and fixed complete all as specified & as directed.

S&F 300mm length of bolt, aluminium alloy, anodized, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified & as directed.

S & F for aluminum powder coated (powder coated of required colour) three track sliding windows frame top & sides of size 92 x 31.75 x 1.50mm (section No 20831) bottom of size 92 x 31.72 x 1.50mm (Soction of 20832) and shutter top & bottom of size 40 x 18 x 1.55 (section 20738) and lock side shutter frame of size 40 x 15 x 1.45mm (Section 20737) with rubber gasket, beading and locking arrangement including making good to the disturbed portion complete including stainless steel wire mesh 0.36mm nominal dia with 1.40mm average aperture and fixed with stainless steel wire staples and fixing 5mm thick glass with necessary rubber beading gasket etc complete all as specified and as directed.

M&L for 40mm thick PCC (1:2:4), type B1, (using 20mm graded stone aggregate) as in floors, finished even and smooth, using extra cement complete all as specified and directed.

M&L for Glass dividing strips, 3 mm thick 38mm wide and inserted in position, conform to design complete all as specified and directed

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. including brushing neat cement slurry with 3.0 kg of cement per sq. metre. Complete all as directed.

M&L for coloured non skid joint free ceramic tiles of 7mm to 8mm thick area of each tile exceeding 0.18 Sqm but not exceeding 0.38 sqm in floors, etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 for laying floor finishes complete all as specified & directed.

M&L for coloured non skid joint free ceramic tiles of 7mm to 8mm thick area of each tile exceeding 0.18 Sqm but not exceeding 0.38 sqm in floors, etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 for vertical surfaces such as skirting etc complete all as specified & directed.

M&L for preparation of new painted surfaces of steel of any description, not otherwise described, over 10 cm width or girth and applying two coat of synthetic enamel paint over one coat of red oxide complete all as specified & directed.

M&L for preparation of old painted surfaces of steel of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified & directed.

M&L for preparing new wood & wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified & directed.

M&L for preparing new or old wood & wood based surfaces of any description, not otherwise described, treated with creosote oil complete all as specified & directed.

M&L for preparing old wood & wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified & directed.

M&L for 75 mm thick Cement concrete type C-2, 1:3:6 (using 40 mm graded stone aggregates) as in plinth protection etc, finishing cement concrete surface even and smooth with out using extra cement including making joints with hot bitumastic mix in proportion of bitumen and sand 1:2 complete all as specified & as directed.

S&F chromium plated curtain rod 25 mm dia, with and including MS chromium plated decorative round finals on either end provide a visually balanced appearance including MS chromium plated brackets fixed to wall with 30 mm wooden steel screws and PVC rawl plug, anchors and installations complete all as specified and directed by Engineer-in-Charge.

Taking down copper/aluminium point wiring, (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as directed.

Material and labour for providing point wiring for controlled by one switch with using 1.50 sq.mm (nominal area), stranded copper conductor, single core PVC insulated FRLSH unsheathed cable (Maintaining Colour Code) 1100 volts grade with and including PVC casing and capping of suitable size including PVC accessories / fittings and fixtures fixed on surface with using new PVC board or sunken type pressed steel box of adequate size, terminal boxes for mounting fittings/junction boxes with and including all accessories and using 1.5 sq.mm (nominal area), stranded copper conductor, single core PVC insulated FRLSH unsheathed cable green in colour as in earth continuity conductor connected to common earth dolly and connecting upto fittings complete all as specified and directed for One light point controled by one one way 5 Amp switch complete all as speciifed & as directed. NOTE: The quoted rates shall be inclusive for fixing casing caping to surface with using PVC raw plugs and provision of PVC boards/terminal/junction boxes of any shape and size.

All as per item No 53.00 here-in-before but for One fan point controlled by one , one way 5 Amp switch complete all as specified & as directed.

All as per item No 53.00 here-in-before but for One 5 pin socket outlet 05 Amp on independent board complete all as specified & as directed.

All as per item No 53.00 here-in-before but for One 5 pin socket outlet 05 Amp on same board complete all as specified & as directed.

All as per item No 53.00 here-in-before but for one 15 Amps socket outlet using 2.5 sq mm,copper conductor with 2.5 sq mm,PVC insulated single core cable for earth continuity conductor complete all as specified & as directed.

M&L for providing sub main wiring with two single core 6.00 Sqmm (nominal area) PVC Insulated FRLSH unsheathed multi stranded copper conductor cable 1100 volts grade drawing through PVC casing-capping complete including 6.00 Sqmm PVC insulated unsheathed multi stranded FRLSH single core copper conductor cable for earth wire including taking down/removing old one and making good distrubed surfaces of walls, floors, etc complete all as specified and directed. Note : (i) Three runs of single core 6.00 Sqmm multi stranded copper cable and one run of casing caping shall be measured as one run length (ii) Extra length of cable required for connection to DBs/MCBs shall deem to be included in unit rate quoted by contractor against the item (iii) Earth wire run inside the casing capping.

Supply & fix switch piano flush button, single pole, one way 5 Amp complete all as speciifed & as directed.

Supply & fix socket outlet, 2 in 1,5 pin 5 Amp flush type complete all as speciifed & as directed.

Supply & fix switch socket combination 2 in 1, 2 and 3 pin 5 Amp flush type complete all as speciifed & as directed.

Supply & fix switch socket combination, 5 in 1, multipurpose 5/15 Amps flush type universal complete all as speciifed & as directed.

Supply & fixing ceiling fan regulator,electronic type,step type 5 speed A/C, 230 volts on the existing laminated sheet complete all as specified and directed.

S & F MCB SP 6 to 32 Amps 240 volts , C Curve , 10 kA complete all as speciifed & as directed.

S & F MCB SPN 32 Amps 240 volts , C Curve , 10 kA complete all as speciifed & as directed.

S&F single pole and neutral DB wall mounting type,240 Volts,12 Way with 200 Amps rated bus bar,double door suitable for fixing MCB's including connecting etc and taking down U/S DB ,main switch complete all as speciifed & as directed.

S&F single pole and neutral DB wall mounting type,240 Volts,8 Way with 200 Amps rated bus bar,double door suitable for fixing MCB's including connecting etc and taking down U/S DB ,main switch complete all as speciifed & as directed.

Supply & fix ceiling rose, 3 terminals, surface bakelite, / PVC / Polycarbonate complete all as speciifed & as directed.

Material and labour for earthing complete with galvanized steel earth plate electrode 600mm X 600mm X 6mm buried directly in ground vertically to a depth not less than 2.25 meter below normal ground level (with top edge of earth plate not less than 1.5 meter below ground level) connected to galvanized iron earth lead wire 4mm dia, (main earthing lead ) by means of galvanized bolts, nuts and washers all as shown in electrical plate no 3 of MES Schedule Part-I (1991) with connected to earth test point & to main switch board with & including adequate quantity of charcoal dust and common salt alround earth plate & 15 mm dia GI pipe light grade for earth lead protection pipe for suitable length and GI pipe 20 mm dia light grade for watering pipe with funnel & wire mesh including necessary earth work and PCC (1: 3 : 6) type C-1 for earth pit and 40 mm thick pre-cast RCC cover in 1 : 2 : 4 type B1 with 3 Nos 8 mm dia TMT bars both ways complete all as specified & directed by Engineer-in-Charge.

S&F LED tube light fitting 4 ft. 1 x 18/20 watt with 230 volts, complete with all accessories internally pre-wired and fixed to walls/ceiling with screw including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed.

Supply and fixing Bldg security light fitting 20W watt with 230 Volts with IP 66 including service bracket min 1 mtr length of dia 25 mm dia GI pipe suitable for light with nut bolt and clamps High Impact resistance complete with all accessories internally pre-wired and fixed to walls complete all as specified and directed.

Taking down existing ceiling fan from bldg and keep aside the serviceable ceiling fan for reuse and uncerviceable ceiling fan deposited to MES store complete all as specified and directed by engr-in- charge s

Supply and fixing ceiling fans complete with blades, down rods , and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) including down rod of suitable size Bar and all fixing arrangements complete all as speciifed & as directed.

Refixing of serviceable celing fan in bldg including provision of fan hook complete all as specified and directed.

Supply & Fix fan hook made of 10mm dia TMT Bar for for hanging the ceiling fan complete all as specified and directed by engr-in- charge

Excavation in trenches not exc. 1.5 meter deep and not exc 1.5 metre wide for taking up/laying of under ground cable/pole and stay foundation and getting out in soft/loose soil complete as specfied and as directed.

Returning filling in including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as specfied and as directed.

Removing surplus soil to a distance not exc 50 meter and depositing where directed at a level not exc 1.5 meter above the starting point complete all as specified and as directed.

M&L for brick protection over cables inside the trench by using common burnt clay building bricks,sub-class"B" laid dry and flat and width wise along the axis of the trench complete all as specified and as directed by Engineer-in-Charge.

M&L for sand cushioning in cable trenches over & under the cables, with river washed coarse sand, as per standard practice with proper compaction complet all as specified and directed by Engr-in-Charge. Note : - (Punned down thickness shall be measured and paid for ).

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 sq mm 2 core, complete including taking down old u/S service wire.complete all as speciifed & as directed.

Supply and laying 50 mm dia GI tubing light grade complete with all fittings (ISI Marked) lain in trenches/fixed on pole/wall complete including taking down old unsv GI pipe complete all as speciifed & as directed.

Boring of holes under road, pavement, hard standing by for passing the cable throgh GI pipe complete all as specified and directed by Engr -in-Charge.

M&L for brick work with sub class old size'B' bricks, (except brick) straight or curved on plan to any radius, built in cement mortar (1:4) as in half brick thick walls complete as specified and directed.

Taking down cement or cement lime plaster, any description hacking for key, scrubbing down with water and removal of debris off the premsses etc complete all as specified and directed

M/S SINGH TRADERS

ms singh construction

Construction House

M/S Abhi Traders

RC CONSTRUCTION

M/s Singh enterprises