REPAIR TO JOINERY, TILING AND ROOF TREATMENT AT CENTRAL INSTITUTE AND SHELTERS UNDER ZONE-I B AREA AT JAIPUR MIL STN

Amount

Taking down of shutters of any description exc 1 sqm but n exc 2 sqm each

Taking down door chowkaht or frame of any description area n.exc 1.50 Sqm each without taking off shutters from the frame.

Taking down door chowkaht or frame of any description area exc 1.50 Sqm but n exc 4 Sqm each without taking off shutters from the frame.

S & F mild steel framed work as in door frame of angle or other section and fixed with angle cleats and connecting plates etc of Gde E-165 (Fe-290) Note:- Cost of welding butt hinges to the door frame deemed to included in quoted rate

M & L size 100x75mm, rebated, karoli stone chowkats with exposed faces close picked dressed, including 4 bolt holes ‘per upright’, erected in position and bedded and pointed in cement mortar 1:6 (Bolts measured separately)

S & F 35mm thick factory made plain, framed, paneled door shutters kiln seasoned and chemically pressure treated second class, hardwood (two panels) with lock rail and panel of 9mm thick BWP commercial marine grade ply wood bonded with high quality liquid phenol formal dehyde synthetic resin adhesive confirming to IS-710. The size of rails and style shall be as per IS-1003.

S & F 35mm thick factory made second class hardwood glazed and skelton door shutter kiln seasoned and chemically treated, open rebated and prepared to receive glass/ gauge etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc complete. The size of members of shutters shall be as specified in MES SSR Part-I.

S&F flush shutters 40 mm thick, solid core construction with block board core and plywood face panels, commercial type on both side faces covered with decorative face veneer with lipping / frame to match

Supply and fixing anodised aluminium frame for door , windows, ventilators with one or more rebates incl jointing cleat for fixing etc complete all as specified

Supply and fixing anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc complete

Supply and fixing anodised aluminium window and ventilator shutters, side hung type without sash, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium fittings such as peg stays 150mm long 1 No, hinges type B-21, 100mm long (2 No) suitable handle 2 No complete

S & F solid PVC door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube of 1.25 mm thickness suppling & fixing in opening as per specification & drawing.

S&F Factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S & F pressed steel factory made cupboard shutter with frame of 1.25mm thick and shutter 1mm thick PBI sheet with 6 Nos 3.15mm thick and 100mm long steel hinges Godrej pattern locking arrangement including 12mm dia vertical rod. Shutters shall be spray painted in factory (total width including frame shall be measured and paid)

S&F 300mm long aluminium anodized alloy sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts etc.

S & F 150mm long aluminium handles, cast type anodised complete

S & F 150mm long aluminium anodised barrel tower bolts of extruded section and fixed complete

S & F 100mm butt hinges medium weight cold rolled mild steel and fixed complete

S & F aluminium door stopper 75mm size with double pin and rubber shoe fixed to bottom rail of door shutter complete

S & F galvanised mild steel wire cloth 0.63 mm nominal dia of wire & average width of aperture 1.40mm and fixed with stainless steel wire staples

M&L cutting holes in stone walls built in Cement Mortar exc half but n exc one brick depth or embeded portion of hold fast or lugs incl making good to distrubed portion in CM 1:3 or PCC 1:2:4 type B1 as required complete all as specified.

Hacking out old broken glass (any thickness, size quality or description) from wooden frames glazed with putty or fixed with beads

S & F 5.5mm thick plain sheet glass ordinary quality to aluminium door/ window in sqaures not exc 0.5 sqm in each pane complete

M & L Preparing new wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer

M&L Two coats of synthetic enamel paint to steel surfaces over red oxide primer exc 10 CM in width or girth including preparation of steel surfaces.

S&F Double action floor door spring hydraulically regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box main body with stainless steel cover governing pivot made of brass other parts made of MS heavy duty complete all as directed by Engineer-in-Charge.

M&L for running welding in repairs to mild steel hinges coming out from steel frame( rates to be included for filling material and work place is segregated) thickness of metal to be welded n exc 6 mm

Taking down cement plaster or cement lime plaster/ tiles of any descrption on PCC/ stone surface/ brick surfaces of wall or ceiling including raking outs joints, hacking for key scrubbing down with water etc

M & L for rendering 15 mm thick on stone masonary surface or surface other than fair faces of brick work or on one side of lathing in CM 1:6 finished even and smooth without using extra cement

M & L for rendering 15 mm thick on stone masonary surface or surface other than fair faces of brick work in CM 1:4 finished even and smooth without using extra cement

M & L Rendering 10 mm thick on ceiling in CM 1:3 finished even and smooth without using extra cement

M & L preparing new plastered surfaces and applying three coats of white wash on ceiling

M & L preparing new plastered surfaces and applying two coats of cement base paint on wall

M&L preparation of newly plastered surface wall and applying two coats of distemper oil emulsion of any tint over a coat of primer complete all as specified and directed.

Demolition of cement concrete in ground floors and pavings not exc 15cm thickness (below or above ground level)

Dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing), removing serviceable tiles to store and rubbish off the premises

M&L 25 mm thick plain cement concrete type B-0, 1:2:4 (12.5mm graded aggregate) as in floor all as specified

M & L coloured non skid ceramic tiles 300x300x7mm thick in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over & including 15mm thick screed bed in CM 1:6 complete.

M & L glazed coloured ceramic tiles 300x200x7 mm thick, on vertical surfaces of wall such as dado, skirting etc set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 10mm thick screed bed in CM 1:4 complet.

M & L coloured glazed ceramic joint free tiles 400x400x7 to 8mm thick in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over & including 15mm thick screed bed in CM 1:6 complete all as approved and directed

M & L coloured glazed joint free ceramic tiles 400x400x7 to 8mm thick in vertical surface as in skirting over & including 10mm thick rendering on stone masonry surfaces or surfaces other than fair faces of brick work in CM 1:4 complete all as approved and directed

M & L Vitrified Ceramic tiles 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc, set over 15mm thick screed in CM 1:6 jointed in neat cement slurry and pointed in white or coloured cement to match ,light shade.

M & L Vitrified Ceramic tiles 10mm thick (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm,on vertical surfaces such as skirting, dados and risers to steps ,wall etc set over 10 mm thick cement plaster in CM 1:4 and jointed in neat cement slurry and pointed in white or coloured cement to match colour of the tile.

M & L preparing old plastered surfaces and applying two coats of white wash on ceiling

M & L complete removal of existing treatment from surface of the walls and applying two coats of cement base paint on wall

M&L preparation of old decorted surface of walls and applying one coat of distemper oil emulsion of any tint all as specified and directed.

M & L PCC 1:2:4 type B1 (using 20 mm graded stone aggregate) in coving at juction of chajja/slab and wall/ lintel/ beam finished even and smooth in any situation and position including form work complete

Demolition of stone or brick masonry built in cement mortar or cement lime mortar incl all quoins, arches, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles

M & L Brick work with sub class ‘B’ bricks straight or curved on plan exc 6 mtr mean radius using old size brick built in CM 1:6

M&L scrapping roof surface with wire brushes and washing with water etc including taking down old cement plaster, PCC of any thickness, description in any situation ,position and roof treatment any type for making good to receive new roof treatment any type. and removal of same from site to out side of MOD land complete all as specified and directed.

M&L screed bed or bedding layer of 15mm thick in CM 1:6 for laying floor finishes in roof, finished even and smooth without using extra cement complete all as specified & as directed.

M&L for preparing RCC roof surfaces and providing 10 mm thick modifyed plaster in CM 1:4 cement mixed with polymer in ratio of 1:10 i.e. 1 part of polymer and 10 parts of cement applying priming coat of epoxy primer with resin and hardener with water dilution as per manufacturer instructions , applying two coat of solvent ased polyurethene liquid memrane not less than 500 micron thick UV stale having SRI value greater that equal to 105 with consumption of 0.61 kg/Sqm (each coat) 2nd coat should be applied once 1st coat it is dry. Make ; Berger Paint, Asian paints/thermax or equivalent make as approved.

M&L painted cement plastered surfaces with one coat of cold applied bituminous primer @ 0.40 ltr/Sqm conforming to IS-3384 and laying APP based polymeric membrane not less than 3mm thick, weighing not less than 3.5kg/sqm, reinforced with polyester non woven fabric (weighing not less than 150gms/sqm) shall only be used. It shall be laid by torch application. Side over laps shall be 75mm and the end lap shall be 100mm and all over laps and joints shall be sealed by torch application. For parapets, membrane shall be taken to a height of minimum 60cm and then inserted inside the parapet groove. This shall be finished by a membrane flashing.

M&L for marble crezy over 20mm the screed in CM 1:4 shall be laid over surface obtained after fine sand dusting. When the cement is still green, 18-20mm thick marble crazy pieces shall be spread in regular panel using dividers of marble strips 18-20 mm thick and 50mm wide the size of panels shall be 1.0 to 1.50 m in length and breadth spread over the entire roof area so that 80-85% area of roof is covereed by these piecses leaving joints 10 to 15 mm vide the spece for joints shall be filled with cement sands and marble agg of 4 to 7mm size like in " cast in situ tarrazo topping" the work of placing curing and grinding shall be done all as per clause 13.38.4 to 13.38.6 of SSR Part-I

M&L preparation of APP based polymeric surface and applying two coat of aluminium paint all as specified & as directed.

M&L padding in PCC 12:4 type B-0 ( using 12.5mm size graded stone aggregate) laid to provide a finished slope of 1:30 finished even and smooth without using extra cement all as specified

M&L for applying two coat of Dr fixit new coat on plastered surface or concrete surface including preparation of surface dust free, oil free etc(Note : The hair line crack/pours etc to be sealed by applying Dr fixit chemical.)

Dismantling of wall and ceiling boards (fiber, pulp, insulation etc) or insulation board slabs etc any thickness incl cover fillets.

S&F aluminium anodised snap grid false ceiling frame of size 605 x 605 mm frame work for false ceiling all as specified .

M&L 12 mm thick Perforated particle board/tiles for insulation and accoustic purposes, 60x60 cm in size, fixed with nails to frame work or with staples on snap grid .

M&L for hanger 6mm dia GI (upto 1200mm length) adjustable level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x3mm size 60mm long and expansionhold fasterner 12.5mm dia 40mm long complete.

Dismentaling of asbestos cement (corrugated or semi corrugated) sheet in roof covering.

S&F rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates including welding FE -290 Gde E-165

S&F Pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall,fixed with self tapping screws as specified.

Schedule of Credit

M/S Chandra Mohan Bansal

UNIVERSAL INFRAPROJECT PVT LTD

M/S Mohan Lal Gupta

S.R.Enterprises

J.J.ENGINEERING