Construction of waiting lounge for passenger facilitation at Arjun Nagar gate of Air force Station, Agra

Amount

SH: - 1 - EARTH WORK

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, lead upto 50m. All kinds of soil

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soil.Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

Extra for every additional lift 1.5m or part there of in excavation / banking excavated or stacked materials - All kinds of soil

Supplying and filling in plinth with Local sand (zone-V) under floors, including watering, ramming, consolidating and dressing complete.

Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including disposal of excavated earth upto 50 m and lift upto 1.5 m, disposed soil to be levelled and neatly dressed : All kinds of soil

SH: - 2 - CONCRETE WORK

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing: 1:5:10 (1 cement : 5 coarse sand (zone-III) : 10 graded stone aggregate 40 mm nominal size).

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor,etc., up to floor five level, excluding the cost of centering, shuttering and finishing: 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III): 4 graded stone aggregate 12.5mm nominal size).

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

SH: - 3 - R.C.C. WORK

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Centering and shuttering including strutting, propping etc. and removal of form for :Foundations, footings, bases of columns etc. for mass concrete.

Centering and shuttering including strutting, propping etc. and removal of form for all heights : Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Centering and shuttering including strutting, propping etc. and removal of form for :Suspended floors, roofs, landings, balconies and access platform.

Centering and shuttering including strutting, propping etc. and removal of form for :Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Centering and shuttering including strutting, propping etc. and removal of form for :Columns, Pillars, Piers, Abutments, Posts and Struts.

Extra for additional height in centering, shuttering where ever required with adequate bracing propping, etc. including cost of deshuttering and decentering at all levels ,over a height of 3.5 m for every additional height of 1m or part there of (plan area to be measured) Suspended floors, roofs, landing, beams and balconies (plan area to be measured)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work, and cement content as per approved design mix, and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work, including pumping of R.M.C. from transit mixer to site of laying, excluding the cost of centering, shuttering, finishing and reinforcement, including cost of admixtures in recommended proportions as per IS : 9103 to accelerate / retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. (Note :- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/recoverable separately). a) All work up to plinth level

Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work, and cement content as per approved design mix, and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work, including pumping of R.M.C. from transit mixer to site of laying, excluding the cost of centering, shuttering, finishing and reinforcement, including cost of admixtures in recommended proportions as per IS : 9103 to accelerate / retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. (Note :- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/recoverable separately). b) All works above plinth level upto floor V level

Extra for providing richer mixes at all floor levels. Note:- Excess/less cement over the specified cement content used is payable /recoverable separately. Providing M-30 grade concrete instead of M-25 grade BMC/ RMC. (Note:- Cement content considered in M-30 is @ 340 kg/cum)

Add for using extra cement in the items of design mix over and above the specified cement content therein.

SH: - 4- BRICK WORK

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand)

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry.

5 - MARBLE & GRANITE WORK

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade - Area of slab over 0.50 sqm

Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete.

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-charge. Granite work

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providng and fixing Ist Quality 18mm thick mirror polished granite stone in skirting, dado and cladding fixed on 12mm (average) thick cement mortar 1:3 (1 cement : 3 coarse sand) and jointed with white cement slurry mixed with pigment to match the shade of slab including curing, cleaning complete at all levels. a) Mirrior polished granite stone slab of any approved colour and shade

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or quivalent.

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Extra for providing and applying minimum two coats of Ferrocrete/Leticrete Sealer or approved equivalent on the back surface and sides of the Granite with a brush or roller to act as a barrier coat against stains, soling, discoloration and effloroscence including cleaning the surface with brush or roller, mopping with moist cloth and allowing it to dry before application all complete as per direction of Engineer-in-charge.(Raw Surface) Note : Granite stone flooring shall be paid for separately under respective item.

Extra for providing and applying minimum two coats of Ferrocrete/Leticrete Impregnator sealer or approved equivalent with a brush / roller on the top surface and sides of the Granite to act as a barrier coat against stains, soling, discoloration and effloroscence including cleaning the surface with brush or roller, mopping with moist cloth and allowing it to dry before application all complete as per direction of Engineer-in-charge.(Polished Surface). Note : Granite stone flooring shall be paid for separately under respective item.

SH: - 6 - WOOD AND PVC WORK

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.0 mm thick

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing stainless steel sliding door bolts of approved brand with nuts and screws etc. complete: 250x16 mm

Providing and fixing stainless steel handles approved brand with necessary screws etc. complete : 125 mm

Providing and fixing stainless steel tower bolts of approved brand with necessary screws etc. complete: 250x10 mm

Providing and fixing stainless steel tower bolts of approved brand with necessary screws etc. complete: 150x10 mm

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. Twin rubber stopper

Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with zinc coating of 120 ms/sqm(both side inclusive), consisting of floor and ceiling channel 50mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x 0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture’s specification and direction of engineer in charge all complete. Continued....

66mm overall thickness partition using 8mm thick double skin non- asbestos multipurpose cement board reinforced with cellulose fibre manufactured through autoclaving process (High pressure steam cured) as per IS : 14862 with suitable fibre cement screws

Providing and fixing cup board shutters with 25 mm thick veneered particle board IS : 3097 marked, exterior grade (Grade I), of approved make, including IInd class teak wood lipping of 25 mm wide x 12 mm thick with necessary screws and bright finished stainless steel piano hinges, complete as per direction of Engineer-in-Charge. a) With decorative veneering on one side and commercial veneering on other side.

SH: - 7 - STEEL WORK

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Electric resistance or induction butt welded tubes.

Providing and fixing mild steel round holding down bolts with nuts and washer plates complete.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. a) In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing & fixing welded steel wire fabric of required width rectangular mesh ( Grid size 70x25mm) including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted etc. all complete.

SH: -8 - FLOORING

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate

Providing and laying vitrified floor tiles in different sizes (thickness 8mm to 10 mm) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 600x600 mm

Providing and laying Vitrified tiles in different sizes (thickness 8mm to 10 mm), with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer, in all colours and shade, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately). a) Size of Tile 600x600 mm

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

SH: -9 -ROOFING AND CEILING SYSTEM

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin- charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, - Single socketed pipes 160 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Coupler 160 mm

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. Bend 87.5°-160 mm bend

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recomme-nded jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer’s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with 12.5 mm thick tapered edge gypsum moisture resistant board

Providing and Fixing 15 mm thick densified regular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture spintone/cosmos / Hexa or equivalent of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main 'T' runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross "T" of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main'T' at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross 'T' of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calcium silicate ceiling tiles of approved texture (Spintone / Cosmos/hexa) in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main 'T' runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main 'T' , bottom exposed with 24 mm of all T-sections shall be pre-painted with polyester baked paint, for all heights, as per specifications, drawings and as directed by engineer-in-charge. Continued...

Note :- Only calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be made for exposed frames/opening (cut outs) having area less than 0.30 sqm. The calcium silicate ceiling tile shall have NRC value of 0.50 (Minimum), light reflection > 85%, non - combustible as per B.S. 476 part IV, 100% humidity resistance and also having thermal conductivity <0.043 w/m 0 KC.

Supply, Fabrication, Erection and installation of on-site single length color coated Standing Seam profile of Tata Blue Scope / Lloyd / JSW Steel / TATA BSL/ Blue scope, multi-colour , double structural architectural insulated multi zip standing seam steel roofing system; of nominal 400-450 mm effective cover width with two - three stiffener symmetrically spaced between ribs and standing seam height of 62-65 mm /as approved. The panel shall be concealed fixed with aluminium clip having 3 mm thermal pad, mechanically field seamed for increased weather durability and greater resistance to wind uplift. The feed material is manufactured from 0.55 mm Base Metal thickness (0.60 mm TCT), min. 300 MPa yield strength coated with hot dip metallic AluminiumZinc alloy coating, AZ150 (150 gms/sq.mt total on both sides) confirms to AS 1397 with Super Durable Polyester/ SMP or approved equivalent quality paint conforms to AS/NZS 2728 Class 3 of approved make having the license of Bethlehem International Engineering Corporation (BIEC) or relavent licencing authority. The coated steel shall be factory painted and oven baked with total coating thickness of nominal 35 μm, comprising of nominal 20 μm exterior coat on top surface and nominal 5 μm reverse coat on back surface over nominal 5 μm primer coat on both surfaces of approved colour shade by Engineer-In-Charge. The standing seam sheet panel Tata Blue Scope / Lloyd / JSW Steel / Blue scope, multi-colour shall be fixed on to the galvanized Z sub purlin, using extruded structural grade aluminium clips (Aluminium alloy 6005 A/ 6063-T5)/G.I. Clips fixed over minimum3 mm thick thermal pad. The head of clips shall be accurately matches the roof sheeting to ensure the sheet slides freely during thermal movement. The insulation shall be 100 mm thick (laid in two layers of 50mm with vapour barrier) fiberglass with minimum density 24 kg/m3 or Rockwool with minimum density 48 kg/m3 to achieve minimum U value of 0.26 W/m2 K, as approved by Engineer-In-Charge. Continued...

The liner sheet is manufactured from 0.45 mm base metal thickness (BMT) and 0.50 mm total coated thickness (TCT). The panel shall be minimum 15 % (or as per Engineer -in -Charge) perforated backed with Non woven acoustic tissue paper, for acoustic properties. The panel shall be of 980-1015mm effective cover width, 28-30mm rib height, 186- 250 mm pitch, manufactured out of Hi tensile pre-painted sheet steel Zinc Aluminium Alloy coating-AZ150 (min. 150 gms/sq.mt total on both sides), G300 or G550 Grade, with Super durable Polyester /SMP or approved equivalent quality paint coat as per AS/NZS 2728 Class 3 of make as per the list of approved makes having the license of Bethlehem International Engineering Corporation (BIEC) or relevant licencing authority. The coated steel shall be factory painted and oven baked with total coating thickness of nominal 35 μm, comprising of nominal 20 μm exterior coat on top surface and nominal 5 μm reverse coat on back surface over nominal 5 μm primer coat on both surfaces of approved color shade by Engineer-in-charge. The item includes supply, fabrication and installation of 3mm thick aluminium (grade AA 1100) gutter with welding, all necessary accessories and fasteners to complete the system water tight.The concealed clip and bottom panel profile sheet shall be fastened with min. 25 μm Zinc-Tin alloy coated, Hex head, self-drilling screw as per AS 3566-2002 Class 3 fasteners of approved make (Buildex / Corroshield/ EJOT ). The fastener size shall be calculated as per the design. The supplier and applicator shall have the necessary ISO 9001:2000, 14001:2004 &OHSAS 18001 certification or relavent certification. The insulation material should conform to ECBC /GRIHA recommendation. Continued...

The two sheets shall sandwich with 100 mm thick (laid in two layers of 50mm) Glass wool 24 kg/m3 or Rockwool with minimum density 48 kg/m3 insulation in two layers to achieve minimum U value of 0.26 W /mK and SITC of 39 db. A Vapour barrier of 400 gauge polythene sheet should be provide over the insulation. The entire Double skin system is installed over the structure purlin. The measurement shall be based on finished/covered surface area. The contractor shall prepare the shop drawings based on the drawings supplied by the Engineer-in-charge for approval. The rate shall includes for flashings, sealants and work shall carried out by specialized agency. (The erection / fixing / installation shall be done by specialized agency as approved by AAI) (Item includes supplying, installation and fixing of profiled metal sheeting including cost of system accessories insulation, vapour barrier, liner sheet, flashing, fasteners, gaskets, brackets screws rivets, sealants, inner closure fillers, fixtures etc complete, all machineries and all taxes, i.e. sales tax, excise duty, customs duty, GST etc.). The above work shall be carried out by an agency having sufficient experience in concerned work and should ensure a guarantee for any defective installation, material composition and water tightness for a period of 10 years from the date of completion of the said work .Only skilled and experienced persons shall be employed for this purpose.

Providing and fixing,Flashing & Ridge Capping of plain colour coated fabricated sheet to the required size of minimum 0.60 mm TCT cold rlled steel of 550Mpa (min) yield strength confirming to ASTM A368 or AS 1595, metallic hot dip coated with zinc-aluminium alloy coating on both side (55% Aluminium, 43.5% Zinc,1.5%silicon) as per ASTM A792 or AS1397.The colour coating shall have a total coating thickness of 35μm polyester paint system as per AS/NZS-2728:1997 of approved colour, comprising of 20μm exterior coat on top surface and 5 μm reverse coat on back surface over 5μm primer coat on both surfaces of approved colour shade by Engineer-In-Charge.The flashing/Ridge capping shall be fixed using galvenised imported self drilling and self tapping fasteners with EPDM washers for perfect sealing etc complete as directed by Engineering in charge. (Item includes designing, supplying, installation and fixing of metal sheet including cost of system accessories flashing, fasteners, gaskets, brackets screws rivets, sealants, inner clousre fillers, fixtures, all achineries,carriage,all lead &lift,scaffolding and all taxes, i.e sales tax, excise duty, customs duty, GST etc.) The above work shall be carried out by an agency having sufficient experience in concerned work and should ensure a guarantee for any defective installation, material composition and water tightness for a period of 10 years from the date of completion of the said work .Only skilled and experienced persons shall be employed for this purpose. Flashing & Ridge Capping of plain of width 60 cm overall width.

SH: - 10 - FINISHING WORK

12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand)

15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement: 6 fine sand)

15 mm cement plaster 1 : 3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement on the rough side of single or half brick wall.

6 mm cement plaster of mix : 1:3 (1 cement: 3 fine sand)

White washing with lime to give an even shade: New work (three or more coats)

Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer’s specifications including appropriate priming coat, preparation of surface, etc. complete. - On steel work

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade. Two or more coats on new work.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

SH: -11 - ROAD WORK

Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30

Construction of dry lean cement concrete sub base over a prepared sub-grade with coarse and fine aggregate conforming to IS:383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per specifications, cement content not to be less than 150 Kg/cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, for all leads & lifts, laid with a mechanical paver, compacting with 8-10 tonne vibratory roller, finishing and curing etc. complete as per direction of Engineerin- charge.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature jointed with cement mortar 1:3 (1 cement : 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-Charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in- Charge).

Providing and laying factory made chamfered edge Cement Concrete paver blocks In foot path, park & lawns driveway or light & traffic parking etc. of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of course sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, all complete as per manufacturer's specifications & direction of Engineerin- Charge. 80mm thick Cement concrete paver block of M-30 grade with approved colour, design & pattern.

Providing and laying matt finished vitrified tile of size 100x100x16mm having water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in out door floors such as footpath, court yard multi models etc., laid on 20mm thick base of cement mortar 1:4 (1cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as direction of Engineer-in-Charge

SH:- 12.0 SANITARY FIXTURES

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board - 510x1040 mm bowl depth 250 mm

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing toilet paper holder : C.P. Brass

Providing and fixing soil, waste and vent pipes : 100 mm dia -Sand cast iron S&S pipe as per IS: 1729

Providing and fixing soil, waste and vent pipes : 75mm diameter - Sand cast iron S&S pipe as per IS: 1729

Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. : For 100 mm dia pipe

Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 100 mm dia- Sand cast iron S&S as per IS - 1729

Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 100x100x100 mm Sand cast iron S&S as per IS - 1729

Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 75 mm dia- Sand cast iron S&S as per IS - 1729

Providing and fixing single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. 75x75x75 mm Sand cast iron S&S as per IS - 1729

Providing and fixing plain bend of required degree. 100 mm dia- Sand cast iron S&S as per IS - 1729

Providing and fixing plain bend of required degree. 75 mm dia - Sand cast iron S&S as per IS - 1729

Providing and fixing single equal plain junction of required degree : 100x100x100 mm - Sand cast iron S&S as per IS - 1729

Providing and fixing single equal plain junction of required degree : 75x75x75 mm - Sand cast iron S&S as per IS - 1729

Providing and fixing collar : 100 mm - Sand cast iron S&S as per IS - 1729

Providing and fixing collar : 75 mm - Sand cast iron S&S as per IS - 1729

Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter - 100 mm

Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter - 75 mm

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 100 mm inlet and 100 mm outlet - Sand Cast Iron S&S as per IS: 1729

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors : 100 mm inlet and 75 mm outlet - Sand Cast Iron S&S as per IS- 1729

Cutting chases in brick masonry walls for following diameter sand cast iron/ centrifugally cast (spun) iron pipes and making good the same with cement concrete 1:3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 12.5 mm nominal size), including necessary plaster and pointing in cement mortar 1:4 (1 cement : 4 coarse sand) : - 100 mm dia

Cutting chases in brick masonry walls for following diameter sand cast iron/ centrifugally cast (spun) iron pipes and making good the same with cement concrete 1:3:6 ( 1 cement : 3 coarse sand :6 graded stone aggregate 12.5 mm nominal size), including necessary plaster and pointing in cement mortar 1:4 (1 cement : 4 coarse sand) : - 75 mm dia

Providing and fixing white vitreous china extended wall mounting water closet of size 780x370x690 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/6 litre (adjustable to 4 litre/8 litres), including seat cover, and cistern fittings, nuts, bolts and gasket etc complete.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

Providing & fixing white vitreous china water less urinal of size 600 x 330 x 315 mm having antibacterial /germs free ceramic surface, fixed with cartridge having debris catcher and hygiene seal.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps.

Providing and fixing CERA / Hindware or equivalent make Oval shape wash basin with 15 mm C.P. brass swan neck pillar tap,32 mm C.P. brass waste of standard pattern, including cutting and making good the venity counter wherever require: White Vitreous China Oval shape Wash basin size 550x400 mm with 15 mm C. P. brass swan neck pillar tap.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe.32 mm dia

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineerin- charge.

Providing and fixing in position Hindware make or Equivalent Health faucet with Rubbit Cleaning System 1.20M Long Pvc Flexible Tube &Abs Wall Hook for EWC at all heights, levels, including cost of all material complete in all respect as per manufacturer's specifications and satisfaction of Engineer In-charge including cutting and fitting in position where ever required.

Providing and fixing of 32 mm dia x 600 mm long grab bar made of stainless steel of make Jaquar or equivalent complete as per satisfaction of Engineer-in-Charge.

Providing & fixing Soap dispenser of Make BETTER LIVING PRODUCTS 420ML & Model No. 71150 or equivalent as per direction & satisfaction of Engineer-in-charge.

SH:- 13.0 WATER SUPPLY

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall - 40 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 32 mm nominal outer dia Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. - 25 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. - 32 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching ,refilling & testing of joints complete as per direction of Engineer in Charge. External work 62.50 mm nominal inner dia Pipes.

Making connection of G.I. distribution branch with G.I. main of following - sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 25 to 40 mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 50 mm nominal bore.

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 65 mm nominal bore each

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete : 25 mm

Providing and fixing gun metal non- return valve of approved quality (screwed end) : 40 mm nominal bore - Vertical

Providing and fixing gun metal non- return valve of approved quality (screwed end) : 65 mm nominal bore - Horizontal

Providing and fixing gun metal non- return valve of approved quality (screwed end) : 80 mm nominal bore - Horizontal

Providing and fixing uplasticised PVC connection pipe with brass unions : 45 cm length 15 mm nominal bore

Constructing masonry chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C.I. surface box 100x100x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design. a) With common burnt clay F.P.S. (non modular ) bricks of class designation 7.5

Constructing masonry chamber 90x90x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1: 3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design. With common burnt clay F.P.S. (non modular ) bricks of class designation 7.5.

Constructing masonry chamber 120x120x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.1. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement :2 coarse sand : 4 graded stone aggregate 20mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand :10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design. With common burnt clay F.P.S. (non modular ) bricks of class designation 7.5.

Constructing masonry chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for fire hydrants, with C.I. surface box 350x350 mm top and 165 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design. With common burnt clay F.P.S. (non modular ) bricks of class designation 7.5.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. Circular tank

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 a) 15 mm nominal bore 15 mm nominal bore

Making chases up to 7.5x7.5 cm in walls including making good and finishing with matching surface after housing G.I. pipe etc.

Making hole up to 20x20 cm and embedding pipes up to 150 mm diameter in masonry and filling with cement concrete 1:3:6 (1 cement: 3 coarse sand 6 graded stone aggregate 20 mm nominal size) including disposal of malba.

SH:- 14 DRAINAGE

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300x300mm size (inside) the weight of cover to be not less than 4.50 Kg and frame to be not less than 2.70 Kg as per standard design. 150 x 100mm size P type with common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 250 mm dia. R.C.C. Pipe

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 300 mm dia. R.C.C. pipe

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (heavy duty) 560 mm internal diameter, total weight of cover and frame to be not less than 208 kg (weight of cover 108 kg and weight of frame 100 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth for manholes : Size 120x90 cm - With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

SH: - 15 - GLAZING AND ALUMINIUM WORK

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion - Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) - Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-laminated particle board with decorative lamination on both sides

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item) : With float glass panes of 5.0 mm thickness (weight not less than 12.50 kg/ sqm)

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315,having brand logo embossed on the body/plate with double spring, mechanism and door weight upto 125kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc.complete as per the direction of engineer in charge. With stainless steel cover plate minimum 1.25 mm thickness

Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete. Upto 5mm depth and 5 mm width

Providing and fixing 12mm thick toughened glass partiton supported at bottom on floor and sides to stainless steel framing with all necessary fittings and fixtures of approved make (dorma, ozone or equivalent) including glass preparation, cutting holes, countersunk holes as per fittings and filling the gaps with silicon sealant complete as direction by Engineering-in-Charge.

Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. (The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account). The weight of aluminium extruded section shall be taken for purpose of payment.

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: (a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required, proper drainage of water to make it watertight including checking of all the structural and functional design. (b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of 4mm thick aluminium composite panel material consisting of 3mm thick FR grade mineral core sandwiched between two Aluminium sheets (each 0.5mm thick). The aluminium composite panel cladding sheet shall be coil coated, with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer (Service) coating on face # 2 as specified using stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc. Continued...

(c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour component, the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding is payable under the relevant aluminium item.s The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places.

Design, Supply and fixing structural glazing system consisting of powder coated aluminium and glass of approved make, aluminium frame work fabricated out of heavy duty Aluminium extruded profile powder coated with durable thermosetting polyester powder coating by electrostatic spraying and hard stoved to not less than 60 micron thickness to comply with BS 6496:1994 (1991) and AAMA 2603-98 standard as per approved shade. All aluminium members and profile shall be of AC-25grade as specifications. The aluminium members shall be protected with protections tapes all around the profile for safety against external scratches at site. (Protection tape shall be removed only at a time of handing over as per the instructions of project management.). The anchoring /bracing of the glazing to the RCC slabs /beams /colums shall be done with required number of non corrosive galvanized extended brackets of approved design (Galvanizing to be done con-forming to IS: 4759-1996 upto 610 gms per sqm, 80-90 mcirons thickness) with ap-proved dash fasteners of the minimum 12mm dia and depth of minimum 100mm, in the concrete and stainless steel bolts including providing and fixing aluminium shims of var-ious thickness to adjust the beam level and line variation. Continued...

The anchoring system shall be designed to withstand the dead load of structural wall as well as stresses due to wind pressure etc. The glazing frame shall be aligned for each vertical mullion for the entire height and for each transom for the entire width horizontally by laser beam equipment to ensure 100% x axis and y axis alignment. To make the joint water and air tight the glazing frame work provided with approved in built ventilation and drainage system. All the joints of the structural glazing system and the periphery, of glass shall be properly sealed with specified weather silicon. The details of inbuilt ventilation and drainage system should be submitted by the contractor before execution. EPDM gasket of suitable profile to accommodate glasses in all vision areas shall be pro-vided at all glazing area to make the glazing water and air tight. Including the glass to be fixed at the outer side of the aluminium frame with structural silicon sealant (SG 18/ DC995) and mechanical support with pressure plates and cover plates(the structural sili-con bite size shall not be less than 8mm/ as per the structural requirement/as per manu-facturers recommendation). Expansion joint gap for mullion shall be minimum 15 to 20mm to be provided where ever required, filled with expansion joint sealant from wacker, Dow corning DC 789/Sikka or equivalent. All screws, washers used shall be only stainless steel 316 grades and through, Bolts, Nuts and Anchors used shall be only stainless of 316 grades etc. complete as per direction of EIC. (The structural design &drawings shall be provided by AAI/ Consultant however the executing agency has to submit shop drawings and mock-up based on same which have to be approved by EIC before start of work.) 1) Mullions & Transoms, extruded aluminium sections shall be of 6063-T6 alloy to be as per structural calculations of Jindal/Bhuraka or approved equivalent. Continued...

2) Coating of aluminium section will be powder coated with durable thermosetting po-lyester powder coating by electrostatic spraying and hard stoved to not less that 60 mi-cron thickness to comply with BS 6496-1994 (1991) and AAMA 2603-98 standard of approved shade as per direction of EIC. 3) Heavy duty, best quality EPDM gasket at joints and connection between Aluminium members. 4) All components should be sealed for water proofing with silicon of wacker, Dow corning of DC 789 /Sikka or equivalent or water proof membranes with internal/external aluminium flashing finished to approval. Curtain wall should be seal to hoist structure and allow movements etc. in its service life. Item includes cost of Design,supplying, installation and fixing of aluminium frame with structural members, mullions, Transom, sub fame, fixtures etc, including supply installation and fixing glass including cost of sealants, brackets, fasteners, screws, sleeve, spacer tape, backer rod, bolts, gasket, fixtures, scaffolding, sales tax/ GST, excise duty, any other taxes etc. complete in all respect at all heights. (The work is to be carried out by a specialized agency approved by the EIC.) (Cost of M.S. structural steel framework shall be measured and paid separately.) a) Hermetically sealed DGU System shall be fixed for cityside & airside at Ist floor consisting of 6mm thick Dark Blue/ Super silver blue high performance heat soaked toughened glass +12mm air gap + 6mm thick clear heat soaked toughened glass as per specification fixed in precise size on the outer infill panel of make Saint Gobain/ Asahi/Emirates glass or equivalent, High performance glass U value-1.5 to 2.0 Watt/m2K, SF-0.20 to 0.25 & VLT-35-45% etc.

Providing and fixing handicapped sliding fittings for door with aluminium sections of size 1.8mx2.1m of Dorma SLM 120 Sliding door system or equivalent with SLM 120 accessories, SLM Track etc all complete as per manufacturer's technical specification as directed by engineer in charge .The rate is Inclusive of cost,carriage of all materials like track for sliding,all hardwares,sliding fittings,lock,handles etc , labour charge, lead & lift, all taxes complete. ( For door shutter will be paid separatly)

Providing & fixing modular toilet cubicles of Merino / Greenply or equivalent), (of following standard dimension which includes 600mm door size width) made of heat, bacteria, water, chemical, scratch, impact and anti bacterial resistant 12mm thick solid compact laminate panels including doors, pilasters & intermediate panels finished with approved texture/shade as per the detail drawings & as per IS 2046 (Indian Standard) and as per fire retardant BS-476/97 standard. This also includes providing and fixing in position necessary hardware made out of Stainless steel (Grade 304) as per manufacturer’s specifications & Architects instructions like (1) Door Knob, (2) Gravity Hinges, (3) Thumb turn lockset with Occupancy indicators, (4) Coat hooks with Door stopper (5) U- Channels, (6) Adjustable foot/pedestal, (7) Top rail with Corner connector (8) Rubber noise deafening tape, (9) Screws & wall Plugs. Continued...

The top fitting should consist of SS round top rail which will get fixed with pilasters, with SS panel tube holder, SS corner bend (connected with top rail) will be used on the corner of cubicle in absence of brick wall, SS wall fixing is used only on the wall which will hold the ss top rail. All screws will of 304 Grade in stainless steel with satin finish. All pilasters are supported by stainless steel Adjustable Foot. The base of the stainless steel bottom cladding will be anchored to the floor with a clearance height up to 150mm. a) Toilet Cubicle L-shape with standard dimension of 2000 - 2100 mm Height x 900 mm Width x 1500mm Depth, which includes 600mm door size width).

Providing & fixing modular toilet cubicles of Merino / Greenply or equivalent), (of following standard dimension which includes 600mm door size width) made of heat, bacteria, water, chemical, scratch, impact and anti bacterial resistant 12mm thick solid compact laminate panels including doors, pilasters & intermediate panels finished with approved texture/shade as per the detail drawings & as per IS 2046 (Indian Standard) and as per fire retardant BS-476/97 standard. This also includes providing and fixing in position necessary hardware made out of Stainless steel (Grade 304) as per manufacturer’s specifications & Architects instructions like (1) Door Knob, (2) Gravity Hinges, (3) Thumb turn lockset with Occupancy indicators, (4) Coat hooks with Door stopper (5) U- Channels, (6) Adjustable foot/pedestal, (7) Top rail with Corner connector (8) Rubber noise deafening tape, (9) Screws & wall Plugs. Continued...

The top fitting should consist of SS round top rail which will get fixed with pilasters, with SS panel tube holder, SS corner bend (connected with top rail) will be used on the corner of cubicle in absence of brick wall, SS wall fixing is used only on the wall which will hold the ss top rail. All screws will of 304 Grade in stainless steel with satin finish. All pilasters are supported by stainless steel Adjustable Foot. The base of the stainless steel bottom cladding will be anchored to the floor with a clearance height up to 150mm. a) Toilet Cubicle I-shape with standard dimension of 2000 - 2100 mm Height x 900 mm Width x 1500mm Depth, which includes 600mm door size width).

Providing & fixing of Urinal modular partition of make Merino/ Greenply or equivalent,consisting of 12mm thick compact laminate with HPL Board in single colour and size of 1200mm(H)x500mm(D).Including Besco Make SS hardware for fixing the divider to the wall etc complete as directed by Engineer in charge. The rate is Inclusive of cost,carriage of all materials, labour charge, lead & lift etc complete.

Supplying and installation of 12 mm thick frameless toughened clear glass door consisting, hardware of Dorma-Germany / Linox-Australia / Geze - Germany or approved equivalent and 12mm thick toughened clear glass of any required size of ASAHI/Saint Gobain / Emirates or approved equivalent. Glass to be toughened by special chemical to strengthened by double impact, all edge to be machine polished and sides also to be toughened. The work also includes cutting of floor (15mm strip of size 15mm X 15mm) for floor spring of Dorma heavy floor spring BTS 84 - Dorma / FS 004 - Linox / TS 500 NV of Geze or approved equivalent to hold the glass at bottom. The work includes cost of all cut outs/holes wherever required including fixing of hardware consisting of all required patch fittings for doors with side and upper panels, upper and bottom patches, floor lock with cylinder and strike plate and SS-316 pull handle of size 450mmX22mm complete as per direction of Engineer-In-Charge

SH: - 16 - Water Proofing

Providing,Mixing & Laying of Fosroc Conbextra GP2 for grout the MS column base plate as per manufacture specification in i/c cenetring , shuttering etc.

SH: - 17 - ENGINEERING CONSULTANCY

Providing Engineering Consultancy for civil, electrical works and other services catered in this contract as per provisions of NBC and other relevant codes for preparation of detailed working drawings, shop drawings and drawings for different services like water supply, sewage system, fire hydrant etc. i/c preparation of structural designs and drawing & Vetting of drawings / design from Govt. Institute ( I I T BHU OR equivalent ), (refer technical specifications for this item TSC section). Note: Soil Investigation for building work is to be carried out by AAI and report will be provided to the agency.

SH: 18- LIGHT FITTING & FIXTURES

Supply of 40/42 W LED, light fixture including driver suitable for surface/recess mounting 2'x2' LED, powder coated extruded aluminium /standard alloy housing, comprising of LED’s of approved make, and as per specifications complete as required. (Similar to Havells CAT No. VENUS NEO HE 2X2 or equivalent)

Supply of 28W LED, light fixture including driver suitable for surface/recess mounting 2'x2' LED, powder coated extruded aluminium / standard alloy housing, comprising of LED’s of approved make, and as per specifications complete as required. (Similar to Havells CAT No.VENUS NEO HE 2X2 or equivalent)

Supply of 24W LED canopy downlighter fitting including driver suitable for surface/recess mounting (round/square type), powder coated pressure die cast aluminium heat sink, comprising of LED’s of approved make, and as per specifications complete and as required (Similar to Havells CAT No. INTEGRA NEO or equivalent)

Supply of 12/15W LED Down lighter fitting including driver suitable for surface/recess mounting (round/square type), powder coated pressure die cast aluminium heat sink, comprising of LED’s of approved make, and as per specifications complete and as required (Similar to Havells CAT No. INTEGRA NEO or equivalent)

Supply of 10W /12 W LED tubelight 2 feet, including driver with aluminium housing suitable for surface mounting including batten etc. as per specification, complete as required.(Similar to Havells CAT No. LUMILINE PLUS or equivalent)

Supply of 20/22W LED tubelight fitting 4 feet, (Appox.) including driver with aluminium housing suitable, suitable for surface mounting including batten etc. as per specification complete, as required. (Similar to Havells CAT No. LUMILINE PLUS or equivalent)

Supply of 300 mm, 900 RPM heavy duty exhaust fans with louver suitable for 230 volt for the existing opening of the porta cabin/washrooms, complete as required. (similar to Havells Model- Turbo Force or equivalent), as per AAI approved make list.

Supply of 250 mm non metalic,1200 RPM ventilating fan/ exhaust fans with louver, suitable for 230 volt for the existing opening of the porta cabin washrooms etc, complete, as required. (similar to - Havells Model- Ventiliar DX White or equivalent) , as per AAI approved make List.

Supply of 400mm dia sweep wall fan Oscillating type complete with built in String type speed regulator and mounting arrangement.complete, as required. (Similar to Havells make -Sameera or equivalent) as per AAI approved make list.

Supply of 450 mm, 900 RPM heavy duty exhaust fans with louver suitable for 230 volt for the existing opening of the porta cabin/washrooms, complete as required. (similar to Havells Model- Turbo Force or equivalent), as per AAI approved make list.

Supply of 1200 mm 5 star energy efficient ceiling fan with double ball bearing, Aluminium pressure die cast body with Aluminium blades, canopies, hanging shackle, 30 cm down rod and without speed regulator suitable for 230V/240V, 50Hz, AC supply confirming to IS 374/2019 as required complete. (similar to Make: Usha, Model: Energia 32 or equivalent) as per AAI approved make list.

SH: 19- POINT WIRING/TELEPHONE WIRING, POWER POINT

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for group controlled (looped) light point/ fan point/ exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit,and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.

2 X 1.5 sq. mm +1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm +1 X 2.5 sq. mm earth wire

2 X 4 sq. mm +1 X 4 sq. mm earth wire

2 X 6 sq. mm +1 X 6 sq. mm earth wire

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit/raceways as required.

2 X 1.5 sq. mm +1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm +1 X 2.5 sq. mm earth wire

2 X 4 sq. mm +1 X 4 sq. mm earth wire

2 X 6 sq. mm +1 X 6 sq. mm earth wire

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.

Supply installation and testing and commissioning of 20 Pair telephone distribution board in a M.S. box with hinged cover/ door complete with krone type tag block with double jumpering facility mounted on a bakelite sheet etc. including terminations of cable as required.

Supplying and fixing of following sizes of medium class Steel conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

20 mm (For Telephone line)

25 mm (For CCTV & LAN etc.)

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.

3 pin 5/6 A socket outlet

Telephone socket outlet

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.

1 or 2 Module (75 mmX75 mm)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 A & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supply and fixing of following size of under floor GI raceways for distributing cabling in screed floor installations particularly suitable for application requiring EMC screening. Raceway should be made up of Pre galvanized sheet with thickness of 1.6mm consist of body and cover. It should have average of 120GSM zinc coating. Raceway should be openable from top. Cover fitted on to the body with self forming screw and can be opened easily if required. Raceway should be supplied with required accessories such as fixing brackets and coupling plates complete as required

225 mm wide x 38 mm deep raceway (3 compartment)

150 mm wide x 38 mm deep raceway (3 compartment)

100 mm wide x 38 mm deep raceway (1 compartment)

50 mm wide x 38 mm deep raceway (1 compartment)

Supply and fixing of following size of under floor crossover Junction box for Raceways for direct access to cables at the intersection of Raceways supplied completely with base and cover plate(lid). Junction box should be made of Pre galvanized sheet consist of body and cover. Junction box should be supplied with the metal cover for protecting the junction box during constructions and all accessories complete as required:

Installation, testing and commissioning of LED ceiling fittings (2x2 ft. ) of all sizes and shapes, complete with all accessories including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

Installation, testing and commissioning of pre-wired LED tubelight/ downloghter fitting complete with all accessories and tube/lamp etc. directly on ceiling/ wall, including connections with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

Installation of exhaust fan upto 450 mm sweep in the existing opening, including louvers, making good the damage, connection, testing, commissioning etc. as required.

Installation of wall bracket fan upto 400 mm sweep including, connection, testing, commissioning etc as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

Supply and fixing call bell/ buzzer suitable for single phase, 230 V complete as rquired.

SH: 20 - MCB's / DB's

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/ Isolator).

12 way (8 + 36), Double door

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)

12 way, Double door

6 way, Double door (For F&B)

Supplying and fixing 63 Amps FP, 240 / 415 volts, RCBO having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 32 Amps 2Pole, 240 / 415 volts, RCBO having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

Single pole

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

SH: 21- EXTERNAL LIGHTING

Supplying and fixing of 40/35 watt LED, IP-65 post top lantern with spherical cover including all accessories etc. as reqd. as per approval of EIC (Similar to Havells Ruby (Clear) or equivalent).

Providing and fixing of 2.5 Meter height pole fabricated with GI pipe "(Medium-B Class) of dia. 65 mm i/c welded M S base plate of size 250x250x10 mm, painting, etc for mounting of 45/35 watt LED post top lantern including with termination box of suitable size and making foundation to erecting the pole etc. complete as reqd, as per drawing and AAI specification.

SH: 22- INTERNAL & EXTERNAL SIGNAGES

S.I.T.C of following sizes Single Sided openable glow sign board of thickness 70mm minimum. Signage shall be made out of 1.44mm thick aluminum extruded profiles with concealed hinged profile system, extrusions with anodizing / epoxy powder coating of approved shade & colour. The text (in two language) / signage matter shall be electro cut computerized automated self-adhesive vinyl graphics of 3M black out film and yellow message to be created by using 3M yellow 3630-015 translucent film, to be transferred on front side of clear cast acrylic sheet of 5 mm thick of A-cast make of malaysia, acrylic sheet to be pasted with 3M VHB (Very High Bond) double side adhesive tape in extruded aluminum section and easy for graphic changes, (single sided shall have 1.5mm thick Aluminum sheet for back). The illumination source shall be of LED's (CREE / Nichia / Sharp/ Philips (Lumade) / Osram/ Edison) with suitable individual current regulator & driver suitable for operation on 150-270V AC, 50Hz supply and LED shall be fixed inside the frame to obtain uniform illumination, Lumen output – 100 lumen per watt, mean life (burning hours)-50000 hrs burning life with 80% output, along with required internal wiring, connectors, earthing the body etc. Signage board shall be suitable for ceiling /wall/side mounting. Complete job, as required, as per specifications & approved drawing and direction of Engineer-in-charge.

SIZE 400 mm (L)x 400mm(W) x 70 mm(D)

SIZE 1200 mm (L)x 400mm(W) x 70 mm(D)

S.I.T.C. of retro reflective sign boards made of 4 mm thick ACP Sheet (ACP sheet of make Aludecor / Alstrong / Eurobond / Timex), one side face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting of 3M / Avery Denison make conforming to type-IV of ASTM-D4956-01 in blue/green and silver white or other colour combination as approved by Engineering-In-Charge including subject matter, message (bi-lingual), symbols and borders etc. as per IRC ; 67:2001, pasted on substrate by an adhesive backing which shall be activated by applying pressure conforming to class-2 of ASTM-D-4956-01 and fixing the same with suitable sized aluminum alloy rivets @ 30cm c/c to back support frame, complete job as reqd, as per approved drawing, specification and direction of Engineer-in-charge. [Note:- structural steel frame shall be charged separately.]

Supply and fixing of MS Structure along with riveted, bolted or welded in built up sections, trusses and framed work, including cutting, welding, hoisting, fixing in position and applying two priming coat & colour of approved EIC, complete, as reqd.

Providing and fixing frame work made of stainless steel pipe & rectangular section of grade 304 including cutting, welding, grouting, buffing, polishing & fixing in position, complete job, as reqd. as per approved drawing and satisfaction of Engineer-in-Charge.

SH: 23 - LIGHTNING PROTECTION SYSTEM

Providing & fixing of conventional Lightning Arrestor of 1.0 mtr long copper pipe i/c 5 spikes and base complete as required.

Supply of multi stranded 70 Sq. mm. copper conductor flexible Cable confirming to IS 694 amended upto date complete as required.

Laying of one number multi stranded 70 Sq. mm. copper conductor flexible Cable of 1.1 KV grade in existing PVC/MS/GI pipe of size 25 Sq. mm. as required.

Providing and fixing of 25 mm dia 1.6 mm thick PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

Providing and fixing of 25 mm dia medium class GI Pipe along with accessories in surface/recess/ground including cutting the wall/road and making good the same in case of recessed pipe as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required.

SH: 24 - EARTHING

Earthing with GI earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm GI strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

SH: 25 - FIRE ALARM AND DETECTION SYSTEM

Supplying, installation, testing & commissioning of repeater panel wih 320 character/ Touch screen LCD display with inbuilt reset, acknowledge and silence switches complete as required.

Supplying, installation, testing & commissioning of intelligent addressable multi criteria detector (Smoke + Heat) complete with mounting base complete as required.

Supply, installation, testing and commissioning of Intelligent addressable Control Module (output module) for tripping of AHU & Ventilation complete with termination etc. complete as required and as per enclosed specifications.

Supplying, installation, testing & commissioning of intellegent addressable manual call point complete as required.

Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required.

Supplying & laying of 2 x 1.5 sqmm FRLS armoured cable, 600 / 1000V rated with annealed copper conductor as per applicable IS standared complete as required.

SH: 26 - FIRE FIGHTING SYSTEM

SITC of electric driven pump suitable for fire hydrant operation complete in all respect and consisting of the following: Horizontal type centrifugal, split casing pump of cast iron body and bronze impeller with stainless steel shaft, to ensure minimum pressure of 3.5 kg/cm2 at highest / farthest end at specified flow of 900 LPM at 35 m head complete with mechanical seals, safety relief valve etc. Suitable HP Squirrel cage Induction motor suitable for operation on 415V, 3 phase, 50Hz, AC supply for the above pump rating with synchronous speed of 1500 RPM, IE-3, TEFC type confirming to IS-325 with IP:55 protection for enclosure, horizontal foot mounted with class F insulation, coupling & coupling guard with the pump complete. Common bed plate fabricated from MS channel / ISMB with spring type vibration isolators. The pump set base shall be held by bolts grouted in the suitable cement concrete foundation duly as per recommendation of OEM, plastered and painted including foundation bolts, washers complete etc. as required.

Design, fabrication, assembling, supply, installation, testing and commissioning of outdoor type cubicle LT panels suitable for 415 V, 3 phase, 4 wire 50 Hz AC supply system fabricated in compartmentalized design from CRCA sheet steel of 2 mm thick for frame work IP 42 degree of protection and 3 mm thick for gland plates i/c cleaning and finishing complete with 7 tank process for powder coating in approved shade, having 100 A capacity of TPN Aluminimum alloy busbar of high conductivity, DMC/SMC busbar supports, and common GI earthbar of size 25 mm X 5 mm with 2 Nos. earth studs, connection from main busbar to switchgears with require size of copper wire & control wiring with 2.5 sqmm FRLS insulated copper conductor cable, cable alleys, cable gland plates and all MCCBs shall be thermal magnetic release having overload, short circuit adjustable setting & (Ics = Icu) i/c accessories as per specification and providing switchgears, metering instruments etc. complete as required.

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :

150 mm dia

100 mm dia

80 mm dia

25 mm dia

Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/1239 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. complete as required.

100 mm dia

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipments on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. (a) 30 Meter

Supplying and fixing single headed external yard hydrant valve with 1 No 63 mm dia instantaneous Gun metal coupling and cast iron wheel, ISI marked, confirming to IS 5290 (type A) with cap and chain as required.

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required.

150 mm dia

100 mm dia

80 mm dia

Supplying, fixing, testing and commissioning of 25 mm dia. ball valve with brass ball complete with nuts, bolts, washers, gaskets complete as required.

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :

100 mm dia

Supplying and fixing 63 mm dia, 15 Meter long RRL hose pipe with 63 mm dia male and female Gun metal couplings duly binded with GI wire rivets etc. conforming to IS 636 (type-A) as required.

Supplying & fixing 63 mm dia gun metal branch pipe with 20 mm nominal internal diameter size, nozzle confirming to IS 903, suitable for instantaneous connection to interconnect hose pipe coupling as required.

Supply, installation , testing commissioning of pressure gauge of 100 mm dia., 0-21 kg/sq.cm range with 15 mm dia stop cock valve, piping etc complete as required.

Providing & fixing of differential pressure switch in M.S. pipe line including nipple, socket, etc. complete connection etc. as required.

Supplying and fixing of wall mounted hose cabinet made out of 2 mm thick FRP, 32” x 24” x 10” size, to accommodate two 15m length of delivery hose and branch pipe, acrylic fronted double door, with lock, 2 keys and a break glass recess for keys duly painted with post office red externally and white internally with synthetic enamel paint complete in all respect, for internal / external hydrant as required. Make: NewAge/ Minimax

Supply and laying of 4X2.5 sq.mm. copper conductor XLPE insulated PVC sheathed unarmoured control cable from the pump starter panel to pump and differential pressure switch complete as required.

SH: 27 - LT PANELS, STREET LIGHT PANEL

MAIN L.T PANEL - Sub-Station Design, fabrication, assembling, supply, installation, testing and commissioning of Indoor type cubicle LT panels suitable for 415 V, 3 phase, 4 wire 50 Hz AC supply system fabricated in compartmentalized design from CRCA sheet steel of 2 mm thick for frame work IP 42 degree of protection and 3 mm thick for gland plates i/c cleaning and finishing complete with 7 tank process for powder coating in approved shade, having 400 A capacity of TPN Aluminimum alloy busbar of high conductivity, DMC/SMC busbar supports, with bottom base channel of MS section not less than 100mm X 50 mm X 5 mm thick, entire panel shall have a common GI earthbar of size 50 mm X 5 mm at the rear with 2 Nos. earth studs, solid connection from main busbar to switchgears with require size of aluminium busbar & control wiring with 2.5 sqmm FRLS insulated copper conductor cable, cable alleys, cable gland plates and all MCCBs shall be thermal magnetic release having overload, short circuit adjustable setting & (Ics = Icu) i/c accessories as per specification and providing switchgears, metering instruments etc. complete as required.

Incomer- 250A, 36KA (at 415Volts), Ics=100% Icu rating Four Pole, MCCB- 02 Nos. & having Electrical and Mechanical interlocking with both incomers with Bus Coupler. 1 Set of RYB phase indicating LED lamps controlled by 5 amp MCB. 1 Digital Multifunction meter Bus Coupler- 300A, 36KA (at 415Volts) , Four Pole, MCCB- 01 1 Set of RYB phase indicating LED lamps controlled by 2 amp MCB. Bus Bar : Aluminium TPN Bus Bar- 400 Amps. (1 Set) Outgoing - 160 A, 25KA, Four Pole, MCCB - 02 Nos. 125 A, 25KA, Four Pole, MCCB - 02 Nos. 63 A, 25KA, Four Pole, MCCB - 04 Nos. 32 A, 25KA, Four Pole, MCCB - 04 Nos. 1 Set of ON/OFF Red and Green LED indicators in each control switch.

LT Panel for Switch Room Supplying, installation, testing and commissioning of cubical MV out door type electrical LT panel with IP 54 protection, suitable for 415 V, 3 phase, 50 Hz AC supply system fabricated in compartmentalized design from CRCA sheet steel of 2 mm thick for frame work and covers, 3mm thick for gland plates i/c cleaning & finishing complete with 7 tank process for powder coating in approved shade, DMC/ SMC bus bar supports, bottom base channel of MS section not less than 100 mm x 50 mm x 5mm thick, fabrication shall be done in transportable sections, entire panel shall have a common aluminimum earth bar of size 50 mm x 5mm at the rear with 2 Nos. earth stud, solid connections from main bus bar to switch gears with required size of Al. bus bars and control wiring with 2.5 sq.mm. PVC insulated copper conductor S/C cable, cable alleys, cable gland plates. (as per specification & drawing), i/c providing following switch gears:-

Incomer- 125A, 36KA (at 415Volts), Four Pole, MCCB- 02 No. & having Electrical and Mechanical interlocking with both incomers with Bus Coupler. 1 Set of RYB phase indicating LED lamps controlled by 5 amp MCB. 1 Multifunction meter Bus Coupler- 125A , 36KA (at 415Volts) , Four Pole, MCCB- 01 1 Set of RYB phase indicating LED lamps controlled by 2 amp MCB. Bus Bar : Aluminium TPN Bus Bar- 200 Amps. (1 Set) Outgoing - 63 A, 25KA, Four Pole, MCCB - 4 Nos. 32 A, 25KA, Four Pole, MCCB - 4 Nos. 1 Set of ON/OFF Red and Green LED indicators in each control switch.

STREET LIGHT FEEDER PILLAR Design, fabrication, assembling, supply, installation, testing and commissioning of suitable size dust & vermin proof, Indoor type, wall mounted control panel for street light, fabricated with 14 SWG CRCA Sheet complete with detachable gland plate and front hinged door locking arrangement duly powder coated of approved shade, required MCB/Contactors/auto manual switch/MCB LED indicator lamp/Busbar of capacity 50 A along with other accessories including all connections, inter connection, wiring with minimum 2.5 sqmm FRLS copper wire & provision for earth connection etc complete as required:

SH: 28 - LT CABLES

Supply of following size of XLPE insulated & PVC sheathed, armoured aluminium conductor cable of 1.1KV grade as per latest IS code with latest amendments etc. complete as required.

3.5 X 150 Sq.mm.

3.5 X 70 Sq.mm.

4X 25 Sq.mm.

Supply of following size of XLPE insulated & PVC sheathed, armoured copper conductor cable of 1.1KV grade as per latest IS code with latest amendments etc. complete as required.

4X 10 Sq.mm.

4X 4 Sq.mm.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Upto 35 sq. mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing masonry open duct as required.

Upto 35 sq. mm

Above 35 sq. mm and upto 95 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.

Upto 35 sq. mm (Clamped with 1mm thick saddle)

Above 35 sq. mm and upto 95 sq. mm (Clamped with 25x3 mm MS flat clamp)

Above 95 sq. mm and upto 185 sq. mm (Clamped with 25/40x3 mm MS flat clamp)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

3½ X 150 sq. mm (50mm)

3½ X 70 sq. mm (38mm)

4 X 25 sq. mm (28mm)

Supplying and making end termination with brass compression gland and Copper lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.

4 X 10 sq. mm (25mm)

4 X 4 sq. mm (19mm)

SH: 29 - PA System

SITC OF 6” Ceiling Speaker Rated Power Output 1.5W-3W-6W, Line Input 100V or 70V, Frequency Response 100-13KHz, SPL(@1W/m) 91dB, Speaker Unit 6” full range paper cone, Cutout Size 220mm, Dimension 245(D)×69(H)mm, Material Metal enclosure and metal grille in white, Mounting Way In-ceiling spring clip quick installation, suitable Weight, Metal enclosure and metal grille in white, In-ceiling quick installation by spring clip etc all complete as required. Approved makes: Bronx/Bose/Tannoy

SITC of Weather proof Horn Speaker 30W Outdoor Horn Speaker, Rated Power Output 30W, Line Input 100V or 70V, Frequency Response 380-6.5KHz, SPL(@1W/m) 107dB, IP Rate IP66, Connector by speaker cable tail, Dimension 246(D)×292(H)mm, Net Weight 2.1kg Material Aluminum enclosure and stainless metal bracket in white Mounting Way Quick installation by supplied stainless mounting bracket, Ideal for outdoor paging and speech use in school, office, hotel and airport, Economy rang weatherproof horn speaker complete as required. Approved makes: Bronx/Bose/Tannoy

SITC of Volume Control Vol Control - 40W,Power(RMS): 20W/40W/60W, Impedance: 8 ohms, Line Voltage: 70V/100V AC of suitable Dimension etc. complete as required. Approved makes:Bronx/Bose/Tannoy

SITC of Controller 6 Amplifier, Rated Power Output 500W, Line 1-2 Inputs 385mV, 10kΩ balanced Combo, Line 3-6 Inputs 350mV, 10kΩ, RCA, Frequency Response 80Hz~20kHz THD＜1% at RMS,1KHz, S/N Ratio >70dB, Speaker Output 100V AB 8 zone speaker outputs, REC Output 200mV, Voice Message MP3 or WMA format, two separate players of SD card with protection cover, programmable voice message up to 255, 10 years valid, Operation Environment Operation Temp: +50C to +400C ; Store Temp: -200C to +700C; Operation Humidity: <95%, Power Consumption 600W, Power Supply AC230V or 115V & DC24V etc complete as required. Approved makes: Bose/Yamaha / Bronx

SITC of Remote Paging Microphone, Power Consumption 3W, Zone Capacity 12 Zones, System Capacity y 32 Remote microphones, Line Inputs 350mV, 10kΩ, Mic Input 5mV, 600Ω, Frequency Response 80Hz~16kHz, THD＜1% at RMS,1KHz, S/N Ratio >70dB, Operating Temp -200C to +700C, Power Sup ly DC24V, ±20, Humidity <95% no condensation, suitable dimension and weight etc. complete as required. Approved makes: Bronx/Bose/Tannoy

SITC of rack mounted Media Player with 19" (483 mm wide) rack mounting, depth (build in) in mm 303, power supply 230 VAC, USB 32 GB up to 9999 songs, supported file format MP3, WMA, unbalanced outputs 2 x RCA, IR remote included, applicable in 100V, Net weight product (kg) 4.50 approx., height- rack units (1U=44 mm), depth (incl front) in mm 314, CD/ SD card 32 GB up to 9999 songs, balanced outputs 2 x XLR, other/digital outputs 1 x optical + 1 x coaxial, RS232 control, applicable low impedance etc. complete as required. Approved makes: Denon/ Apart/ Sony

SITC of 9U Equipment Rack with Air Cool fan, 2 Nos. Power Strips, 2 Nos. of rack plates, Cable Routing Perforation, 4 Spin Wheels with Two vertical supporting rails allows for the mounting of units. The horizontal space between these mounting rails is set at a minimum of 17.75 inches, si any unit being The vertical placed screw holes in the rack are spaced at 0.50 inch and 0.60 inch (on an alternating basis).This is totally in harmony with the standard 1.75 inch panel height, known as 1U, and all installed panel must be compliant multiple of that 1.75 inch 1U unit size etc. complete as required. Approved Makes Bronx/Bose/Tannoy

Supply & laying of 1.5 sqmm speaker cable in existing conduit/ pipes etc. complete as required. Approved Make: Finolex, Bronx

Supply & Laying of 25 mm flexible pipe on surface/ above false ceiling etc. complete as per site requirement.

Supply & Laying of 25 mm PVC Conduit on surface/ above false ceiling etc. complete as per site requirement.

Supply & laying of 3CX1.5 sqmm FRLS PVC insulated copper conductor Power cable cable in the existing surface/ recessed steel/ PVC conduit/ raceways as required. Approved Make Finolex, PolyCab

Supply & laying of I/O face plate with gang box on surface etc. complete as required.

SH: 30- SAFETY EQUIPMENTS

Providing and fixing Carbon-di-oxide fire extinguishers consisting of welded M.S cylindrical body, squeeze lever discharge valve fitted with internal discharge tube, 30cms long high pressure discharge hose, discharge nozzle, floor mounted trolley, initial charging, finished externally with red enamel paint including suitable MS frame floor mounted stand complete as required. Capacity 4.5kg. I.S.I. Marked. (IS : 2878)

Providing and fixing ABC type (stored pressure) extinguisher of having 6 Kg Capacity as per IS : 13849 - 1993 consisting of welded MS cylindrical body, with discharge hose, discharge valve initial filling including suitable MS frame floor mounted stand etc complete as required.

Supply and fixing of Class A, 2 mm thick, electrical insulating mat conforming to IS-15652-2006 specifications, ISI marked suitable for working voltage upto 3.3 KV of approved colour from a CPRI approved manufacturer etc complete as required.

Providing of 10 Ltr. Capacity GI Bucket (04 nos. in each set) painted in post office red colour with prior coat of Red Oxide paint and written with white paint "FIRE" and mounted on MS Angle iron frame with bracket of appropriate size and capacity including fillings sand etc. complete as required.

Supplying of Rubber hand gloves suitable for 11kV grade .

Supplying and fixing of Shock treatment chart both in Hindi & English and framed with 5mm thick glass as required.(Frame A2 Size).

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Supply of First Aid Box with medicines, accessories as approved by St.John Ambulance Brigade/Indian Red Cross conforming to IS:2217-1963.

Supplying and fixing of Wall mounted wooden Key Board with cover of suitable size with 40 key pins etc complete as required.

Supplying and fixing single line diagram, schematic diagrams etc. of A1 size on suitable Aluminium sheet including lamination etc. as required complete on wall.

SH: - 31 - MISCELLANEOUS ITEMS

Supply installation, testing and commissioning of recessed bi level drinking water fountain along with Water purifier, with double SS bubbler. Drinking water fountain with mechanical and sensor both operation with 8GPH cooling capacity stainless steel body, approx size 1003mmX Depth 400 mmX height 1035mm, SS bubbler guard operated between 50 to 120 PSI, with MDCU29 antimicrobial touch part, with water ways are lead free material chilling unit suitable for R134a refrigerant, adjustable thermo state, Green building, GRIHA,TUV And NSF Certified, supply complete with all accessories with 100 micron strainer, (similar to Model- M8CRY-Oasis or equivalent) Make- Oasis/ Sunrock/ Filtrin

SITC of STAINLESS STEEL Hand Dryer Made up of SS 304 Body Top. Fan Motor cum heater assembly for hot air blowing, Temperature over heat protection, Sensor for auto operation, Auto timer protection, Low Noise suitable for 230v 50hz supply for Hand Drying Applications complete as required. Make: Anand Automatic Systems/Kopal

Design, Supply, Installation, Testing and Commissioning of Automatic bi-parting (2 Leafs) Sliding doors operator in modular design including internal cover with 12 mm thick clear toughened glass shutters along with suitable capacity EC drive. The frame profile should be separated from the main profile for enabling reduction in vibration and better sound insulation. Microprocessor control unit should be self learning with the adjustable parameters for opening and closing speed, hold-open time, opening and closing force, night lock, multi sensor detectors, inbuilt batter backup in controller profile section, suitable for operating on 230V +5%, 50 Hz AC supply, complete as required. Each glass shutter shall have electromagnetic locking arrangement and Manual Locking Arrangement and fit for existing opening as required. Opening Size Max. : Upto 2400(W) X 2400(H) approx. Make: Dorma/Geze/Hafele/Gilgen/Linox

Supply, installation, testing and commissioning of following Automatic Stainless Steel Air Curtains with in built sensors suitable for entry/exit doors in City side and Air Side of Terminal Building as per site requirement and direction of EIC. a) 1800 mm length.

Supply, installation, testing and commissioning of 5KVA, 170-270 Volt , 50 Hz,1 Phase input and 220 ± 1 Volt , 50 Hz, 1Phase output online UPS along with Sealed Maintenance Free battery bank giving a back up of minimum 30min. at full load as per tender specification along with inbuilt over voltage protection and all accessories including interconnecting cables, lugs, Base Frames, Battery Rack & Battery Circuit breaker complete as required.

Supply, Installation, Testing and Commissioning of Hydro Pneumatic Pump System (01 Working + 01 Standby ) veridical in-line multi stage booster centrifugal SS-316 pump motor sets of size 1.5 HP (1.1 KW) with Flow 9000 LPH at Head 25 Mtrs (Each Pump) suitable for Operation on 415 V, 50 Hz, 3 Phase AC Supply with 100 Ltr. Pneumatic balancing tank, mounting skid, foot valve, GI Suction & discharge pipes, fittings, cast brass/virgin brass valves, CI Strainers suction head, etc. each pump shall have TEFC 2900 RPM 3 Phase electric motor includes pressure switches, VFD based control panel with starters, protection relays, cable, interlocking with level and pressure switches, suction, delivery piping all connections etc. complete as required. Makes: Grundfos/ Wilo/ Kirloskar

Quazar Infrastructure Private Limited