Replacement of CI/GI pipe of different sizes and rewinding of motors and repair of pumps, replacement of starters and other misc items at Faridkot Mil Stn

Amount

Taking proper shut down in writing, disconnecting all the electrical connections, dismantling the motor from the base plate and transporting the same for repair to workshop for rewinding, dismantling the motor/rotor, cutting and removing the old heated up/burnt winding of the stator/rotor, cleaning the slots,bearing,bushes etc ,rewinding the motor stator/rotor with super enameled copper winding wire of existing size , gauge and turns etc including all the insulating materials ie.varnish ,china glass paper,'F' class paper, insulating paper etc and transportation back the same after winding , reassembling at original position and testing complete of electric motor 75 HP to 100 HP,3 phase,415 volts,AC supply all as specified and directed . Notes:- (a) The contractor shall return the motor within week’s time after handing over for repairs to contractor otherwise a penalty of Rs. 1000/- per day will be charged from the contractor. (b)The rates quoted shall be deemed to include the cost of loading/unloading, transportation, nuts bolts and washers of any size and shape as required at site and refixing of serviceable motor duly functional and testing complete at its existing location/position complete all as specified and directed. (c)The contractor shall arrange a visit of Engr-in-Charge to workshop for each job and cutting of complete burnt winding of motor shall be done in presence of Engr-in-Charge.

All as per Ser item No 01 here in before but of capacity 30 to 45 HP, 3 phase 415 volts AC supply complete all as specified and directed .

All as per Ser item No 01 here in before but of capacity 10 to 20 HP, 3 phase 415 volts AC supply complete all as specified and directed .

All as per Ser item No 01 here in before but of capacity 3 to 5 HP, 3 phase 415 volts AC supply complete all as specified and directed .

All as per Ser item No 01 here in before but of capacity 1 to 2 HP, 3 phase 415 volts AC supply complete all as specified and directed .

M&L disconnecting/dismantling , strip opening and overhauling of pumping set of any make and capacity of 75/100 HP, taking out bearing, bushes, impeller and coupling plates etc and greasing of bearings with superior quality and replacement of brass bushes,tyre coupling,slip, impeller grinding,rusted nut bolts and washer,seal etc and lath work on shaft including proper alignment and re-assembling,installing at original position and testing to the entire satisfaction of Engineer-in-Charge complete all as specified and directed .

All as per item No 06 here in before but of capacity 30 to 45 HP, complete all as specified and directed by Engineer in Charge.

All as per item No 06 here in before but of capacity 3 to 5 HP, complete all as specified and directed by Engineer in Charge.

All as per item No 06 here in before but of capacity 1 to 2 HP, complete all as specified and directed by Engineer in Charge.

S&F in repair Star Delta Starter,fully automatic, suitable for 30 HP, 415 volts complete all as specified and directed.

S&F in repair Star Delta Starter, fully automatic, suitable for 50 HP, 415 volts complete all as specified and directed.

S&F in repair Star Delta Starte,r fully automatic ,suitable for 75 HP, 415 volts complete all as specified and directed.

S&F in repair Star Delta Starter ,fully automatic, suitable for 125 HP, 415 volts complete all as specified and directed.

Supply and fixing in repair Digital soft starter suitable for 100 HP 3 phase centrifugal pump specially used in heavy duty applications XLP8 Adaptive acceleration feature ,comprehensive motor protection ,built in RTD and thermister inputs 99 event logs with time stamping power through operation to run soft starter even if 1 analog output fully programmable overload trip,real time metering and monitoring , kickstart constant current ,forward /reverse jog large LCD KEYPAD,2 motor data set,control voltage from 94 VAC to 480 VAC ,Starter communication timeout,I/O expansion card (optional) as directed and specified .

S&F in replacement of sluice valve of size 300mm,class PN-1.6 ( ISI marked) with brass spindle, flanged end including jointing with Neoprene rubber gasket, nuts, bolts and washers etc as per existing complete all as specified & directed .

S&F in replacement of sluice valve of size 250mm,class PN-1.6 ( ISI marked) with brass spindle, flanged end including jointing with Neoprene rubber gasket, nuts, bolts and washers etc as per existing complete all as specified & directed .

S&F in replacement of sluice valve of size 200mm,class PN-1.6 ( ISI marked) with brass spindle, flanged end including jointing with Neoprene rubber gasket, nuts, bolts and washers etc as per existing complete all as specified & directed .

S&F in replacement of sluice valve of size 150mm,class PN-1.6 ( ISI marked) with brass spindle, flanged end including jointing with Neoprene rubber gasket, nuts, bolts and washers etc as per existing complete all as specified & directed .

S&F in replacement of sluice valve of size 100mm,class PN-1.6 ( ISI marked) with brass spindle, flanged end including jointing with Neoprene rubber gasket, nuts, bolts and washers etc as per existing complete all as specified & directed .

S&F in replacement of sluice valve of size 80mm,class PN-1.6 ( ISI marked) with brass spindle, flanged end including jointing with Neoprene rubber gasket, nuts, bolts and washers etc as per existing complete all as specified & directed .

S & F in replacement Cast Iron Non return valve conforming to ISI-5312 suitable for 300 mm bore pipe, heavy duty ,both end flanged with by pass charged of pressure rating PN 1.6 and jointing with rubber or fibre board gasket complete with and including required nos size of nuts, bolts and washers complete all as specified.

M&L for plain cement concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) as in kerbs/coping/bed plates and the likes including weathering, slightly rounded or champhered angles with necessary formwork for pipe support , finishing even and smooth without using extra cement complete all as specified and directed

Taking up or down GI water tubing of bore 15mm including all fittings complete all as specified and directed .

Taking up or down GI water tubing of bore 20mm including all fittings complete all as specified and directed .

Taking up or down GI water tubing of bore 25mm including all fittings complete all as specified and directed .

Taking up or down GI water tubing of bore 40mm including all fittings complete all as specified and directed .

Taking up or down GI water tubing of bore 50mm including all fittings complete all as specified and directed .

Taking up or down cast iron water mains including all fitting with spigot or socket ends and lead joints including burning out joints and recovering lead for 80/100 mm bore pipes complete all as specified and directed.

Taking up or down cast iron water mains including all fitting with spigot or socket ends and lead joints including burning out joints and recovering lead for 200 mm bore pipes complete all as specified and directed.

Taking up or down cast iron water mains including all fitting with spigot or socket ends and lead joints including burning out joints and recovering lead for 300 mm bore pipes complete all as specified and directed.

M&L for CI fitting for spigot & socketed pipes of bore upto 300 mm i.e bends, tapers, tee pieces ,caps & plugs etc complete all as specified and directed .

M&L for Steel water tubing of 15 mm bore, medium grade, galvanised, with all fittings, laid in trenches/ fixed to wall etc complete all as specified and directed .

M&L for Steel water tubing of 20 mm bore, medium grade, galvanised, with all fittings, laid in trenches/ fixed to wall etc complete all as specified and directed.

M&L for Steel water tubing of 25 mm bore, medium grade, galvanised, with all fittings, laid in trenches/ fixed to wall etc complete all as specified and directed .

M&L for Steel water tubing of 40 mm bore, medium grade, galvanised, with all fittings, laid in trenches/ fixed to wall etc complete all as specified and directed.

M L for Steel water tubing of 50 mm bore, medium grade, galvanised, with all fittings, laid in trenches/ fixed to wall etc complete all as specified and directed .

Dismantling existing lead joint of 80 mm bore pipe and providing new run lead joint using old retrieved lead & additional lead, if reqd at site complete all as specified and directed .

Dismantling existing lead joint of 100 mm bore pipe and providing new run lead joint using old retrieved lead & additional lead, if reqd at site complete all as specified and directed .

Dismantling existing lead joint of 300 mm bore pipe and providing new run lead joint using old retrieved lead & additional lead, if reqd at site complete all as specified and directed .

S&F in repair gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe & fixed for 50 mm dia of pipe complete all as specified and directed.

S&F in repair gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe & fixed for 40 mm dia of pipe complete all as specified and directed.

S&F in repair gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe & fixed for 25 mm dia of pipe complete all as specified and directed.

S&F in repair gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe & fixed for 20 mm dia of pipe complete all as specified and directed.

S&F in repair gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe & fixed for 15 mm dia of pipe complete all as specified and directed.

Excavation in trenches n.exc 1.5 m wide & n.exc 1.5 m in depth for foundation/pipe lines etc and getting out in soft/loose soil complete all as specified and directed .

Returning, filling in including spreading, leveling, watering & and well ramming in layers n.exc 25 cm in soft/loose soil complete all as specified and directed .

Removing excavated material to a distance n.exc 50 m & depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed .

S&F in replacement 50 mm bore, cast iron, air release valve, flanged type with two air out lets including jointing with nuts, bolts, washers and rubber sheet etc complete all as specified and directed .

Supply and laying cast iron pipes of 80mm bore with spigot and socket ends centrifugally cast, class LA ,laid in trenches all as specified and directed.

Supply, laying, jointing, commissioning and testing ductile iron pipes of 100mm bore with spigot and socket ends ,centrifugally cast (spun), class K-9, conforming to IS-8329-2000, in any length with & including rubber push (tyton) joint, laid in trenches complete all as specified and directed .

Supply, laying, jointing, commissioning and testing ductile iron pipes of 200mm bore with spigot and socket ends ,centrifugally cast (spun), class K-9, conforming to IS-8329-2000, in any length with & including rubber push (tyton) joint, laid in trenches complete all as specified and directed .

Supply, laying, jointing, commissioning and testing ductile iron pipes of 300mm bore with spigot and socket ends ,centrifugally cast (spun), class K-9, conforming to IS-8329-2000, in any length with & including rubber push (tyton) joint, laid in trenches complete all as specified and directed .

Supply only tail piece of size 300mm suitable for ductile iron pipes of 300mm bore complete all as specified and directed . Note :- A Sum of Rs. 4,03,400.00 will be deducted on account of credit for dismantling/demolished/taking down material. Please refer detail on srl page No 20 (Schedule of credit) of Tender Documents.

M/S BSS AND SONS

Vinod Kumar Bajaj

NEW AMRITSAR CONSTRUCTION COMPANY