SPL REPAIR TO ELECTRIC WIRING AND SUPPLY IN BLDG

Amount

Taking down point wiring with aluminium/ copper conductor for light point, socket point/ power point etc. in PVC casing and caping, surface pvc/ steel conduits, wood batten with clips including taking down board any type and size complete with any type of switches, sockets, holders, (batten or pendent type), ceiling rose etc. The light fittings (any type), main switches, distribution board with MCB’s of any capacity and make are to be removed/ replaced if required and all as specified and directed. NOTE: - Existing fan regulator (any type) and electric meters are to be refixed and connected properly where required.

Point wiring with 1.5 Sqmm copper conductor FRLS (Multistrand) PVC insulated ISI Marked unsheathed cable in and including PVC concealed conduit not less than 20mm dia with IS 9537 (Part-III) 1983 marking, medium grade, ISI marked with all fittings/ accessories as specified in preamble 1 (a) to (q) of Section 19 of SSR Part-II, under heading point wiring, cutting chases, making good in cement mortar (1:3), finishing surfaces to match with existing and also including PVC insulated ISI marked unsheathed 1.5 Sqmm copper multistranded conductor FLRS as earth wire (green colour) connected to common earth dolly for modular fitting, modular box sunk for mounting of switches, sockets, fan regulators, light fittings etc. covered with 3mm thick plastic laminated sheet (Make Hylum or equivalent ISI marked) for one light point or one fan point through regulator or one bell point, controlled by one way switch/ push button complete all as specified and directed.

All as per serial item No '2' above, but for one 3 pin 5 Amps socket outlet on the same board all as specified and directed.

All as per serial item No '2' above, but for one 3 pin 5 Amps socket outlet, independent all as specified and directed.

All as per serial item No '2' above, but for one light point controlled by two way switch all as specified and directed.

All as per serial item No. '2' above but for 3 pin 15 Amps socket out let independent with 2.5 Sqmm PVC copper conductor cable and and PVC insulated, unsheathed 2.5 Sqmm stranded copper conductor cable as continuous earth wire, all as specified and directed.

Point wiring with 1.5 Sqmm copper conductor FRLS (Multistrand) PVC insulated ISI Marked unsheathed cable in and including PVC casing and caping of approved size, double lock type, medium grade, ISI marked with all fittings/ accessories as specified in preamble 1 (a) to (q) of Section 19 of SSR Part-II, under heading point wiring and also including PVC insulated ISI marked unsheathed 1.5 Sqmm copper multistranded conductor FLRS as earth wire (green colour) connected to common earth dolly for modular fitting and including modular box sunk for mounting of switches, sockets, fan regulators, light fittings etc. covered with 3mm thick plastic laminated sheet (Make Hylum or equivalent ISI marked) for one light point or one fan point through regulator or one bell point, controlled by one way switch/ push button complete including making good disturbed surfaces to match with existing all as specified and directed.

All as per serial item No '7' above, but for one 3 pin 5 Amps socket outlet on the same board all as specified and directed.

All as per serial item No '7' above, but for one 3 pin 5 Amps socket outlet, independent all as specified and directed.

All as per serial item No. '7' above but for 3 pin 15 Amps socket out let independent with 2.5 Sqmm PVC copper conductor cable and and PVC insulated, unsheathed 2.5 Sqmm stranded copper conductor cable as continuous earth wire, all as specified and directed.

Switch piano flush type, single pole, one way, 5 Amps, all as specified and directed.

Socket outlet two & three pin 5Amp flush type, all as specified and directed.

Switch piano, flush type, single pole, one way, 15 Amps, all as specified and directed.

Switch socket outlet two in one, 3 Pin 5 amps and 15 amps, flush type, all as specified and directed.

Switch piano flush type, single pole, two way, 5 Amps, all as specified and directed.

Lamp holder, PVC/ Polycarbonate type with back plate suitable for angular/ batten fittings, all as specified and directed.

Ceiling rose, 65 mm to 50 mm, two to three terminals, PVC/ Polycarbonate, insulated body fixed on PVC block, all as specified and directed.

Bell push switch, flush type, single pole, 5 Amps, one way, all as specified and directed.

Electric bell, Ding Dong AC, 230 volts, single pole, all as specified and directed.

Renewal of wall mounted LED integrating batten fitting T5, 10 Watt LED, 2 feet, PVC extruded with 10 watt LED tube rod with all acessoreis prewired and making connection with 3 core copper flexible cable of size 23 x .0076 from ceiling rose/ PVC connector to light complete, all as specified and directed. Make : Havell's Cat Part No. LHEBTP7UN1W009/ C&S cat pART nO LTTB4F10WLEDP/W/ Philips CAT Part No BN021LED10S-6500 PSU GRS1 or equivalent in makes mentioned in Appx 'C'.

Renewal of wall mounted LED integrating batten fitting T5, 20 Watt LED, 4 feet, PVC extruded with 20 watt LED tube rod with all acessoreis prewired and making connection with 3 core copper flexible cable of size 23 x .0076 from ceiling rose/ PVC connector to light complete, all as specified and directed. Havell's Cat Part No. LHEBTP7UN1W018/ C&S cat pART nO LTTB4F20WLEDP/W/ Philips CAT Part No BN021LED20S-6500 NW PSU GR or equivalent in makes mentioned in Appx 'C'.

Renewal of bulk head LED light fitting, 10 Watts with deep drawn anodised aluminium body, epoxy white powder coated, heat resistant prismatic glass cover with specially designed glass cover with 10 watts LED lamp with all acessoreis prewired and making connection with 3 core copper flexible cable of size 23 x .0076 from ceiling rose/ PVC connector to light complete, all as specified and directed. Make :Crompton Greaves Cat Part No. CG80IB10WLEDor equivalent in makes mentioned in Appx 'C'.

Renewal of mirror optics linear and compact 9 Watt mirror light with decorative grey end caps, polycarbonate body and ribbed opal diffuser complete with all accessories and fixtures with extruded polycarbonate, environmental friendly with 9 watts LED tube rod/ lamp with all acessoreis prewired and making connection with 3 core copper flexible cable of size 23 x .0076 from ceiling rose/ PVC connector to light complete, all as specified and directed. Make : Havell's Cat Part No. LHEXARP7PN1W009 or equivalent in makes mentioned in Appx 'C'.

Renewal of sheet metal enclosures for DBs when MCBs to be used, tripple pole and neutral, 4 way, double door (Acrylic door), 240 volts with 200 Amp rated bus bar (When MCB's are to be used) including taking down ICDP/ DB's any type, kit kat fuse, MCB's any type, all as specified and directed. Make : IndoAsian Cat Part No. 811849 or equivalent in makes mentioned in Appx 'C'.

Renewal of sheet metal enclosures for DBs when MCBs to be used, tripple pole and neutral, 6 way, double door (Acrylic door), 240 volts with 200 Amp rated bus bar (When MCB's are to be used) including taking down ICDP/ DB's any type, kit kat fuse, MCB's any type, all as specified and directed. Make : IndoAsian Cat Part No. 811851 or equivalent in makes mentioned in Appx 'C'.

LED lamps, 7 watts all as specified and directed. Make:- CAT Part No LHLDERUEML8X007 of make "Havells" or equivalent in makes mentioned in Appendix "C".

LED lamps, 3 watts all as specified and directed. Make:- CAT Part No LHLDERUEML8X003 of make "Havells" or equivalent in makes mentioned in Appendix "C".

Renewal of 15 Watts recess mounted powder coated pressure die-cast aluminium housing, faceted anodised aluminium reflector, heat resistant toughened clear glass cover mini recess mounting LED down lighter including PC diffuser and integrated electronic driver including making electric connections with suitable copper wire and testing after installing, all as specified and directed. Make : IndoAsian Cat Part No. "ENDURANEOHESURFACEDLS15WLED840S" or equivalent in makes mentioned in Appendix 'C'.

Renewal of MCCB any size/ capacity with MCCB 4 pole 250 Amps 36KA microprocessor release & suitable thimbless/ extended terminal with nuts, bolts and washers etc including minor required additional/ alternation for fixing and connecting up of MCCB all as specified and directed.Make : IndoAsian Cat Part No 830443 or equivalent in Makes mentioned in Appendix "C".

Renewal of sheet metal enclosures for DBs when MCBs to be used, single pole and neutral, 8 way, double door, 240 volts with 200 Amp rated bus bar, all as specified. Make : "Indo Asian" Cat Part No. 811805 or equivalent in makes mentioned in Appx 'C'.

Renewal of sheet metal enclosures for DBs when MCBs to be used, single pole and neutral, 8 way, double door, 240 volts with 200 Amp rated bus bar, all as specified. Make : "Indo Asian" Cat Part No. 811807 or equivalent in makes mentioned in Appx 'C'.

Renewal of sheet metal enclosures for DBs when MCBs to be used, single pole and neutral, 4 way, double door, 240 volts with 200 Amp rated bus bar, all as specified. Make : "Indo Asian" Cat Part No. 811805 or equivalent in makes mentioned in Appx 'C'.

MCB TPN 100 Amp, 415 Volts, 10 kA all as specified. Make : Havell's Cat Part No DHMJCFPF100/ C&S Cat Part No. CSMBH4C100 or equivalent makes mentioned in Appx 'C'.

MCB SPN 63 Amp, 240 Volts, 10 kA all as specified. Make : Indo Asian Cat Part No. 811154 or equivalent makes mentioned in Appx 'C'.

MCB SPN 6 to 32 Amp, 240 Volts, 10 kA all as specified. Make : Indo Asian Cat Part No. 811144 to 811151 or equivalent makes mentioned in Appx 'C'.

MCB SP 6 to 32 Amp, 240 Volts, 10 kA all as specified. Make : Indo Asian Cat Part No. 811122 to 811129 or equivalent makes mentioned in Appx 'C'.

Renewal of sub main wiring with two single core, FLRS, PVC insulated cable 1100 volts grade with copper stranded RLS conductor of size 10 Sqmm (2 single run) with one continuous FRLS copper earthing lead wire of size 6 Sqmm and drawn into PVC concealed conduit with all fittings/ accessories, junction boxes 1 to 4 way 20mm dia, connecting with MCB's or bus bars with suitable size of copper lugs, cutting chases in walls and making good in cement mortar (1:3) including finishing surfaces to match with existing and connected to common earth dolly including taking down old unservicable submain wiring, complete and as directed.

Renewal of sub main wiring with two single core PVC insulated cable 1100 volts grade with copper stranded RLS conductor of size 10 Sqmm (2 single run) with one continuous FRLS copper earthing lead wire of size 6 Sqmm and drawn into PVC conduit/ casing & capping with all fittings/ accessories, junction boxes 1 to 4 way 20mm dia, connecting with MCB's or bus bars with suitable size of copper lugs, cutting chases, making good in cement mortar (1:3), finishing surfaces to match with existing and connected to common earth dolly including taking down old unservicable submain wiring, complete and as directed. Note for Serial Item No 37 & 38:- Two runs (Each run of one RM) of 10 sqmm copper conductor and one run (Each run of one RM) of earth wire of 6 Sqmm, shall be measured as one RM).

Renewal of sub main wiring with two single core, FLRS, PVC insulated cable 1100 volts grade with copper stranded RLS conductor of size 6 Sqmm (2 single run) with one continuous FRLS copper earthing lead wire of size 4 Sqmm and drawn into PVC concealed conduit with all fittings/ accessories, junction boxes 1 to 4 way 20mm dia, connecting with MCB's or bus bars with suitable size of copper lugs, cutting chases in walls and making good in cement mortar (1:3) including finishing surfaces to match with existing and connected to common earth dolly including taking down old unservicable submain wiring, complete and as directed.

Renewal of sub main wiring with two single core PVC insulated cable 1100 volts grade with copper stranded RLS conductor of size 6 Sqmm (2 single run) with one continuous FRLS copper earthing lead wire of size 4 Sqmm and drawn into PVC conduit/ casing & capping with all fittings/ accessories, junction boxes 1 to 4 way 20mm dia, connecting with MCB's or bus bars with suitable size of copper lugs, cutting chases, making good in cement mortar (1:3), finishing surfaces to match with existing and connected to common earth dolly including taking down old unservicable submain wiring, complete and as directed. Note for Serial Item No 39 & 40:- Two runs (Each run of one RM) of 6 sqmm copper conductor and one run (Each run of one RM) of earth wire of 4 Sqmm, shall be measured as one RM).

Renewal of 36 Watts LED, 600mm X 600 mm X 70 mm, ultra mordern recess mounting luminaire with high brightness SMD LED suitable for srmstrong ceiling including making electric connections with suitable copper wire and testing after installing, all as specified and directed. Make : Havell's Cat Part LHEWBPP7PL1W036 or equivalent in makes mentioned in Appendix 'C'.

Mild steel galvanised iron tubing light grade for cable protection in crossing drain of 40mm size. Make of GI tubing:- Makes as mentioned in Appendix 'C'.

Mild steel galvanised iron tubing light grade for cable protection in crossing drain of 50mm size. Make of GI tubing:- Makes as mentioned in Appendix 'C'.

Cutting of roads foundations of laying of cables/ GI pipes not exceeding 1.5 metres wide and not exc. 1.5 metres in depth and making good disturbed surfaces to match with existing by returning filling in, providing soling, WBM and cold bitumenous macadam of existing thicknesses all as specified and directed.

Excavation in trenches for foundations, laying of pipes, cables and manholes in soft/ loose soil n.exc 1.50 metres wide and but exc 1.50 metres deep and getting out complete all as specified and directed.

Returning filling in (soil) including spreading, levelling, watering and well ramming in layers n.exc 25cm thick in any type of soil complete all as specified and directed.

Removing excavated soils to a distance not exceeding 50 metres and deposting where directed at a level not exceeding 1.50 metres above the starting point complete all as specified and directed.

Sand cushioning to under ground cables provided with a layer of sand 8 cms thick before laying the cable and 15 cms thick after laying the cable complete all as specified and directed.

Sub class "B" bricks for covering to cable laid dry flat, with width equal to length of bricks all as specified and directed.

XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross sectional area 70 Sqmm 3.5 core laid in trenches passing through pipe/ ducts/ surface of wall ceiling etc including testing complete and taking out old unservicable cable all as specified.

XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross sectional area 35 Sqmm 3.5 core laid in trenches passing through pipe/ ducts/ surface of wall ceiling etc including testing complete and taking out old unservicable cable all as specified. Note for 50 & 51:- Excavation & Earth work, cable cover, GI tubing and sand cushioning shall be measured and paid separetly.

Pole mounting bracket made out of galvanised iron pipe 25mm dia, light grade of length 1.50 metres with two clamps made out of mild steel flat 25x4 mm with nuts, bolts and washers complete accesseries including two coats of aluminium paint after preparation of surfaces and taking down existing unservicable brackets all as specified and directed.

Renewal of roadway lighting luminaire, LED street light 25 watts, IP-66 having aluminium housing with toughned glass on 9.00 metres poles/ walls including aluminium pvc insulated wire 2 sqmm as required at site and connecting the same to the cable with the help of the connector all as specfied and directed by Engineer-in-Charge including taking down existing unservicable lights. Make:- Cat Part No LSTO-25-CDL of Crompton or equivalent in makes mentioned in Appendix 'C' .

Renewal of aluminium strip 25x3.15mm with saddles and fixing screws etc. for roof conductors and down conductors above ground, all as specified and directed.

Renewal of air termination, single pointed, copper rod 12mm dia and 300mm long, all as specified and directed.

Renewal of test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 nos. 8mm dia 25mm long hex. head screw, all as specified and directed.

Earthing complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25 metre deep below normal ground level) with top edge of plate not less than 1.5 metre below ground level, connecting to galvanised iron wire 4.0mm dia (as earth lead wire), by means of bolt, nuts, check nuts and washer of galvanised and earth wire protected by provision of galvanised iron pipe light grade, 15mm bore including provn of concrete pit in PCC M-15, type B-I using 20mm graded crushed stone aggregates with 40mm thick cover of RCC M-15, type B-I, reinforced with XPM (weight not less than 4 kg/ Sqm) and frame of angle iron 25x25x3mm with lugs 2 Nos and with 6mm dia mild steel bar handle made to shape, galvanised iron medium grade 20mm bore pipe for watering perforated at bottom 1.75 metre long placed on top edge of earth plate, common salt and charcoal filling, test point made out of phosphorous bronze with fixing arrangement, funnel, wire mesh and including earth work in any type of soil, returning filling in and removal of surplus soil to a distance not exceeding 50 metre, all as per electrical plate No. 3 of SSR 2009 Part-I and connection to earth test point all as specified and testing on completion.

M/s. Rishav Sood

Havish Construction

M/S KEWAL SONS

m/S Varun Gupta

M/S Ajay Kumar Mahajan