REPAIRS TO SUNKEN FLOOR, SEEPAGE / LEAKAGE, CHAJJAS, ROOF AND CERTAIN MAINT WORKS IN ZONE - I AREA OF DRDO TOWNSHIP, PHASE - I, C V RAMAN NAGAR, BENGALURU

Amount

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) and disposing of debris outside MD land complete all as specified and as directed.

Demolition of cement concrete (un-reinforced) of any discription and in any position, and disposing of debris outside MD land complete all as specified and as directed.

Demolition of cement concrete reinforced of any description and in any position not otherwise specifically provided for; including reinforcement cut as required to facilitate demolition, and disposing of debris outside MD land complete all as specified and as directed.

Taking down cement plaster of any description including raking out joints, hacking for key, scrubbing down with water, etc., and disposing of debris outside MD land complete all as specified and as directed.

Uprooting or scrubbing plants / shrubs / flora / fauna on walls, girth not exceeding 100 mm, cutting holes in walls, digging out roots applying sulphuric acid / phenolic acid as per manufacturers instructions to burn out deep grown roots and making good the surface using CM 1:3 (mixed with and including water proofing compound) complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

Demolition of brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, separating and stacking the serviceable material and disposing the unserviceable material outside MD land complete all as specified and directed.

Material and labour for Pre-cast cement concrete block masonry with grade ‘C’ solid blocks exceeding 10 cm in width, having minimum compressive strength of 50 Kg / Sqcm as per IS 2185 (Part- I) 2005 and set in CM 1:6 complete all as specified and as directed.

Material and labour, reinforced cement concrete, M-15 (nominal mix), using 20 mm graded stone aggregates, as in chajjas, complete all as specified and directed. Note: Reinforcement and formwork shall be measured and paid separately under relevant items of this schedule

Material and labour, reinforced cement concrete, M-15 (nominal mix), using 20 mm graded stone aggregates, as in slabs, shelves, etc., complete all as specified and directed. Note: Reinforcement and formwork shall be measured and paid separately under relevant items of this schedule

Material and labour, Precast RCC 1:2:4 type B1 (using 20mm stone aggregate) as in cover slab of drain, culvert and the like, set in CM 1:4 all as specified and as directed. Note: Reinforcement shall be measured and paid separately under relevant item of this schedule

Use and waste formwork to Chajjas, chullah hoods, troughs and similar surfaces, finishing concrete surfaces rough complete all as specified and as directed.

Use and waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work;not exceeding 200mm thick (Horizontal or sloping) finishing concrete surfaces rough complete all as specified and as directed.

Use and formwork to edges of concrete flats, treads, breaks in floors, window cills concrete railing, openings in concrete walls, floor and roofs and sides of RCC bands in walls, horizontal or sloping and similar work exceeding 10 cm but not exceeding 20 cm wide fair finished surface of concrete complete all as specified and as directed.

Material and labour, steel reinforcement using TMT bars of 10 mm dia and over, cut to length, bent to shape required, including cranking, bending and binding with mild steel wire (annealed) and not less than 0.9 mm dia complete all as specified and directed.

Material and labour, steel reinforcement bars, using TMT bars of 6 to 8 mm dia and over, cut to length, bent to shape required, including cranking, bending and binding with mild steel wire (annealed) and not less than 0.9 mm dia complete all as specified and directed.

Supply and fix, Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240complete all as specified and as directed.

Material and labour, Rolled mild steel framed work such as in doors or gates of angle, or tee sections with gusset plates, rails, braces, etc. completely drilled for fixing of steel sheeting or other covering, doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging doors fittings (exclusive of steel sheeting or other covering, running rails and guides) and handing also fastening and fixing complete Gde Fe 410 - W (Grade-E- 250) quality-A complete all as specified and as directed.

Material and labour for, mild steel work as in framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and as directed.

Supply and fix Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and as directed.

Material and labour for Plain Cement Concrete (1:5:10) type E2, using 40 mm graded stone aggregate as sunken slab filling mass concrete, complete all as specified and as directed.

Material and labour for Plain Cement Concrete, (1:2:4), type B1, using 20 mm graded stone aggregates as in plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwok, finishing the surfaces even and fair, complete all as specified and directed.

Material and labour for Plain Cement Concrete, (1:2:4), type B1, using 20 mm graded stone aggregates as in haunching, padding concrete (including mixing with water proofing liquid as per manufacturers instructions) for obtaining uniform slope on roof top and finishing the surface even and smooth without using extra cement complete all as specified and directed. Note : Supply only liquid based water proofing compound will be measured and paid for separately under respective item.

Supplying only integral waterproofing liquid complete all as specified and as directed.

Supply and fix powder Coated aluminium frames and shutters (minimum thickness of powder coating 50 microns) and fabricating of doors, windows, ventilators and fixed partitions with one or more rebates including necessary joining cleat, glazing clips, rubber packing, snap bending crews etc. complete all as specified and as directed. Note :- i) For payment purpose weight of aluminium section shall be measured and paid, ii) Cost of aluminium mongery. lock, rubber packing, rollers for sliding shall be deemed to include in the quoted rate, iii) Sheet glass and wire gauge shall be measured and paid for separately under respective items.

Dismantling unserviceable GI roof sheet, Supply and fixing Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified complete all as specified and as directed.

All as per item No. 26 here- in- above but plain steel sheet all as specified and as directed.

Material and labour for, 25 mm thick Plain Cement Concrete, (1:2:4), type B-0, using 12.5 mm graded stone aggregate as in flooring complete all as specified and as directed.

Material and labour for, 75 mm thick Plain Cement Concrete, (1:4:8), type D2, using 40 mm graded stone aggregate as in sub-base / flooring complete all as specified and as directed.

Material and labour for, 75 mm thick Plain Cement Concrete, (1:3:6), type C1, using 20 mm graded stone aggregates, as in paving/ plinth protection laid in panels including necessary form work, finishing the surfaces of concrete even and fair complete all as specified and as directed.

Renewing non-skid ceramic tiles in patches area not exc.5 sq m, preparing the beds and laying of new tiles setting jointing, pointing etc and matching with the existing surfaces, over and including screed bed of 15 mm thick in CM 1:6, complete all as specified and as directed.

Renewing glazed ceramic tiles in patches area not exc.5 sq m, preparing the beds and laying of new tiles setting jointing, pointing etc and matching with the existing surfaces, over and including 10 mm thick backing coat in CM 1:3, complete all as specified and as directed.

Demolition of stone slabs of any thickness and in any position, providing material and labour, for 18 to 20 mm thick Granite work (of any type), table rubbed and mirror polished), in single piece in steps, jambs, pillars, window-cills, cooking platform and like set in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, making hole for gas pipe, edges made half round, laid over and including screed bed or bedding layer of 15 mm thick in CM (1:6), complete all as specified and as directed.

Demolition of stone slabs of any thickness and in any position, providing material and labour, for 20 - 25 mm thick Cuddapah Stone slab, (of any type), machine cut, as in cooking platform and like set in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite, making hole for gas pipe, edges made half round, laid over and including screed bed or bedding layer of 15 mm thick in CM (1:6), complete all as specified and as directed.

Demolition of floor, hearth or wall tiling including cement mortar bedding (including backing), removing rubbish off the premises and disposing of outside MD land, and providing, Material and labour, for Glazed ceramic coloured tiles of size 300 mm x 450 mm x 7 to 8 mm laid on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with colour of tiles over and including 10 mm thick backing coat in CM (1:3) complete all as specified and as directed.

Demolition of floor, hearth or wall tiling including cement mortar bedding (including backing coat / bedding), removing rubbish off the premises and disposing of outside MD land, and providing Material and labour, for flooring with non-skid ceramic coloured tiles, 7 to 8 mm thick, (area of tile exceeding 0.06 sq m and not exceeding 0.11 sq m) laid, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with colour of tiles over and including 15 mm thick screed bed in CM (1:4) complete all as specified and as directed.

Demolition of floor, hearth or wall tiling including cement mortar bedding (including backing coat / bedding), removing rubbish off the premises and disposing of outside MD land, and providing, Material and labour, Joint free non-skid Ceramic coloured tiles 7 to 8 mm thick (Grade B-IIA), area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, as in flooring, set and pointed in white or coloured cement to match colour of tiles over and including 15 mm thick screed bed in CM (1:4) complete all as specified and as directed.

Demolition of floor, hearth or wall tiling including cement mortar bedding (including backing coat / bedding), removing rubbish off the premises and disposing of outside MD land, and providing, Material and labour, non-skid Ceramic coloured tiles 7 to 8 mm thick (Grade B-IIA), area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in flooring, set and pointed in white or coloured cement to match colour of tiles over and including 15 mm thick screed bed in CM (1:4) complete all as specified and as directed.

Demolition of floor, hearth or wall tiling including cement mortar bedding (including backing), removing rubbish off the premises and disposing of outside MD land, and providing, material and labour for, skirting / dado with non-skid ceramic coloured tiles (area of tile exceeding 0.11 sq m and not exceeding 0.18 sq m), 7 to 8 mm thick, laid, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match with colour of tiles over and including 10 mm thick backing coat in CM (1:3) complete all as specified and as directed.

Supply and fix Plain Sheet glass 4 mm thick, ordinary quality and glazing with oil putty in square not exceeding 0.5 sq. m in each pane all as specified and as directed.

Supply and fix Figured glass, 4 mm thick, pin head type and glazing with oil putty in squares not exceeding 0.5 sqm in each pane all as specified and as directed.

Material and labour, for Rendering 15 mm thick on brick or concrete surfaces in cement mortar 1:4, finishing the surfaces even and smooth without using extra cement all as specified and as directed.

Material and labour, for Rendering 15 mm thick in two layers on brick or concrete surfaces, base layer of 10 mm thick in CM 1:4 and finishing layer of 5 mm thick in CM 1:4, including mixing with approved water proofing compound, for roof facia, chajjas, etc., and finishing the surfaces even and smooth without using extra cement complete all as specified and as directed. NOTE:- Supply only WPC will be measured and paid separately under relevant item of BOQ.

Material and labour, for Rendering 10 mm thick on brick or concrete surfaces in cement mortar (1:6) and finishing the surfaces even and smooth without using extra cement all as specified and as directed.

Material and labour, for Rendering 5 mm thick on brick or concrete ceiling surfaces in cement mortar (1:3) and finishing the surfaces even and smooth without using extra cement complete all as specified and as directed.

Material and labour, for 15 mm thick rendering in CM 1:3 including mixing approved water proofing compound on fair faces of brick or concrete surfaces, finishing surfaces fair and even and providing 1 mm thick Brushbond RFX (two component acrylic polymer modified cementious coating consisting of Brushbond RFX powder and Nitobond BBX acrylic emulsion grey in colour of Make FOSROC) using stiff brush roller or trowel to obtain desired thickness complete all as per manufacturer's instructions, as specified and as directed. NOTE:- Supply only WPC will be measured and paid separately under relevant item of BOQ.

Preparation of new or previously untreated plastered wall surfaces of any description and applying two coats of oil bound distemper over a coat of alkali resistant primer complete all as specified and as directed.

Preparation of new or previously untreated plastered ceiling surfaces of any description and applying two coats of oil bound distemper over a coat of alkali resistant primer complete all as specified and as directed.

Preparation of new or previously untreated plastered wall surfaces of any description and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified and directed.

Material and labour for, Preparation of new or previously untreated steel surfaces of any description not other wise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of zinc chrome primer complete all as specified and as directed.

Taking down unserviceable GI tubing, supply and fixing new 15 mm bore Galvanized Iron tubing, medium grade, with all fittings, such as Tee, elbows, sockets, unions, short pieces and application of bituminous paint in concealed portion, fixed to wall/ ceiling or laid on floors, complete all as specified and as directed. Notes: i) Taps, valves in any shall be removed before taking down pipe, ii) Cutting chases for concealed piping shall be measured and paid separately under respective item.

Taking down unserviceable GI tubing, supply and fixing new 20 mm bore Galvanized Iron tubing, medium grade, with all fittings, such as Tee, elbows, sockets, unions, short pieces and application of bituminous paint in concealed portion, fixed to wall/ ceiling or laid on floors, complete all as specified and as directed. Notes: i) Taps, valves in any shall be removed before taking down pipe, ii) Cutting chases for concealed piping shall be measured and paid separately under respective item.

Disconnecting existing PVC water tank of capacity exceeding 300 litres and not exceeding 1000 litres (fixed on roof), setting aside (or lowering if required), cleaning, removing all scales, dirt from tanks, from mouths of circulating pipes, etc., and hoisting / re-fixing / re-connecting in same / new position, writing date of cleaning with white paint, (height / size of letters / figures not less than 10 cm in height, re-fixing serviceable ball valve, complete all as specified and as directed.

Disconnecting unserviceable water tanks and Supply and fixing 500 litres capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), triple layered, hoisted and fixed in position all as specified in SSR Part I and as directed.

Disconnecting unserviceable water tanks and Supply and fixing 1000 litres capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), triple layered, hoisted and fixed in position all as specified in SSR Part I and as directed.

Supply and fix Bib taps 15 mm dia, fancy type, chromium plated with CP flange all as per Cat No. HT F3001151 of Cera or equivalent in other makes specified complete after taking down old bib taps all as specified and as directed.

Supply and fix two way, bib taps, fancy type, 15 mm dia, cast copper alloy, chromium plated, with CP flange, screwed for iron pipe or for brass ferrule, all as per Cat No.HT F3001163 of Cera or equivalent in other makes specified complete after taking down old bib taps all as specified and as directed.

Supply and fix Pillar taps, 15 mm dia, fancy type, chromium plated with CP flange, long shank all as per Cat No. F3002101 of Cera or equivalent in other makes specified here-in-after, after taking down old pillar taps complete all as specified and as directed.

Supply and fix in repairs, Vitreous china snow white, wash hand basin of size 550 mm x 400 mm all as per Cat No. No. S2040103 of Cera or techno and commercial equivalent makes specified including supply and fixing PTMT waste coupling of 32 mm dia (minimum weight 45 grams), all as specified and as directed.

Supply and fix, Vitreous china snow white colour floor mount type European Water Closet of size 520 x 360 x 390 mm with PVC seat cover and 'P' trap, fixing at a distance of 300 mm from wall with bolt including connection with flushing cistern and with outlet pipe complete all as per Model CONVENTIONAL, Cat Part Nos B1510101 & S1050102 of CERA Make or equivalent in other makes complete all as specified and directed.

Taking down old plastic seat covers and Supply and fixing EWC seat covers, white closed pattern with recessed bottom, including screws and connectors complete all as per Cat Part No B1510101 of CERA Make or equivalent in other makes complete all as specified and directed.specified and as directed.

Supply and fix in repairs, Vitreous china, white colour, 'Orissa pattern' squatting pan of size 580 mm x 440 mm with UPVC 'P' trap or 'S" Trap, front or back inlet, integral foot rests, connecting to trap, flushing pipe, anti syphonic pipe, complete, all as per Make : Cera, Cat No .S3010102 of CALINA make or techno commercially equivalent in other makes specified complete all as specified and directed.

Taking down old sinks and Supply and fixing Stainless steel sink with draining board, made out of 1.00 mm thick sheet for kitchen over all size 915 mm x 460 mm with bowl size 405 x 355 x 178 mm all as per Cat No.SSSBSD-52 of Blue Star make or techno commercially equivalent in other makes specified including CP waste coupling of 40 mm dia, cast iron cantilever brackets, 40 mm dia 800 mm long corrugated PVC waste pipe, washers, connecting union etc. complete all as specified and directed.

Taking down unserviceable plate rack, supply and fix new Stainless steel plate rack of 0.63mm thick sheet, size 800 mm x 600 mm complete all as specified and directed. Make: Blue star, Model No. SSKPR-313.or techno-commercially equivalent make of NIRALI / ANJALI / JAYNA / DIAMOND.

Supply and fix, in repairs, PVC valve less, syphonic action type, white colour flushing cistern, 10 litres capacity, low level, white, with inlet, ball valve, float and handle including brackets and jointing with and including new existing flush pipe, making good to the disturbed surfaces complete all as per Model No: CIENA PREMIUM Cat Part No B1010101 of CERA Make or techno commercial equivalent in other makes complete all as specified and directed.

Supply and fix in repairs, Stop valves (concealed), fancy type with CP wall flanges, chromium plated, cast copper alloy with long shank and exposed part kit with fittings sleeve, operating lever concealed part screwed both ends for iron pipe or for unions, including making good the disturbed portion matching with adjacent surfaces, complete all as per Cat No.HT F4050103 & HT F3001351 of Cera or equivalent in other makes specified here-in-after, complete all as specified and as directed.

Supply and fix in repairs, Angular cock, fancy type, with chromium plated wall flange, cast copper alloy, screwed both ends for iron pipe or for brass ferrule,15mm dia, complete all as specified and as directed. MAKE:- Cat No. HT F3001201 of CERA or techno-commercially equivalent model in any one of the make as mentioned in list of makes here-in-after.

Supply and fix in repairs, two way Angular stop cock, fancy type, with chromium plated wall flange, cast copper alloy, screwed both ends for iron pipe or for brass ferrule,15mm dia, complete all as specified and as directed. MAKE:- Cat No. HT F3001211 of CERA or techno-commercially equivalent model in any one of the make as mentioned in list of makes here-in-after.

Supply and fix in repairs, Chromium Plated overhead shower rose of size 95 mm with swivel joints, over head shower arm of 230 mm long with wall flange, complete all as specified and as directed. Make : Cera Cat Part No F7020304 & F7040103 or techno and commercial equivalent in other makes specified after taking down old shower rose complete all as specified and as directed.

Supply and fix in repairs, single tube towel rail, brass chromium plated, 600 mm long fixed with chromium plated screws and PVC cleats, complete all as specified and as directed. Make : CERA, Model No F5003103 or techno and commercial equivalent complete all as specified and as directed.

Supply and fix in repairs, Corner glass shelf(medium) 225mmx225mm with chromium plated bracket superior quality complete Make : Cera, Cat Part No F5005102 or techno and commercial equivalent in other makes specified, complete all as specified and as directed.

Supply and fix in repairs, Sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long Make : Jaquar, Cat Part No ACN-CHR-1171N or equivalent in other makes specified complete all as specified and as directed.

Supply and fix, chromium plated, grating doom 100 mm dia (with or without waste hole) after taking down old grating complete all as specified and as directed.

Supply and fix in repairs hand shower for Health faucet, 8 mm dia, 1.2 m long, flexible tube in chrome finish, wall hook with NRV (back flow preventer), all as per Cat Part No ALD-577 of Jaquar or techno commercial equivalent in other makes complete all as specified and as directed.

Supply and fix, Gun metal, globe or gate valves 20 mm bore with iron wheel head screwed both ends for iron pipe and including taking down old gate valve complete all as specified and as directed.

Supply and fix, Ball valves of 20 mm dia , (minimum weight 210 gms) , high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe including taking down old ball valve complete all as specified and as directed.

Supply and fix, PVC connecting pipe 450 mm long 15 mm dia both ends having brass coupling nut and PVC washer after taking down old connecting pipe complete all as specified and as directed.

Supply and fix, PVC connecting pipe 600 mm long 15 mm dia both ends having brass coupling nut and PVC washer after taking down old connecting pipe complete all as specified and as directed.

Supply and fix, PVC (SWR) pipes 40 mm dia, SCH 80 (working pressure not less than 6 Kg/ Sq cm), conforming to IS 4985, fixed with solven cement joints, laid in floors or on walls, and fixed as in drain pipe of wash hand basins, spout pipes, etc., including taking up or down existing PVC pipes and connections complete all as specified and as directed.

Supply and fix, PVC (SWR) bends any radius 40 mm dia of bore fixed in pipes, complete all as specified and as directed.

Taking down eaves gutters, soil / waste / vent pipes / rain water pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., Supply and fix, PVC (SWR) pipes 110 mm dia single socketed in any length with solvent cement joints laid under floor or on walls fixed as soil / waste / vent pipes with Stack clamps made out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall complete all as specified and as directed.

Taking down eaves gutters, soil / waste / vent pipes / rain water pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., Supply and fix, PVC (SWR) pipes 75 mm dia single socketed in any length with solvent cement joints laid under floor or on walls fixed as soil / waste / vent pipes with Stack clamps made out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall complete all as specified and as directed.

Dismantling of unserviceable nahani trap, supply and fix UPVC(SWR) nahani trap 75 mm dia outlet with grating, including fixing and jointing cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregates) complete all as specified and as directed.

Dismantling of unserviceable multi floor trap, supply and fix UPVC(SWR) multi floor trap 75 mm dia outlet with grating, including jointing with solvent cement complete all as specified and as directed.

Dismantling of unserviceable floor trap, supply and fix UPVC(SWR) floor trap 75 mm dia outlet with plain / single hole, CP grating, including jointing with solvent cement complete all as specified and as directed.

Supply and fix, UPVC (SWR) bends any radius for 75 mm dia bore, complete all as specified and as directed.

Supply and fix, UPVC (SWR) bends any radius for 110 mm dia bore, complete all as specified and as directed.

Supply and fix, UPVC (SWR) junction single 'T' equal or unequal 110 mm bore with access door complete all as specified and directed.

Supply and fix, UPVC (SWR) branch piece single 'Y' of bore 75 mm dia, fixed in pipes complete all as specified and as directed.

Supply and fix, UPVC (SWR) branch piece single 'Y' of bore 110 mm dia, fixed in pipes complete all as specified and as directed.

Supply and fix, UPVC (SWR) coupler of bore 110 mm dia, fixed in pipes complete all as specified and as directed.

Supply and fix, PVC (SWR) vent cowl of bore 110 mm dia, including taking down old PVC vent cowl all as specified and as directed.

Taking down old water tank cover and Supply and fixing Polyethylene water storage tank covers circular or any other type with hinges suitable for up to 1000 Ltrs capacity tanks all as specified and as directed.

Taking down unserviceable steel windows with frame without taking of shutter (double leaf/triple leaf shutter with frame i.e. fly proof and glazed) from the frame not exceeding 0.5 Sq m each except grill, including glass panes, mosquito proof mesh complete all as specified and as directed.

Taking down unserviceable steel windows with frame without taking of shutter (double leaf/triple leaf shutter with frame i.e. fly proof and glazed) from the frame exceeding 0.5 Sq m each and not exceeding 3 sq m each except grill, including glass panes, mosquito proof mesh complete all as specified and as directed.

SREE BUILDERS

Kaveri Enterprise

RAMYA CONSTRUCTIONS

Lucky Enterprises

ARATHEERTHA CONCEPTS

C R R CONSTRUCTIONS

Moulya Builders

Solar Electricals and Electronics

Meghana and Gowda Enterprises