WBPWD/EEBED/NIQ-55/2024-25-2nd

Amount

SITC of Automatic Lift ( as per manufacturer design & as per detailed specification below conforming to IS ) and putting into operation after final testing in the existing lift shaft complete with all accessories and repairing the damage wall / floor if any etc to complete as reqd. Make :As per order vide memo no:-75-W(C)/1M-20/15 dated:-03.03.2015 of Principal Secretary , Public Works Department Category-I:-OTIS /KONE/SCHINDLER Category-II-Electromec/LT Elevator/ United Elevator/ Thyssen Krupp/ Bharat Elevator Co. Ltd/Engineer Vertical Services/Escon/Omega / Johnson Type: Passenger Lift . Load : 08 Passenger / 544 Kg Control: Microprocessor based with AC variable voltage & variable frequency ( VVVF) Machine:- Energy efficient machine, Gearless, With Machine Room size-4350mmX3550mm with shaft Size 1900X1900mm(inner measurment) Position of Machine Room: Above the hoistway Speed:1 Mtrs./ Sec Floor served: G+4 Landing: 5, all on same side Total Rise : 10.5 Mtr (Approx) (Bidder should visit the site) Operation: Microprocessor based simplex full collective with or without attendant.

Signals: Digital car position indicator,car travels direction indicator in car & at all landing with call registration indicator.Leveling accuracy:±5 mm(Micro levelling arrangement) CAR: Car inside :1100 mm ( W ) x 1300 mm ( D ) or As per manufacturer's standard conforming to IS Car Entrance : Clear Opening 800 mm (W) x 2000 mm (H ) protected with car door Car Enclosure: Stainless Steel sheet (20 SWG) with Hairline finish with hand rail. Car Ceiling & Lighting: Stainless Steel with hairline finish with LED lighting and Fan Car Ventilation: Pressure fan with anodised aluminium grill. Car Flooring : Decorative granite flooring (As per direcion of EIC and according to this Department's Order). Car Door: Stainless Steel centre opening automatic door provided with V3F controlled door drive system Landing Door: Stainless steel centre opening automatic door provided with V3F controlled door drive system Door Opening: Automatic power oprated door with full length Photocell assembly light curtain sensor PROTECTIVE DEVICES & PWER SUPPLY ASSEMBLY ARD: Automatic rescue device complete with dry maintenance free batteries as required.for automatic evacuation to the nearest floor in case of power failure / single phasing/others.

Overload Protection:Fully loaded with overload protection.On overloading the lift car will not start with door remaining open and give audio display indication Emergency lighting in car: Battery operated emergency lighting in the lift car. Intercom system: Battery operated intercom system in Lift Car, Machine Room & Control Room Emergency Alarm: Battery operated alarm bell system in lift car and control room Fireman switch:Fireman switch at main landing terminal. Voice Synthesizer: Voice announcement system (Voice Synthesizer) in the car to announce the position of the elevator in the hoist way as the car passes or stops at a floor served by the elevator. DIMENSION OF SHAFT & POWER SUPPLY Available Shaft Dimension: 1900(W) mmX 1900(D)mm (Bidder should visit the site) Pit Depth : 1350 mm (Bidder should visit the site) Overhead : 4200 mm (Bidder should visit the site) Electric power supply: AC 415 Volt 3phase, 50 Hz, terminated in machine room as per IS Prior approval of materials make, drawing to be done by the executing agency before delivery of materials at Site Elevator main Steel Wire rope:-Usha Martin make Controller & Drive locking passward must be provide to EIC & also provide Test Certificate for all materials.

Arrangement of Load Hook & Base Frame : Supply, fabrication, fixing of New foundation for LOAD BEEM By M.S. C channel 250mm Joist 150mm X 75mm X 3400mm, HR Sheet/ Plate Ciol 12mm X 10 inch X 10inch with 6Nos. 16mm Hole, HR Sheet/ Plate Coil 10mm X 6mm, M S. Round for Making Load Hook as per marking Both side by Running Welding also Cutting RCC Wall with grouding by WEDGE ANCHOR M-16 x 125 with TAPPER WASHER, SPRING WASHER etc. For Making LOAD HOOK upto 3 TON Capacity in the Machine Room wall. (Make- TATA/ JINDAL).The entire work should be done as per actual site requirement and as per direction of EIC.

Painting of steel/ iron surface with ready mixed paint/primer of approved make, and brand incl. preparation of surface by sand paper/emery paper, cleaning etc. for receiving fresh coat of paint. 2 coat of paint over 1 coat of RO priming. N.B. i) The rate quoted by the manufacturer should be inclusive of cost for providing 2 years DLP after completion of 1 year of initial commisioning ii)The agency will have to take temporary three/single phase electric power connection from WBSEDCL with his own cost. The electric cable for temporary power connection have to be arranged by the agency with his own cost. iii)All the civil foundation works i.e. foundation of Pedestal for placing the machine, placing the joist across the wall of the machine room if required, foundation of the Spring buffer at Lift pit etc have to be done by the agency with his own cost. iv)The safe store for keeping the lift material should be arranged by the agency where there will not be available room with proper locking arrangement. The Department will not be responsible for any theft case of the material. The arrangement of the accomodation of the workers of the lift agency should be done by the agency himself. v) The workers should follow proper safety guideline for this work. The Department will not be responsible for any accident of the workers.

Rates to be quoted will be inclusive of all the taxes incl. GST. No other additional charges will be applicable in addition to the quoted rates.

UNITED ELEVATORS PRIVATE LIMITED (BID ID -6324421)

ELECTROMEC (BID ID -6346363)