Construction of Sarai Bhawan at Bani Mata Temple Village Banni in Tehsil Bharmour Distt. Chamba ( H.P)Deposit work (SH Balance work construction of Sarai Bhawan at Banni Mata Septic tank Soak pit and 4 Nos

Amount

Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains of soil such as pick work, jumper work, blasting work, jumper blasting work soft and hard blasting and saturated soil, de-watering, including wedging out rocks where blasting is prohibited, chiseling or any other mixed variety of soil, including shoring, strutting or bailing out water upto any depth or any height quantum of water including dewatering removal of slush and stacking the serviceable and unserviceable material clear from the edge of excavation and as per direction of Engineer-In-Charge and retuning the stacked soil in 15 cm (Fifteen centimetre) layers, when required into plinths, side of foundation etcetra consolidating each deposited layer by ramming watering and then disposing of all excavated earth as directed by the Engineer-in-charge, within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights/depth of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in flat surfaces such as soffits of suspended floors roofs, landings balconies and access platform including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal one five millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights/depth of propping and centring below supporting floor to ceiling and removal of the same for in-situ reinforced concrete and plain concrete work in flat surfaces such as soffits of suspended floors roofs, landings windows sills, cornices, arches, moulding, corbelling including curved surfaces where ever required as per Architectural drawing, design and specifications and the like floor etcetera including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing form work with steel plates of 3.15mm (Three decimal fifteen millimetres) thick, welded with angle iron in frames of 30x30x5mm (Thirty into Thirty into Five millimetres), so as to give a fair finish including centring, shuttering strutting and propping etcetera, with wooden battens and ballies for all heights and removal of the same for in-situ reinforced and plain concrete work in edges of slab and breaks in floors and walls under any thickness including carriage of material within all leads, lifts and other incidentals as per approved drawing, design, specifications and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Supplying and filling in plinth with sand under floors, including watering, ramming,consolidating and dressing complete including carriage of material within all leads, lifts and other incidentals and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying cement concrete 1:5:10 (One cement isto five sand isto ten graded broken/crushed stone aggregate 40mm (twenty milimetres ) nominal size and down gauge) mechanically mixed and curing complete excluding cost of forms work in foundation and plinth within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and laying Reinforced 1:1.5:3 (One cement is to one decimal five coarse sand) is to three graded stone aggregate 20 mm ( twenty millimetre nominal size cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing and laying Reinforced cement concrete 1:1.5:3 (One cement isto one decimal five coarse sand) is to three graded stone aggregate 20 mm ( twenty millimetre) nominal size)work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Random rubble masonry/polygonal rubble masonry (uncoursed/brought to courses) with hard stones of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (one cement isto six sand isto twelve graded stone aggregate 20mm (twenty millimetre) nominal size) at plinth level in Cement Mortar 1:6 (one cement isto six sand) within all leads, lifts of materials and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive, toll taxes, GST and any other taxes imposed by the Government.

Providing Tor steel reinforcement Thermo Mechanically Treated bars of grade Fe-500D of Tata Tiscon/Sail for reinforced cement concrete work including bending, binding, cutting, straightening and placing in position complete including cost of binding wires complete upto all floor levels as per approved specifications, drawing, design, as per entire satsfaction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Supplying and filling 90mm to 45mm ( ninety millimetre to forty five millimetre ) sice stone aggregate curshed stone aggregate in soak pit including curing complete as per entire satsfaction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Supplying and filling 53mm to 22.4mm ( fifty three millimetre to twenty two decimal four millimetre ) size stone aggregate curshed stone aggregate in soak pit including curing complete as per entire satsfaction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Supplying and filling stone screening 13.2 mm ( thirteen decimal two millimetre ) nominal size ( Type A) in soak pit including curing complete as per entire satsfaction of the Engineer-in-charge including carriage of material within all leads, lifts and other incidentals. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying Cement concrete flooring 1:2:4 (One cement isto two coarse sand is to four graded stone aggregate) 40 mm( forty millimetre ) thick with 20 mm ( twenty millimetre ) nominal size stone aggregatefinished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and applying 15mm (Fifteen millimetre) thick cement plasters in single coat on rough side of brick/concrete/stone walls for interior plastering upto all floor level including arises, internal rounded angles, chamfers or rounded angles not exceeding 80mm (Eighty millimetres) in girth and finished even and smooth witth cement mortar 1:6 (One cement isto Six sand) above plinth level to floor all level complete including carriage of material with in all leads, lifts and other incidentals as per drawing, design and specifications, as per the direction and entire satisfaction of Engineer-in-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 100 mm dia ( hundred millimetre )nominal size PVC of supreme make or S.C.I./C.I. spun fitting & socket waste soil & ventilating pipes ( Lead caulked joint to be measured and paid for seperately) .complete including carriage of material within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing of 100 mm( hundred millimetre ) dia PVC of supreme make or S.C.I./C.I. spun fitting & accessories single equal branches of required degree plain With oval access door insertion rubber washer 3 mm ( three millimetre ) thick, bolts and nuts and curing complete including carriage of material within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 100mm nominal ( hundred millimetre dia metre ) PVC or cast iron cowl.within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing 100 mm nominal size diametre ( hundred millimetre ) lead caulked joints to sand cast / cast iron (spun) iron pipes fittings including testing of joints complete including carriage of material within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Supplying C.I. cover light duty rectangular 455x610mm with frame weight 38 kg ( Single seat ) complete including carriage of material with in all leads, lifts and other incidentals as per drawing, design and specifications, as per the direction and entire satisfaction of Engineer-in-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing Kota stone slab flooring over 20 mm (average) thick with base of cement mortar 1 : 4 (One cement is to four coarse sand) base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete including carriage of material with in all leads, lifts and other incidentals as per drawing, design and specifications, as per the direction and entire satisfaction of Engineer-in-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. complete.including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design, entire satisfaction and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Finishing with wall Deluxe Multi surface paint system for interiors and exteriors as per manufacturers specifications Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Painting wood work with Deluxe MultiSurface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.75 ltr/10 sqm of approved brand and manufacture.within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and fixing M.S. grills Fixed to steel windows by welding of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.within all leads, lifts of materials and other incidentals as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacturewithin all leads, lifts and other. incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providng and laying cemet concrete 1:2:4 (One cement isto two coarse sand) four graded stone aggregate 20 mm ( twenty millimetre nominal size) with drain includng curring complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling thejoints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Brick work using second class common burnt clay building bricks in super-structure above plinth level upto all floor level in Cement Mortar 1:6 (one Cement isto six Sand) and curing complete as per approved drawing design specifications and as per direction and entire satisfaction of the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidentals. The rate is including of octroi, royality, Malkhana, toll tax, sale tax, GST and other taxes imposed by the Government.

Providing and laying in position cement concrete 1:4:8 (One cement isto four sand isto eight graded broken/crushed stone aggregate 40mm (Forty millimetres) nominal size mechanically mixed and vibrated curing complete excluding the cost of centering and shuttering in foundation and plinth including carriage of material within all leads, lifts and other incidentals as per approved drawing, design, specifications and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government

Half brick masonry using second class common burnt clay building bricks in super structure above plinth level upto floor all level in Cement Mortar 1:4 (One Cement isto Four Sand) and curing complete as per entire satisfaction and the direction of Engineer-in-Charge including carriage of materials within all leads, lifts and other incidental.The rate is including of octroi, royality, Malkhana, toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing factory made P.V.C. door frame single rebate of any colour of size 50x47 mm (Fifty into forty seven millimetres) with a wall thickness of 5 mm (Five millimetres), made out of extruded 5mm (five millimetre) rigid PVC foam sheet heat bend & mitred at corners and jointed with 2 (Two) Nos of 150 mm (One hundred fifty millimetres) long brackets of 15x15 mm (Fifteen into fifteen millimetres) M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm (Nineteen into nineteen millimetres) M.S. square tube of 19 (Nineteen) gauge, EPDM rubber gasket weather seal to be provided through out the frame including fixing of door frame to be fixed to wall with M.S. screws of 100 mm (One hundred millimetres) long with wooden or rawl plugs embedded in masonry complete including carriage of material within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing to existing door frames, 30mm (Thirty millimetres) thick factory made PVC door shutter consisting of frame made out of M.S. tubes of 19 (Nineteen) gauge thickness and size of 19 x 19 mm (Nineteen into nineteen millimetres) for styles and 15x15 mm (Fifteen into fifteen millimetres) for top & bottom rails, (Code no. 9.120 ) of Rajshri M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm (Five millimetres) thick heat moulded PVC 'C' channel of size 30 mm (Thirty millimetres)thickness, 70 mm (Seventy millimetres) width out of which 50 mm (Fifty millimetres) shall be flat and 20mm (Twenty millimetres) shall be tapered in 45o (Forty five) degree angle on either side forming styles and 5 mm (Five millimetres) thick, 95mm (Ninety Five millimetres) wide PVC sheet out of which 75mm (Seventy Five millimetres) shall be flat and 20mm (Twenty millimetres) shall be tapered in 45 (Forty Five) degree on the inner side to form top and bottom rail and 115 mm (One hundred fifteen millimetres) wide PVC sheet out of which 75 mm (Seventy Five millimetres) shall be flat and 20 mm (Twemty millimetres) shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided either side of the panel. 10 mm (Ten millimetres) thick, 20 mm (Twenty millimetres) wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm (Five millimetres) thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails , joints mitres and jointed with solvent cement adhesive including fixing of PVC shutter with existing frame with M.S. nutt hinges 100x50x1.90mm (One hundred into fifty into one point ninety millimetres) size with necessary screws etcetra complete including carriage of material within all leads, lifts and other incidentals as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 250x16mm (Two hundred fifty into Sixteen millimetres) nominal size aluminium sliding door bolts ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with nuts and screws etcetera complete, including carriage of material within all leads, lifts and other incidentals and as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 150mm (One hundred fifty millimetres) nominal size aluminium Handles ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etcetera; complete including carriage of material within all leads, lifts and other incidentals and as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 200x10mm (Two hundred into Ten millimetres) nominal size aluminium Tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with nuts and screws etcetera. complete, including carriage of material within all leads, lifts and other incidentals and as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etcetera; complete including carriage of material within all leads, lifts and other. incidentals and further as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing Single rebate angle iron door,window,clerestory window frame manufactured from steel iron section of 40X40X6mm, (forty millimetre into forty millimetre into six millimetre) thickness including hinges jamb,lock jamb,beed and if required angle thrashold ofmild steel angle 50X25 mm (fifty millimetre into twenty five millimetre) welded or rigidly fixed by mechanical means,lugs with split end tails to each jamb including steel butt hinges 2.5 mm (two point five millimetre) thick with provision for locking arrangement and shock absorber as specified and applying a coat of approved steel primer after pre-treatment of the surface etcetera including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing M.S. grills of require pattern in wooden/steel frames of windows etcetra with M.S. Flats, square or round bars with round headed bolts and nuts or by screws complete including entire carriage of materials within all leads, lifts and other incidentals, as per approved drawing, design and as directed by the Engineer-in-Charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing 15mm (Fifteen millimetre) thick cement plasters in single coat on fair side of brick/concrete/stone walls for exterior plastering including making groove or drip course, arises, internal rounded angles, chamfers or rounded angles not exceeding 80mm (Eighty millimetres) in girth and finished even and smooth with cement mortar 1:6 (One cement isto six sand) above plinth level to floor all levels complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing 6mm (Six millimetre) thick cement plaster to ceiling in cement mortar 1:3 (One cement isto Three sand) upto all floor levels complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying 300x300 mm (Three hundred into three hundred millimetres) antiskid (non slippery) ceramic tiles of Nitco / RAK / Kajaria / Orient Bell tiles as per approved shade in flooring on 20mm (twenty millimetre) thick cement mortar 1:4 (one cement isto four sand) finished with flush pointing in white cement including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-In-Charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and laying Coloured glazed tiles of size 300x450mm (three hundred into four hundred fifty millimeters) of orient / Kajaria / Rak in skirting, risers of steps and dado for all heights, laid on a bed of 12mm (twelve millimeters) thick cement mortar 1:3 (one cement is to three sand) and jointed with white cement slurry complete as per approved drawings, specification design and as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Malkhana, Royality, Octroi, toll tax or any taxes imposed by the Government.

Providing and fixing 1216 15mm (fifteen millimetres) Outer diameters Polyethelene-Aluminium / Polyethelene PE-AL- PE Composite Pressure Pipes conforming to IS - 15450 ,2004 of Kitec U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etcetera, with clamps at 1.00 (One) metre spacing for concealed work including cutting chases and making good the wall etcetera. This includes testing of joints complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen millimetre) diametre C.P. brass. Bib tap of Prayag / hindware / Cera approved quality (superior or heavy type) and colour complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen millimetre) nominal bore C.P. brass brass stop cock (concealed) of standard design of Prayag / hindware / Cera including necessary fitting complete including entire carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen millimetres) nominal bore P.V.C. connection pipe with brass union 45cm (Forty five Centimeters) length complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 110x75mm (One hundred ten into seventy five millimetres) nominal size/diameter PVC floor trap ISI marked Finolex/Relpipe(Reliance)/ Vectus Conforming to IS-14735-99 of self cleaning design including fixing with approved adhesive, cost of cutting and making good the wall and floor etcetera complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the

Providing and fixing 100mm (One hundred millimetres) diametre C.P. iron grating of Superior quality of Prayag / hindware / Cera for floor, gully or Nahni trap including neccessary fitting complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government..

Providing and fixing 110mm (One hundred ten millimetre) nominal bore/diametres High pressure PVC waste and ventilating having pressure pipes 4.00 kg/cm2 (Four point zero zero kilogram per centimetre square) of Supreme / Finolex/ Vectus/Relpipe (Reliance) including fixing with approved adhesive etcetera complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 110 mm (one hundred ten millimetre) nominal size PVC single equal branch with oval access door, ISI marked of Finolex/Relpipe (Reliance)/Vectus insertion rubber washer 3mm (Three millimetre) thick including fixing with approved adhesive etcetera complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing water closet squatting pan (Indian type W.C. pan )White Vitreous china Orissa pattern W.C. pan no 20090 of size 530x410 mm (Five hundred thirty into Four hundred ten millimetre) with integral type foot rests with 100 mm (One hundred millimetre) diametre sand cast Iron P or S trap, 10 litre (Ten) low level P.V.C. flushing cistern having dual flush system of Hindware/ Cera/ Jaquar of star white / Snow white shade and as shown in the drawing / as per details including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required necessary fitting complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing vitreous china bowl pattern urinal including connection the urinal with waste pipe by means of white lead mixed with chopped hemp flat back small No 60001 size 63.8x39.5x42 (sixty three point eight into thirty nine point five into forty two) with auto cistern of Cera / Hindware Jaquar as per approved drawing and design directed by the Engineer-in-Charge, as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidentals. The rate inclusive of Malkhana, Royality, Octroi, toll tax or any taxes GST imposed by the Government.

Providing and fixing wash basin White Vitreous China Flat back wash basin Delta No 10010 size 550x 400 mm (Five hundred fifty into four hundred millimetre) (Under counter Basin ) Hindware/ Cera/ Jaquar of star white / Snow white shade and as shown in the drawing / as per details with single 15 mm (Fifteen millimetre) C.P. brass pillar tap with C.I. brackets, 15 mm (Fifteen millimetre) C.P. brass pillar taps, 32 mm (Thirty two millimetre) C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required including necessary fitting complete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and placing on terrace 500 (Five hundred) litre capacity polyethylene water storage tank, tripple layer of Supreme / Finolex / Relpipe (Reliance) / Vectus IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank ccomplete including carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 15mm (Fifteen millimetres) nominal bore/diametre brass ball valve (horizontal plunger type) of Prayag / hindware / Cera without nuts and pipes including necessary fitting complete including entire carriage of material within all leads, lifts and other incidentals as per specifications, approved drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Providing and fixing 600x300mm (Six hundred into Three hundred millimetres) nominal size of Division Plate for Urinals Hindware /cera/Jaquar of star white / snow white shade and (Heavy duty make ISI marked No- 8931 & 8934) of approved quality and colour complete as per architectural drawings including carriage of material within all leads, lifts and other incidentals, as per approved specifications, drawing, design and as directed by the Engineer-in-charge. The rate is inclusive of octroi, royality, Malkhana, Toll tax, sale tax, GST and any other taxes imposed by the Government.

Tripta Devi (BID ID -567527)