Nagercoil Corporation Providing Dinning Hall at Mukkadal dam

Amount

Providing Dinning Hall at Mukkadal dam

Earthwork excavation for foundation in hard stiff clay, stiff black cotton, murrum, gravelstone earth mixed with small size builders and hard gravelly soil and full depth as may be directed except in rock requiring blasting but including shoring, strutting and bailingout watr where ever necessary and refilling sides of foundation with excavated earth in layers of not more than 15cm thick well rammed and consolidated and depositing the surplus earth with in the compound in places as shown by the departmental officers with an initial lead of 10m and an initial lift of 2m clearing, levelling the site etc., complete complying with standard specification.

Plain Cement Concrete 1:4:8 (one cement four fine aggregates and eight coarse aggregates) using 40mm size ISS HBG metal including cost and conveyance of all materials to site and including for the mixing, laying and labour charges and all incidential charges such as water providing etc., complete as per standard specification

Random rubble masonry in CM 1:5 (one cement, five sand) using best new rough and bond stones including simultaneous pointing above ground level with the same mortar including curing, cost and conveyance of all materials and labour charges etc. complete as per Standard specification

Supplying and filling with red gravel in layer of not more than 15cm thick well rammed watered and compacted including cot and conveyance, stacking and filling charges etc. complete as per Standard specification

Providing steel centering for sides and soffits including supports and strutting upto 1:10/1:20 up to 3.29m height for plain surfaces such as RCC slabs, rectangular beams, Tee beams, bed blocks, Culvert body walls, deck slabs, retaining walls, staircase, Landing slab, landing beams, canopy etc., with all cross bracings using mild steel sheets of size 90mm x60mmx10gauge stiffened into welded mild steel angles of size 25mmx6mm for boarding laid over silver oak (Country wood) joists of size 10cmx 6.5cm spaced at 90cm centre to centre and supported by casurina props of 10cm to 13cm dia spaced at 15cm c/c including cost of nails, ropes, all labour charges and incidental charges etc. complete complying with standard specification.(TNBP Spl. No.154 A)

Reinforced cement concrete 1:1½:3 (one cement and half sand and three aggregates) using 20mm ISS Hard broken granite stone jelly for Reinforced cement concrete works excluding cost of shuttering, and cost of reinforcement but including cost and conveyance of materials to work site, all labour charges and incidental charges for mixing and laying concrete,finishing the surface nearly rough, compacting using vibrators, curing etc, complete complying with standard specification.(TNBP No.30)

Supplying, fabrication and placing in position of steel reinforcement using mild steel (or) ribbed tar steel rods, for all RCC works as per the design given by the departmental officers including cost of steel and binding wire and all labour charges for cutting, bending rods, tieing into grills, placing in position etc., complete as directed by the departmental officers.( TNBP No: 15886)

Brickwork in cement mortar 1:5 (one cement and five sand) using country bricks of size 83/4"x41/4"x23/4" including curing, cost and conveyance of all materials to site and all labour charges etc. complete as per standard specifications

Plastering with cement mortar (1:5) 12mm ,thick in all floors including cost and conveyance of all materilas to site and labour charges etc,complete as per standard specifications (S.I.306)

Paving the floor with Vitrified Marbonite tiles of approved quality and colour of size 600x600x8mm thick of approved make, quality and colour in all floors over a base layer of cement mortar 1:3(one cement three sand) 20mm thick and laid straight alignment and pointed neatly with colour cement at the rate of 0.40kg/m2 laid without any air gap in the tiles neatly and fixing in position as per standard specifications and as directed by the departmental officer. The colour & quality of tiles should be got approved by Municipal Engineer before use on work

Supplying and paving the floor with design ceramic antiskid tiles of approved brand and quality (Colour/shade of the ceramic tiles shall be got approved by the departmental officers concerned) of size 200mm X 200mm x 6mm in all flooring over a base mortar using of cement mortar 1 : 3 ( One cement and three sand) 20mm thick laid in situ tructo alignment and pointed with colour cement (White cement mixed with colouring pigment) to suit the colour and shade of the ceramic tiles etc., complete complying with standard specification

Dadooing walls with Glazed tiles of sizes 305mm X 200mm X 6mm size of approved make and quality and colour Set in cement mortar 1:2 (one cement, two sand) over 10 mm base layer plastering and pointing with white cement neatly as directed.

Supplying and fixingin position of European water Closet glzed earthern ware of approved quality with p or s trap confirming to IS-2556 part xii with sand cushion and forming flooring alround the closet using 40mm broken jelly in lime concrete 1:2.5 mix 100mm thick and finishing the top required slope and including necessary connection to easr iron soil pipe by dismantling brick masonry RCC roof / floor slab and making the disturbed portion to original condition without leakage etc complete complying with std, specification and as directed by the departmental officers

Wirinng with 2x1.5sq.mm (22/0.3) PVC insulated SC. unsheathed Cu.Conductor of 1100V garade in suitable PVC rigid pipe on wall and ceiling with PVC accessories and with TW switch box and 5A FT switch inflush with wall covered with hylum sheet of 3mm thick with painting of suitable colour for open PVC light/fan point (for electronic regulator) (5 points per coil)(SD 22)

Supply and fixing of single box type 4'36 W flu fitting complete with electronic ballast with TW round blocks on wall or ceiling with flu tube with PVC unsheathed copper leads from terminals to the fitting(SD 87)

Wirinng with 2x1.5sq.mm (22/0.3) PVC insulated SC. unsheathed Cu.Conductor of 1100V garade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with 150x100x113mm TW switch box for 5A 3 pin non inter locking wall socket with 5A Flush type switch with painting of suitable colour with continuous earth wire connection of 14 SWG TC wire for open PVC Plug point. (SD38)

Supply and fixing of 1200mm (48") sweep AC ceiling fan complete with stepped electronic 300W regulator, with 1 metre down rod with fan clamp with side plates and cross arm of size 450mm(18")(SD 106)

20mm dia PVC coupling

20mm dia pvc Tee

20mm dia PVC Elbow

20mm dia PVC Bend

20mm dia PVC union

110 MM PVC Pipe

110 mm PVC Elbow

20 mm pvc pipe

Suplying and fixing rigid PVC panelled door shutter made from M.S box section of size 19mm x 19mm,19guage covered with heat moulded PVC 5mm thick and width of 50mm to from styles and rails.The pael shall be 5mm thick PVC rigid foam sheet inserted into yhe frame sealed to the styles and rails and 5mm x 25mm PVC beading is provided on all sides with furniture fittings etc.,complete .43 PWD

Supply and fixing of M.S Grills with Doors and Windows with one coat of Red oxide with Primer including all costs such as welding,grinding and fabrication charges, cost and conveyance of all materials to site etc,complete as per standard specification.

Painting two coats with Ready Mixed Enamel Paint over the new iron works of approved quality and colour without priming coat including the cost all materials etc.,complete, in all floors.

Painting two coats with ready mixed Plastic Emulsion Paint approved quality and colour over a priming coat, including thorough scrapping, clean removal of dirt, etc complete and including necessary plaster of paris, putty, wherever required etc, complete as per standard specification. - 10 sq.m

Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc. conforming to IS specification including primer coating and enamal painting as per Design given by the departmental officers etc, complete as per standard specification

Fabricating supplying and fixing of pre painted galvanized iron sheets with the following specification. The materials should be of PPGI tile profile with a red colour or any other approved design 0.47 mm thick 24 guage having width 1050 mm. The sheet should be G.I.base pre painted hot dipped galvanized iron sheet and to be fixed with shelf tapping screws,plastic washer.The washer and screws to be fixed by using minute power machine drilled with out damaging the sheets paint coating to be regular modified polyster coat with zinc coating of Z 120 GSM paint thickness the finish should be terra cotta finish like malabar mangalore tiles finish optional matt finish. The sheet to be fixed with making suitable corrugated,cutting the sheet in to the required ssize and making ornamental designs as per the site condition and as directed by the departmental officers.

Supply and Fixing of weldmesh 7.5 x 2.5 cm 10 guage

A. Pandian

p.kannan

Joseph Arul Raj